A container filled up with a desiccating agent item used to remove water and oil contents in a compressed air discharged from a pneumatic brake circuit.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED68167*)
IF STYLE/REPLY CODE(s) C1, C2 OR C3 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and CSKY)
IF STYLE/REPLY CODE(s) C4, C4, C5, C5, C6 OR C7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAU and CSKY)
IF STYLE/REPLY CODE(s) C8, C9, C10, C11, C12, C15, C16, C17 OR C18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAU and CSKY)
IF STYLE/REPLY CODE(s) C13 OR C14 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAU and CSKY and CSLQ and CSMD)
IF STYLE/REPLY CODE(s) C19, C20 OR C32 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and CSKY)
IF STYLE/REPLY CODE(s) C21 OR C22 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and CSKY)
IF STYLE/REPLY CODE(s) C23, C24 OR C33 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAU)
IF STYLE/REPLY CODE(s) C25, C26, C27, C28, C29 OR C30 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAR)
IF STYLE/REPLY CODE(s) C34, C41 OR C45 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) C35, C36, C37, C38, C39, C40, C42, C43, C44, C46, C47, C49, C50, C51 OR C53 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAU)
IF STYLE/REPLY CODE(s) C31 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAR)
IF STYLE/REPLY CODE(s) C48, C54, C55, C56, C57, C58 OR C59 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAU and CSKY)
IF STYLE/REPLY CODE(s) C52 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAU and CSKY)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLC42)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10032 | C1 | Y STRAINER W/BLOW-OFF PLUG |
| BF10041 | C10 | DIVERTED FLOW BASKET STRAINER W/THREADED COVER |
| BF10042 | C11 | DIVERTED FLOW PLUG STRAINER W/ THREADER COVER |
| BF10043 | C12 | STEAM JACKETED DIVERTED FLOW BASKET STRAINER W/BOLTED COVER |
| BF10044 | C13 | OFFSET FLOW BASKET STRAINER W/ CLAMPED COVER |
| BF10045 | C14 | OFFSET FLOW BASKET STRAINER W/BOLTED COVER |
| BF10046 | C15 | STRAIGHT FLOW BASKET STRAINER W/ BOLTED COVER |
| BF10047 | C16 | STRAIGHT FLOW BASKET STRAINER W/BOLTED COVER |
| BF10048 | C17 | STRAIGHT FLOW BASKET STRAINER W/BOLTED COVER |
| BF10049 | C18 | STRAIGHT FLOW BASKET STRAINER W/CLAMPED COVER |
| BF10050 | C19 | TWIN STRAINER W/CLAMPED COVER |
| BF10033 | C2 | Y STRAINER W/BOLTED COVER |
| BF10051 | C20 | TWIN STRAINER W/BOLTED COVER |
| BF10052 | C21 | TWIN STRAINER W/CLAMPED COVER |
| BF10053 | C22 | TWIN STRAINER W/BOLTED COVER |
| BF10054 | C23 | TWIN STRAINER W/THREADED COVER |
| BF10055 | C24 | TWIN STRAINER W/BOLTED COVER |
| BF10056 | C25 | SUCTION TYPE ROUNDED END |
| BF10057 | C26 | SUCTION TYPE BLUNT END |
| BF10058 | C27 | INLINE (HYDRAULIC) |
| BF10059 | C28 | INLINE DISPOSAL W/THREADED CONNECTIONS AND VAPOR DIVERTER |
| BF10060 | C29 | INLINE DISPOSAL W/THREADED CONNECTIONS |
| BF10034 | C3 | Y STRAINER W/THREADED COVER |
| BF10061 | C30 | INLINE DISPOSABLE W/HOSE CONNECTIONS AND VAPOR DIVERTER |
| BF10062 | C31 | INLINE DISPOSABLE W/HOSE CONNECTIONS |
| BF10063 | C32 | TEE TYPE (HYDRAULIC) |
| BF10064 | C33 | ANGLE STRAINER W/THREADED COVER |
| BF10065 | C34 | HIGH PRESSURE ANGLE STRAINER W/BOLTED COVER |
| BF10066 | C35 | BOWL AND BAIL W/ VAPOR DIVERTER |
| BF10067 | C36 | BOWL AND BAIL |
| BF10068 | C37 | UNTHREADED SHELL |
| BF10069 | C38 | UNTHREADED BODY AND COVER ASSY |
| BF10070 | C39 | UNTHREADED BODY AND COVER ASSY (FILTER HEAD AT BOTTOM) |
| BF10035 | C4 | DIVERTED FLOW BASKET STRAINER W/BOLTED COVER |
| BF10071 | C40 | UNTHREADED SHELL |
| BF10072 | C41 | UNTHREADED SHELL W/SELECTIVE FLOW |
| BF10073 | C42 | THREADED SHELL (MASON JAR) |
| BF10074 | C43 | QUICK-DISCONNECT SHELL |
| BF10075 | C44 | HIGH PRESSURE THREADED BODY |
| BF10076 | C45 | HIGH PRESSURE BOLTED SHELL |
| BF10077 | C46 | BODY AND COVER ASSY (BOLTED FLANGE) |
| BF10078 | C47 | SPLIT BODY W/ PARTIAL FLOW OUTLET (LOOP OR RIM CLAMP) |
| BF10079 | C48 | SPLIT BODY (LOOP OR RIM CLAMP) |
| BF10080 | C49 | SPLIT BODY (LOOP OR RIM CLAMP) |
| BF10036 | C5 | DIVERTED FLOW BASKET STRAINER W/CLAMPED COVER |
| BF10081 | C50 | SPLIT BODY (LOOP OR RIM CLAMP) |
| BF10082 | C51 | ELL TYPE (HYDRAULIC) |
| BF10083 | C52 | LEG MOUNTED BODY AND COVER ASSY (SWING BOLTED) |
| BF10084 | C53 | LEG MOUNTED BODY AND COVER ASSY (SWING BOLTED) |
| BF10085 | C54 | LEG MOUNTED SPLIT BODY (LOOP OR RIM CLAMP) |
| BF10087 | C55 | LEG MOUNTED BODY AND COVER (SWING BOLTED) |
| BF10086 | C56 | LEG MOUNTED BODY AND COVER ASSY (SWING BOLTED) |
| BF10088 | C57 | LEG MOUNTED BODY AND COVER ASSY (BOLTED FLANGE) |
| BF10089 | C58 | FLOOR MOUNTED SPLIT BODY (BOLTED FLANGE) |
| BF10090 | C59 | FLOOR MOUNTED SPLIT BODY (LOOP OR RIM CLAMP) |
| BF10037 | C6 | DIVERTED FLOW BASKET STRAINER W/BOLTED COVER |
| BF10038 | C7 | DIVERTED FLOW BASKET STRAINER W/CLAMPED COVER |
