Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAU1173	60	FIXED, RECTANGULAR OUTLETS
DR04090	60A	FIXED, ROUND OUTLETS
AAU1174	61	FIXED
AAU1175	62	FIXED, RECTANGULAR OUTLETS
DR04091	62A	FIXED,ROUND OUTLETS
AAU1176	63	PORTABLE
AAU1177	64	RIXED, MULTISTAGE
AAU1178	65	FIXED, INVERTED, RECTANGULAR OUTLET
DR04096	65A	FIXED, INVERTED, ROUND OUTLET
AAU1179	66	FIXED
AAU1180	67	FIXED, DUAL, RETANGULAR, OUTLETS
DR04097	67A	FIXED, DUAL, ROUND OUTLETS

ABGL*JWIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABGLJAB2.0*;ABGLJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABRY*JLENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AJLU*JOUTLET INSIDE WIDTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJLUJAC2.0*;AJLUJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AJLV*JOUTLET INSIDE HEIGHT

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJLVJAA2.0*;AJLVJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AJLW*JOUTLET INSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJLWJAA2.0*;AJLWJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

HGTH*JHEIGHT

A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(HGTHJAB2.0*;HGTHJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

NMBR*AQUANTITY

A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.

Enter the numeric reply with a minimum of one digit.

(NMBRA10*)

MATTDMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(MATT3AEEDMG0008*;MATT3AEEDMG0008$DST1009*;MATT3AEEDMG0008$$DST1009*)

Table 1
	ISAC Field Indicator (5000)	Location
	3ACY	HOUSING
	3AEE	OVERALL
	3AEF	HANDLE
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (MA01)	Reply
	ALA000	ALUMINUM
	ALB000	ALUMINUM ALLOY
	AL2014	ALUMINUM ALLOY 2014
	AL2024	ALUMINUM ALLOY 2024
	AL0038	ALUMINUM ALLOY 222.0
	AL0025	ALUMINUM ALLOY 295.0
	AL3003	ALUMINUM ALLOY 3003
	AL0045	ALUMINUM ALLOY 355.0
	AL0046	ALUMINUM ALLOY 356.0
	AL0029	ALUMINUM ALLOY 360.0
	AL0031	ALUMINUM ALLOY 380.0
	AL4043	ALUMINUM ALLOY 4043
	AL0027	ALUMINUM ALLOY 413.0
	AL5052	ALUMINUM ALLOY 5052
	AL6061	ALUMINUM ALLOY 6061
	AL6063	ALUMINUM ALLOY 6063
	AL0028	ALUMINUM ALLOY A380.0
	AL0030	ALUMINUM ALLOY A413.0
	AL0206	ALUMINUM ALLOY A-S13
	AL0033	ALUMINUM ALLOY B443.0
	AL0024	ALUMINUM ALLOY D712.0
	CUA000	COPPER
	CUB000	COPPER ALLOY
	GSA000	GLASS
	GSB000	GLASS FIBER
	FEA000	IRON
	FEB000	IRON CAST
	FEC000	IRON MALLEABLE
	MGA000	MAGNESIUM
	MGB000	MAGNESIUM ALLOY
	MG0007	MAGNESIUM ALLOY AZ63A
	MG0014	MAGNESIUM ALLOY AZ81A
	MG0008	MAGNESIUM ALLOY AZ91C
	MG0009	MAGNESIUM ALLOY AZ92A
	MG0015	MAGNESIUM ALLOY EZ33A
	MG0016	MAGNESIUM ALLOY HZ32A
	MG0017	MAGNESIUM ALLOY ZK51A
	MG0006	MAGNESIUM ALLOY ZK60A
	MG0018	MAGNESIUM ALLOY ZK61A
	MNA000	MANGANESE
	NLA000	NICKEL
	NLB000	NICKEL ALLOY
	PCA000	PLASTIC
	PCB000	PLASTIC ACETAL
	PCBL00	PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS)
	PCAN00	PLASTIC CELLULOSE ACETATE
	PCG000	PLASTIC DIALLYL PHTHALATE
	PCH000	PLASTIC EPOXY
	PCJ000	PLASTIC MELAMINE
	PCM000	PLASTIC PHENOL FORMALDEHYDE (PMO)
	PCN000	PLASTIC PHENOLIC
	PCP000	PLASTIC POLYAMIDE (NYLON)
	PCR000	PLASTIC POLYCARBONATE
	PCW000	PLASTIC POLYESTER
	PCAB00	PLASTIC POLYOLEFIN
	PCAC00	PLASTIC POLYPROPYLENE
	PCAE00	PLASTIC POLYSULFONE
	PCAP00	PLASTIC VINYL
	RCE000	RUBBER
	RCA000	RUBBER NATURAL
	RCB000	RUBBER SYNTHETIC
	STA000	STEEL
	ST1006	STEEL COMP 1006
	ST1008	STEEL COMP 1008
	ST1009	STEEL COMP 1009
	ST1010	STEEL COMP 1010
	ST1015	STEEL COMP 1015
	ST1018	STEEL COMP 1018
	ST1020	STEEL COMP 1020
	ST1035	STEEL COMP 1035
	ST1040	STEEL COMP 1040
	ST1045	STEEL COMP 1045
	ST1050	STEEL COMP 1050
	ST1137	STEEL COMP 1137
	ST1141	STEEL COMP 1141
	ST1144	STEEL COMP 1144
	ST0304	STEEL COMP 304
	ST0403	STEEL COMP 403
	ST4340	STEEL COMP 4340
	ST4620	STEEL COMP 4620
	STB000	STEEL CORROSION RESISTING
	TTB000	TITANIUM
	TTA000	TITANIUM ALLOY
	WDC000	WOOD
	ZNB000	ZINC
	ZNA000	ZINC ALLOY
	ZN0013	ZINC ALLOY ZN-AL4CU1MG

