An item composed of fiber, plastic foam, or synthetic material(s) in variousshapes and sizes. It is designed to reduce sound and/or provide resistance to the flow of heat. It may contain a vapor barrier or a fabric treated surface. It may include mounting holes.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED42144*)
IF STYLE/REPLY CODE(s) ALA000 WERE ENTERED FOR MRC MATT, YOU MUST ANSWER MRC (CBJL)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3BCLDRCA000*;MATT3BCLDRCA000$DSLK000*;MATT3BCLDRCA000$$DSLK000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3AHY | INSULATION |
| 3AYK | GASKET |
| 3BBL | COVER |
| 3BCI | FACING |
| 3BCJ | HOT SIDE |
| 3BCK | COLD SIDE |
| 3BCL | BACKING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3IEL | EDGING |
| Table 2 |
| Reply Code (MA01) | Reply |
| ZRW000 | ALUMINIZED FIBERGLASS |
| ZTC000 | ALUMINIZED SILICONE |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| ZSW000 | ALUMINUM FOIL |
| ZTA000 | CERAMIC FIBER |
| CCA000 | COTTON |
| ZRU000 | DOUGLAS FIR |
| FBX000 | FELT |
| FG0000 | FIBERGLASS |
| ZRR000 | FOAM |
| GSB000 | GLASS FIBER |
| ZRT000 | METALLIZED MYLAR |
| FBAC00 | MINERAL FIBER FOAM |
| PCA000 | PLASTIC |
| PCDB00 | PLASTIC CHLORINATED POLYVINYLCHLORIDE |
| PCCA00 | PLASTIC FOAM |
| PCCB00 | PLASTIC NYLON |
| PCW000 | PLASTIC POLYESTER |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCAP00 | PLASTIC VINYL |
| WDB000 | PLYWOOD |
| PCWA00 | POLYESTER FOAM |
| PCBS01 | POLYETHER FOAM |
| ZRS000 | POLYURETHANE BUTYL |
| ZRP000 | POLYURETHANE FOAM |
| RCAD00 | RUBBER BUTADIENE NITRILE |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0034 | RUBBER CARBOXYLIC-NITRILE-BUTADIENE CLASS XNBR |
| RCA000 | RUBBER NATURAL |
| RCAC00 | RUBBER NEOPRENE |
| RCAC01 | RUBBER NEOPRENE FOAM |
| RCB000 | RUBBER SYNTHETIC |
| SF0001 | SILICA FIBER |
| SLK000 | SILICONE |
| ZTB000 | SILICONE GLASS |
| ZRV000 | SILICONE SPONGE |
| STA000 | STEEL |
| ST0304 | STEEL COMP 304 |
| STB000 | STEEL CORROSION RESISTING |
| PCCP01 | VINYL NITRILE FOAM |
| WLA000 | WOOL |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
BZLX*DCORNER SHAPE
THE PHYSICAL CONFIGURATION OF THE CORNER.
Enter the applicable reply code from the table below
(BZLXDAA*;BZLXDBE$DAF*;BZLXDBE$$DAF*)
| Table 1 |
| Reply Code (AE88) | Reply |
| AA | BEVELED |
| AB | CHAMFERED |
| BE | CUT |
| AC | ROUND |
| AF | SQUARE |
BBJX*DMOUNTING POSITION
THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BBJXDACH*;BBJXDAFL$DABK*;BBJXDAFL$$DABK*)
| Table 1 |
| Reply Code (AM84) | Reply |
| ACT | BACK LEFT SIDE |
| ACU | BACK RIGHT SIDE |
| ACC | BODY FRONT |
| ACD | BODY REAR |
| ACE | BODY SIDE |
| ACF | BODY TOP |
| ACL | CAB |
| ACV | CONSOLE |
| ADG | DASHBOARD |
| AFM | EXTERIOR |
| ADJ | FLOOR |
| ABG | FRONT |
| AGR | HEADER |
| ACY | HEADLAMP |
| ADH | HEATER |
| AGM | INTAKE GRILL |
| AFL | INTERIOR |
| ACG | LEFT DOOR |
| ACH | LEFT FRONT |
| AAB | LEFT SIDE |
| AEM | MIDDLE |
| AGN | MUFFLER |
| ABK | REAR |
| ABV | REAR CARGO DOOR |
| ACJ | RIGHT DOOR |
| ACK | RIGHT FRONT |
| AAC | RIGHT SIDE |
| ADF | ROOF |
| ACM | SIDE PANEL |
| ACN | TOP |
| AAW | UNIVERSAL |
| AGQ | WATER PUMP |
| AGP | WHEEL WELL |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDAJF*;AXGYDBLP$DBAY*;AXGYDBLP$$DBAY*)
| Table 1 |
| Reply Code (AM39) | Reply |
| BDH | ADHESIVE |
| BLQ | ADHESIVE TAPE |
| ACR | FLANGE |
| BAY | FOIL TAPE |
| ACK | HOOK AND PILE TAPE |
| AAL | MOUNTING SLOTS |
| BLP | MOUNTING STRIP |
| ADC | PRESS FIT |
| CAE | PRESSURE SENSITIVE ADHESIVE |
| AJF | SNAP FASTENER(S) |
| ANC | SNAP-ON |
