Rigid item in the form of an eye, loop, and the like. Designed to be attached to a structural member to establish a tie-down point on equipment. It can be in one piece of several elements. It may include mounting hardware, such as screws, washers, and the like. Excludes:ADAPTER, TIE DOWN, and LATCH ASSEMBLY,VEHICULAR LOADING.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED80953*)
CTXKJSAFE OPERATING LOAD RATING
THE SAFE OPERATING LOAD FOR WHICH THE ITEM IS DESIGNED TO ACCOMMODATE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTXKJAJB2.0*;CTXKJAJB2.0$$JAJB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| LT | KILONEWTONS |
| AS | POUNDS |
| BY | TONS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDTTA000*;MATTDCUA000$DTTB000*;MATTDCUA000$$DTTB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| STA000 | STEEL |
| ST4140 | STEEL COMP 4140 |
| STB000 | STEEL CORROSION RESISTING |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPRB000*;SFTTDDCC000$DMTB000*;SFTTDDCC000$$DMTB000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ALA000 | ALUMINUM ALLOY |
| MTA000 | AMALGAM |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CDB000 | CADMIUM ALLOY |
| CMA000 | CHROMATE |
| CMC000 | CHROMATE MAGNESIUM |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CTA000 | COBALT |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| DCA000 | DICHROMATE |
| DCE000 | DICHROMATE COPPER |
| DCB000 | DICHROMATE POTASSIUM |
| DCD000 | DICHROMATE SODIUM |
| DCC000 | DICHROMATE ZINC |
| LCE000 | DISULFIDE MOLYBDENUM |
| MTC000 | INDIUM |
| IRA000 | IRIDIUM |
| LQA000 | LACQUER |
| MNA000 | MANGANESE |
| MTB000 | MOLYBDENUM |
| NLA000 | NICKEL |
| NLC000 | NICKEL ALLOY |
| NLD000 | NICKEL SULFAMATE |
| XXB000 | OXIDE |
| XXF000 | OXIDE ALUMINUM |
| XXE000 | OXIDE COPPER |
| XXA000 | OXIDE FILM |
| XXC000 | OXIDE IRON |
| XXD000 | OXIDE ZINC |
| PNA000 | PAINT |
| PDA000 | PALLADIUM |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PHB000 | PHOSPHATE IRON |
| PHC000 | PHOSPHATE MANGANESE |
| PHE000 | PHOSPHATE NICKEL |
| PHD000 | PHOSPHATE ZINC |
| PCA000 | PLASTIC |
| PTA000 | PLATINUM |
| PRA000 | PRIMER |
| PRB000 | PRIMER HEAT RESISTANT |
| TTA000 | TITANIUM |
| TTB000 | TITANIUM ALLOY |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
BZQQ*JBREAKING STRENGTH
THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BZQQJZC2.0*;BZQQJZC2.0$$JZC2.1*)
| Table 1 |
| Reply Code (AB18) | Reply |
| Z | KILOGRAMS |
| X | NEWTONS |
| P | POUNDS |
| T | TONS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQBC*JMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQBCJE2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| D | NEWTON |
| E | POUND |
CQHQ*JMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQHQJE2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| D | NEWTON |
| E | POUND |
IF STYLE/REPLY CODE(s) AAG OR AAL WERE ENTERED FOR MRC AAJF, YOU MUST ANSWER MRC (THSD)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG*;AAJFDAAL$$DAAL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
IF STYLE/REPLY CODE(s) AM, NS, RC, RF, RT OR WW WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CMLP and AHYM and AAJD)
IF STYLE/REPLY CODE(s) BA, EM, MJ, SJ, SK, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQQR and AHYM)
IF STYLE/REPLY CODE(s) DD OR TT WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CMLP and AHYM)
IF STYLE/REPLY CODE(s) LH WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQQR and AHYM)
IF STYLE/REPLY CODE(s) NP OR SQ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM)
IF STYLE/REPLY CODE(s) JC, JE, JF, JS, NC, NE, NF, NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CMLP and AHYM and AAJD)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CMLP and CQQR and AHYM)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDNS*;THSDDLH$$DRC*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| BA | BA |