| BF10039 | C8 | DIVERTED FLOW BASKET STRAINER W/BOLTED COVER |
| BF10040 | C9 | DIVERTED FLOW BASKET STRAINER W/THREADED COVER |
AAZL*JTAPERED HOLE MINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZLJAC2.0*;AAZLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAA2.0*;ABPMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAS*JBODY INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADASJAC2.0*;ADASJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADMF*JMOUNTING FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADMFJAC2.0*;ADMFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADMM*JMOUNTING FLANGE BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADMMJAB2.0*;ADMMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADMN*JMOUNTING FLANGE BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADMNJAA2.0*;ADMNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADMT*JTAPERED HOLE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADMTJAA2.0*;ADMTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNB*JSPOOL LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNBJAA2.0*;ADNBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPR*JBODY THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPRJAA2.0*;ADPRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGWL*JSMALLEST OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST DIAMETER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGWLJAA2.0*;AGWLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGWM*JLARGEST OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIAMETER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGWMJAC2.0*;AGWMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APTE*JMOUNTING FLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APTEJAA2.0*;APTEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZTL*JBODY OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BODY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AZTLJAA2.0*;AZTLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BJMG*JOVERALL INSIDE LENGTH
THE INSIDE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BJMGJAA2.0*;BJMGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BJMH*JOVERALL INSIDE WIDTH
AN OVERALL INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BJMHJAB2.0*;BJMHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSKX*JBODY OVERALL DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSKXJAB2.0*;CSKXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAA2.0*;ADAQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAB2.0*;ADARJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAA2.0*;ADATJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAB2.0*;ADAUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSKY*JDISTANCE FROM BOTTOM OF BODY TO CENTER OF INLET
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSKYJAC2.0*;CSKYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSLQ*JCENTER TO CENTER DISTANCE BETWEEN CONNECTIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSLQJAC2.0*;CSLQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSMD*JANGLE BETWEEN CONNECTIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSMDJRA2.0*;CSMDJRA2.0$$JRA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADML*AMOUNTING FLANGE BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES IN THE MOUNTING FLANGE.
Enter the numeric reply with a minimum of one digit.
(ADMLA10*)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQQR)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDBF)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACLLDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AATDST0166*;MATT3AATDST0166$DFBD000*;MATT3AATDST0166$$DFBD000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3CKW | CONTAINER/CARTRIDGE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALD000 | ALUMINA |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL2117 | ALUMINUM ALLOY 2117 |
| AL2219 | ALUMINUM ALLOY 2219 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL3004 | ALUMINUM ALLOY 3004 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL5005 | ALUMINUM ALLOY 5005 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5056 | ALUMINUM ALLOY 5056 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL5456 | ALUMINUM ALLOY 5456 |
| AL6053 | ALUMINUM ALLOY 6053 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| AL0028 | ALUMINUM ALLOY A380.0 |
| AL0060 | ALUMINUM ALLOY C355.0 |
| ASA000 | ASBESTOS |
| MSD000 | ASPHALT |
| CNA000 | CARBON |
| CNC000 | CARBON ACTIVATED |
| PPC000 | CARDBOARD |
| CSA000 | CELLULOSE |
| CSB000 | CELLULOSE ACETATE |
| CXB000 | CEMENT PORTLAND |
| CLD000 | CERAMIC |
| MSL000 | CHARCOAL |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU1016 | COPPER ALLOY 2.1030 |
| CU1039 | COPPER ALLOY 2.1050.01 |
| CU1040 | COPPER ALLOY 2.1052.01 |
| CU0264 | COPPER ALLOY 220 |
| CU0074 | COPPER ALLOY 230 |
