A rigid item of various shapes designed to aligin or restain filters or filtering elements used in fluid/air purification systems.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED40307*)
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMKJOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJLC2.0*;ABMKJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDZSJ001*;MATTDSTF000$DFEJ000*;MATTDSTF000$$DFEJ000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL0045 | ALUMINUM ALLOY 355.0 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL6061 | ALUMINUM ALLOY 6061 |
| ZSJ001 | ALUMINUM ALLOY 6061, TYPE 6 |
| ZSM000 | ALUMINUM ALLOY 6063, T-52 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| ZSR000 | ALUMINUM ALLOY, 356-T6 |
| FBZ000 | CANVAS |
| CUB000 | COPPER ALLOY |
| FEJ000 | IRON DUCTILE |
| FEC000 | IRON MALLEABLE |
| PCA000 | PLASTIC |
| STA000 | STEEL |
| ST1020 | STEEL COMP 1020 |
| ST1035 | STEEL COMP 1035 |
| ST1040 | STEEL COMP 1040 |
| STB000 | STEEL CORROSION RESISTING |
| STF000 | STEEL,CARBON |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJLC2.0*;ABKWJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDMS0339*;HUESDTA0099$DTA0000*;HUESDTA0099$$DTA0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| MS0339 | CAMOUFLAGE, WOODLAND |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| GR0024 | GREEN, FOREST |
| MS0363 | STONE, LIGHT |
| TA0000 | TAN |
| TA0099 | TAN, 686A |
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJLA2.0*;ADAVJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SHPE*DSHAPE
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(SHPEDADK*;SHPEDASL$DBBX*;SHPEDASL$$DBBX*)
| Table 1 |
| Reply Code (AD07) | Reply |
| ACY | CURVED |
| BNM | CURVED L |
| BBX | CURVED-U- |
| ADK | HALF CIRCLE |
| BNN | I SHAPED |
| AJG | IRREGULAR |
| AND | RECTANGULAR |
| ANN | RECTANGULAR W/ROUNDED CORNERS |
| ASL | SQUARE |
| AVW | SQUARE W/SQUARED CORNERS |
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJNCPTEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AAH | 1ST CONNECTOR |
| AFA | 1ST HOLE |
| AAJ | 2ND CONNECTOR |
| AFB | 2ND HOLE |
| AAK | 3RD CONNECTOR |
| AFC | 3RD HOLE |
| AAL | 4TH CONNECTOR |
| AFD | 4TH HOLE |
| AAM | 5TH CONNECTOR |
| AFE | 5TH HOLE |
| AAN | 6TH CONNECTOR |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| ACR | ABRASIVE |
| ABB | ABSORBER |
| ACL | AIR TANK |
| AAG | ALL CONNECTORS |
| AEN | ALL ENDS |
| AHL | ALL HOLES |
| ASF | ALL SURFACES |
| XEE | AXIALLY AT EACH END |
| XNE | AXIALLY AT ONE END |
| BAK | BACK |
| BCR | BACK CORNER |
| ACQ | BACKING |
| BLB | BALL BEARING |
| BLE | BALL END |
| ABD | BALL STOP |
| BAL | BALLAST |
| BND | BAND |
| BSE | BASE |
| BRG | BEARING |
| BLD | BLADE |
| BRD | BOARD |
| BDY | BODY |
| BDL | BODY LINING |
| BLT | BOLT |
| BBF | BOTH BEARING FLATS |
| BEN | BOTH ENDS |
| BSD | BOTH SIDES |
| BTL | BOTTLE |
| BTM | BOTTOM |
| BAE | BOTTOM AT ONE END |
| BBG | BOTTOM BEARING |
| BNP | BOTTOM INSIDE PERIPHERY |
| BPP | BOTTOM OUTSIDE PERIPHERY |
| BWL | BOWL |
| BRA | BRAID |
| BZR | BRAZING RING |
| ACD | BUCKLE |
| BSH | BUSHING |
| BTT | BUTT |
| BED | BUTT END |
| AAU | CANNULA |
| CAP | CAP |
| CSE | CASE |
| CNR | CENTER |
| BYE | CENTER LEFT SIDE |
| CSD | CENTER STUD |
| CNL | CENTRAL |
| CHN | CHAIN |
| CHB | CHAMBER |
| CMR | CHAMFER |
| CFN | CHAMFERED END |
| CLM | CLAMP |
| ABE | CLEANING WIRE |
| CDS | COATED SIDE |
| CLR | COLLAR |
| CCH | CONCENTRIC HOLE |
| CAC | CONDUCTOR ACCOMMODATION |
| CTK | CONTACT |
| CTN | CONTACT END |
| CTB | COUNTERBORE |
| CBN | COUNTERBORE END |
| CBF | COUNTERBORE FACE |
| CBW | COUNTERBORE WALL |
| CKN | COUNTERSUNK END |
| CVR | COVER |
| CUP | CUP |
| DME | DOME |
| ELW | ELBOW |
| ETM | ELECTRICAL TERMINATION |
| NND | END |
| ACE | END CLIP |
| NPC | END OPPOSITE CONTACT |
| NPP | END OPPOSITE POINT |
| EXP | EXPANDER |
| EXT | EXTERNAL |
| FAC | FACE |
| FMT | FACE MAT |
| FPL | FACE PLATE |
| FTH | FIFTH DISCHARGE |
