A sling fabricated from a single length of webbing termination at each end in a built in loop or attachments. See also CHAIN ASSEMBLY, SINGLE LEG; FIBER ROPE ASSEMBLY, SINGLE LEG and WIRE ROPE ASSEMBLY, SINGLE LEG.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED49592*)
BQHKJLIFTING CAPACITY
THE LIFTING CAPACITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQHKJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AAADRSD000*;MATT3AAADRSD000$DPCW000*;MATT3AAADRSD000$$DPCW000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAA | FIRST MORTISE |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AEV | BOTH ENDS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| ALE000 | ALUMINUM OXIDE |
| SBA000 | ANTIMONY |
| ASA000 | ASBESTOS |
| CNA000 | CARBON |
| CXA000 | CEMENT |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| FEB000 | IRON CAST |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCCB00 | PLASTIC NYLON |
| PCW000 | PLASTIC POLYESTER |
| RSD000 | RESIN |
| STA000 | STEEL |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
FMATDFIBER MATERIAL
THE ELEMENT,CHEMICAL COMPOUND,OR MECHANICAL MIXTURE PROPERTIES OF THE FIBER,OR THE GENERIC NAME BY WHICH THE MANUFACTURED FIBER IS KNOWN AND/OR IDENTIFIED.
Enter the applicable reply code from the table below
(FMATDPSQ)
| Table 1 |
| Reply Code (MA02) | Reply |
| ACT | ACETATE |
| ACC | ACRYLIC |
| AZN | AZLON |
| CRF | CARBON-FILAMENT |
| CLS | CELLULOSE |
| CSL | CELLULOSE ETHYL |
| NLN | NYLON |
| NTL | NYTRIL |
| PPS | PLASTIC POLYSTYRENE |
| PLR | PLASTIC URETHANE |
| PLB | POLYAMIDE-FILAMENT |
| PLA | POLYAMIDE-STAPLE |
| PBM | POLYBENZIMIDAZOLE |
| PSR | POLYESTER |
| PSS | POLYESTER-FILAMENT |
| PSQ | POLYESTER-STAPLE |
| AAH | POLYPROPYLENE |
| PRN | POLYURETHANE |
| SYN | SYNTHETIC |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDAW*;ADZCDJP$DAA*;ADZCDJP$$DAA*)
| Table 1 |
| Reply Code (AA65) | Reply |
| AA | ABRASION RESISTANT |
| ET | ACCELERATED LIGHT |
| JP | ACID FUME |
| AW | CHEMICAL RESISTANT |
ABRYJLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAC2.0*;ABRYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGLJWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAB2.0*;ABGLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDBL0039*;HUESDGR0075$DGY0072*;HUESDGR0075$$DGY0072*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BE0000 | BEIGE |
| BL0000 | BLACK |
| BL0039 | BLACK, LUSTERLESS |
| BU0000 | BLUE |
| BU0088 | BLUE, FED STD 595, 15123 |
| BU0033 | BLUE, NAVY |
| BR0000 | BROWN |
| BR0173 | BROWN, FED STD 595, 30279 |
| GL0000 | GOLD |
| GY0004 | GRAY, AIRCRAFT |
| GY0074 | GRAY, CINDER |
| GY0008 | GRAY, DARK |
| GY0049 | GRAY, DARK GULL |
| GY0171 | GRAY, FED STD 595, 26152 |
| GY0029 | GRAY, FED STD 595, 36231 |