| CU0076 | COPPER ALLOY 240 |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU0103 | COPPER ALLOY 510 |
| CU0624 | COPPER ALLOY 624 |
| CU0148 | COPPER ALLOY 745 |
| CU0150 | COPPER ALLOY 752 |
| CU0152 | COPPER ALLOY 764 |
| CU0157 | COPPER ALLOY 770 |
| CU0172 | COPPER ALLOY 836 |
| CU0202 | COPPER ALLOY 922 |
| CKA000 | CORK |
| CCA000 | COTTON |
| CCB000 | COTTON DUCK |
| MSP000 | DIATOMACEOUS EARTH |
| FBX000 | FELT |
| FBA000 | FIBER |
| FBS000 | FIBER SYNTHETIC |
| WDA000 | FIBERBOARD |
| MSQ000 | FULLERS EARTH |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| MTE000 | GUNMETAL |
| HRE000 | HAIR |
| FBL000 | HEMP |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| FBK000 | JUTE |
| LRA000 | LEATHER |
| LRK000 | LEATHER SHEEPSKIN |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| MTC000 | METAL |
| MTJ000 | METAL NONFERROUS/D |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| NL0019 | NICKEL ALLOY 502 |
| NL0018 | NICKEL ALLOY K-500 |
| NL0017 | NICKEL ALLOY R-405 |
| FBB000 | NYLON (USE PCP000) |
| PPA000 | PAPER |
| PPJ000 | PAPERBOARD (USE MRC ASWC OR CBJL) |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCD000 | PLASTIC ACRYLIC |
| PCAX00 | PLASTIC ACRYLONITRILE |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCAN00 | PLASTIC CELLULOSE ACETATE |
| PCH000 | PLASTIC EPOXY |
| PCJ000 | PLASTIC MELAMINE |
| PCCB00 | PLASTIC NYLON |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE (PET) |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCBC00 | PLASTIC STYRENE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PCAAX0 | PLASTIC UREA-FORMALDEHYDE |
| PCBA00 | PLASTIC URETHANE |
| PCAQ00 | PLASTIC VINYL CHLORIDE-ACETATE (USE PCAAA0 & PCBD00) |
| PTA000 | PLATINUM |
| WDB000 | PLYWOOD |
| FBC000 | POLYESTER |
| PMB000 | PULP, WOOD |
| FBD000 | RAYON |
| RSC000 | RESIN NATURAL |
| RSA000 | RESIN SYNTHETIC |
| MSZ000 | ROCK WOOL |
| RCE000 | RUBBER |
| RCF000 | RUBBER BUNA N |
| RCD000 | RUBBER CHLOROPRENE |
| RCA000 | RUBBER NATURAL |
| RCC000 | RUBBER SILICONE |
| RCB000 | RUBBER SYNTHETIC |
| MST000 | SAND |
| AGA000 | SILVER |
| MSG000 | SPONGE |
| STA000 | STEEL |
| ST0359 | STEEL COMP 1.0120 |
| ST0368 | STEEL COMP 1.0161 |
| ST0822 | STEEL COMP 1.4301 |
| ST1730 | STEEL COMP 1.4302 |
| ST0379 | STEEL COMP 1.4305 |
| ST0824 | STEEL COMP 1.4401 |
| ST2072 | STEEL COMP 1.4404 |
| ST0805 | STEEL COMP 1.4571 |
| ST1005 | STEEL COMP 1005 |
| ST1006 | STEEL COMP 1006 |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1025 | STEEL COMP 1025 |
| ST1030 | STEEL COMP 1030 |
| ST1035 | STEEL COMP 1035 |
| ST0202 | STEEL COMP 202 |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0180 | STEEL COMP 302B |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0077 | STEEL COMP 303F |
| ST0078 | STEEL COMP 303S |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0152 | STEEL COMP 308 |
| ST0309 | STEEL COMP 309 |
| ST0153 | STEEL COMP 309S |
| ST0310 | STEEL COMP 310 |
| ST0154 | STEEL COMP 310S |
| ST0155 | STEEL COMP 314 |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0323 | STEEL COMP 323 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST0348 | STEEL COMP 348 |
| ST0384 | STEEL COMP 384 |
| ST0385 | STEEL COMP 385 |
| ST0403 | STEEL COMP 403 |
| ST0405 | STEEL COMP 405 |
| ST0410 | STEEL COMP 410 |
| ST0414 | STEEL COMP 414 |
| ST0098 | STEEL COMP 416F |
| ST0420 | STEEL COMP 420 |
| ST0429 | STEEL COMP 429 |
| ST0430 | STEEL COMP 430 |
| ST0105 | STEEL COMP 440A |
| ST0106 | STEEL COMP 440B |
| ST0107 | STEEL COMP 440C |
| ST0108 | STEEL COMP 440F |
| ST0446 | STEEL COMP 446 |
| ST0631 | STEEL COMP 631 |
| STB000 | STEEL CORROSION RESISTING |
| SNB000 | TIN |
| WDC000 | WOOD |
| WLA000 | WOOL |
| WL0018 | WOOL COMP 16R1 |
| WL0001 | WOOL COMP F1 |
| WL0004 | WOOL COMP F12 |
| WL0009 | WOOL COMP F5 |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDXXB000*;SFTT3AEEDXXB000$DPNA000*;SFTT3AEEDXXB000$$DPNA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CKW | CONTAINER/CARTRIDGE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ANA000 | ANODIZE |
| A | ANY ACCEPTABLE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| ENA000 | ENAMEL |
| IRA000 | IRIDIUM |
| LQA000 | LACQUER |
| PBA000 | LEAD |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCB000 | PLASTIC POLYTETRAFLUOROETHYLENE |
| AGA000 | SILVER |
| SNA000 | TIN |
| ZNA000 | ZINC |
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC CRXW, YOU MUST ANSWER MRC (AKSX and AGCW)
IF STYLE/REPLY CODE(s) AT WERE ENTERED FOR MRC CRXW, YOU MUST ANSWER MRC (AKSV and AKSW)
CRXW*DFILTERING MEDIA DESIGN
AN INDICATION OF THE STRUCTURE OR CHARACTERISTIC OF THE FILTERING MEDIA.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CRXW3CLDDCN*;CRXW3CLDDCN$DCP*;CRXW3CLDDCN$$DCP*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CLD | SINGLE FILTERING MEDIA RESPONSE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC48) | Reply |