| FFN | FIFTH INTAKE |
| FFP | FIFTH STEP |
| FTR | FILTER |
| FNG | FINGER |
| FCB | FIRST COUNTERBORE |
| FDS | FIRST DISCHARGE |
| FEN | FIRST END |
| FNT | FIRST INTAKE |
| FSL | FIRST LEG |
| FST | FIRST STEP |
| FTP | FIRST THREADED PORTION |
| ABG | FITTED STYLET |
| FLG | FLANGE |
| FLC | FLOW CONTROL DEVICE |
| FLR | FOLLOWER RING |
| FRD | FOURTH DISCHARGE |
| HEN | FOURTH END |
| FHN | FOURTH INTAKE |
| FSP | FOURTH STEP |
| ABC | FRAME |
| FRN | FRONT |
| FCR | FRONT CORNER |
| ACN | GAGE |
| GKT | GASKET |
| GRP | GRIP |
| ACT | GROMMET |
| GRZ | GROOVE |
| GND | GROOVED END |
| HNG | HANDGRIP |
| HNL | HANDLE |
| ABH | HEAD |
| HED | HEAD |
| HBS | HEAD BEARING SURFACE |
| HAD | HEAD OUTSIDE DIAMETER |
| HTP | HEAD TOP |
| HBD | HEADBAND |
| HEL | HEEL |
| HHL | HIGH HEEL |
| HDR | HOLDER |
| ACF | HOOK |
| HZB | HORIZONTAL BAR |
| HZR | HORIZONTALLY THROUGH RING |
| HSG | HOUSING |
| ABJ | HUB |
| LDD | ILLUMINATION DIRECTIVE DEVICE |
| NNR | INNER |
| ABK | INNER CANNULA |
| ABL | INNER CANNULA KNOB |
| NLR | INNER LAYER |
| ABM | INNER NEEDLE |
| NSE | INNER SHELL |
| NCP | INSCRIPTION |
| NBG | INSCRIPTION BACKGROUND |
| NSR | INSERT |
| AAB | INSIDE |
| NEB | INSIDE EXCEPT BOTTOM |
| NSH | INSIDE HOUSING |
| NLB | INSIDE LEFT BREAST |
| NLC | INSIDE LEFT CORNER |
| NPF | INSIDE PERIPHERY |
| NRB | INSIDE RIGHT BREAST |
| NRC | INSIDE RIGHT CORNER |
| NSB | INSULATED BARREL |
| NSC | INSULATED COMPLETELY |
| NSD | INSULATED HANDLE |
| NSW | INSULATED WIRE LEAD TERMINALS |
| NSL | INSULATION |
| NST | INSULATOR |
| NML | INTERMEDIATE LAYER |
| NTE | INTERNAL |
| ABN | INTRODUCER KNOB |
| JWE | JAW |
| JNT | JOINT |
| ACG | KEEPER |
| LEN | LARGE END |
| LSK | LARGE SHANK |
| LBF | LARGEST BEARING FLAT |
| LAP | LARGEST OUTSIDE PERIPHERY |
| LBT | LEFT BREAST |
| LEW | LEFT ELBOW |
| LFC | LEFT FACE |
| LPL | LEFT PULSE |
| LSR | LEFT SHOULDER |
| LSE | LEFT SIDE |
| LSL | LEFT SLEEVE |
| LSG | LEFT SLING |
| LWT | LEFT WRIST |
| LHN | LEFT-HAND |
| LHB | LEFT-HAND BOTTOM |
| LHS | LEFT-HAND SIDE |
| LHT | LEFT-HAND TOP |
| LNZ | LENS |
| LNR | LINER |
| LLG | LINER LINING |
| LNG | LINING |
| LBS | LINING, BOTH SIDES |
| LWS | LINING, ONE SIDE |
| LGN | LONG END |
| LGS | LONG SHANK |
| LSN | LONG SHANK END |
| ACH | LOOP |
| LHL | LOW HEEL |
| LLF | LOWER LEFT FRONT |
| LRF | LOWER RIGHT FRONT |
| MBY | MAIN BODY |
| ACP | MANIFOLD |
| ABP | MIDDLE CANNULA |
| MTB | MOUNTING BASE |
| MTE | MOUNTING END |
| MTF | MOUNTING FACILITY |
| MTH | MOUTH |
| NEL | NEEDLE |
| NPL | NIPPLE |
| NUT | NUT |
| AAT | OBTURATOR |
| ABQ | OBTURATOR KNOB |
| ABR | OBTURATOR ROD |
| FCN | OFF CENTER |
| WBF | ONE BEARING FLAT |
| NEN | ONE END |
| WSE | ONE SIDE |
| PEN | OPERATIVE END |
| AAZ | OPERATIVE ENDS |
| ABF | OPPOSITE BEARING FLAT |
| AGE | OPPOSITE GROOVED END |
| AHE | OPPOSITE HEAD END |
| AHP | OPPOSITE POINTS |
| ATE | OPPOSITE THREADED END |
| TRS | OTHER SIDE |
| ATR | OUTER |
| ABS | OUTER CANNULA |
| ALR | OUTER LAYER |
| ASE | OUTER SHELL |
| AAC | OUTSIDE |
| ASD | OUTSIDE DIAMETER |
| AEB | OUTSIDE EXCEPT BOTTOM |
| AHG | OUTSIDE HOUSING |
| ALC | OUTSIDE LEFT CORNER |
| APF | OUTSIDE PERIPHERY |
| ARC | OUTSIDE RIGHT CORNER |
| AAR | OVAL END |
| AAD | OVERALL |
| AAP | OVERALL EXCEPT INSULATION |
| PCK | PACKING |
| ABU | PIN |
| AAX | PLATE |
| PLG | PLUG |
| PLY | PLY |
| PDN | POINTED END |
| PRT | PORT SIDE |
| BDP | PROBE BODY |
| PLS | PULLEY SURFACE |
| AAY | RACK |
| RAN | RADIUS END |
| RER | REAR |
| RFT | REFLECTOR |
| RWR | RESISTANCE WIRE |
| RWS | RESISTANCE WIRE EMBEDDING/SUPPORT INSULATION |
| RBT | RIGHT BREAST |
| REW | RIGHT ELBOW |
| RFC | RIGHT FACE |
| RPL | RIGHT PULSE |
| RSR | RIGHT SHOULDER |
| RSE | RIGHT SIDE |
| RSL | RIGHT SLEEVE |
| RSG | RIGHT SLING |
| RWT | RIGHT WRIST |
| RHN | RIGHT-HAND |
| RHB | RIGHT-HAND BOTTOM |
| RHS | RIGHT-HAND SIDE |
| RHT | RIGHT-HAND TOP |
| ACJ | RING |
| RAD | ROD |
| RND | ROUND END |
| SCW | SCREW |