CXJSDPRIME MOVER FOR WHICH DESIGNED

THE PRIME MOVER THE HOUSING IS DESIGNED TO ACCOMMODATE.

Enter the applicable reply code from the table below

(CXJSDAE*;CXJSDAD$DAC*;CXJSDAD$$DAC*)

Table 1
	Reply Code (AG27)	Reply
	AC	DIESEL ENGINE
	AD	ELECTRIC MOTOR
	AE	GASOLINE ENGINE

CWLY*DPRIME MOVER DRIVE SHAFT BEARING TYPE

INDICATES THE TYPE OF BEARING/S/ PROVIDED ON THE PRIME MOVER DRIVE SHAFT.

Enter the applicable reply code from the table below

(CWLYDAE*;CWLYDAK$DAE*;CWLYDAK$$DAE*)

Table 1
	Reply Code (AH96)	Reply
	AE	BALL
	AK	SLEEVE

AEHY*JAMBIENT TEMP AT FULL RATED POWER

THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEHYJC2.0*;AEHYJC2.0$$JC2.1*)

Table 1
	Reply Code (AB36)	Reply
	C	CELSIUS
	F	FAHRENHEIT

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDAHJ*;CBBLDAHD$$DAHA*)

Table 1
	Reply Code (AN47)	Reply
	AHA	ADJUSTABLE BLADE PITCH
	AHB	AIR FILTER
	AHC	COLLAR
	AHD	ELECTRIC NOISE SUPPRESSOR
	CNP	FLANGED AIR INLET
	CNQ	FLANGED AIR OUTLET
	AHE	FUMIGATED FOR STORAGE
	CNR	HORIZONTAL ADJUSTMENT
	AHF	INLET CONE
	AHG	INLET GUIDE VANES
	CNS	INLET SCREEN
	AHH	LOUVER
	AHJ	NONSPARKING
	AHK	OSCILLATING
	ABK	RADIO INTERFERENCE SHIELDING
	FNY	ROHS DIRECTIVE COMPLIANCE
	CNT	SAFETY IMPELLER GUARD
	CNU	SHOCK ABSORBER
	AHL	TAPERED BORE IMPELLER HUB
	AHM	THERMAL PROTECTIVE DEVICE
	CNV	VERTICAL ADJUSTMENT

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ENAC*DENVIRONMENTAL ATTRIBUTE CODE

INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.

Enter the applicable reply code from the table below

(ENACDJ9)

Table 1
	Reply Code (EN02)	Reply
	J4	CEILING FANS, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
	J9	ENERGY EFFICIENT - LIGHTING - CEILING FANS
	J7	VENTILATION FANS, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS