A standoff, internally and/or externally, threaded on both ends with a hinge or pivot point to allow for independent movement of the ends.
expandFSC Information
5340Hardware, Commercial
expandColloquial Information
No Colloquials assigned to this Approve Item Name at this time
expandChange List
ISAC Reply 3AEE added to MRC MATT.
ISAC Reply 3ETG added to MRC MATT.
ISAC Reply 3HOU added to MRC MATT.
ISAC Reply 1A deleted from MRC MATT.
ISAC Reply 1B deleted from MRC MATT.
ISAC Reply 1C deleted from MRC MATT.
ISAC Reply 3AEE added to MRC MDCL.
ISAC Reply 3ETG added to MRC MDCL.
ISAC Reply 3HOU added to MRC MDCL.
ISAC Reply 1A deleted from MRC MDCL.
ISAC Reply 1B deleted from MRC MDCL.
ISAC Reply 1C deleted from MRC MDCL.
ISAC Reply 3AEE added to MRC SFTT.
ISAC Reply 3HOU added to MRC SFTT.
ISAC Reply 1A deleted from MRC SFTT.
ISAC Reply 1B deleted from MRC SFTT.
ISAC Reply 1C deleted from MRC SFTT.
ISAC Reply 3AEE added to MRC STDC.
ISAC Reply 3HOU added to MRC STDC.
ISAC Reply 1A deleted from MRC STDC.
ISAC Reply 1B deleted from MRC STDC.
ISAC Reply 1C deleted from MRC STDC.
ISAC Reply 3AEE added to MRC THSD.
ISAC Reply 3ETH added to MRC THSD.
ISAC Reply 3ETI added to MRC THSD.
ISAC Reply 3ETJ added to MRC THSD.
ISAC Reply 3ETK added to MRC THSD.
ISAC Reply 3ETL added to MRC THSD.
ISAC Reply 3HOU added to MRC THSD.
ISAC Reply 1A deleted from MRC THSD.
ISAC Reply 1B deleted from MRC THSD.
ISAC Reply 1C deleted from MRC THSD.
ISAC Reply 1D deleted from MRC THSD.
ISAC Reply 1E deleted from MRC THSD.
ISAC Reply 1F deleted from MRC THSD.
ISAC Reply 3AEE added to MRC CQJX.
ISAC Reply 3ETH added to MRC CQJX.
ISAC Reply 3ETI added to MRC CQJX.
ISAC Reply 3ETJ added to MRC CQJX.
ISAC Reply 3ETK added to MRC CQJX.
ISAC Reply 3ETL added to MRC CQJX.
ISAC Reply 3HOU added to MRC CQJX.
ISAC Reply 1A deleted from MRC CQJX.
ISAC Reply 1B deleted from MRC CQJX.
ISAC Reply 1C deleted from MRC CQJX.
ISAC Reply 1D deleted from MRC CQJX.
ISAC Reply 1E deleted from MRC CQJX.
ISAC Reply 1F deleted from MRC CQJX.
ISAC Reply 3AEE added to MRC CMLP.
ISAC Reply 3ETH added to MRC CMLP.
ISAC Reply 3ETI added to MRC CMLP.
ISAC Reply 3ETK added to MRC CMLP.
ISAC Reply 3HOU added to MRC CMLP.
ISAC Reply 1A deleted from MRC CMLP.
ISAC Reply 1B deleted from MRC CMLP.
ISAC Reply 1C deleted from MRC CMLP.
ISAC Reply 1D deleted from MRC CMLP.
ISAC Reply 1E deleted from MRC CMLP.
ISAC Reply 1F deleted from MRC CMLP.
ISAC Reply 3AEE added to MRC CQQR.
ISAC Reply 3ETI added to MRC CQQR.
ISAC Reply 3HOU added to MRC CQQR.
ISAC Reply 1A deleted from MRC CQQR.
ISAC Reply 1B deleted from MRC CQQR.
ISAC Reply 1C deleted from MRC CQQR.
ISAC Reply 1D deleted from MRC CQQR.
ISAC Reply 1E deleted from MRC CQQR.
ISAC Reply 1F deleted from MRC CQQR.
ISAC Reply 3AEE added to MRC AAJD.
ISAC Reply 3ETH added to MRC AAJD.
ISAC Reply 3ETI added to MRC AAJD.
ISAC Reply 3ETK added to MRC AAJD.
ISAC Reply 3HOU added to MRC AAJD.
ISAC Reply 1A deleted from MRC AAJD.
ISAC Reply 1B deleted from MRC AAJD.