| DN | AIR SOCK |
| BJ | BAG |
| AC | BELLOWS |
| AB | BLOCK |
| AH | CELLULAR |
| DP | CONVOLUTED |
| CN | CORE |
| AJ | CORRUGATED |
| CP | CRIMPED |
| DQ | ENCASED |
| CL | EXPANDED |
| CM | FLOCKED |
| DW | GRANULE |
| BG | HONEYCOMB |
| AL | KNITTED |
| AN | LAMINATED |
| CK | LAYERED |
| AP | LOOSE PACKED |
| CJ | MATTED |
| AQ | MESH |
| AR | MOLDED |
| AS | MULTIPLE STACKED DISKS |
| DG | PELLET |
| AT | PERFORATED |
| AU | PLEATED |
| DJ | POROUS |
| AW | RADIAL FINNED |
| AX | ROLL TYPE |
| DR | SHEETING |
| CQ | SHREDDED |
| AY | SINGLE STACKED DISKS |
| BX | SINGLE STAMPED DISK |
| AZ | SINTERED |
| CR | SLIT |
| BA | SPIRAL WOUND |
| DS | SPUN |
| BB | SPUN ROVING |
| DT | V-SLOTS |
| BD | WOVEN |
AKSX*BMESH SIZE
A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF OPENINGS PER LINEAL INCH.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AKSXB2.0*;AKSXB2.0$$BM2.0*)
AGCW*JWIRE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGCWJAB2.0*;AGCWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKSV*JPERFORATION DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPENING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKSVJAA2.0*;AKSVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKSW*JPERFORATION QUANTITY
A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF PERFORATIONS CONTAINED IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKSWJA2.0*)
| Table 1 |
| Reply Code (AB39) | Reply |
| A | PER SQUARE INCH |
| H | PER SQUARE MILLIMETER |
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDFKY)
| Table 1 |
| Reply Code (AK54) | Reply |
| FKY | LIMITED |
| FKZ | NONREUSABLE |
| FLA | REUSABLE |
CCZMAFILTERING ELEMENT QUANTITY
THE NUMBER OF FILTERING ELEMENTS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(CCZMA10*)
ADNHJFILTRATION RATING IN MICRONS
THE SIZE OF THE SMALLEST PARTICLE WHICH THE ELEMENT IS CAPABLE OF REMOVING FROM THE FLUID WHICH PASSES THROUGH THE FILTERING MATERIAL.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNHJG2.0*;ADNHJG2.0$$JG2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| G | ABSOLUTE |
MEDA*DMEDIA FOR WHICH DESIGNED
THE TYPE OF MEDIA FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(MEDADAAE*;MEDADAKA$DABJ*;MEDADAKA$$DABJ*)
| Table 1 |
| Reply Code (AN91) | Reply |
| AAE | AIR |
| A | ANY ACCEPTABLE |
| AJU | BLOOD |
| AKA | ETHYLENE |
| AAY | FUEL/OIL, HYDROCARBON |
| AAQ | GAS |
| AFA | LIQUID DRUGS |
| AFC | LIQUID FOOD |
| ABB | LIQUID, INGESTED |
| ABE | NITROGEN, GASEOUS |
| ABF | NITROGEN, LIQUID |
| ABJ | OXYGEN, GASEOUS |
| ABK | OXYGEN, LIQUID |
| AFD | REFRIGERANT |
| AFE | REFRIGERANT 114 |
| ABR | WATER |
| ADM | WATER, DEMINERALIZED |
| AEK | WATER/ALCOHOL MIXTURE |
CQGMJMAXIMUM OPERATING PRESSURE
THE MAXIMUM PRESSURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQGMJK2.0*)
| Table 1 |
| Reply Code (AN71) | Reply |
| B | BAR |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| L | KILOPASCALS |
| N | NEWTONS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
AZKQ*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Tables 1 and 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples. For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.
(AZKQJFA68.0*; AZKQJCB0.0$$JCC35.0*; AZKQJFCM15.0*; AZKQJFBM40.0$$JFC75.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNPJDROP PRESSURE
THE AMOUNT OF PRESSURE LOSS IN THE SYSTEM,DUE TO THE RESISTANCE OF FLOW THROUGH THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNPJF2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| F | BAR |
| L | KILOPASCALS |
| V | POUNDS PER SQUARE INCH |
ADNQJDIFFERENTIAL PRESSURE
THE DIFFERENCE IN OPPOSING PRESSURE WHICH AN ITEM IS CAPABLE OF WITHSTANDING WITHOUT EVIDENCE OF DEFORMATION OR OTHER DAMAGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNQJL2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| F | BAR |
| L | KILOPASCALS |
| V | POUNDS PER SQUARE INCH |
IF STYLE/REPLY CODE(s) AD, AN, AS OR NR WERE ENTERED FOR MRC CRXZ, YOU MUST ANSWER MRC (CSLY)
IF STYLE/REPLY CODE(s) AB, MR OR NS WERE ENTERED FOR MRC CRXZ, YOU MUST ANSWER MRC (CSPN)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC CRXZ, YOU MUST ANSWER MRC (CSTD and CTBJ)
IF STYLE/REPLY CODE(s) AA, AC, AE OR AG WERE ENTERED FOR MRC CRXZ, YOU MUST ANSWER MRC (CTDY)
CRXZ*DFIRST INTAKE CONNECTION TYPE
INDICATES THE TYPE OF CONNECTION ON THE FIRST INTAKE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CRXZ3ABJDAM*;CRXZ3ABJDAM$DNR*;CRXZ3ABJDAM$$DNR*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABJ | SIDE |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB76) | Reply |
| AN | BUTT WELD |
| NR | EXTERNAL BUTT WELD |
| NS | INTERNAL SOLDER |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| MR | SOCKET WELDING |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| AS | UNTHREADED EXTERNAL HOSE |
| AD | UNTHREADED EXTERNAL TUBE |