| SRF | SEAL REINFORCEMENT |
| ACS | SEAT |
| SET | SEAT |
| SCB | SECOND COUNTERBORE |
| SDS | SECOND DISCHARGE |
| SEN | SECOND END |
| SCN | SECOND INTAKE |
| SLG | SECOND LEG |
| SSP | SECOND STEP |
| SEP | SECOND THREADED PORTION |
| SGD | SECURING DEVICE |
| ABV | SECURITY STOP |
| SND | SEVENTH DISCHARGE |
| SFT | SHAFT |
| SNK | SHANK |
| SKB | SHANK BOTTOM |
| SKN | SHANK END |
| SNS | SHANK SHEATH |
| ABW | SHEATH |
| STH | SHEATH |
| SHL | SHELL |
| SLD | SHIELD |
| SSN | SHORT SHANK END |
| SDR | SHOULDER |
| SRN | SHOULDER END |
| SRH | SHOULDER HARNESS |
| SRS | SHOULDER STRAP |
| SYD | SIDE |
| SDW | SIDEWALL |
| AAF | SINGLE CONNECTOR |
| SGG | SINGLE DISCHARGE |
| SNN | SINGLE END |
| SNH | SINGLE HOLE |
| SLN | SINGLE INTAKE |
| STP | SINGLE THREADED PORTION |
| SHD | SIXTH DISCHARGE |
| SXN | SIXTH INTAKE |
| SLE | SLEEVE |
| STE | SLOT END |
| SCF | SMALL CHAMFER |
| SMN | SMALL END |
| SBF | SMALLEST BEARING FLAT |
| SAP | SMALLEST OUTSIDE PERIPHERY |
| SKT | SOCKET |
| SZL | SOLE |
| SPR | SPRING |
| ABX | SPRING CLIP |
| SQN | SQUARE END |
| STN | STAND |
| STB | STARBOARD SIDE |
| STM | STEM |
| AAW | STICK |
| ACK | STRAP |
| STK | STRIKE |
| STD | STUD |
| AAV | STYLET |
| ABY | STYLET KNOB |
| ABZ | STYLET WIRE |
| TLP | TAILPIECE |
| ABA | TANG |
| ACA | TAPERED CANNULA |
| TED | TAPERED END |
| TML | TERMINALS |
| TDD | THIRD DISCHARGE |
| TEN | THIRD END |
| TNT | THIRD INTAKE |
| TSP | THIRD STEP |
| TTP | THIRD THREADED PORTION |
| TNS | THREAD INSERT |
| TDP | THREAD PIECE |
| THN | THREADED END |
| THD | THREADS |
| TPT | TIP |
| TPR | TIP INSERTS |
| TNG | TONGUE |
| TPE | TOP |
| TNN | TOP AT ONE END |
| TBG | TOP BEARING |
| TNP | TOP INSIDE PERIPHERY |
| TPP | TOP OUTSIDE PERIPHERY |
| TPS | TOP SURFACE |
| TRD | TREAD |
| ACB | TROCAR |
| TRN | TRUNNION |
| TBE | TUBE |
| CTS | UNCOATED SIDE |
| NHD | UNDER HEAD |
| AAS | UNDERCUT |
| AAE | UNION |
| NTN | UNTHREADED END |
| APR | UPPER |
| ACM | VALVE |
| AAQ | VERTICALLY THROUGH RING |
| VAL | VIAL |
| ACC | WIRE TWISTER |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAE1)
CQBC*JMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJKTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| S | MEGAPASCALS |
| N | NEWTONS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
CQHQ*JMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQHQJN2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| S | MEGAPASCALS |
| N | NEWTONS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
AWLS*DCONNECTION TYPE
INDICATES THE TYPE OF CONNECTION/S/.
Enter the applicable reply code from the table below
(AWLSDPB*;AWLSDLA$DXU*;AWLSDLA$$DXU*)
| Table 1 |
| Reply Code (AB76) | Reply |
| QZ | 5 FOOT DRAINAGE TUBE |
| CJ | ADAPTER TUBE TO HOSE |
| SB | ADJUSTABLE FLANGE |
| DN | ADJUSTABLE THREADED ADAPTER |
| MB | AIR |
| RG | AIR CHUCK QUICK DISCONNECT |
| GS | ANGLE |
| GT | ARM W/LOCKING PIN |
| DD | AUTOMATIC COUPLER |
| PC | BALL STUD |
| BL | BAND COUPLER |
| AAA | BANDED |
| GW | BAR W/CHAIN |
| CM | BARBED |
| MA | BAYONET JOINT |
| PX | BEADED |
| RD | BELL MOUTH |
| TE | BEVELED, PLAIN |
| SM | BINDING POST |
| SK | BOSS |
| SC | BRACKET |
| GX | BRACKET W/BOLT |
| PN | BRAZED |
| AAM | BRAZING, PIPE |
| AAN | BRAZING, TUBE |
| LX | BULB |
| PJ | BULBOUS |
| CD | BULKHEAD |
| DF | BUTT |
| AN | BUTT WELD |
| AAP | BUTT WELD PIPE |
| AAQ | BUTT WELD TUBE |
| KL | BUTTON HEAD NOZZLE |
| FT | CALKED |
| NT | CAM LOCKING QUICK DISCONNECT |
| FP | CIRCULAR CLAMP-ON |
| DY | CIRCUMFERENTIALLY GROOVED |
| GY | CLAMP |
| LM | CLAY PIPE SPIGOT |
| ACP | CLEVIS |
| GZ | CLEVIS W/BOLT |
| HA | CLEVIS W/LOCKING PIN |
| HB | CLEVIS W/PIPE PIN |
| HC | CLEVIS W/WELD |
| ABE | CLOSED |
| ABF | COLLAR |
| BM | COMPANION FLANGE UNION |
| AAJ | COMPRESSED GAS ASSOCIATION |
| KJ | COMPRESSIBLE TIP, JET NOZZLE |
| ACQ | CONCAVE |
| PT | CONE POINT END |
| MD | CONNECTING LINK |
| WK | CONNECTOR, PLUG |
| ACR | CONVEX |
| BQ | COPPER TUBE |
