That part of an electrical meter which translates electrical energy into mechanical energy, the value of which is usually indicated by a pointer moving across a calibrated dial.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED60726*)
IF STYLE/REPLY CODE(s) ABC WERE ENTERED FOR MRC AQEC, YOU MUST ANSWER MRC (ANQD and APMP)
AQEC*DMOVEMENT TYPE
INDICATES THE TYPE OF MOVEMENT PROVIDED.
Enter the applicable reply code from the table below
(AQECDABA*;AQECDAAZ$$DAAY*)
| Table 1 |
| Reply Code (AL03) | Reply |
| AAW | ELECTRODYNAMOMETER |
| AAX | ELECTROSTATIC |
| AAY | MOVING COIL, PERMANENT MAGNET |
| AAZ | MOVING IRON VANE |
| ABA | MOVING MAGNET |
| ABB | THERMAL |
| ABC | VIBRATING REED |
ANQD*AREGISTER QUANTITY
THE NUMBER OF REGISTER(S) CONTAINED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ANQDA10*)
APMP*ARESONANT REED QUANTITY
THE SPECIFIC NUMBER OF RESONANT REEDS.
Enter the numeric reply with a minimum of one digit.
(APMPA10*)
CTQLDMOVEMENT SUSPENSION METHOD
THE MEANS EMPLOYED TO SUSPEND THE MOVEMENT OF THE ITEM.
Enter the applicable reply code from the table below
(CTQLDAQ*;CTQLDAP$$DAN*)
| Table 1 |
| Reply Code (AH72) | Reply |
| AP | JEWEL PIVOT BASE |
| AN | METAL PIVOT BASE |
| AQ | TAUT BAND |
ANTG*JSENSITIVITY RATING
THE RATED SENSITIVITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANTGJAAC2.0*;ANTGJAAC2.0$$JAAC2.1*)
| Table 1 |
| Reply Code (AK11) | Reply |
| AAP | AMPERES |
| AAR | DECIBELS |
| AAS | KILOHM PER VOLT |
| AAT | MEGOHM PER VOLT |
| AAC | MICROAMPERES |
| AAJ | MICROVOLTS |
| AAZ | MICROWATTS |
| AAD | MILLIAMPERES |
| AAE | MILLIVOLTS |
| AAW | MILLIWATTS |
| ABA | NANOWATTS |
| AAX | OHMS |
| AAB | OHMS PER VOLT |
| AAQ | VOLT-AMPERES |
| AAF | VOLTS |
| AAY | WATTS |
AAPB*BDIELECTRIC WITHSTANDING VOLTAGE IN VOLTS
THE MAXIMUM VOLTAGE THE INSULATING MATERIALS OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAPBB2.0)
AACTDCIRCUIT CURRENT FOR WHICH DESIGNED
THE TYPE OF ELECTRICAL CIRCUIT IN WHICH THE ITEM IS DESIGNED TO BE USED.
Enter the applicable reply code from the table below
(AACTDB*;AACTDC$DB*;AACTDC$$DB*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
CTWN*JOPERATING VOLTAGE RATING IN VOLTS
THE VALUE(S) OF ROOT MEAN SQUARE OR DIRECT CURRENT POTENTIAL WHICH MUST BE APPLIED TO THE ITEM FOR OPERATION,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTWNJCA2.0*;CTWNJCA2.0$$JCA2.1*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACZB*JFREQUENCY RATING
THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACZBJKB2.0*;ACZBJKB2.0$$JKB2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| E | HERTZ |
| K | KILOHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDB*;FAAZDA$DC*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
CTWZ*DINTERFACE COMPATIBILITY
THE TYPE AND/OR STANDARD INTERFACE SYSTEM WITH WHICH THE ITEM IS COMPATIBLE.
Enter the applicable reply code from the table below
(CTWZDCCH*;CTWZDCCJ$$DCCG*)
| Table 1 |
| Reply Code (AK95) | Reply |
| CCH | ATLAS |
| CCJ | BCD |
| CCF | IEEE-488 |
| BDE | PARALLEL |
| CCG | RS-232-C |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDALB000*;MATTDPCAAAA$DPCM000*;MATTDPCAAAA$$DPCM000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| LRA000 | LEATHER |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCCB00 | PLASTIC NYLON |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCR000 | PLASTIC POLYCARBONATE |
| PCAAAA | PLASTIC POLYPHENYLENE OXIDE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAAW0 | PLASTIC STYRENE ACRYLONITRILE |
| PCAP00 | PLASTIC VINYL |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| WDC000 | WOOD |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| B | 1ST MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDALA000*;SFTTDZNA000$DPCK000*;SFTTDZNA000$$DPCK000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ALA000 | ALUMINUM ALLOY |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CUB000 | COPPER ALLOY |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| ENB000 | ENAMEL LUSTERLESS |
| ENF000 | ENAMEL SEMIGLOSS |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PNG000 | PAINT LUSTERLESS |
| PCA000 | PLASTIC |
| PCK000 | PLASTIC ACRYLIC |
| PCH000 | PLASTIC VINYL |
| PRC000 | PRIMER ZINC CHROMATE |
| SNA000 | TIN |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
| EQ | NONHARDENED |
IF STYLE/REPLY CODE(s) P WERE ENTERED FOR MRC RADC, YOU MUST ANSWER MRC (RADD)
RADC*DRADIOACTIVE CONTENT
AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS.
Enter the applicable reply code from the table below
(RADCDP)
| Table 1 |
| Reply Code (AN54) | Reply |
| P | CONTAINS RADIOACTIVE MATERIAL |
RADD*JRADIONUCLIDES DATA
THE NAME AND AMOUNT OF THE RADIONUCLIDE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(RADDJJHAABM2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| JF | CURIES |
| LE | MEGABECQUERELS |
| JH | MICROCURIES |
| JG | MILLICURIES |
| Table 2 |
| Reply Code (AN55) | Reply |
| AAAB | ACTINIUM (89) AC-227 |
| AAAC | ACTINIUM (89) AC-228 |
| AAAD | AMERICIUM (95) AM-241 |
| AAAE | AMERICIUM (95) AM-243 |
| AAAF | ANTIMONY (51) SB-122 |
| AAAG | ANTIMONY (51) SB-124 |
| AAAH | ANTIMONY (51) SB-125 |
| AAAJ | ARGON (18) AR-37 |
| AAAK | ARGON (18) AR-41 |
| AAAL | ARGON (18) AR-41, UNCOMPRESSED |
| AAAM | ARSENIC (33) AS-73 |
| AAAN | ARSENIC (33) AS-74 |
| AAAP | ARSENIC (33) AS-76 |
| AAAQ | ARSENIC (33) AS-77 |
| AAAR | ASTATINE (85) AT-211 |
| AAAS | BARIUM (56) BA-131 |
| AAAT | BARIUM (56) BA-133 |
| AAAW | BARIUM (56) BA-140 |
| AAAX | BERKELIUM (97) BK-249 |
| AAAY | BERYLLIUM (4) BE-7 |
| AAAZ | BISMUTH (83) BI-206 |
| AABA | BISMUTH (83) BI-207 |
| AABB | BISMUTH (83) BI-210 |
| AABC | BISMUTH (83) BI-212 |
| AABD | BROMINE (35) BR-82 |
| AABE | CADMIUM (48) CD-109 |
| AABG | CADMIUM (48) CD-115 |
| AABF | CADMIUM (48) CD-115M |
| AABH | CALCIUM (20) CA-45 |
| AABJ | CALCIUM (20) CA-47 |
| AABK | CALIFORNIUM /98/ CF-249 |
| AABL | CALIFORNIUM /98/ CF-250 |
| AABM | CALIFORNIUM /98/ CF-252 |
| AABN | CARBON (6) C-14 |
| AABP | CERIUM (58) CE-141 |
| AABQ | CERIUM (58) CE-143 |
| AABR | CERIUM (58) CE-144 |
| AABS | CESIUM (55) CS-131 |
| AABW | CESIUM (55) CS-134 |
| AABT | CESIUM (55) CS-134M |
| AABX | CESIUM (55) CS-135 |
| AABY | CESIUM (55) CS-136 |
| AABZ | CESIUM (55) CS-137 |
| AACA | CHLORINE (17) CL-36 |
| AACB | CHLORINE (17) CL-38 |
| AACC | CHROMIUM (24) CR-51 |
| AACD | COBALT (27) CO-56 |
| AACE | COBALT (27) CO-57 |
| AACG | COBALT (27) CO-58 |
| AACF | COBALT (27) CO-58M |
| AACH | COBALT (27) CO-60 |
| AACJ | COPPER (29) CU-64 |
| AACK | CURIUM (96) CM-242 |
| AACL | CURIUM (96) CM-243 |
| AACM | CURIUM (96) CM-244 |
| AACN | CURIUM (96) CM-245 |
| AACP | CURIUM (96) CM-246 |
| AACQ | DYSPROSIUM (66) DY-154 |
| AACR | DYSPROSIUM (66) DY-165 |
| AACS | DYSPROSIUM (66) DY-166 |
| AACT | ERBIUM (68) ER-169 |
| AACW | ERBIUM (68) ER-171 |
| AACX | EUROPIUM (63) EU-150 |
| AACZ | EUROPIUM (63) EU-152 |
| AACY | EUROPIUM (63) EU-152M |
| AADA | EUROPIUM (63) EU-154 |
| AADB | EUROPIUM (63) EU-155 |
| AADC | FLUORINE (9) F-18 |
| AADD | GADOLINIUM (64) GD-153 |
| AADE | GADOLINIUM (64) GD-159 |
| AADF | GALLIUM (31) GA-67 |
| AADG | GALLIUM (31) GA-72 |
| AADH | GERMANIUM (32) GE-71 |
| AADJ | GOLD (79) AU-193 |
| AADK | GOLD (79) AU-194 |
| AADL | GOLD (79) AU-195 |
| AADM | GOLD (79) AU-196 |
| AADN | GOLD (79) AU-198 |
| AADP | GOLD (79) AU-199 |
| AADQ | HAFNIUM (72) HF-181 |
| AADR | HOLMIUM (67) HO-166 |
| AADS | INDIUM (49) IN-113M |
| AADT | INDIUM (49) IN-114M |
| AADX | INDIUM (49) IN-115 |
| AADW | INDIUM (49) IN-115M |
| AADY | IODINE (53) I-124 |
| AADZ | IODINE (53) I-125 |
| AAEA | IODINE (53) I-126 |
| AAEB | IODINE (53) I-129 |
| AAEC | IODINE (53) I-131 |
| AAED | IODINE (53) I-132 |
| AAEE | IODINE (53) I-133 |
| AAEF | IODINE (53) I-134 |
| AAEG | IODINE (53) I-135 |
| AAEH | IRIDIUM (77) IR-190 |
| AAEJ | IRIDIUM (77) IR-192 |
| AAEK | IRIDIUM (77) IR-194 |
| AAEL | IRON (26) FE-55 |
| AAEM | IRON (26) FE-59 |
| AAEQ | KRYPTON (36) KR-85 |
| AAER | KRYPTON (36) KR-85, UNCOMPRESSED |
| AAEN | KRYPTON (36) KR-85M |
| AAEP | KRYPTON (36) KR-85M, UNCOMPRESSED |
| AAES | KRYPTON (36) KR-87 |
| AAET | KRYPTON (36) KR-87, UNCOMPRESSED |
| AAEW | LANTHANUM (57) LA-140 |
| AAEX | LEAD (82) PB-203 |
| AAEY | LEAD (82) PB-210 |
| AAEZ | LEAD (82) PB-212 |
| AAFA | LUTECIUM (71) LU-172 |
| AAFB | LUTECIUM (71) LU-177 |
| AAFC | MAGNESIUM (12) MG-28 |
| AAFD | MANGANESE (25) MN-52 |
| AAFE | MANGANESE (25) MN-54 |
| AAFF | MANGANESE (25) MN-56 |
| AAFH | MERCURY (80) HG-197 |
| AAFG | MERCURY (80) HG-197M |
| AAFJ | MERCURY (80) HG-203 |
| AAFK | MIXED FISSION PRODUCTS MF-P |
| AAFL | MOLYBDENUM (42) MO-99 |
| AAFM | NEODYMIUM (60) ND-147 |
| AAFN | NEODYMIUM (60) ND-149 |
| AAFP | NEPTUNIUM (93) NP-237 |
| AAFQ | NEPTUNIUM (93) NP-239 |
| AAFR | NICKEL (28) NI-56 |
| AAFS | NICKEL (28) NI-59 |
| AAFT | NICKEL (28) NI-63 |
| AAFW | NICKEL (28) NI-65 |
| AAFX | NIOBIUM (41) NB-93M |
| AAFY | NIOBIUM (41) NB-95 |
| AAFZ | NIOBIUM (41) NB-97 |
| AAGA | OSMIUM (76) OS-185 |
| AAGC | OSMIUM (76) OS-191 |
| AAGB | OSMIUM (76) OS-191M |
| AAGD | OSMIUM (76) OS-193 |
| AAGE | PALLADIUM (46) PD-103 |
| AAGF | PALLADIUM (46) PD-109 |
| AAGG | PHOSPHORUS (15) P-32 |
| AAGH | PLATINUM (78) PT-191 |
| AAGJ | PLATINUM (78) PT-193 |
| AAGK | PLATINUM (78) PT-193M |
| AAGM | PLATINUM (78) PT-197 |
| AAGL | PLATINUM (78) PT-197M |
| AAGN | PLUTONIUM (94) PU-238 |
| AAGP | PLUTONIUM (94) PU-239 |
| AAGQ | PLUTONIUM (94) PU-240 |
| AAGR | PLUTONIUM (94) PU-241 |
| AAGS | PLUTONIUM (94) PU-242 |
| AAGT | POLONIUM (84) PO-210 |
| AAGW | POTASSIUM (19) K-42 |
| AAGX | POTASSIUM (19) K-43 |
| AAGY | PRASEODYMIUM (59) PR-142 |
| AAGZ | PRASEODYMIUM (59) PR-143 |
| AAHA | PROMETHIUM (61) PM-147 |
| AAHB | PROMETHIUM (61) PM-149 |
| AAHC | PROTACTINIUM (91) PA-230 |
| AAHD | PROTACTINIUM (91) PA-231 |
| AAHE | PROTACTINIUM (91) PA-233 |
| AAHF | RADIUM (88) RA-223 |
| AAHG | RADIUM (88) RA-224 |
| AAHH | RADIUM (88) RA-226 |
| AAHJ | RADIUM (88) RA-228 |
| AAHK | RADON (86) RN-220 |
| AAHL | RADON (86) RN-222 |
| AAHM | RHENIUM (75) RE-183 |
| AAHN | RHENIUM (75) RE-186 |
| AAHP | RHENIUM (75) RE-187 |
| AAHQ | RHENIUM (75) RE-188 |
| AAHR | RHENIUM (75) RE-NATURAL |
| AAHS | RHODIUM (45) RH-103M |
| AAHT | RHODIUM (45) RH-105 |
| AAHW | RUBIDIUM (37) RB-86 |
| AAHX | RUBIDIUM (37) RB-87 |
| AAHY | RUBIDIUM (37) RB-NATURAL |
| AAJA | RUTHENIUM (44) RU-103 |
| AAJB | RUTHENIUM (44) RU-105 |
| AAJC | RUTHENIUM (44) RU-106 |
| AAHZ | RUTHENIUM (44) RU-97 |
| AAJD | SAMARIUM (62) SM-145 |
| AAJE | SAMARIUM (62) SM-147 |
| AAJF | SAMARIUM (62) SM-151 |
| AAJG | SAMARIUM (62) SM-153 |
| AAJH | SCANDIUM (21) SC-46 |
| AAJJ | SCANDIUM (21) SC-47 |
| AAJK | SCANDIUM (21) SC-48 |
| AAJL | SELENIUM (34) SE-75 |
| AAJM | SILICON (14) SI-31 |
| AAJN | SILVER (47) AG-105 |
| AAJP | SILVER (47) AG-110M |
| AAJQ | SILVER (47) AG-111 |
| AAJR | SODIUM (11) NA-22 |
| AAJS | SODIUM (11) NA-24 |
| AAJW | STRONTIUM (38) SR-85 |
| AAJT | STRONTIUM (38) SR-85M |
| AAJX | STRONTIUM (38) SR-89 |
| AAJY | STRONTIUM (38) SR-90 |
| AAJZ | STRONTIUM (38) SR-91 |
| AAKA | STRONTIUM (38) SR-92 |
| AAKB | SULPHUR (16) S-35 |
| AAKC | TANTALUM (73) TA-182 |
| AAKE | TECHNETIUM (43) TC-96 |
| AAKD | TECHNETIUM (43) TC-96M |
| AAKG | TECHNETIUM (43) TC-97 |
| AAKF | TECHNETIUM (43) TC-97M |
| AAKJ | TECHNETIUM (43) TC-99 |
| AAKH | TECHNETIUM (43) TC-99M |
| AAKK | TELLURIUM (52) TE-125M |
| AAKM | TELLURIUM (52) TE-127 |
| AAKL | TELLURIUM (52) TE-127M |
| AAKP | TELLURIUM (52) TE-129 |
| AAKN | TELLURIUM (52) TE-129M |
| AAKQ | TELLURIUM (52) TE-131M |
| AAKR | TELLURIUM (52) TE-132 |
| AAKS | TERBIUM (65) TB-160 |
| AAKT | THALLIUM (81) TL-200 |
| AAKW | THALLIUM (81) TL-201 |
| AAKX | THALLIUM (81) TL-202 |
| AAKY | THALLIUM (81) TL-204 |
| AAKZ | THORIUM (90) TH-227 |
| AALA | THORIUM (90) TH-228 |
| AALB | THORIUM (90) TH-230 |
| AALC | THORIUM (90) TH-231 |
| AALD | THORIUM (90) TH-232 |
| AALE | THORIUM (90) TH-234 |
| AALF | THORIUM (90) TH-NATURAL |
| AALG | THULIUM (69) TM-168 |
| AALH | THULIUM (69) TM-170 |
| AALJ | THULIUM (69) TM-171 |
| AALK | TIN (50) SN-113 |
| AALL | TIN (50) SN-117M |
| AALM | TIN (50) SN-121 |
| AALN | TIN (50) SN-125 |
| AALP | TRITIUM (1) H-3 |
| AALQ | TRITIUM (1) H-3 AS GAS, LUMINOUS PAINT, OR ADSORBED ON SOLID MATERIAL |
| AALR | TUNGSTEN (74) W-181 |
| AALS | TUNGSTEN (74) W-185 |
| AALT | TUNGSTEN (74) W-187 |
| AALW | URANIUM (92) U-230 |
| AALX | URANIUM (92) U-232 |
| AALY | URANIUM (92) U-233 |
| AALZ | URANIUM (92) U-234 |
| AAMA | URANIUM (92) U-235 |
| AAMB | URANIUM (92) U-236 |
| AAMC | URANIUM (92) U-238 |
| AAMF | URANIUM (92) U-DEPLETED |
| AAME | URANIUM (92) U-ENRICHED |
| AAMD | URANIUM (92) U-NATURAL |
| AAMG | VANADIUM (23) V-48 |
| AAMH | VANADIUM (23) V-49 |
| AAMJ | XENON (54) XE-125 |
| AAMK | XENON (54) XE-131M |
| AAML | XENON (54) XE-131M, UNCOMPRESSED |
| AAMM | XENON (54) XE-133 |
| AAMN | XENON (54) XE-133, UNCOMPRESSED |
| AAMP | XENON (54) XE-135 |
| AAMQ | XENON (54) XE-135, UNCOMPRESSED |
| AAMR | YTTERBIUM (70) YB-175 |
| AAMS | YTTRIUM (39) Y-88 |
| AAMT | YTTRIUM (39) Y-90 |