| AB | UNTHREADED INTERNAL TUBE |
CSLY*JFIRST INTAKE NOMINAL OUTSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSLYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CSPN*JFIRST INTAKE NOMINAL INSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSPNJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) 1, 5, 6, 7, 11 OR 12 WERE ENTERED FOR MRC CSTD, YOU MUST ANSWER MRC (CTHJ and CTMP and CTRZ)
IF STYLE/REPLY CODE(s) 2 OR 8 WERE ENTERED FOR MRC CSTD, YOU MUST ANSWER MRC (CSRH and CTHJ)
IF STYLE/REPLY CODE(s) 3, 4, 9 OR 10 WERE ENTERED FOR MRC CSTD, YOU MUST ANSWER MRC (CTHJ)
CSTD*LFIRST INTAKE FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CSTDL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10157 | 1 | RECTANGULAR W/UNTHREADED BOLT HOLES |
| BF10166 | 10 | HEXAGON W/THREADED BOLT HOLES |
| BF10167 | 11 | OVAL W/THREADED BOLT HOLES |
| BF10168 | 12 | TRIANGULAR W/THREADED BOLT HOLES |
| BF10158 | 2 | ROUND W/UNTHREADED BOLT HOLES |
| BF10159 | 3 | OCTAGON W/UNTHREADED BOLT HOLES |
| BF10160 | 4 | HEXAGON W/UNTHREADED BOLT HOLES |
| BF10161 | 5 | OVAL W/UNTHREADED BOLT HOLES |
| BF10162 | 6 | TRIANGULAR W/UNTHREADED BOLT HOLES |
| BF10163 | 7 | RECTANGULAR W/THREADED BOLT HOLES |
| BF10164 | 8 | ROUND W/THREADED BOLT HOLES |
| BF10165 | 9 | OCTAGON W/THREADED BOLT HOLES |
CSRH*JFIRST INTAKE FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSRHJAC2.0*;CSRHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTHJ*JFIRST INTAKE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTHJJAA2.0*;CTHJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTMP*JFIRST INTAKE FLANGE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTMPJAB2.0*;CTMPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTRZ*JFIRST INTAKE FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTRZJAA2.0*;CTRZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 4, 5, 6, 7 OR 8 WERE ENTERED FOR MRC CTBJ, YOU MUST ANSWER MRC (CWFT and CWMF)
IF STYLE/REPLY CODE(s) 9, 10 OR 11 WERE ENTERED FOR MRC CTBJ, YOU MUST ANSWER MRC (CXBM and CXNQ)
CTBJ*LFIRST INTAKE FLANGE FACE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CTBJL6)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10169 | 1 | PLAIN |
| BF10178 | 10 | RECESSED |
| BF10179 | 11 | RECESSED W/GASKET GROOVE |
| BF10170 | 2 | PLAIN SWIVEL |
| BF10171 | 3 | PLAIN SWIVEL W/GASKET GROOVE |
| BF10172 | 4 | RAISED |
| BF10173 | 5 | RAISED |
| BF10174 | 6 | RAISED |
| BF10175 | 7 | SWIVEL RAISED |
| BF10176 | 8 | RAISED SWIVEL W/GASKET GROOVE |
| BF10177 | 9 | RECESSED |
CWFT*JFIRST INTAKE FLANGE RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWFTJAC2.0*;CWFTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWMF*JFIRST INTAKE FLANGE RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWMFJAB2.0*;CWMFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXBM*JFIRST INTAKE FLANGE RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXBMJAB2.0*;CXBMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXNQ*JFIRST INTAKE FLANGE RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNQJAB2.0*;CXNQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) NC, NE, NF, JC, JE, JF OR AM WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWNZ and CXPF)
IF STYLE/REPLY CODE(s) BA, SF, SL, NP, NT, AN, NG, PM OR PS WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CXPF)
IF STYLE/REPLY CODE(s) BF, BR, BS OR BW WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWAR and CXPF)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWDJ and CXPF) or (CTGK and CXCC and CXPF) or (CTGK and CXPF)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWAR and CWNZ and CXPF)
IF STYLE/REPLY CODE(s) NS OR JS WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWAR and CWNZ and CXPF) or (CTGK and CWAR and CXPF)
IF STYLE/REPLY CODE(s) BL OR BN WERE ENTERED FOR MRC CTDY, YOU MUST ANSWER MRC (CTGK and CWAR and CXPF)
CTDY*DFIRST INTAKE THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATION FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CTDYDNP)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CTGK*JFIRST INTAKE NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTGKJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CWAR*AFIRST INTAKE THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CWARAV8)
CWDJ*BFIRST INTAKE THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CWDJB2.0)
CWNZ*AFIRST INTAKE THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(CWNZAA2)
CXCC*JFIRST INTAKE THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CXCCJNTE2.0*;CXCCJNTE2.0$$JNTE2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CXPF*DFIRST INTAKE THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CXPFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CRZD*DSECOND INTAKE CONNECTION RELATIONSHIP TO FIRST INTAKE CONNECTION
THE SECOND INTAKE CONNECTION RELATIONSHIP TO THE FIRST INTAKE CONNECTION.