| BR | COPPER TUBING, ENDS SEALED |
| ACU | COUPLING |
| RX | COUPLING HALF, QUICK DISCONNECT, EXTERNAL |
| NW | COUPLING HALF, QUICK DISCONNECT, INTERNAL |
| SD | COUPLING NUT |
| SX | CRIMPED |
| HD | CROSS BAR |
| PU | CYLINDRICAL END |
| LA | DIN COUPLER |
| HE | DOUBLE EYE HOOK |
| DG | DOUBLE MORTISE TENON |
| HF | DOUBLE SPRING LOCK HOOK |
| LY | DOUBLE SWIVEL |
| CW | DRAIN |
| FQ | DRILLED |
| EB | DRILLED FLANGE |
| HG | DRILLED PLATE |
| FF | DUAL PANEL JACK |
| EZ | ELASTIC TUBING |
| LZ | EXPANSION RING |
| ED | EXTERNAL |
| NR | EXTERNAL BUTT WELD |
| EG | EXTERNAL NPTF PIPE |
| EF | EXTERNAL PIPE |
| GF | EXTERNAL PIPE THREAD |
| AZ | EXTERNAL QUICK DISCONNECT |
| ABH | EXTERNAL SPLINE |
| EH | EXTERNAL TAPER PIPE THREAD |
| RW | EXTERNAL UNTHREADED |
| SY | EXTERNAL, SEAT OR GASKET SEAL |
| HH | EYE |
| HJ | EYE BOLT |
| HK | EYE CLEVIS |
| HL | EYE HOOK |
| HM | EYE HOOK W/LOCKING PIN |
| HN | EYE PLATE |
| HP | EYE W/LOCKING PIN |
| MK | FEMALE BRAZING NIPPLE |
| ML | FEMALE IRON PIPE |
| QD | FEMALE QUICK DISCONNECT UNIT |
| GG | FEMALE TAPERED PIPE THREADED |
| GH | FEMALE TAPERED THREADED |
| PY | FEMALE THREAD |
| PZ | FEMALE THREAD ADAPTER TO HOSE |
| QA | FEMALE THREAD HOSE |
| QB | FEMALE THREAD SYRINGE |
| QC | FEMALE THREAD UNIT |
| GJ | FEMALE THREADED |
| SA | FEMALE TUBE CONNECTOR |
| DE | FIFTH WHEEL UPPER PLATE W/KINGPIN |
| EJ | FITTING END |
| ACV | FLANGE |
| BS | FLANGE UNION |
| ACS | FLANGE W/BAIL |
| HQ | FLANGE W/HOLE |
| XX | FLANGE, OVAL W/HOLES |
| XY | FLANGE, OVAL W/O HOLES |
| AAR | FLANGE, RECTANGULAR W/HOLES |
| AAS | FLANGE, RECTANGULAR W/O HOLES |
| AAT | FLANGE, ROUND W/HOLES |
| AAU | FLANGE, ROUND W/O HOLES |
| XV | FLANGE, SQUARE W/HOLES |
| XW | FLANGE, SQUARE W/O HOLES |
| AAD | FLANGED |
| SW | FLANGED PIPE |
| BT | FLANGED, ENDS SEALED |
| SZ | FLANGED, PLAIN |
| TA | FLANGED, RAISED |
| TB | FLANGED, RAISED, W/COUNTERBORE |
| TC | FLANGED, RECESSED |
| CG | FLARE |
| BW | FLARE TUBE |
| EK | FLARE TUBE FITTING |
| EL | FLARE TUBE PRESSURE FITTING |
| MC | FLUID |
| EM | FLUID PRESSURE FITTING |
| KM | FLUSH NOZZLE |
| HR | FORK W/HOOK |
| HS | FORK W/LOCKING PIN |
| JD | FORKED 1077 W/LOCKING PIN |
| HT | FORKED BOLTED TO TAILGATE |
| HW | FORKED LOCKING PIN |
| HX | FORKED W/LOCK CHAIN |
| HY | FORKED W/LOCK PIN |
| JB | FORKED W/LOCKING ADAPTER |
| HZ | FORKED W/LOCKING HOOK |
| JA | FORKED W/LOCKING PIN |
| RQ | FORKED W/LOCKING PLATES |
| JC | FORKED W/LOCKING SCREW |
| AAE | FREE OUTLET |
| QE | FRICTION UNIT |
| JE | FRONT BUMPER ATTACHING PROVISION |
| MT | GASKET SEAL |
| BA | GLAD HAND QUICK DISCONNECT |
| ABJ | GROOVED |
| GQ | GROOVED COUPLING |
| MG | GROOVED FACE FLANGE |
| TD | GROOVED INSIDE |
| MM | GROUND JOINT FEMALE BRAZING TAILPIECE W/UNION NUT |
| MN | GROUND JOINT FEMALE TAILPIECE W/UNION NUT |
| MF | GROUND JOINT TAILPIECE W/UNION NUT |
| WW | GROUND TERMINAL |
| JF | HANDLE MANUAL TOWING |
| JG | HOLE |
| JH | HOOK |
| JJ | HOOK W/LOCKING PIN |
| RR | HOOK W/SPRING LOCK |
| DM | HOSE |
| NK | HOSE FITTING THREAD |
| PF | HOSE NIPPLE |
| QS | HOSE PUSH-ON TYPE |
| ACY | HUB |
| LT | HUB |
| XA | HUB, BORED |
| XB | HUB, ROUGH STOCK |
| XC | HUB, SOLID |
| ABS | HUB,BORED |
| ABT | HUB,HEX BORE |
| ABU | HUB,INVOLUTE SPLINE |
| ABV | HUB,SOLID |
| ABW | HUB,SQUARE BORE |
| ABX | HUB,STRAIGHT SPLINE |
| ABY | HUB,TAPERED BORE |
| KP | HYDRAULIC |
| KN | HYDRAULIC COUPLER |
| KQ | HYDRAULIC NOZZLE |
| CX | INLET |
| LQ | INSERTED FROM INSIDE RIM |
| LR | INSERTED FROM OUTSIDE RIM |
| FA | INTEGRAL CABLE W/AUDIO PLUG |
| FB | INTEGRAL CABLE W/COAXIAL PLUG |
| FC | INTEGRAL CABLE W/POWER PLUG |
| FD | INTEGRAL CORD W/POWER PLUG |
| GA | INTEGRAL FLANGE |
| WH | INTEGRAL KEY |
| WJ | INTEGRAL KEY WITH INTEGRAL KEYWAY |
| BN | INTERNAL |
| EN | INTERNAL PIPE |
| GE | INTERNAL PIPE THREAD |
| AY | INTERNAL QUICK DISCONNECT |
| NS | INTERNAL SOLDER |
| ABK | INTERNAL SPLINE |
| EP | INTERNAL STRAIGHT THREAD |
| LN | IRON PIPE SIZE |
| SE | JAM NUT |
| ABL | KEYED |
| WQ | KEYWAY |
| DH | LAP |
| KS | LARGE BUTTON HEAD |
| KR | LARGE BUTTON HEAD COUPLER |
| KT | LARGE BUTTON HEAD NOZZLE |
| JK | LOCKING PIN |
| SL | LUBRICATION FITTING |
| FY | LUG |
| JL | LUNETTE EYE |
| RS | LUNETTE W/LOCKING PIN |
| QY | MALE ADAPTER TUBE |
| MP | MALE BRAZING NIPPLE |
| QF | MALE CORRUGATED |
| GK | MALE HOSE ADAPTER |
| MQ | MALE IRON PIPE |
| GL | MALE TAPERED THREADED |
| QG | MALE THREAD |
| QH | MALE THREAD HOSE TO ADAPTER |
| QJ | MALE THREAD SYRINGE |
| QK | MALE THREAD SYRINGE HOSE |
| QL | MALE THREAD UNIT |
| GM | MALE UNTHREADED |
| EX | METAL TUBING |
| KX | MOGUL DOT |
| KW | MOGUL DOT COUPLER |
| KY | MOGUL DOT NOZZLE |
| DJ | MORTISE |
| ME | MOUNTING BRACKET |
| PG | MOUNTING FLANGE |
| AAF | MUFFLED OUTLET |
| CK | NEEDLE |
| KZ | NEEDLE NOZZLE |
| EQ | NIPPLE |
| DP | NONADJUSTABLE CONNECTOR |
| GN | NPT BRASS MALE END |
| WL | OFFSET FROM STEM |
| ABG | OPEN |
| ABM | OPEN END SLOT |
| DR | OPEN SIDE SLOT |
| CY | OUTLET |
| JM | PIN |
| LB | PIN NOZZLE |
| WP | PIN TERMINAL |
| JN | PINTLE HOOK |
| BX | PIPE |
| NL | PIPE FITTING THREAD |
| GD | PIPE THREAD |
| FR | PIVOT ARM |
| JP | PIVOT BLOCK |
| ABN | PLAIN |
| SF | PLAIN CLAMP |
| PR | PLAIN CYLINDRICAL |
| DZ | PLAIN FERRULE |
| PB | PLAIN FLANGE |
| LC | PLAIN NOZZLE |
| PD | PLAIN THREADED |
| SG | PLAIN UNTHREADED |
| EY | PLASTIC TUBING |
| SN | PLUG |
| ACW | PREFORMED |
| FM | PRESSURIZED COAXIAL PLUG |
| FN | PRESSURIZED COAXIAL SOCKET |
| FL | PRINTED CIRCUIT |
| EE | PUNCTURING PIN |
| ACL | PUSH IN |
| LD | PUSH NOZZLE |
| QM | PUSH-ON UNIT |
| QQ | QUICK CONNECT SYRINGE |
| LS | QUICK COUPLING |
| GC | QUICK DISCONNECT FITTING |
| QR | QUICK DISCONNECT UNIT |
| PV | RADIUS END |
| AL | RAISED FACE FLANGE |
| SP | RECEPTACLE CONNECTOR |
| FG | RECEPTACLE, AUDIO |
| FH | RECEPTACLE, COAXIAL |
| FJ | RECEPTACLE, POWER |
| AK | RECESSED FLANGE |
| DS | RECTANGULAR HOLE |
| TF | REDUCED SOCKET W/ONE BRAZING RING |
| MW | REGULAR FLARE |
| MH | RIGID |
| JQ | RING |
| JR | RING DRAWBAR COUPLER |
| ER | RING SEALED HOLE |
| DT | ROUND HOLE |
| DA | ROUNDED |
| QN | RUBBER PRESSURE FITTING ADAPTER TO MOUTHPIECE |
| JS | S HOOK |
| RA | SCREW PLUG |
| FS | SERRATED |
| LW | SHAFT |
| ACE | SHAFT, PLAIN |
| ACC | SHAFT, SLIP FIT |
| ACD | SHAFT, STEPPED |
| ACB | SHAFT, THREADED |
| ACA | SHAFT,INVOLUTE SPLINE |
| ABZ | SHAFT,STRAIGHT SPLINE |
| EA | SHOULDERED FERRULE |
| LE | SHUT OFF JET NOZZLE |
| GB | SIL-BRAZED |
| NN | SILVER BRAZING |
| FE | SINGLE PANEL JACK |
| BK | SLEEVE |
| WM | SLIDING UNION |
| FW | SLIP |
| JT | SLIP HOOK W/LOCKING BAR |
| QP | SLIP-ON UNIT |
| ACM | SLOTTED |
| DB | SLOTTED HEAD |
| DW | SLOTTED HOLE |
| DC | SLOTTED PIN |
| SH | SLOTTED SWIVEL NUT |
| PK | SMOOTH |
| CL | SNAP-ON |
| PE | SOCKET |
| TG | SOCKET W/FLARE |
| MR | SOCKET WELDING |
| AAV | SOCKET, WELD, PIPE |
| AAW | SOCKET, WELD, TUBE |
| ACX | SOFT |
| LP | SOIL PIPE HUB |
| NM | SOLDER |
| RN | SOLDER LUG |
| SQ | SOLDER STUD |
| AAX | SOLDER, TUBE |
| BB | SPLIT CLAMP |
| WN | SPLIT FLANGE |
| LF | SPRAY NOZZLE |
| JW | SPREAD W/LOCKING PIN |
| DK | SQUARE END |
| LH | STANDARD BUTTON HEAD |
| LG | STANDARD BUTTON HEAD COUPLER |
| PW | STANDARD BUTTON HEAD NOZZLE |
| LK | STANDARD DOT |
| LJ | STANDARD DOT COUPLER |
| LL | STANDARD DOT NOZZLE |
| RB | STANDARD GROUND GLASS SOCKET |
| ES | STRAIGHT FEMALE |
| JX | STRAIGHT HOOK |
| JY | STRAIGHT W/BOLT |
| NY | STRAIGHT-KEYED |
| TH | STREAMLINED, W/ONE BRAZING RING |
| TJ | STREAMLINED, W/TWO BRAZING RINGS |
| SR | STUD |
| BU | SURFACE MOUNT |
| BZ | SWEAT FLANGE |
| PP | SWEAT SOLDER |
| FX | SWEATED |
| BY | SWEATED TUBE |
| GR | SWING JOINT |
| XP | SWITCHED |
| MJ | SWIVEL |
| PS | TAPERED FOR INSERTION INTO RUBBER STOPPER |
| PL | TAPERED, SERRATED |
| NZ | TAPERED-KEYED |
| CP | TAPPED HOLE |
| DL | TENON |
| FK | TERMINAL BLOCK W/SCREW |
| SS | TERMINAL LUG |
| ST | TERMINAL STUD |
| CA | THREAD |
| RP | THREAD ADAPTER |
