An item which retains a rifle, shotgun or the like in a vehicular cab, body or turret. It may be a component of a rack or cabinet. The weapon must be removed from its stowed position prior to usage. Excludes:BRACKET (1), MOUNTING.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED46727*)
IF YOU ANSWER MRC MATT, YOU MUST ANSWER MRC (MDCL)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDALA000*;MATTDSTF000$DZRF000*;MATTDSTF000$$DZRF000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5086 | ALUMINUM ALLOY 5086 |
| ZSA003 | ALUMINUM ALLOY 6061, TYPE 651 |
| RCE000 | RUBBER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| ZRF000 | STEEL,ARMOR |
| STF000 | STEEL,CARBON |
SHPEDSHAPE
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(SHPEDASL)
| Table 1 |
| Reply Code (AD07) | Reply |
| AAD | ANGLED |
| BLR | DOUBLE ANGLE |
| AJG | IRREGULAR |
| ASL | SQUARE |
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAD0)
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDTT*;HEATDEN$DEX*;HEATDEN$$DEX*)
| Table 1 |
| Reply Code (AD05) | Reply |
| BP | ANNEALED |
| CR | COLD DRAWN |
| CX | COLD ROLLED |
| EX | H-111 STRAIN HARDENED |
| GB | H-116 SPECIALLY TREATED |
| TP | H-24 STRAIN HARDENED, PARTIALLY ANNEALED TO 1/2 HARD |
| TQ | H-32 STRAIN HARDENED, STABILIZED TO 1/4 HARD |
| QP | H-321 STRAIN HARDENED |
| LL | H-323 STRAIN HARDENED AND STABILIZED |
| TR | H-34 STRAIN HARDENED, STABILIZED TO 1/2 HARD |
| TS | H-36 STRAIN HARDENED, STABILIZED TO 3/4 HARD |
| TT | H-38 STRAIN HARDENED, STABILIZED TO FULL HARD |
| CH | HARD |
| CY | HARDENED |
| CT | HOT ROLLED |
| JQ | PICKLED |
| EN | QUENCHED |
| EP | TEMPERED |
CYHX*AVEHICLE DESIGN CONTROL ACTIVITY
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VEHICLE.
Enter the alpha-numeric reply with five character(s) exactly.
(CYHXAD1F0P)
CYHY*AVEHICLE IDENTIFICATION DESIGNATOR
THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC VEHICLE.
Enter the alpha-numeric reply with a minimum of one character.
(CYHYAR6)
IF YOU ANSWER MRC SFTT, YOU MUST ANSWER MRC (STDC)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDAAA012*;SFTTDPRF000$DAAA004*;SFTTDPRF000$$DAAA004*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| AAA013 | CARC (CHEMICAL AGENT RESISTANT COATING), ALIPHATIC POLYURETHANE |
| AAA012 | CARC (CHEMICAL AGENT RESISTANT COATING), POWDER |
| AAA002 | CHEMICAL |
| PNA000 | PAINT |
| AAA011 | POLYURETHANE PAINT-LEAD,CADMIUM AND HEXAVALENT CHROMIUM FREE |
| AAA004 | POWDER COATED |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| PRA001 | PRIMER EPOXY-LEAD AND CHROMIUM FREE |
| ZNM000 | PRIMER-HEXAVALENT CHROMIUM FREE |
| AAA010 | PRIMER-LEAD AND HEXAVALENT CHROMIUM FREE |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$JAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACHY*DMOUNTING HOLE TYPE
INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(ACHYDB*;ACHYDW$DU*;ACHYDW$$DU*)
| Table 1 |
| Reply Code (AB68) | Reply |
| A | COUNTERBORED |
| B | COUNTERSUNK |
| Q | KEYHOLE |
| Y | OBLONG |
| L | PIVOT PIN |
| C | PLAIN |
| Z | RIVETED |
| W | ROUND, THREADED |
| T | ROUND, UNTHREADED |
| N | SERRATED |
| P | SLOTTED |
| M | STUD |
| R | TAPER HOLE |
| F | TAPER PIN PILOT |
| K | TAPERED |
| D | THREADED |
| G | THREADED-COUNTERBORED |
| H | THREADED-COUNTERSUNK |
| S | THREADED-EXTRUDED |
| U | THRU HOLE |
| E | UNTHREADED |
| J | UNTHREADED-COUNTERSUNK |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABGD*JSLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGDJAB2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDTA0099)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| GR0000 | GREEN |
| GR0492 | GREEN 383, 34094 |
| TA0000 | TAN |
| TA0099 | TAN, 686A |
| WH0000 | WHITE |
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDPP)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AC | ACME C |
| AG | ACME G |
| MM | ACME-MODIFIED |
| MS | ACME-SPECIAL |
| AS | AMERICAN STANDARD |
| MP | AMPT |
| AN | ANPT |
| AU | ANSFH |
| PA | API |
| PB | API IF |
| RE | API REG |
| PC | API STANDARD |
| AP | APSC |
| GA | ARMOURED CONDUIT, DIN 40430 |
| AW | ASA |
| BM | ASA HOSE |
| AV | ASH |
| BA | BA |
| RZ | BRASS |
| CJ | BRITISH NONSTANDARD WHITFORM |
| DP | BRITISH STANDARD BUTTRESS |
| CY | BRITISH STANDARD CYCLE THREAD |
| CQ | BS CON |
| BF | BSF |
| ZP | BSP. L |
| DQ | BSP.C |
| FB | BSP.F |
| BE | BSP.F EXT |
| BT | BSP.F INT |
| PL | BSP.PL |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BP | BSP.TR |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| TP | BSTP |
| BW | BSW |
| TT | BUTTRESS |
| CS | CALIF STANDARD |
| CH | CHEMICAL HOSE |
| DW | COARSE |
| CT | CUTTING |
| DD | DARDALET |
| DE | DEVILBISS |
| DF | DEVILBISS STANDARD |
| DM | DISSYMMETRICAL PROFILE NF L05-420 |
| DS | DOUBLE STUB |
| DR | DRIVE |
| CL | EF |
| FN | FINE |
| FM | FORMING |
| FP | F-PTF |
| DX | FRENCH CONDUIT THREAD NF C68-190 |
| GE | G |
| CM | INTERNATIONAL METRIC FINE THREAD |
| AD | INTERNATIONAL SPECIAL |
| AR | INTERNATIONAL STANDARD |
| AE | IPS |
| CR | ISO FINE THREAD PITCH SERIES 1 |
| CW | ISO FINE THREAD PITCH SERIES 2 |
| CX | ISO FINE THREAD PITCH SERIES 3 |
| CZ | ISO FINE THREAD PITCH SERIES 4 |
| SY | ISO FORM |
| SM | ISO M |
| ME | ISO METRIC FINE |
| SS | ISO S |
| JL | JIC |
| LH | LOWENHERZ |
| EM | M |
| CN | METRIC |
| MN | METRIC NONSTD |
| MX | METRIC TAPERED EXTERNAL |
| MB | METRIC TAPERED EXTERNAL, DIN 158 |
| MJ | MJ |
| MF | MODIFIED ACME 2G |
| MA | MODIFIED AMERICAN NATIONAL STANDARD STRAIGHT PIPE |
| CA | N |
| NX | N 5 |
| AB | N ACME BOX |
| AX | N SPECIAL |
| BZ | N STD |
| EN | N-12 |
| YN | N-16 |
| ZN | N-2 |
| NA | N-3 ACME |
