This INC was converted from AEUSA to General Use on 8/3/2022.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED45406*)
CQCTDPRIMARY CONTAINER TYPE
INDICATES THE TYPE OF CONTAINER/S/ OR SUPPORTING DEVICE/S/ WHICH IS IN DIRECT CONTACT WITH THE ITEM.
Enter the applicable reply code from the table below
(CQCTDAAE*;CQCTDAGZ$DAAB*;CQCTDAGZ$$DAAB*)
| Table 1 |
| Reply Code (AN65) | Reply |
| AAB | AMPUL |
| AAC | AMPUL, COLOR BREAK |
| AAD | AMPUL, CRUSHABLE |
| AAE | AMPUL, NITROGEN-FILLED, FLAME SEALED |
| AAF | AMPUL, PRESCORED |
| AAG | AMPUL, SNAP-TOP |
| ADR | INJECTOR, AUTOMATIC |
| AGZ | SYRINGE-NEEDLE UNIT |
| AFQ | VIAL |
CRLKJPRIMARY CONTAINER CONTENT QUANTITY
A NUMERIC VALUE OF THE VOLUME,FORM,OR DOSAGE WITHIN EACH PRIMARY CONTAINER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRLKJML2.0*;CRLKJML2.0$JML2.0*)
| Table 1 |
| Reply Code (AN64) | Reply |
| CC | CUBIC CENTIMETERS |
| AB | LITERS AFTER RECONSTITUTION |
| MA | MICROGRAMS OF ACTIVE INGREDIENT |
| MG | MILLIGRAMS |
| MB | MILLIGRAMS OF ACTIVE INGREDIENT |
| ML | MILLILITERS |
| AC | MILLILITERS AFTER RECONSTITUTION |
CSGSDADMINISTRATION
THE AREA, ORIFICE, OR TISSUE OF THE BODY TO WHICH THE MEDICATION IS ADMINISTERED OR APPLIED BASED ON THE DRUG FORMULATION.
Enter the applicable reply code from the table below
(CSGSDCG*;CSGSDCB$DAA*;CSGSDCB$$DAA*)
| Table 1 |
| Reply Code (AG60) | Reply |
| AA | INJECTION |
| CB | INTRAMUSCULAR |
| CG | INTRATHECAL |
| CK | INTRAVENOUS |
| NA | NOT FOR INTRAVASCULAR USE |
| DM | SPINAL ANESTHESIA |
| DN | SUBCUTANEOUS |
AKJA*JACTIVE MEDICAMENT MEDICINAL STRENGTH
THE INGREDIENTS COMPOUNDED IN A PHARMACEUTICAL PREPARATION AND RECOGNIZED AS HAVING THERAPEUTIC VALUE/S/. /USUALLY REPRESENTATIVE IN THE ITEM NAME GENERIC NOMENCLATURE./
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKJAJGMA7029BW2.0*;AKJAJGMA7029BW2.0$$JGMA7029BW2.1*)
| Table 1 |
| Reply Code (AG53) | Reply |
| DR | DRAMS |
| FD | FLUID DRAMS |
| FN | FLUID OUNCES |
| GL | GALLONS |
| GR | GRAINS |
| GM | GRAMS |
| AM | INTERNATIONAL UNITS |
| KG | KILOGRAMS |
| LR | LITERS |
| UG | MICROGRAMS |
| MQ | MILLIEQUIVALENTS |
| MG | MILLIGRAMS |
| ML | MILLILITERS |
| AW | MILLIMOLES |
| MN | MINIMS |
| AL | NF UNITS |
| OZ | OUNCES |
| AT | PERCENTAGE, V/V |
| AS | PERCENTAGE, W/V |
| AR | PERCENTAGE, W/W |
| PT | PINTS |
| LB | POUNDS |
| PU | PRESSOR UNITS |
| QT | QUARTS |
| AJ | UNITS |
| AK | USP UNITS |
| Table 2 |
| Reply Code (AG54) | Reply |
| A0978 | APOMORPHINE HYDROCHLORIDE |
| A7014 | MORPHINE |
| A7029 | MORPHINE SULFATE |
| B2037 | MORPHINE SULFATE ANHYDROUS |
| A7030 | MORPHINE TARTRATE |
| Table 3 |
| Reply Code (AG55) | Reply |
| AB | ACTIVE INGREDIENT |
| DE | ACTIVE INGREDIENT PER ML |
| AP | BLANK |
| AQ | BY VOLUME |
| AR | BY WEIGHT |
| BZ | EQUIVALENT |
| AC | EQUIVALENT OF BASE |
| AF | EQUIVALENT OF BASE PER CUBIC CENTIMETER |
| AY | EQUIVALENT OF BASE PER CUBIC CENTIMETER OF RECONSTITUTED SOLUTION |