| TT | BUTTRESS |
| DD | DARDALET |
| SM | ISO M |
| SS | ISO S |
| LH | LOWENHERZ |
| EM | M |
| MJ | MJ |
| NP | NPT |
| SJ | SI |
| SK | SI-M |
| SQ | SQUARE |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NM | UNM |
| RC | UNRC |
| RF | UNRF |
| RT | UNRS |
| NS | UNS |
| WW | WHITWORTH |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAA7)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0*;CQQRB2.0$$BM2.0*)
AHYM*JNOMINAL THREAD DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYMJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAV4)
UKAS*DSTRENGTH GRADE DESIGNATION
A NUMERIC AND/OR ALPHA-NUMERIC DESIGNATOR INDICATING THE STRENGTH RATING OF A THREADED FASTENER. THE CODE IS COMPRISED OF TWO NUMBERS, SEPARATED BY A DOT. THE CODE TO THE LEFT OF THE DOT REPRESENTS THE ULTIMATE STRENGTH IN MEGA PASCALS (MPA), WHILE THE NUMBER TO THE RIGHT OF THE DOT REPRESENTS THE YIELD STRENGTH (MEGA PASCALS - MPA) OR STRESS AT 0,2 PERMANENT SET (MPA), DEPENDING ON THE PROPERTY CLASS.
Enter the applicable reply code from the table below
(UKASDAH)
| Table 1 |
| Reply Code (AN67) | Reply |
| AZ | 04 |
| CD | 05 |
| AY | 06 |
| BG | 08 |
| AT | 10 |
| AL | 10.9 |
| CN | 100 HV |
| BA | 11 H |
| AW | 12 |
| AM | 12.9 |
| AX | 14 |
| BB | 14 H |
| AN | 14.9 |
| CP | 160 HV |
| BC | 17 H |
| BD | 22 H |
| CR | 24 |
| CS | 28 |
| AB | 3.6 |
| CQ | 310 HV |
| CB | 33H |
| CT | 37R |
| AP | 4 |
| AC | 4.6 |
| AD | 4.8 |
| CU | 42R |
| CF | 45 |
| CC | 45H |
| AQ | 5 |
| BF | 5 AU |
| AE | 5.6 |
| AF | 5.8 |
| CG | 50 |
| AR | 6 |
| BE | 6 AU |
| AG | 6.6 |
| AH | 6.8 |
| AJ | 6.9 |
| CH | 60 |
| CJ | 70 |
| AS | 8 |
| AK | 8.8 |
| CK | 80 |
| CE | 9 |
| BH | A1 - 50 |
| BJ | A1 - 70 |
| BK | A1 - 80 |
| CL | A2 |
| BL | A2 - 50 |
| BM | A2 - 70 |
| BN | A2 - 80 |
| CM | A4 |
| BP | A4 - 50 |
| BQ | A4 - 70 |
| BR | A4 - 80 |
| BS | C1 - 50 |
| BT | C1 - 70 |
| BW | C3 - 80 |
| BX | C4 - 50 |
| BY | C4 - 70 |
| BZ | F1 - 45 |
| CA | F1 - 60 |
AATK*JEYE INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE AND TERMINATES AT THE INNER PERIPHERY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATKJAC2.0*;AATKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATP*JSHOULDER THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATPJAB2.0*;AATPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATR*JSHANK LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHANK,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATRJLA2.0*;AATRJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATU*JEYE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATUJLB2.0*;AATUJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATV*JEYE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATVJLC2.0*;AATVJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATZ*JEYE STOCK DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATZJLB2.0*;AATZJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CKCG*JDISTANCE FROM EYE STOCK OUTER EDGE TO EYE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CKCGJLC2.0*;CKCGJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUA*JEYE STOCK THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUAJAB2.0*;AAUAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACUU*JBASE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACUUJAB2.0*;ACUUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVH*JSHOULDER DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVHJLC2.0*;AAVHJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRHT*JDISTANCE FROM CENTER OF EYE TO SHANK END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRHTJLA2.0*;CRHTJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWXM*JEYE OUTSIDE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWXMJLA2.0*;CWXMJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGKB*JBASE OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BASE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGKBJLA2.0*;BGKBJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJW*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAJWJL2.0*;AAJWJL2.0$JL2.0*;AAJWJL2.0$$JL2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATBJAB2.0*;AATBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ALUG*JOVERALL BASE HEIGHT