Enter the applicable reply code from the table below
(CRZDDB)
| Table 1 |
| Reply Code (AB78) | Reply |
| B | IDENTICAL |
| F | NOT IDENTICAL |
CSNT*JSECOND INTAKE NOMINAL OUTSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSNTJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CSSG*JSECOND INTAKE NOMINAL INSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSSGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) 1, 5, 6, 7, 11 OR 12 WERE ENTERED FOR MRC CSXM, YOU MUST ANSWER MRC (CTJR and CTNS and CTWG)
IF STYLE/REPLY CODE(s) 2 OR 8 WERE ENTERED FOR MRC CSXM, YOU MUST ANSWER MRC (CSQP and CTJR)
IF STYLE/REPLY CODE(s) 3, 4, 9 OR 10 WERE ENTERED FOR MRC CSXM, YOU MUST ANSWER MRC (CTJR)
CSXM*LSECOND INTAKE FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CSXML5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10157 | 1 | RECTANGULAR W/UNTHREADED BOLT HOLES |
| BF10166 | 10 | HEXAGON W/THREADED BOLT HOLES |
| BF10167 | 11 | OVAL W/THREADED BOLT HOLES |
| BF10168 | 12 | TRIANGULAR W/THREADED BOLT HOLES |
| BF10158 | 2 | ROUND W/UNTHREADED BOLT HOLES |
| BF10159 | 3 | OCTAGON W/UNTHREADED BOLT HOLES |
| BF10160 | 4 | HEXAGON W/UNTHREADED BOLT HOLES |
| BF10161 | 5 | OVAL W/UNTHREADED BOLT HOLES |
| BF10162 | 6 | TRIANGULAR W/UNTHREADED BOLT HOLES |
| BF10163 | 7 | RECTANGULAR W/THREADED BOLT HOLES |
| BF10164 | 8 | ROUND W/THREADED BOLT HOLES |
| BF10165 | 9 | OCTAGON W/THREADED BOLT HOLES |
CSQP*JSECOND INTAKE FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSQPJAC2.0*;CSQPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTJR*JSECOND INTAKE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJRJAA2.0*;CTJRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTNS*JSECOND INTAKE FLANGE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTNSJAA2.0*;CTNSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTWG*JSECOND INTAKE FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTWGJAB2.0*;CTWGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTCZ*LSECOND INTAKE FLANGE FACE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CTCZL2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10169 | 1 | PLAIN |
| BF10178 | 10 | RECESSED |
| BF10179 | 11 | RECESSED W/GASKET GROOVE |
| BF10170 | 2 | PLAIN SWIVEL |
| BF10171 | 3 | PLAIN SWIVEL W/GASKET GROOVE |
| BF10172 | 4 | RAISED |
| BF10173 | 5 | RAISED |
| BF10174 | 6 | RAISED |
| BF10175 | 7 | SWIVEL RAISED |
| BF10176 | 8 | RAISED SWIVEL W/GASKET GROOVE |
| BF10177 | 9 | RECESSED |
IF STYLE/REPLY CODE(s) NC, NE, NF, JC, JE, JF OR AM WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CWSX and CXRS)
IF STYLE/REPLY CODE(s) BA, SF, SL, NP, NT, AN, NG, PM OR PS WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CXRS)
IF STYLE/REPLY CODE(s) BF, BR, BS OR BW WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CWBT and CXRS)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CXRS) or (CTMC and CXRS) or (CTMC and CXRS)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CWBT and CWSX and CXRS)
IF STYLE/REPLY CODE(s) NS OR JS WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CWBT and CWSX and CXRS) or (CTMC and CWBT and CXRS)
IF STYLE/REPLY CODE(s) BL OR BN WERE ENTERED FOR MRC CTFN, YOU MUST ANSWER MRC (CTMC and CWBT and CXRS)
CTFN*DSECOND INTAKE THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CTFNDNF)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CTMC*JSECOND INTAKE NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTMCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CWBT*ASECOND INTAKE THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CWBTAM4)
CWSX*ASECOND INTAKE THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(CWSXAO0)
CXRS*DSECOND INTAKE THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CXRSDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CSJRDFIRST DISCHARGE CONNECTION RELATIONSHIP TO INTAKE CONNECTION
INDICATES THE FIRST DISCHARGE CONNECTION RELATIONSHIP TO AN INTAKE CONNECTION.
Enter the applicable reply code from the table below
(CSJRDN)
| Table 1 |
| Reply Code (AB78) | Reply |
| N | IDENTICAL TO FIRST INTAKE CONNECTION |
| P | IDENTICAL TO SECOND INTAKE CONNECTION |
| F | NOT IDENTICAL |
CSMP*JFIRST DISCHARGE NOMINAL OUTSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSMPJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CSQB*JFIRST DISCHARGE NOMINAL INSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSQBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) 1, 5, 6, 7, 11 OR 12 WERE ENTERED FOR MRC CSWC, YOU MUST ANSWER MRC (CTKC and CTND and CTSL)
IF STYLE/REPLY CODE(s) 2 OR 8 WERE ENTERED FOR MRC CSWC, YOU MUST ANSWER MRC (CSYK and CTKC)
IF STYLE/REPLY CODE(s) 3, 4, 9 OR 10 WERE ENTERED FOR MRC CSWC, YOU MUST ANSWER MRC (CTKC)
CSWC*LFIRST DISCHARGE FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATION THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CSWCL3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10157 | 1 | RECTANGULAR W/UNTHREADED BOLT HOLES |
| BF10166 | 10 | HEXAGON W/THREADED BOLT HOLES |
| BF10167 | 11 | OVAL W/THREADED BOLT HOLES |
| BF10168 | 12 | TRIANGULAR W/THREADED BOLT HOLES |
| BF10158 | 2 | ROUND W/UNTHREADED BOLT HOLES |
| BF10159 | 3 | OCTAGON W/UNTHREADED BOLT HOLES |
| BF10160 | 4 | HEXAGON W/UNTHREADED BOLT HOLES |
| BF10161 | 5 | OVAL W/UNTHREADED BOLT HOLES |
| BF10162 | 6 | TRIANGULAR W/UNTHREADED BOLT HOLES |
| BF10163 | 7 | RECTANGULAR W/THREADED BOLT HOLES |
| BF10164 | 8 | ROUND W/THREADED BOLT HOLES |
| BF10165 | 9 | OCTAGON W/THREADED BOLT HOLES |
