A handheld power tool with two settings; one high rpm setting for drilling and one low rpm, high torque setting for installing fasteners, may be cordless.May include features such as a keyed or keyless type chuck, variable speed trigger, battery packs and charger (for cordless type).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED66603*)
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (ACZB and FAAZ)
ACDCDCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDB*;ACDCDC$DB*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
AKUP*JNOMINAL CHUCK SIZE
A NOMINAL MEASUREMENT OF THE SIZE OF THE CHUCK.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKUPJL2.0*;AKUPJL2.0$$JL2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AMSEJVOLTAGE RATING
THE VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMSEJKC2.0*;AMSEJKC2.0$$JKC2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACZB*JFREQUENCY RATING
THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACZBJKC2.0*;ACZBJKC2.0$JKC2.0*;ACZBJKC2.0$$JKC2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| E | HERTZ |
| K | KILOHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDB$DC*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
ACUS*BALTERNATING CURRENT RATING IN AMPS
THE ALTERNATING CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACUSB2.0)
ACUT*BDIRECT CURRENT RATING IN AMPS
THE DIRECT CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACUTB2.0*;ACUTB2.0$$BM2.0*)
BRZTJNO LOAD SPEED IN RPM
THE SPEED AT WHICH AN ITEM CAN BE OPERATED UNDER A NO LOAD CONDITION,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRZTJC2.0*;BRZTJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AAB WERE ENTERED FOR MRC BRZX, YOU MUST ANSWER MRC (CTKZ)
BRZXDDRIVE FOR WHICH DESIGNED
AN INDICATION OF THE DRIVE FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BRZXDAAC)
| Table 1 |
| Reply Code (AN40) | Reply |
| AAB | ANGULAR |
| AAC | STRAIGHT |
BRZRDDRIVE END TYPE
INDICATES THE TYPE OF DRIVE END PROVIDED.
Enter the applicable reply code from the table below
(BRZRDADS*;BRZRDALJ$DACS*)
| Table 1 |
| Reply Code (AK84) | Reply |
| ACR | COLLET CHUCK |
| ADS | EXTERNAL |
| ALJ | FEMALE SPINDLE |
| ADT | INTERNAL |
| ACS | KEYED JAW CHUCK |
| ACT | KEYLESS JAW CHUCK |
| ACW | MALE SPINDLE |
| ACX | MORSE TAPER SOCKET |
| ACY | SOCKET CHUCK |
CTKZ*JANGLE
THE ANGLE BETWEEN DESIGNATED POINTS ON AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTKZJD2.0*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
BRZZDPLUG CONNECTOR TYPE
INDICATES THE TYPE OF PLUG CONNECTOR PROVIDED.
Enter the applicable reply code from the table below
(BRZZDAL*;BRZZDAM$DAQ*)
| Table 1 |
| Reply Code (AK12) | Reply |
| AL | 2-PRONG |
| AM | 3-PRONG |
| AQ | 4-PRONG |
ABBBDSPEED ADJUSTMENTS
THE DIFFERENT SPEEDS AT WHICH THE ITEM MAY BE OPERATED.
Enter the applicable reply code from the table below
(ABBBDQ*;ABBBDB$$DB*)
| Table 1 |
| Reply Code (AB03) | Reply |
| B | TWO SPEED |
| Q | VARIABLE SPEED |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJCG*JTORQUE CAPACITY
AN INDICATION OF THE UNIT OF MEASURE AND THE NUMERIC TORQUE LIMIT FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJCGJKB2.0*;AJCGJKB2.0$$JKB2.1*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| K | CENTIMETER-KILOGRAMS |
| F | FOOT-POUNDS |
| R | INCH-GRAMS |
| A | INCH-OUNCES |
| G | INCH-POUNDS |
| S | METER-KILOGRAMS |
| N | METER-NEWTON |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJRU*ACLUTCH SETTING QUANTITY
THE NUMERIC QUANTITY FOR WHICH THE ITEM IS DESIGNED.
Enter the numeric reply with a minimum of one digit.
(AJRUA10*)
BQMM*JCORD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A CORD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQMMJFA2.0*;BQMMJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALMPLHANDLE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HANDLE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ALMPLAR1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AH10037 | AR1 | CLOSED END HANDLE |
| AH10038 | AR2 | PISTOL GRIP HANDLE |
| AH10039 | AR3 | COMBINATION BREASTPLATE AND SPADE END HANDLE REMOVABLE TYPE |
| AH10040 | AR4 | COMBINATION BREASTPLATE AND SPADE END HANDLE NON-REMOVABLE VERTICAL TYPE AND SIDE HANDLE |
| AH10041 | AR5 | COMBINATION BREASTPLATE AND SPADE END HANDLE NON-REMOVABLE HORIZONTAL TYPE AND SIDE HANDLE |
| DQ01209 | AR6 | BODYGRIP |
AMRNJSIZE DESIGNATOR
A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMRNJAC2.0*;AMRNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BSJN*DSTAND TYPE
INDICATES THE TYPE OF STAND PROVIDED.
Enter the applicable reply code from the table below
(BSJNDASD*;BSJNDASP$DASD*)
| Table 1 |
| Reply Code (AK54) | Reply |
| ASP | HORIZONTAL |
| ASD | VERTICAL |
AQWF*JSOCKET TAPER SIZE DESIGNATOR
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE SOCKET TAPER SIZE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AQWFJACTEXT1234*)
| Table 1 |
| Reply Code (AH09) | Reply |
| AD | BROWN AND SHARPE |
| AC | JARNO |
| AB | MORSE |
BGGM*DAUXILIARY HANDLE LOCATION
INDICATES THE LOCATION OF THE AUXILIARY HANDLE(S) ON THE ITEM.
Enter the applicable reply code from the table below
(BGGMDAEQ*;BGGMDABC$DABD*;BGGMDABC$$DABD*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABA | BOTTOM |
| ABC | FRONT |
| AEG | LEFT HAND SIDE |
| AEQ | RIGHT HAND SIDE |
| ABD | TOP |
AQFK*GLOUDNESS LEVEL IN DECIBELS
THE LEVEL OF A SIGNAL OR SOUND RELATIVE TO A SPECIFIC DISTANCE,EXPRESSED IN DECIBELS.
Enter clear text.
(AQFKGCLEARTEXT)
ALVS*BVIBRATION LEVEL IN METERS PER SECOND SQUARED
A NUMERIC VALUE INDICATING THE VIBRATION OUTPUT OF THE ITEM EXPRESSED IN METERS PER SECOND SQUARED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALVSB2.0)
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFLA*;CBBLDCZC$$DFHU*)
| Table 1 |
| Reply Code (AN47) | Reply |
| FKZ | 360 DEGREE SIDE HANDLE |
| FLA | BELT CLIP |
| FLB | BUILT-IN LEVEL |
| FHU | CORDLESS |
| FCF | DOUBLE INSULATED |
| FDJ | ELECTROMAGNETIC INTERFERENCE SUPPRESSION |
| CZC | FUNGUS RESISTANT |
| EDH | NONREVERSIBLE |
| FLC | PADDLE SWITCH |
| BWW | REVERSIBLE |
| FLD | SHOCKPROOF |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information