A MEASUREMENT FROM THE BOTTOM OF BASE TO THE TOP OF THE MOUNTING SCREW OR BOLT HEAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALUGJLC2.0*;ALUGJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADMG*JMOUNTING FLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FLANGE, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADMGJLB2.0*;ADMGJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALUL*JOVERALL WIDTH OF THE RING
DISTANCE FROM OUTSIDE EDGE OF BASE TO OUTSIDE EDGE OF HORIZONTALLY ARTICULATED RING.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALULJAA2.0*;ALULJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) S1 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AHYM and AATK and AATP and AATR and AAVH and CWXM and ABHP)
IF STYLE/REPLY CODE(s) S2 OR S3 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AATK and AATP and AAVH and CWXM and ABHP and CQJX)
IF STYLE/REPLY CODE(s) S4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AATP and AATU and CKCG and AAVH and ABHP and CQJX)
IF STYLE/REPLY CODE(s) S5 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AATK and AAUA and AAVH and CWXM and ABHP and AAJW)
IF STYLE/REPLY CODE(s) S6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AHYM and AATK and AATR and AAUA and AAVH and CWXM and ABHP and AAJW)
IF STYLE/REPLY CODE(s) S7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AHYM and AATK and AATR and AATZ and CRHT)
IF STYLE/REPLY CODE(s) S8 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AATU and AATV and AATZ and AAVH)
IF STYLE/REPLY CODE(s) S9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AHYM and AATK and AATP and AATR and CKCG and ACUU and BGKB and ADMG)
IF STYLE/REPLY CODE(s) S10 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AATK and AATP and AATU and CKCG and AAUA and ACUU and AAVH and CWXM and ALUL)
IF STYLE/REPLY CODE(s) S11 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAJF and AHYM and AATP and AATR and AATV and AATZ and AAVH and CWXM and AATB and ALUG)
IF STYLE/REPLY CODE(s) S12 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AATK and AATP and CKCG and ACUU and BGKB)
IF STYLE/REPLY CODE(s) S13 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AATK and CKCG and AAUA and ACUU and BGKB and ABHP)
STYL*LSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLS2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR04311 | S1 | LOAD RING 1 - MALE |
| DR04320 | S10 | ARTICULATED - WELDED |
| DR04321 | S11 | ARTICULATED |
| DR04322 | S12 | ARTICULATED WITH BEARING - WELDED |
| DR04323 | S13 | WELDED |
| DR04312 | S2 | LIFTING RING - FEMALE |
| DR04313 | S3 | LIFTING LOOP 1 |
| DR04314 | S4 | LIFTING LOOP 2 |
| DR04315 | S5 | ROTARY FEMALE |
| DR04316 | S6 | ROTARY MALE |
| DR04317 | S7 | LOAD RING 2 - MALE |
| DR04318 | S8 | BASE WITH BEARING BALL - WELDED |
| DR04319 | S9 | ARTICULATED WITH BEARING - SCREWS |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCGK*;CBBLDCGS$$DCGW*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BGJ | CABLE ASSEMBLY |
| CGE | CLAMP TYPE RING SHIELD |
| CGF | DEE RING |
| CGG | FORELOCK PINHOLE |
| ALW | GROMMET |
| CGH | GROOVED SURFACE |
| CHB | HINGE |
| CGJ | INWARD SAFETY THROAT CLOSURE |
| CGK | KNOCKOUT HOLE |
| CGL | OUTWARD SAFETY THROAT CLOSURE |
| CGM | REMOVABLE LINK |
| CGN | REMOVABLE POINT |
| CGP | RETAINING CHAIN |
| CGQ | RING HOLE |
| CGR | RING SADDLE |
| CGS | SPRING GUARD |
| CGT | TWO STEEL CASTINGS |
| CGW | U-GUARD |
| DBG | W/BOLT |
| DBH | W/O BOLT |
| CBL | WEDGE |
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAR8)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information