CSYK*JFIRST DISCHARGE FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYKJAC2.0*;CSYKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTKC*JFIRST DISCHARGE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTKCJAA2.0*;CTKCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTND*JFIRST DISCHARGE FLANGE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTNDJAB2.0*;CTNDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTSL*JFIRST DISCHARGE FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTSLJAA2.0*;CTSLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 4, 5, 6, 7 OR 8 WERE ENTERED FOR MRC CTCS, YOU MUST ANSWER MRC (CWGG and CWQK)
IF STYLE/REPLY CODE(s) 9, 10 OR 11 WERE ENTERED FOR MRC CTCS, YOU MUST ANSWER MRC (CXDN and CXSR)
CTCS*LFIRST DISCHARGE FLANGE FACE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CTCSL5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10169 | 1 | PLAIN |
| BF10178 | 10 | RECESSED |
| BF10179 | 11 | RECESSED W/GASKET GROOVE |
| BF10170 | 2 | PLAIN SWIVEL |
| BF10171 | 3 | PLAIN SWIVEL W/GASKET GROOVE |
| BF10172 | 4 | RAISED |
| BF10173 | 5 | RAISED |
| BF10174 | 6 | RAISED |
| BF10175 | 7 | SWIVEL RAISED |
| BF10176 | 8 | RAISED SWIVEL W/GASKET GROOVE |
| BF10177 | 9 | RECESSED |
CWGG*JFIRST DISCHARGE FLANGE RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWGGJAC2.0*;CWGGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWQK*JFIRST DISCHARGE FLANGE RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWQKJAB2.0*;CWQKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXDN*JFIRST DISCHARGE FLANGE RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXDNJAB2.0*;CXDNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXSR*JFIRST DISCHARGE FLANGE RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXSRJAA2.0*;CXSRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) NC, NE, NF, JC, JE, JF OR AM WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWRH and CXYG)
IF STYLE/REPLY CODE(s) BA, SF, SL, NP, NT, AN, NG, PM OR PS WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CXYG)
IF STYLE/REPLY CODE(s) BF, BR, BS OR BW WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWBB and CXYG)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWKQ and CXYG) or (CTLG and CXYG) or (CTLG and CXYG)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWBB and CWRH and CXYG)
IF STYLE/REPLY CODE(s) NS OR JS WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWBB and CWRH and CXYG) or (CTLG and CWBB and CXYG)
IF STYLE/REPLY CODE(s) BL OR BN WERE ENTERED FOR MRC CTFF, YOU MUST ANSWER MRC (CTLG and CWBB and CXYG)
CTFF*DFIRST DISCHARGE THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CTFFDBA)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CTLG*JFIRST DISCHARGE NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTLGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CWBB*AFIRST DISCHARGE THREAD QUANTITY PER INCH
THE NUMBER OF THREADS OF THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CWBBAM5)
CWKQ*BFIRST DISCHARGE THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CWKQB2.0)
CWRH*AFIRST DISCHARGE THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(CWRHAN5)
CXYG*DFIRST DISCHARGE THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CXYGDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CSLN*DSECOND DISCHARGE CONNECTION RELATIONSHIP TO PRECEDING CONNECTION
INDICATES THE SECOND DISCHARGE CONNECTION RELATIONSHIP TO THE PRECEDING CONNECTIONS.
Enter the applicable reply code from the table below
(CSLNDF)
| Table 1 |
| Reply Code (AB78) | Reply |
| Q | IDENTICAL TO FIRST DISCHARGE CONNECTION |
| N | IDENTICAL TO FIRST INTAKE CONNECTION |
| P | IDENTICAL TO SECOND INTAKE CONNECTION |
| F | NOT IDENTICAL |
CSRD*JSECOND DISCHARGE NOMINAL OUTSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSRDJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CSTH*JSECOND DISCHARGE NOMINAL INSIDE DIAMETER
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSTHJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) 1, 5, 6, 7, 11 OR 12 WERE ENTERED FOR MRC CSYY, YOU MUST ANSWER MRC (CTLP)
IF STYLE/REPLY CODE(s) 2 OR 8 WERE ENTERED FOR MRC CSYY, YOU MUST ANSWER MRC (CSZF and CTLP)
IF STYLE/REPLY CODE(s) 3, 4, 9 OR 10 WERE ENTERED FOR MRC CSYY, YOU MUST ANSWER MRC (CTLP)
CSYY*LSECOND DISCHARGE FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CSYYL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10157 | 1 | RECTANGULAR W/UNTHREADED BOLT HOLES |
| BF10166 | 10 | HEXAGON W/THREADED BOLT HOLES |
| BF10167 | 11 | OVAL W/THREADED BOLT HOLES |
| BF10168 | 12 | TRIANGULAR W/THREADED BOLT HOLES |
| BF10158 | 2 | ROUND W/UNTHREADED BOLT HOLES |
| BF10159 | 3 | OCTAGON W/UNTHREADED BOLT HOLES |
| BF10160 | 4 | HEXAGON W/UNTHREADED BOLT HOLES |
| BF10161 | 5 | OVAL W/UNTHREADED BOLT HOLES |
| BF10162 | 6 | TRIANGULAR W/UNTHREADED BOLT HOLES |
| BF10163 | 7 | RECTANGULAR W/THREADED BOLT HOLES |
| BF10164 | 8 | ROUND W/THREADED BOLT HOLES |
| BF10165 | 9 | OCTAGON W/THREADED BOLT HOLES |
CSZF*JSECOND DISCHARGE FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSZFJAB2.0*;CSZFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTLP*JSECOND DISCHARGE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTLPJAA2.0*;CTLPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTDK*LSECOND DISCHARGE FLANGE FACE STYLE
THE STYLE DESIGNATION INDICATION THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CTDKL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10169 | 1 | PLAIN |
| BF10178 | 10 | RECESSED |
| BF10179 | 11 | RECESSED W/GASKET GROOVE |
| BF10170 | 2 | PLAIN SWIVEL |
| BF10171 | 3 | PLAIN SWIVEL W/GASKET GROOVE |
| BF10172 | 4 | RAISED |
| BF10173 | 5 | RAISED |
| BF10174 | 6 | RAISED |
| BF10175 | 7 | SWIVEL RAISED |
| BF10176 | 8 | RAISED SWIVEL W/GASKET GROOVE |
| BF10177 | 9 | RECESSED |
IF STYLE/REPLY CODE(s) NC, NE, NF, JC, JE, JF OR AM WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CWYJ and CXTT)