| AAG | THREADED |
| ET | THREADED 18-15 MM INTERNATIONAL METRIC FINE |
| WY | THREADED CARTRIDGE |
| ABP | THREADED EXTERNAL |
| AAY | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| WR | THREADED EXTERNAL GAS FITTING |
| AAZ | THREADED EXTERNAL HOSE |
| RM | THREADED EXTERNAL HOSE GRIPPING |
| AAK | THREADED EXTERNAL PIPE |
| ABA | THREADED EXTERNAL TUBE |
| ACH | THREADED EXTERNAL, COMPRESSION |
| ACJ | THREADED EXTERNAL, FLARED |
| ACK | THREADED EXTERNAL, FLARELESS |
| TN | THREADED EXTERNAL, GASKET SEAL |
| TP | THREADED EXTERNAL, HOSE GRIPPING NIPPLE |
| TQ | THREADED EXTERNAL, INVERTED FLARE |
| TR | THREADED EXTERNAL, PLAIN |
| TS | THREADED EXTERNAL, SWIVEL NUT INVERTED FLARE |
| CS | THREADED FEMALE |
| NA | THREADED FEMALE TUBE |
| MX | THREADED FEMALE, COMPRESSION |
| MY | THREADED FEMALE, GASKET SEAL |
| MZ | THREADED FEMALE, INVERTED FLARE |
| RZ | THREADED FLARE TUBE |
| DX | THREADED HOLE |
| ABQ | THREADED INTERNAL |
| RL | THREADED INTERNAL AND EXTERNAL PIPE |
| RH | THREADED INTERNAL AND EXTERNAL TUBE |
| ABB | THREADED INTERNAL BOSS |
| NX | THREADED INTERNAL COUPLING |
| AT | THREADED INTERNAL GAS CYLINDER |
| WS | THREADED INTERNAL GAS FITTING |
| ABC | THREADED INTERNAL HOSE |
| AAL | THREADED INTERNAL PIPE |
| RK | THREADED INTERNAL PIPE AND EXTERNAL TUBE |
| XR | THREADED INTERNAL SWIVEL |
| ABD | THREADED INTERNAL TUBE |
| RJ | THREADED INTERNAL TUBE AND EXTERNAL PIPE |
| TT | THREADED INTERNAL, DOUBLE COMPRESSION |
| TW | THREADED INTERNAL, DRAINAGE |
| TX | THREADED INTERNAL, FLARE |
| TY | THREADED INTERNAL, GASKET SEAL |
| TZ | THREADED INTERNAL, INVERTED FLARE |
| WA | THREADED INTERNAL, PLAIN |
| WB | THREADED INTERNAL, SWIVEL NUT W/COMPRESSION SLEEVE |
| WF | THREADED INTERNAL, SWIVEL NUT W/INTEGRAL CLINCH SLEEVE |
| WG | THREADED INTERNAL, SWIVEL NUT W/LOOSE CLINCH SLEEVE |
| WC | THREADED INTERNAL, SWIVEL NUT, FLARE |
| WD | THREADED INTERNAL, SWIVEL NUT, FLARELESS |
| WE | THREADED INTERNAL, SWIVEL NUT, INVERTED FLARE |
| CT | THREADED MALE |
| NH | THREADED MALE TUBE |
| NB | THREADED MALE, BULKHEAD |
| NC | THREADED MALE, COMPRESSION |
| ND | THREADED MALE, FLARELESS TUBE |
| NE | THREADED MALE, GASKET SEAL |
| NF | THREADED MALE, REGULAR FLARE |
| NG | THREADED MALE, TAPERED PIPE |
| CB | THREADED PIPE |
| CQ | THREADED ROD |
| YA | THREADED SLIP JOINT |
| SJ | THREADED UNION |
| ABR | TONGUE |
| JZ | TONGUE W/LOCKING PIN |
| KA | TOWING LUG |
| KB | TOWING RING |
| CC | TUBE |
| EW | TUBE 1/4 IN. OD |
| RY | TUBE COUPLING NUT |
| NP | TUBE FITTING THREAD |
| FZ | TUBE THROUGH CENTER |
| ACN | TWIST IN |
| EC | UNDRILLED FLANGE |
| PM | UNIFORM DIA, SERRATED |
| BP | UNION |
| MS | UNION END |
| PH | UNION FERRULE |
| KC | UNIVERSAL FORKED |
| XD | UNIVERSAL JOINT |
| RF | UNIVERSAL QUICK DISCONNECT |
| XQ | UNSWITCHED |
| BH | UNTHREADED |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| XS | UNTHREADED EXTERNAL HOSE, BARBED |
| XT | UNTHREADED EXTERNAL HOSE, BEADED |
| XU | UNTHREADED EXTERNAL HOSE, PLAIN |
| AJ | UNTHREADED EXTERNAL PIPE |
| AAB | UNTHREADED EXTERNAL PIPE/TUBE |
| ACT | UNTHREADED EXTERNAL TUBE |
| AD | UNTHREADED EXTERNAL TUBE |
| NJ | UNTHREADED FEMALE |
| WV | UNTHREADED FLUID PASSAGE BOLT |
| PQ | UNTHREADED HOLE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AAC | UNTHREADED INTERNAL PIPE/TUBE |
| AB | UNTHREADED INTERNAL TUBE |
| RE | UNTHREADED PIPE |
| AX | UNTHREADED PIPE OR TUBE |
| WX | UNTHREADED TUBE |
| WT | UNTHREADED TUBE W/FORMED END |
| BC | UNTHREADED UNIVERSAL FITTING BOLT END |
| KH | W/LOCKING PIN |
| AAH | WELDED |
| KD | WELDED EYE |
| KE | WELDED SHACKLE |
| XZ | WIRE |
| RC | WIRE LEAD TERMINALS |
| ACG | YOKE |
| KF | YOKE W/LATCH ASSEMBLY |
| KG | YOKE W/LOCKING PIN |
| RT | YOKE W/SPRING LOADED LOCKING PINS |
| ACF | YOKE, WITH SPIDER |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDDM*;THSDDAF$DNM*;THSDDAF$$DNM*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AC | ACME C |