| NB | N-4 STANDARD |
| DN | NATIONAL GAS ASSOCIATION |
| BX | NC |
| CE | NC-2 |
| NY | NC-2X |
| NL | NCT |
| NQ | NEF |
| ET | NET |
| BY | NF |
| CB | NF-1 |
| CC | NF-2 |
| FS | NFS |
| NG | NGO |
| GS | NGS |
| GT | NGT |
| AF | NGTD |
| AH | NGTI |
| AJ | NGTP |
| NH | NH |
| NZ | NH-SPCL |
| NK | NONSTANDARD ROUND |
| BB | NONSTANDARD SPECIAL |
| PN | NP |
| PG | NPI |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| AK | NPSN |
| NP | NPT |
| AL | NPTA |
| NT | NPTF |
| PR | NPT-MODIFIED |
| TR | NPTR |
| TS | NPTS |
| AQ | NS |
| SN | NS-2 |
| NW | NSPT |
| PK | PACIFIC COAST |
| LN | PL INT BS61 |
| PW | PT |
| PH | PTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| RR | R |
| RH | RAN HOSE |
| RL | RL |
| LB | RL(BSPL) |
| RD | ROUND |
| RJ | ROUND, DIN 20400 |
| RG | ROUND, DIN 405 |
| RM | ROUND, DIN 70156 |
| RK | ROUND, DIN 7272 |
| RP | RPT |
| RS | RS |
| SW | SAE |
| LT | SAE-LT |
| SG | SGT |
| SJ | SI |
| DA | SI FINE THREAD PITCH SERIES 1 |
| DB | SI FINE THREAD PITCH SERIES 2 |
| DC | SI FINE THREAD PITCH SERIES 3 |
| DJ | SI FINE THREAD PITCH SERIES 4 |
| DK | SI FINE THREAD PITCH SERIES 5 |
| SX | SI FORM |
| SK | SI-M |
| AY | SPECIAL |
| AZ | SPECIAL ACME |
| CF | SPECIAL MODIFIED WHITWORTH |
| PQ | SPT |
| SQ | SQUARE |
| SD | STANDARD ACME DOUBLE LEAD |
| ST | STD STUB ACME |
| CP | STEWART WARNER SPECIAL |
| SR | STI |
| SA | STUB ACME |
| SZ | STUB ACME DOUBLE LEAD |
| SE | STUB ACME M1 |
| SB | STUB ACME M2 |
| MT | SUBMARINE THD |
| TD | TAPER DRIVE |
| EX | TR EXT BS61 |
| RN | TR INT BS61 |
| TZ | TRAPEZIUM |
| AT | TWPP |
| UN | UN |
| NR | UN FORM |
| FF | UN-12 |
| FG | UN-16 |
| ZA | UN-20 |
| ZB | UN-28 |
| ZC | UN-32 |
| FC | UN-4 |
| FD | UN-6 |
| FE | UN-8 |
| NC | UNC |
| DL | UNC DOUBLE LEAD |
| DG | UND |
| BK | UNDERWRITERS |
| CG | UNDERWRITERS STANDARD TIP |
| NE | UNEF |
| DH | UNEF-2A |
| YM | UNEF-MODIFIED |
| NF | UNF |
| MD | UNF-MODIFIED |
| BD | UNG |
| BQ | UNIFIED |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NM | UNM |
| ND | UN-MODIFIED |
| HR | UNR |
| RC | UNRC |
| RF | UNRF |
| RT | UNRS |
| NS | UNS |
| BJ | USF |
| WW | WHITWORTH |
| WF | WHITWORTH PIPE, DIN 259 |
| WG | WHITWORTH PIPE, DIN 2999 |
| WP | WHITWORTH PIPE, DIN 3858 |
| WT | WHITWORTH SELECTED THREAD |
| WH | WHITWORTH STRAIGHT EXTERNAL PIPE, DIN 259 |
| WS | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 259 |
| WN | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 2999 |
| WB | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 3858 |
| WE | WHITWORTH TAPERED EXTERNAL PIPE, DIN 2999 |
| WA | WHITWORTH TAPERED EXTERNAL PIPE, DIN 3858 |
| WD | WOOD |
AHYM*JNOMINAL THREAD DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYMJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAO0)
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAM3)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAR)