| ANK | STRIP |
| AAZ | UNTHREADED MOUNTING HOLES |
ARJA*JPRESSURE RATING
THE PRESSURE AT WHICH AN ITEM IS RATED TO OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARJAJL2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| L | KILOPASCALS |
| S | MEGAPASCALS |
| R | NEWTONS PER SQUARE MILLIMETER |
| G | POUNDS PER SQUARE INCH GAGE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPCY000*;SFTTDZNP000$DANA000*;SFTTDZNP000$$DANA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| MSB000 | ADHESIVE |
| ANA000 | ANODIZE |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| PNA000 | PAINT |
| PCA000 | PLASTIC |
| PCA001 | PLASTIC POLYUREA |
| PCY000 | PLASTIC POLYURETHANE |
| PRA000 | PRIMER |
| SLA000 | SILICON |
| ZNP000 | TEXTURED |
BDNL*JNOISE REDUCTION COEFFICIENT RATING
THE MEASURED RATING OF THE NOISE REDUCTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDNLJB2.0*;BDNLJB2.0$JB2.0*;BDNLJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ALUB*DFLEXIBLE CELLULAR MATERIAL TYPE
THE TYPE OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056.
Enter the applicable reply code from the table below
(ALUBDAA)
| Table 1 |
| Reply Code (AP01) | Reply |
| AA | TYPE 1 - OPEN CELL |
| AU | TYPE 2 - CLOSED CELL |
ASCB*DINSULATION DEGREE
THE EXTENT OF THE INSULATION USED ON THE ITEM.
Enter the applicable reply code from the table below
(ASCBDAB)
| Table 1 |
| Reply Code (AL70) | Reply |
| AB | FULLY INSULATED |
| AF | PARTIALLY INSULATED |
ALUC*DFLEXIBLE CELLULAR MATERIAL CLASS
THE CLASS OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056.
Enter the applicable reply code from the table below
(ALUCDBL)
| Table 1 |
| Reply Code (AP01) | Reply |
| BU | CLASS 1 |
| AV | CLASS A - NON-OIL RESISTANT |
| BK | CLASS B - OIL RESISTANT, LOW SWELL |
| BL | CLASS C - OIL RESISTANT, MEDIUM SWELL |
| BM | CLASS D - EXTREME TEMPERATURE RESISTANT |
AMHB*ALAYER QUANTITY
THE NUMBER OF LAYERS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AMHBA10*)
ABJH*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
ALUD*DFLEXIBLE CELLULAR MATERIAL GRADE
THE GRADE OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056. THE GRADE RATING REPRESENTS THE COMPRESSION DEFLECTION OR THE AMOUNT OF FORCE IN POUNDS PER SQUARE INCH TO DEFLECT THE SAMPLE 25 PER CENT OF ITS HEIGHT.
Enter the applicable reply code from the table below
(ALUDDBV)
| Table 1 |
| Reply Code (AP01) | Reply |
| BN | GRADE 0 - LESS THAN 2 PSI |
| BP | GRADE 1 - 2-5 PSI |
| BQ | GRADE 2 - 5-9 PSI |
| BR | GRADE 3 - 9-13 PSI (FOR CLASSES A, B, C) 9-15 PSI (FOR CLASS D) |
| BS | GRADE 4 - 13-17 PSI (FOR CLASSES A, B, C) 15-22 PSI (FOR CLASS D) |
| BT | GRADE 5 - 17-25 PSI (FOR CLASSES A, B, C) 22-30 PSI (FOR CLASS D) |
| BV | GRADE C |
BDPC*DLAYER ENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE LAYER IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(BDPCDAAJ*;BDPCDAAP$DACH*;BDPCDAAP$$DACH*)
| Table 1 |
| Reply Code (AA65) | Reply |
| AAJ | FIRE RESISTANT |
| AAP | HEAT RESISTANT |
| ME | NONTOXIC |
| ACH | WATER REPELLENT |
CQFM*JHARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQFMJSBA2.0*;CQFMJSBA2.0$JSBA2.0*;CQFMJSBA2.0$$JSBA2.1*)
| Table 1 |
| Reply Code (AC26) | Reply |
| SR | SHORE DUROMETER |
| SA | SHORE DUROMETER A |
| SM | SHORE DUROMETER A-2 |
| SB | SHORE DUROMETER B |
| SE | SHORE DUROMETER C |
| SD | SHORE DUROMETER D |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AACR*DPRIMARY USE DESIGNATION
AN INDICATION OF WHETHER THE ITEM/S/ ARE PRIMARILY DESIGNED FOR USE ON GROUND EQUIPMENT OR FOR USE ON OTHER THAN GROUND EQUIPMENT.