| AG | ACME G |
| MM | ACME-MODIFIED |
| MS | ACME-SPECIAL |
| AS | AMERICAN STANDARD |
| MP | AMPT |
| AN | ANPT |
| AU | ANSFH |
| PA | API |
| PB | API IF |
| RE | API REG |
| PC | API STANDARD |
| AP | APSC |
| GA | ARMOURED CONDUIT, DIN 40430 |
| AW | ASA |
| BM | ASA HOSE |
| AV | ASH |
| BA | BA |
| RZ | BRASS |
| CJ | BRITISH NONSTANDARD WHITFORM |
| DP | BRITISH STANDARD BUTTRESS |
| CY | BRITISH STANDARD CYCLE THREAD |
| CQ | BS CON |
| BF | BSF |
| ZP | BSP. L |
| DQ | BSP.C |
| FB | BSP.F |
| BE | BSP.F EXT |
| BT | BSP.F INT |
| PL | BSP.PL |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BP | BSP.TR |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| TP | BSTP |
| BW | BSW |
| TT | BUTTRESS |
| CS | CALIF STANDARD |
| CH | CHEMICAL HOSE |
| DW | COARSE |
| CT | CUTTING |
| DD | DARDALET |
| DE | DEVILBISS |
| DF | DEVILBISS STANDARD |
| DM | DISSYMMETRICAL PROFILE NF L05-420 |
| DS | DOUBLE STUB |
| DR | DRIVE |
| CL | EF |
| FN | FINE |
| FM | FORMING |
| FP | F-PTF |
| DX | FRENCH CONDUIT THREAD NF C68-190 |
| GE | G |
| CM | INTERNATIONAL METRIC FINE THREAD |
| AD | INTERNATIONAL SPECIAL |
| AR | INTERNATIONAL STANDARD |
| AE | IPS |
| CR | ISO FINE THREAD PITCH SERIES 1 |
| CW | ISO FINE THREAD PITCH SERIES 2 |
| CX | ISO FINE THREAD PITCH SERIES 3 |
| CZ | ISO FINE THREAD PITCH SERIES 4 |
| SY | ISO FORM |
| SM | ISO M |
| ME | ISO METRIC FINE |
| SS | ISO S |
| JL | JIC |
| LH | LOWENHERZ |
| EM | M |
| CN | METRIC |
| MN | METRIC NONSTD |
| MX | METRIC TAPERED EXTERNAL |
| MB | METRIC TAPERED EXTERNAL, DIN 158 |
| MJ | MJ |
| MF | MODIFIED ACME 2G |
| MA | MODIFIED AMERICAN NATIONAL STANDARD STRAIGHT PIPE |
| CA | N |
| NX | N 5 |
| AB | N ACME BOX |
| AX | N SPECIAL |
| BZ | N STD |
| EN | N-12 |
| YN | N-16 |
| ZN | N-2 |
| NA | N-3 ACME |
| NB | N-4 STANDARD |
| DN | NATIONAL GAS ASSOCIATION |
| BX | NC |
| CE | NC-2 |
| NY | NC-2X |
| NL | NCT |
| NQ | NEF |
| ET | NET |
| BY | NF |
| CB | NF-1 |
| CC | NF-2 |
| FS | NFS |
| NG | NGO |
| GS | NGS |
| GT | NGT |
| AF | NGTD |
| AH | NGTI |
| AJ | NGTP |
| NH | NH |
| NZ | NH-SPCL |
| NK | NONSTANDARD ROUND |
| BB | NONSTANDARD SPECIAL |
| PN | NP |
| PG | NPI |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| AK | NPSN |
| NP | NPT |
| AL | NPTA |
| NT | NPTF |
| PR | NPT-MODIFIED |
| TR | NPTR |
| TS | NPTS |
| AQ | NS |
| SN | NS-2 |
| NW | NSPT |
| PK | PACIFIC COAST |
| LN | PL INT BS61 |
| PW | PT |
| PH | PTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| RR | R |
| RH | RAN HOSE |
| RL | RL |
| LB | RL(BSPL) |
| RD | ROUND |
| RJ | ROUND, DIN 20400 |
| RG | ROUND, DIN 405 |
| RM | ROUND, DIN 70156 |
| RK | ROUND, DIN 7272 |
| RP | RPT |
| RS | RS |
| SW | SAE |
| LT | SAE-LT |
| SG | SGT |
| SJ | SI |
| DA | SI FINE THREAD PITCH SERIES 1 |
| DB | SI FINE THREAD PITCH SERIES 2 |
| DC | SI FINE THREAD PITCH SERIES 3 |
| DJ | SI FINE THREAD PITCH SERIES 4 |
| DK | SI FINE THREAD PITCH SERIES 5 |
| SX | SI FORM |
| SK | SI-M |
| AY | SPECIAL |
| AZ | SPECIAL ACME |
| CF | SPECIAL MODIFIED WHITWORTH |
| PQ | SPT |
| SQ | SQUARE |
| SD | STANDARD ACME DOUBLE LEAD |
| ST | STD STUB ACME |
| CP | STEWART WARNER SPECIAL |
| SR | STI |
| SA | STUB ACME |
| SZ | STUB ACME DOUBLE LEAD |
| SE | STUB ACME M1 |
| SB | STUB ACME M2 |
| MT | SUBMARINE THD |
| TD | TAPER DRIVE |
| EX | TR EXT BS61 |
| RN | TR INT BS61 |
| TZ | TRAPEZIUM |
| AT | TWPP |
| UN | UN |
| NR | UN FORM |
| FF | UN-12 |
| FG | UN-16 |
| ZA | UN-20 |
| ZB | UN-28 |
| ZC | UN-32 |
| FC | UN-4 |
| FD | UN-6 |
| FE | UN-8 |
| NC | UNC |
| DL | UNC DOUBLE LEAD |
| DG | UND |
| BK | UNDERWRITERS |
| CG | UNDERWRITERS STANDARD TIP |
| NE | UNEF |
| DH | UNEF-2A |
| YM | UNEF-MODIFIED |
| NF | UNF |
| MD | UNF-MODIFIED |
| BD | UNG |
| BQ | UNIFIED |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NM | UNM |
| ND | UN-MODIFIED |
| HR | UNR |
| RC | UNRC |
| RF | UNRF |
| RT | UNRS |
| NS | UNS |
| BJ | USF |
| WW | WHITWORTH |
| WF | WHITWORTH PIPE, DIN 259 |