| Table 1 |
| Reply Code (AA38) | Reply |
| ABD | A |
| ABP | ACROSS FACE |
| AAB | AT RIGHT ANGLE |
| AAX | AWAY FROM HOUSING |
| ABE | B |
| ACB | BACK |
| AAT | BACKWARD |
| ACC | BOW ASSEMBLY |
| ABF | C |
| ABG | CENTRAL |
| AAC | CLOCKWISE |
| AAD | COUNTERCLOCKWISE |
| ABH | D |
| AAE | DOWNWARD |
| ABJ | E |
| AAZ | EITHER DIRECTION |
| ABR | ELEVATING |
| ABZ | END |
| ACA | FLAT |
| AAW | FORWARD |
| ACD | FRONT |
| AAF | HORIZONTAL |
| ACE | INTERMEDIATE |
| ABS | LEFT |
| ABW | LEFT TO RIGHT |
| AAG | LEFT-HAND |
| ACF | LEFT-HAND INTERMEDIATE |
| ACG | LEFT-HAND LOWER |
| ACH | LEFT-HAND STRAIGHT |
| ABQ | LENGTHWISE |
| ABK | LOWER |
| AAH | NONDIRECTION |
| AAJ | PARALLEL |
| ABC | REVERSE |
| AAK | REVERSIBLE |
| ABT | RIGHT |
| ABX | RIGHT TO LEFT |
| AAL | RIGHT-HAND |
| ACJ | RIGHT-HAND INTERMEDIATE |
| ACK | RIGHT-HAND STRAIGHT |
| AAM | ROTATING |
| AAN | S |
| AAP | STRAIGHT |
| AAY | TOWARDS HOUSING |
| ABA | UNWINDING DIRECTION |
| ABL | UPPER |
| ACL | UPRIGHT |
| AAQ | UPWARD |
| AAR | VERTICAL |
| ABM | W |
| ABB | WINDING DIRECTION |
| ABN | X |
| AAS | Z |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJAA2.0*;AASAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ATPP*ASLOT QUANTITY
THE NUMBER OF SLOTS IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ATPPA10*)
WAQS*JSLOT WIDTH AND QUANTITY
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(WAQSJABBBG2.0*;WAQSJABBBG2.0$JABBBG2.0*;WAQSJABBBG2.0$$JABBBG2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AP65) | Reply |
| BBI | EIGHT SLOTS |
| BBF | FIVE SLOTS |
| BBE | FOUR SLOTS |
| BBJ | NINE SLOTS |
| BBB | ONE SLOT |
| BBH | SEVEN SLOTS |
| BBG | SIX SLOTS |
| BBK | TEN SLOTS |
| BBD | THREE SLOTS |
| BBC | TWO SLOTS |
LAQS*JSLOT LENGTH AND QUANTITY
THE DISTANCE MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(LAQSJLBBBH2.0*;LAQSJLBBBH2.0$JLBBBH2.0*;LAQSJLBBBH2.0$$JLBBBH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AP65) | Reply |
| BBI | EIGHT SLOTS |
| BBF | FIVE SLOTS |
| BBE | FOUR SLOTS |
| BBJ | NINE SLOTS |
| BBB | ONE SLOT |
| BBH | SEVEN SLOTS |
| BBG | SIX SLOTS |
| BBK | TEN SLOTS |
| BBD | THREE SLOTS |
| BBC | TWO SLOTS |
CSYX*JNOMINAL HOLE DIAMETER AND QUANTITY
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HOLE,AND TERMINATES AT THE CIRCUMFERENCE,AND THE NUMBER OF HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYXJAAAE2.0*;CSYXJAAAE2.0$JAAAE2.0*;CSYXJAAAE2.0$$JAAAE2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AP65) | Reply |
| AAH | EIGHT HOLES |
| AAE | FIVE HOLES |
| AAD | FOUR HOLES |
| AAJ | NINE HOLES |
| AAA | ONE HOLE |
| AAG | SEVEN HOLES |
| AAF | SIX HOLES |
| AAK | TEN HOLES |
| AAC | THREE HOLES |
| AAB | TWO HOLES |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information