| GY0155 | GRAY, FED STD 595, 36251 |
| GY0134 | GRAY, FED STD 595, 36270 |
| GY0033 | GRAY, FED STD 595, 36440 |
| GY0013 | GRAY, LIGHT GULL |
| GY0047 | GRAY, NATURAL |
| GY0072 | GRAY, NAVY |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| GR0075 | GREEN, ARMY |
| GR0019 | GREEN, CRAYON |
| GR0020 | GREEN, DARK |
| GR0247 | GREEN, FED STD 595, 34052 |
| GR0073 | GREEN, FED STD 595, 34087 |
| GR0024 | GREEN, FOREST |
| GR0006 | GREEN, MEDIUM |
| GR0137 | GREEN, NAVY |
| GR0011 | GREEN, OLIVE |
| GR0007 | GREEN, SAGE |
| GR0064 | GREEN, SAGE, 1531 |
| GR0447 | GREEN, US AIR FORCE, 1001 |
| GR0119 | GREEN, US MARINE CORPS |
| KH0000 | KHAKI |
| NA0000 | NATURAL |
| LD0000 | OLIVE DRAB |
| LD0012 | OLIVE DRAB, US ARMY, 7 |
| RG0002 | ORANGE-YELLOW |
| RE0000 | RED |
| RU0000 | RUSSET |
| TA0000 | TAN |
| MS0054 | TAUPE |
| WH0000 | WHITE |
| WH0013 | WHITE, IVORY |
| WH0023 | WHITE, NATURAL |
| YE0000 | YELLOW |
| YE0036 | YELLOW, FED STD 595, 13538 |
BTLM*DATTACHMENT METHOD FOR WHICH DESIGNED
THE ATTACHMENT MEANS FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BTLMDAAZ*;BTLMDQJ$DABC*;BTLMDQJ$$DABC*)
| Table 1 |
| Reply Code (AA78) | Reply |
| AAZ | BUCKLE |
| ABA | CEMENTED |
| QF | EYELET |
| QG | GROMMET |
| QH | HEAT SEAL |
| QJ | RIVETED |
| QK | SEWED |
| ABC | SLIDE LOOP |
| QL | SNAP FASTENER |
IF STYLE/REPLY CODE(s) HF, HL, JH, JJ, JN, JT, JX OR RR WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (BYCB)
ACLSDSECOND END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACLSDXY)
| Table 1 |
| Reply Code (AB76) | Reply |
| SB | ADJUSTABLE FLANGE |
| ACP | CLEVIS |
| GZ | CLEVIS W/BOLT |
| HA | CLEVIS W/LOCKING PIN |
| HB | CLEVIS W/PIPE PIN |
| HC | CLEVIS W/WELD |
| BM | COMPANION FLANGE UNION |
| HE | DOUBLE EYE HOOK |
| HF | DOUBLE SPRING LOCK HOOK |
| EB | DRILLED FLANGE |
| FF | DUAL PANEL JACK |
| HK | EYE CLEVIS |
| HL | EYE HOOK |
| ACV | FLANGE |
| BS | FLANGE UNION |
| ACS | FLANGE W/BAIL |
| HQ | FLANGE W/HOLE |
| XX | FLANGE, OVAL W/HOLES |
| XY | FLANGE, OVAL W/O HOLES |
| AAR | FLANGE, RECTANGULAR W/HOLES |
| AAS | FLANGE, RECTANGULAR W/O HOLES |
| AAT | FLANGE, ROUND W/HOLES |
| AAU | FLANGE, ROUND W/O HOLES |
| XV | FLANGE, SQUARE W/HOLES |
| XW | FLANGE, SQUARE W/O HOLES |
| AAD | FLANGED |
| SW | FLANGED PIPE |
| BT | FLANGED, ENDS SEALED |
| SZ | FLANGED, PLAIN |
| TA | FLANGED, RAISED |
| TB | FLANGED, RAISED, W/COUNTERBORE |
| TC | FLANGED, RECESSED |
| HZ | FORKED W/LOCKING HOOK |
| MG | GROOVED FACE FLANGE |
| JH | HOOK |
| JJ | HOOK W/LOCKING PIN |
| RR | HOOK W/SPRING LOCK |
| GA | INTEGRAL FLANGE |
| PG | MOUNTING FLANGE |
| JN | PINTLE HOOK |
| PB | PLAIN FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| TF | REDUCED SOCKET W/ONE BRAZING RING |
| JR | RING DRAWBAR COUPLER |
| FE | SINGLE PANEL JACK |