| AZ | EQUIVALENT OF BASE PER CUBIC CENTIMETER OF RECONSTITUTED SUSPENSION |
| BA | EQUIVALENT OF BASE PER GRAM |
| BC | EQUIVALENT OF BASE PER MICROGRAM |
| BB | EQUIVALENT OF BASE PER MILLIGRAM |
| BT | EQUIVALENT OF BASE PER MILLILITER |
| AD | EQUIVALENT OF COMPOUND |
| AH | EQUIVALENT OF COMPOUND PER CUBIC CENTIMETER |
| BD | EQUIVALENT OF COMPOUND PER CUBIC CENTIMETER OF RECONSTITUTED SUSPENSION |
| AJ | EQUIVALENT OF COMPOUND PER GRAM |
| BW | EQUIVALENT OF COMPOUND PER MILLILITER |
| AE | EQUIVALENT OF NEGATIVE RADICAL |
| AG | EQUIVALENT OF NEGATIVE RADICAL PER CUBIC CENTIMETER |
| BF | EQUIVALENT OF NEGATIVE RADICAL PER CUBIC CENTIMETER OF RECONSTITUTED SOLUTION |
| BG | EQUIVALENT OF NEGATIVE RADICAL PER CUBIC CENTIMETER OF RECONSTITUTED SUSPENSION |
| BR | EQUIVALENT OF NEGATIVE RADICAL PER GRAM |
| BE | EQUIVALENT OF NEGATIVE RADICAL PER MICROGRAM |
| BQ | EQUIVALENT OF NEGATIVE RADICAL PER MILLIGRAM |
| BX | EQUIVALENT OF NEGATIVE RADICAL PER MILLILITER |
| DD | EQUIVALENT PER 0.20 MILLILITERS |
| AA | EQUIVALENT PER 0.5 MILLILITERS |
| CS | EQUIVALENT PER 5 MILLILITERS |
| CT | EQUIVALENT PER 5 MILLILITERS OF RECONSTITUTED SOLUTION |
| CU | EQUIVALENT PER 5 MILLILITERS OF RECONSTITUTED SUSPENSION |
| CA | EQUIVALENT PER GRAM |
| CJ | EQUIVALENT PER LITER |
| CB | EQUIVALENT PER LITER OF RECONSTITUTED SOLUTION |
| CC | EQUIVALENT PER LITER OF RECONSTITUTED SUSPENSION |
| CD | EQUIVALENT PER MICROGRAM |
| CK | EQUIVALENT PER MILLIGRAM |
| CL | EQUIVALENT PER MILLILITER |
| CE | EQUIVALENT PER MILLILITER OF RECONSTITUTED SOLUTION |
| CF | EQUIVALENT PER MILLILITER OF RECONSTITUTED SUSPENSION |
| AV | EXTENDED RELEASE |
| AK | METRIC VOLUME |
| AU | PER 0.5 MILLILITERS |
| DF | PER 0.6 MILLILITERS |
| CZ | PER 10 OUNCES |
| DC | PER 100 MILLILITERS |
| CY | PER 15 MILLILITERS |
| DH | PER 2 MILLILITERS |
| DA | PER 20 CC |
| BV | PER 20 MILLILITERS |
| CX | PER 5 GRAMS |
| CM | PER 5 MILLILITERS |
| CQ | PER 5 MILLILITERS OF RECONSTITUTED SOLUTION |
| CR | PER 5 MILLILITERS OF RECONSTITUTED SUSPENSION |
| DG | PER 6.4 GRAMS |
| DB | PER CC |
| AL | PER CUBIC CENTIMETER |
| BH | PER CUBIC CENTIMETER OF RECONSTITUTED SOLUTION |
| BJ | PER CUBIC CENTIMETER OF RECONSTITUTED SUSPENSION |
| AW | PER CUBIC FEET |
| AS | PER CUBIC FOOT |
| AT | PER CUBIC INCH |
| AX | PER CUBIC METER |
| BN | PER FLUID OUNCE |
| BP | PER FLUIDRAM |
| BK | PER GRAM |
| BS | PER LITER |
| CN | PER METERED SPRAY |
| BM | PER MICROGRAM |
| BL | PER MILLIGRAM |
| BY | PER MILLILITER |
| CG | PER MILLILITER OF RECONSTITUTED SOLUTION |
| CH | PER MILLILITER OF RECONSTITUTED SUSPENSION |
| CP | PER OUNCE |
| BU | PERCENT |
| CV | RELEASED PER 24 HOURS |
| CW | RELEASED PER HOUR |
| AN | VOLUME PER CUBIC CENTIMETER |
| AM | VOLUME PER GRAM |
AKJQ*DPHARMACEUTICAL VEHICLE TYPE
THE LIQUID NONTOXIC COMPONENT FORM OF A PHARMACUETICAL PREPARATION WHICH NORMALLY HAS NO THERAPEUTIC ACTION,AND PRESENTS THE ACTIVE INGREDIENTS TO THE BODY FOR ABSORPTION.