Enter the applicable reply code from the table below
(AACRDE*;AACRDF$DD*;AACRDF$$DD*)
| Table 1 |
| Reply Code (AA23) | Reply |
| E | ACOUSTICAL |
| D | HEAT |
| F | UNIVERSAL |
CWFR*JNOMINAL OVERALL LENGTH
THE NOMINAL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWFRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ABMKJOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$JAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CMZC*DCOVERING LOCATION
INDICATES THE LOCATION OF AN ITEM TO WHICH THE COVERING HAS BEEN APPLIED.
Enter the applicable reply code from the table below
(CMZCDDGG*;CMZCDBRA$DBRB*;CMZCDBRA$$DBRB*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| DGF | INNER |
| DGG | OUTER |
| BRA | PORT |
| BRB | STARBOARD |
BDNZ*JDENSITY RATING
AN INDICATION OF THE RATED DENSITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDNZJCM2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| CQ | GALLONS PER MINUTE |
| CR | LITERS PER MINUTE |
| DA | POUNDS PER CUBIC FOOT |
| CM | POUNDS PER INCH |
| CW | POUNDS PER SQUARE FOOT |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAC2.0*;ADUMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SHPE*DSHAPE
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(SHPEDAHS*;SHPEDZU$DASW*;SHPEDZU$$DASW*)
| Table 1 |
| Reply Code (AD07) | Reply |
| ABS | CIRCULAR |
| ZU | CIRCULAR,CONCAVE |
| AFC | FLAT |
| AHS | HORIZONTAL OVAL |
| AHT | HORIZONTAL RECTANGULAR |
| AJG | IRREGULAR |
| BMX | L-SHAPE |
| AKR | OBLONG |
| ALC | OVAL |
| AND | RECTANGULAR |
| ANN | RECTANGULAR W/ROUNDED CORNERS |
| APL | ROUND |
| AQF | ROUND W/FLATTED SIDES |
| ASL | SQUARE |
| AVX | SQUARE W/CUT CORNERS |
| ASW | SQUARE W/ROUNDED CORNERS |
| AVW | SQUARE W/SQUARED CORNERS |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDBL0000*;HUESDGR0000$$DGR0011*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BL0190 | BLACK,CHARCOAL |
| MS0015 | CHARCOAL |
| GY0007 | GRAY, CHARCOAL |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| GR0494 | GREEN, 383 |
| GR0011 | GREEN, OLIVE |
| MA0000 | MAROON |
| BR0192 | MOJAVE BROWN |
| MS0062 | SAND, DESERT |
| MS0413 | SEAFOAM GREEN |
| TA0000 | TAN |
| WH0000 | WHITE |
AECS*ABOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AECSA10*)
CTKH*JTENSILE STRENGTH
THE GREATEST LONGITUDINAL STRESS AN ITEM CAN BEAR WITHOUT TEARING APART PER UNIT OF MEASURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTKHJJG2.0*)
| Table 1 |
| Reply Code (AJ20) | Reply |
| JG | KILOPASCALS |
| JK | MEGAPASCALS |
| DQ | POUNDS PER SQUARE INCH |
CYHX*AVEHICLE DESIGN CONTROL ACTIVITY
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VEHICLE.
Enter the alpha-numeric reply with five character(s) exactly.
(CYHXAU7N0I)
CYHY*AVEHICLE IDENTIFICATION DESIGNATOR
THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC VEHICLE.
Enter the alpha-numeric reply with a minimum of one character.
(CYHYAN3)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDDYJ*;CBBLDBLM$$DDYJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BLM | HEAT SHIELD |
| DYJ | MOUNTING SLOTS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
AARQ*DFLAMMABILITY RATING
THE EXTENT TO WHICH THE MATERIAL WILL SUPPORT COMBUSTION /EXCLUDES ALL OUTER COVERINGS/.
Enter the applicable reply code from the table below
(AARQDE)
| Table 1 |
| Reply Code (AA64) | Reply |
| C | COMBUSTIBLE |
| D | INCOMBUSTIBLE |
| E | SELF-EXTINGUISHING, FIRE RETARDANT |
| F | SLOW-BURNING |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
IF STYLE/REPLY CODE(s) NU WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (ALAX)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDJG*;ENACDNR$$DNU*)
| Table 1 |
| Reply Code (EN02) | Reply |
| JG | ASBESTOS ALTERNATIVE PRODUCTS |
| NU | PACKING AND INSULATING MATERIALS - BIOBASED |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
ALAX*BBIOBASED CONTENT PERCENTAGE
THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALAXB2.0)
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJLB2.0*;ABTBJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBJL*DMATERIAL TYPE
INDICATES THE TYPE OF MATERIAL COMPOSING THE ITEM.
Enter the applicable reply code from the table below
(CBJLDABFB)
| Table 1 |
| Reply Code (AN48) | Reply |
| ABFB | FOIL |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAK2)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information