| AAMX | YTTRIUM (39) Y-91 |
| AAMW | YTTRIUM (39) Y-91M |
| AAMY | YTTRIUM (39) Y-92 |
| AAMZ | YTTRIUM (39) Y-93 |
| AANA | ZINC (30) ZN-65 |
| AANC | ZINC (30) ZN-69 |
| AANB | ZINC (30) ZN-69M |
| AAND | ZIRCONIUM (40) ZR-93 |
| AANE | ZIRCONIUM (40) ZR-95 |
| AANF | ZIRCONIUM (40) ZR-97 |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDABL*;ADZCDAAD$$DAAP*)
| Table 1 |
| Reply Code (AA65) | Reply |
| ADC | AIRTIGHT |
| ACB | COLD RESISTANT |
| ACY | CORROSION PROOF |
| AAC | CORROSION RESISTANT |
| AAD | DRIPPROOF |
| AAF | DUST RESISTANT |
| ACZ | DUST TIGHT |
| AAE | DUSTPROOF |
| ADA | EROSION PROOF |
| AAG | EXPLOSION PROOF |
| AAJ | FIRE RESISTANT |
| AAM | FUNGUS PROOF |
| AAN | FUNGUS RESISTANT |
| AAP | HEAT RESISTANT |
| ADB | HERMETIC |
| ABP | HUMIDITY PROOF |
| AAR | HUMIDITY RESISTANT |
| ABQ | SALT SPRAY RESISTANT |
| ABA | SALT WATER RESISTANT |
| ABB | SAND PROOF |
| ABD | SHOCK PROOF |
| ABE | SHOCK RESISTANT |
| ABR | SPLASH PROOF |
| ABT | SPRAY TIGHT |
| ABW | SUBMERSIBLE |
| ABH | VIBRATION PROOF |
| ABJ | VIBRATION RESISTANT |
| ACM | WATER RESISTANT |
| ABK | WATERPROOF |
| ABL | WATERTIGHT |
| ADD | WINDPROOF |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCGC*;CBBLDCFY$$DBGA*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BGA | ADAPTER |
| CFH | ADJUSTABLE INDEX POINTER |
| CFJ | AUTORANGING |
| CFK | ELECTRICAL OVERLOAD PROTECTION |
| BDT | ELECTROSTATIC SHIELD |
| CPZ | EXTENSION CABLE |
| CFL | EXTERNAL SHUNTING |
| ANK | INTERNAL BATTERY ACCOMMODATION |
| CFM | INTERNAL FREQUENCY CALIBRATING CRYSTAL |
| CFN | INTERNAL SHUNTING |
| CFP | JAW INSULATION |
| CFQ | KNIFE EDGE POINTER |
| CFR | LUMINOUS SCALE MARKING |
| BDS | MAGNETIC SHIELD |
| CFS | MAXIMUM VALUE INDICATOR |
| CFT | MIRROR SCALE |
| CFW | NONGLARE GLASS |
| CFX | OVERRANGING |
| CFY | PORTABLE |
| CFZ | RECTIFIER CIRCUIT |
| AGQ | RFI SHIELDING |
| CGA | SELF-ILLUMINATION FACILITY |
| CGB | SHATTERPROOF GLASS |
| CCW | TEMPERATURE COMPENSATOR |
| AJX | TRANSFORMER |
| CGC | TUNABLE |
| CER | WARNING FEATURE |
| CGD | ZERO ADJUSTER |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
AARG*DRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDE)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDRHA000$DAZA000*;PRMTDRHA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000E2.0*;PMWTJRHA000E2.0$JRHA000E2.0*;PMWTJRHA000E2.0$$JRHA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAT3)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAD4)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information