Enter the applicable reply code from the table below
(AKJQDAZ*;AKJQDBK$DAD*;AKJQDBK$$DAD*)
| Table 1 |
| Reply Code (AG63) | Reply |
| AD | ALCOHOL |
| AP | ALCOHOLIC |
| AA | ANHYDROUS GLYCEROL |
| AB | AQUEOUS |
| AE | AROMATIC NAPHTHA |
| BA | CARBOXYMETHYLCELLULOSE |
| AV | CARBOXYMETHYLCELLULOSE SODIUM |
| BK | CELLULOSE MICROCRYSTALLINE |
| BD | CENTRIFUGED WHOLE BLOOD AND URINE |
| AQ | COLLODION BASE |
| BL | CORNSTARCH |
| BE | CRUDE OILS |
| AF | DIETHYLENE GLYCOL |
| BJ | ETHANOL |
| EA | ETHYL ALCOHOL |
| AR | FLUORINATED HYDROCARBON |
| BH | FORMAL GLYCEROL |
| BF | GAS AND AIR PARTICLES |
| AS | GLYCERIN |
| AT | HYDROALCOHOLIC |
| AG | ISOPROPANOL |
| BR | LACTOSE MONOHYDRATE |
| BP | MAGNESIUM STEARATE |
| AW | MINERAL OIL |
| AH | NAPHTHA |
| AC | NONAQUEOUS |
| AJ | NONTOXIC, FAST DRYING |
| AN | OIL |
| BB | OIL IN WATER EMULSION |
| AK | PETROLEUM NAPHTHA |
| PG | POLYETHYLENE GLYCOL |
| AX | POLYGLYCOL |
| BM | POVIDONE |
| PC | PROPYLENE CARBONATE |
| AY | PROPYLENE GLYCOL |
| BG | REFINED OILS |
| BC | SESAME OIL |
| AU | SODIUM CHLORIDE SOLUTION |
| BQ | SODIUM HYDROGENCARBONATE |
| BN | SODIUM LAURYL SULFATE |
| AZ | VEGETABLE OIL |
| AL | VOLATILE FLUORINE COMPOUND |
| AM | WATER |
| BS | WATER, PURIFIED |
CSCW*ATOTAL PRIMARY CONTAINER QUANTITY
THE NUMBER OF PRIMARY CONTAINERS WITHIN THE ITEM OF SUPPLY.
Enter the numeric reply with a minimum of one digit.
(CSCWA10*)
AJCN*DPROTECTIVE STORAGE FEATURE
THE PECULIAR STORAGE FEATURE/S/ REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(AJCNDAAJ*;AJCNDABA$DABN*;AJCNDABA$$DABN*)
| Table 1 |
| Reply Code (AA65) | Reply |
| ABX | ABRASION RESISTANT |
| ABU | ACCELERATED LIGHT |
| ABV | ACCELERATED OXYGEN |
| ABY | ACID RESISTANT |
| AAQ | ADHESIVE RESISTANT |
| ABZ | ALCOHOL RESISTANT |
| AAB | CHEMICAL RESISTANT |
| AAC | CORROSION RESISTANT |
| AAD | DRIPPROOF |
| AAF | DUST RESISTANT |
| AAE | DUSTPROOF |
| AAA | ELECTRICALLY INSULATED UP TO 1000 VOLTS |
| AFX | EXPIRATION DATED |
| AAG | EXPLOSION PROOF |
| AAJ | FIRE RESISTANT |
| AAH | FIREPROOF |
| AAU | FLUID RESISTANT |
| AAK | FUEL PROOF |
| AAL | FUEL RESISTANT |
| AAM | FUNGUS PROOF |
| AAN | FUNGUS RESISTANT |
| AAS | GASOLINE RESISTANT |
| AAP | HEAT RESISTANT |
| ABP | HUMIDITY PROOF |
| AAR | HUMIDITY RESISTANT |
| AAV | HYDROCARBON FUEL |
| AAT | MOISTURE PROOF |
| AAW | MOISTURE RESISTANT |
| AAX | OIL RESISTANT |
| AAY | OIL TIGHT |
| AAZ | PRESSURE PROOF |
| ABQ | SALT SPRAY RESISTANT |
| ABA | SALT WATER RESISTANT |
| ABB | SAND PROOF |
| ABC | SAND RESISTANT |
| ABD | SHOCK PROOF |
| ABE | SHOCK RESISTANT |
| ABF | SOLVENT RESISTANT |
| ABR | SPLASH PROOF |
| ABS | SPRAY PROOF |
| ABT | SPRAY TIGHT |
| ABW | SUBMERSIBLE |
| ABG | THERMAL SHOCK RESISTANT |
| ABH | VIBRATION PROOF |
| ABJ | VIBRATION RESISTANT |
| ABK | WATERPROOF |
| ABL | WATERTIGHT |
| ABN | WEATHER RESISTANT |
| ABM | WEATHERPROOF |
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information