| JT | SLIP HOOK W/LOCKING BAR |
| WN | SPLIT FLANGE |
| JX | STRAIGHT HOOK |
| TH | STREAMLINED, W/ONE BRAZING RING |
| TJ | STREAMLINED, W/TWO BRAZING RINGS |
| BZ | SWEAT FLANGE |
| KA | TOWING LUG |
| KB | TOWING RING |
| EC | UNDRILLED FLANGE |
IF STYLE/REPLY CODE(s) HF, HL, JH, JJ, JN, JT, JX OR RR WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (BYCB)
ACKMDFIRST END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACKMDAAS)
| Table 1 |
| Reply Code (AB76) | Reply |
| SB | ADJUSTABLE FLANGE |
| ACP | CLEVIS |
| GZ | CLEVIS W/BOLT |
| HA | CLEVIS W/LOCKING PIN |
| HB | CLEVIS W/PIPE PIN |
| HC | CLEVIS W/WELD |
| BM | COMPANION FLANGE UNION |
| HE | DOUBLE EYE HOOK |
| HF | DOUBLE SPRING LOCK HOOK |
| EB | DRILLED FLANGE |
| FF | DUAL PANEL JACK |
| HK | EYE CLEVIS |
| HL | EYE HOOK |
| ACV | FLANGE |
| BS | FLANGE UNION |
| ACS | FLANGE W/BAIL |
| HQ | FLANGE W/HOLE |
| XX | FLANGE, OVAL W/HOLES |
| XY | FLANGE, OVAL W/O HOLES |
| AAR | FLANGE, RECTANGULAR W/HOLES |
| AAS | FLANGE, RECTANGULAR W/O HOLES |
| AAT | FLANGE, ROUND W/HOLES |
| AAU | FLANGE, ROUND W/O HOLES |
| XV | FLANGE, SQUARE W/HOLES |
| XW | FLANGE, SQUARE W/O HOLES |
| AAD | FLANGED |
| SW | FLANGED PIPE |
| SZ | FLANGED, PLAIN |
| TA | FLANGED, RAISED |
| TB | FLANGED, RAISED, W/COUNTERBORE |
| TC | FLANGED, RECESSED |
| HZ | FORKED W/LOCKING HOOK |
| MG | GROOVED FACE FLANGE |
| JH | HOOK |
| JJ | HOOK W/LOCKING PIN |
| RR | HOOK W/SPRING LOCK |
| GA | INTEGRAL FLANGE |
| PG | MOUNTING FLANGE |
| JN | PINTLE HOOK |
| PB | PLAIN FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| TF | REDUCED SOCKET W/ONE BRAZING RING |
| JR | RING DRAWBAR COUPLER |
| FE | SINGLE PANEL JACK |
| JT | SLIP HOOK W/LOCKING BAR |
| WN | SPLIT FLANGE |
| JX | STRAIGHT HOOK |
| TH | STREAMLINED, W/ONE BRAZING RING |
| TJ | STREAMLINED, W/TWO BRAZING RINGS |
| BZ | SWEAT FLANGE |
| ST | TERMINAL STUD |
| KA | TOWING LUG |
| KB | TOWING RING |
| EC | UNDRILLED FLANGE |
BYCB*LHOOK STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOOK(S).
Enter the applicable ISAC from the table below folowed by the mode code and the applicable reply code from the drawing group below.
(BYCB3AEULC2*;BYCB3AEULC2$LC8*;BYCB3AEULC2$$LC8*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AEV | BOTH ENDS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AZ10082 | C1 | PIVOT SNAP |
| AZ10091 | C10 | TRIGGER SNAP |
| AZ10092 | C11 | TRIGGER SNAP |
| AZ10093 | C12 | TRIGGER SNAP |
| AZ10083 | C2 | PIVOT SNAP |
| AZ10084 | C3 | PIVOT SNAP |
| AZ10085 | C4 | PIVOT SNAP |
| AZ10086 | C5 | PIVOT SNAP |
| AZ10087 | C6 | SLIDING BOLT SNAP |
| AZ10088 | C7 | SLIDING BOLT SNAP |
| AZ10089 | C8 | SPRING BLADE SNAP |
| AZ10090 | C9 | SPRING BLADE SNAP |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information