| WG | WHITWORTH PIPE, DIN 2999 |
| WP | WHITWORTH PIPE, DIN 3858 |
| WT | WHITWORTH SELECTED THREAD |
| WH | WHITWORTH STRAIGHT EXTERNAL PIPE, DIN 259 |
| WS | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 259 |
| WN | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 2999 |
| WB | WHITWORTH STRAIGHT INTERNAL PIPE, DIN 3858 |
| WE | WHITWORTH TAPERED EXTERNAL PIPE, DIN 2999 |
| WA | WHITWORTH TAPERED EXTERNAL PIPE, DIN 3858 |
| WD | WOOD |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDAAA001*;SFTTDAAA002$DCMA000*;SFTTDAAA002$$DCMA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| AAA002 | CHEMICAL |
| CMA000 | CHROMATE |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PCY000 | PLASTIC POLYURETHANE |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| PRA001 | PRIMER EPOXY-LEAD AND CHROMIUM FREE |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ATPP*ASLOT QUANTITY
THE NUMBER OF SLOTS IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ATPPA10*)
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAA2.0*;ABGCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGD*JSLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGDJLA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACUN*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM. THIS MRC IS BEING DISCONTINUED. PLEASE USE MRC AXGY IF AVAILABLE.
Enter the applicable reply code from the table below
(ACUNDACJ*;ACUNDADA$DAPT*;ACUNDADA$$DAPT*)
| Table 1 |
| Reply Code (AB89) | Reply |
| APP | BOLTED |
| ADA | FLANGE |
| APT | HINGED |
| AAH | RIVETED |
| ACJ | SCREW |
ACHY*DMOUNTING HOLE TYPE
INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(ACHYDP*;ACHYDE$DC*;ACHYDE$$DC*)
| Table 1 |
| Reply Code (AB68) | Reply |
| A | COUNTERBORED |
| B | COUNTERSUNK |
| C | PLAIN |
| P | SLOTTED |
| D | THREADED |
| U | THRU HOLE |
| E | UNTHREADED |
CSYX*JNOMINAL HOLE DIAMETER AND QUANTITY
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HOLE,AND TERMINATES AT THE CIRCUMFERENCE,AND THE NUMBER OF HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYXJAAAP2.0*;CSYXJAAAP2.0$$JAAAP2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AP65) | Reply |
| AAH | EIGHT HOLES |
| AAT | EIGHTEEN HOLES |
| AAL | ELEVEN HOLES |
| AAQ | FIFTEEN HOLES |
| AAE | FIVE HOLES |
| AAD | FOUR HOLES |
| AAP | FOURTEEN HOLES |
| AAJ | NINE HOLES |
| AAU | NINETEEN HOLES |
| AAA | ONE HOLE |
| AAG | SEVEN HOLES |
| AAS | SEVENTEEN HOLES |
| AAF | SIX HOLES |
| AAR | SIXTEEN HOLES |
| AAK | TEN HOLES |
| AAN | THIRTEEN HOLES |
| ABL | THIRTY FIVE HOLES |
| ABK | THIRTY FOUR HOLES |
| ABF | THIRTY HOLES |
| ABG | THIRTY ONE HOLES |
| ABM | THIRTY SIX HOLES |
| ABJ | THIRTY THREE HOLES |
| ABH | THIRTY TWO HOLES |
| AAC | THREE HOLES |
| AAM | TWELVE HOLES |
| ABD | TWENTY EIGHT HOLES |
| AAZ | TWENTY FOUR HOLES |
| AAV | TWENTY HOLES |
| ABE | TWENTY NINE HOLES |
| AAW | TWENTY ONE HOLES |
| ABC | TWENTY SEVEN HOLES |
| ABB | TWENTY SIX HOLES |
| AAY | TWENTY THREE HOLES |
| AAX | TWENTY TWO HOLES |
| AAB | TWO HOLES |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJLA2.0*;ABNMJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAH6)
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDTT*;HEATDCX$DJR*;HEATDCX$$DJR*)
| Table 1 |
| Reply Code (AD05) | Reply |
| CR | COLD DRAWN |
| CX | COLD ROLLED |
| CU | EXTRUDED |
| EX | H-111 STRAIN HARDENED |
| AV | H-112 AS ROLLED |
| GB | H-116 SPECIALLY TREATED |
| TP | H-24 STRAIN HARDENED, PARTIALLY ANNEALED TO 1/2 HARD |
| TQ | H-32 STRAIN HARDENED, STABILIZED TO 1/4 HARD |
| QP | H-321 STRAIN HARDENED |
| QQ | H-323 STRAIN HARDENED |
| TR | H-34 STRAIN HARDENED, STABILIZED TO 1/2 HARD |
| TS | H-36 STRAIN HARDENED, STABILIZED TO 3/4 HARD |
| TT | H-38 STRAIN HARDENED, STABILIZED TO FULL HARD |
| CH | HARD |
| CY | HARDENED |
| CT | HOT ROLLED |
| JR | OILED |
| JQ | PICKLED |
| EN | QUENCHED |
| JT | ROLLED |
| EP | TEMPERED |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information