IF STYLE/REPLY CODE(s) BA, SF, SL, NP, NT, AN, NG, PM OR PS WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CXTT)
IF STYLE/REPLY CODE(s) BF, BR, BS OR BW WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CWCP and CXTT)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CXTT) or (CTQF and CXTT) or (CTQF and CXTT)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CWCP and CWYJ and CXTT)
IF STYLE/REPLY CODE(s) NS OR JS WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CWCP and CWYJ and CXTT) or (CTQF and CWCP and CXTT)
IF STYLE/REPLY CODE(s) BL OR BN WERE ENTERED FOR MRC CTGB, YOU MUST ANSWER MRC (CTQF and CWCP and CXTT)
CTGB*DSECOND DISCHARGE THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CTGBDBL)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CTQF*JSECOND DISCHARGE NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTQFJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CWCP*ASECOND DISCHARGE THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CWCPAF7)
CWYJ*ASECOND DISCHARGE THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(CWYJAH7)
CXTT*DSECOND DISCHARGE THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CXTTDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
IF STYLE/REPLY CODE(s) AAD WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (CBQD)
IF STYLE/REPLY CODE(s) ACZ WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (CBQD and ABTJ and ABTB)
IF STYLE/REPLY CODE(s) ADA WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (CBQD and ABTJ and ABTB and CSJC)
IF STYLE/REPLY CODE(s) ADE WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (ABTJ and CDTD and CSJC)
IF STYLE/REPLY CODE(s) ADF WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (CDTD and CSJC)
IF STYLE/REPLY CODE(s) ADG WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (ABTJ and ABTB)
AAXXDMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AAXX3AEEDADF*;AAXX3AEEDADF$DADB*;AAXX3AEEDADF$$DADB*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABF | CENTER |
| 3AEE | OVERALL |
| 3CLK | BOTTOM SIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA78) | Reply |
| AAD | BRACKET |
| ACZ | BRACKET W/DRILLED HOLE |
| ADA | BRACKET W/THREADED HOLE |
| ADB | INLET CONNECTION |
| ADC | OUTLET CONNECTION |
| ADD | STRAP |
| ADE | THREADED HOLE |
| ADF | THREADED STUD |
| ADG | UNTHREADED HOLE |
CBQD*ABRACKET QUANTITY
THE NUMBER OF BRACKETS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(CBQDA10*)
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
AFQM*JDISTANCE BETWEEN MOUNTING HOLE CENTERS
THE DISTANCE BETWEEN THE CENTERLINE OF THE MOUNTING HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFQMJAC2.0*;AFQMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CTXF)
CDTD*DMOUNTING FACILITY THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A MOUNTING FACILITY DIAMETER.
Enter the applicable reply code from the table below
(CDTDDBF)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CSJC*JMOUNTING FACILITY NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE MOUNTING FACILITY THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSJCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CTXF*BMOUNTING FACILITY THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE MOUNTING FACILITY,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXFB2.0)
AKBN*DMOUNTING FACILITY THREAD DIRECTION
THE DIRECTION OF THE THREADS OF A MOUNTING FACILITY WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AKBNDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CXZXDFILTERING SYSTEM FOR WHICH DESIGNED
THE FILTERING SYSTEM FOR WHICH THE ITEM IS DESIGNED TO BE USED.
Enter the applicable reply code from the table below
(CXZXDAK*;CXZXDAH$DAL*)
| Table 1 |
| Reply Code (AL92) | Reply |
| AH | BY-PASS FLOW |
| AB | DUAL FLOW |
| AJ | FULL FLOW |
| AK | PARTIAL FLOW |
| AL | SHUNT FLOW |
BGSS*DROTATING DEVICE TYPE
INDICATES THE TYPE OF ROTATING DEVICE PROVIDED ON THE ITEM.
Enter the applicable reply code from the table below
(BGSSDGW)
| Table 1 |
| Reply Code (AC82) | Reply |
| GW | BLADE |
| FA | ELEMENT |
CCZQ*DROTATION METHOD
THE MEANS BY WHICH THE ITEM IS ROTATED.
Enter the applicable reply code from the table below
(CCZQDAAD)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAD | ELECTRIC MOTOR |
| ACF | HYDRAULIC MOTOR |
| AAF | MANUAL |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBQM*;CBBLDBLZ$$DBMC*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BLN | AIR BLEED VALVE |
| BLP | ANTIDRAIN BACK DEVICE |
| AKB | BY-PASS VALVE |
| BLQ | CASE SHUT-OFF VALVE |
| BLR | CLEANING BLADES |
| BLS | DIFFERENTIAL PRESSURE INDICATOR |
| BLT | DIFFERENTIAL PRESSURE RELIEF VALVE |
| BLW | DRAIN COCK |
| BLX | DRAIN PLUG |
| BLY | FLOW CONTROL VALVE |
| BQM | LIFTING BAIL |
| BLZ | MAGNET |
| BMA | MANUAL SHUT-OFF VALVE |
| BMB | SWITCH-OVER VALVE |
| BMC | THERMAL LOCKOUT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCD2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CD | CUBIC DECIMETERS |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAJ*;BBRGDAN$DAD*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAD*;BBRJDAQ$$DAE*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AD | FLAMMABLE |
| AE | FRAGILE |
| AK | MAGNETIC |
| AQ | PILFERABLE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPTA000*;PRMTDAGA000$DPDA000*;PRMTDAGA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000F2.0*;PMWTJRHA000F2.0$$JRHA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ157*;HZRDDHAZ012$$DHAZ007*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ007 | ASPHALT |
| HAZ157 | CHARCOAL |
| HAZ012 | COPPER |
| HAZ092 | MAGNESIUM |
| HAZ252 | NICKEL |
| HAZ285 | PLASTIC |
| HAZ286 | PLATINUM |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information