ISAC Reply 1C deleted from MRC AAJD.
ISAC Reply 1D deleted from MRC AAJD.
ISAC Reply 1E deleted from MRC AAJD.
ISAC Reply 1F deleted from MRC AAJD.
ISAC Reply 3AEE added to MRC AAJE.
ISAC Reply 3ETI added to MRC AAJE.
ISAC Reply 3HOU added to MRC AAJE.
ISAC Reply 1A deleted from MRC AAJE.
ISAC Reply 1B deleted from MRC AAJE.
ISAC Reply 1C deleted from MRC AAJE.
ISAC Reply 1D deleted from MRC AAJE.
ISAC Reply 1E deleted from MRC AAJE.
ISAC Reply 1F deleted from MRC AAJE.
ISAC Reply 3AEE added to MRC AAJF.
ISAC Reply 3ETH added to MRC AAJF.
ISAC Reply 3ETI added to MRC AAJF.
ISAC Reply 3ETJ added to MRC AAJF.
ISAC Reply 3ETK added to MRC AAJF.
ISAC Reply 3ETL added to MRC AAJF.
ISAC Reply 3HOU added to MRC AAJF.
ISAC Reply 1A deleted from MRC AAJF.
ISAC Reply 1B deleted from MRC AAJF.
ISAC Reply 1C deleted from MRC AAJF.
ISAC Reply 1D deleted from MRC AAJF.
ISAC Reply 1E deleted from MRC AAJF.
ISAC Reply 1F deleted from MRC AAJF.
ISAC Reply 3AEE added to MRC AASA.
ISAC Reply 3ETH added to MRC AASA.
ISAC Reply 3ETI added to MRC AASA.
ISAC Reply 3ETJ added to MRC AASA.
ISAC Reply 3ETK added to MRC AASA.
ISAC Reply 3ETL added to MRC AASA.
ISAC Reply 3HOU added to MRC AASA.
ISAC Reply 1A deleted from MRC AASA.
ISAC Reply 1B deleted from MRC AASA.
ISAC Reply 1C deleted from MRC AASA.
ISAC Reply 1D deleted from MRC AASA.
ISAC Reply 1E deleted from MRC AASA.
ISAC Reply 1F deleted from MRC AASA.
MRC CTTC has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED40277*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3ETGDST0028*;MATT3ETGDST0028$DAL2024*;MATT3ETGDST0028$$DAL2024*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETGSTANDOFF
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (MA01)Reply
ALA000ALUMINUM
ALB000ALUMINUM ALLOY
AL1100ALUMINUM ALLOY 1100
AL1230ALUMINUM ALLOY 1230
AL2011ALUMINUM ALLOY 2011
AL2014ALUMINUM ALLOY 2014
AL2017ALUMINUM ALLOY 2017
AL2024ALUMINUM ALLOY 2024
AL3003ALUMINUM ALLOY 3003
AL5052ALUMINUM ALLOY 5052
AL5083ALUMINUM ALLOY 5083
AL5086ALUMINUM ALLOY 5086
AL5154ALUMINUM ALLOY 5154
AL5454ALUMINUM ALLOY 5454
AL6061ALUMINUM ALLOY 6061
AL6062ALUMINUM ALLOY 6062
AL6063ALUMINUM ALLOY 6063
AL6262ALUMINUM ALLOY 6262
AL7075ALUMINUM ALLOY 7075
AL0109ALUMINUM ALLOY A380.1
CUA000COPPER
CUB000COPPER ALLOY
CU0249COPPER ALLOY 102
CU0286COPPER ALLOY 104
CU0287COPPER ALLOY 105
CU0288COPPER ALLOY 107
CU0063COPPER ALLOY 110
CU0290COPPER ALLOY 114
CU0291COPPER ALLOY 116
CU0247COPPER ALLOY 120
CU0323COPPER ALLOY 121
CU0248COPPER ALLOY 122
CU0292COPPER ALLOY 123
CU0278COPPER ALLOY 125
CU0324COPPER ALLOY 127
CU0326COPPER ALLOY 128
CU0315COPPER ALLOY 130
CU0279COPPER ALLOY 142
CU0069COPPER ALLOY 172
CU0265COPPER ALLOY 175
CU0264COPPER ALLOY 220
CU0074COPPER ALLOY 230
CU0076COPPER ALLOY 240
CU0079COPPER ALLOY 260
CU0304COPPER ALLOY 262
CU0080COPPER ALLOY 268
CU0081COPPER ALLOY 270
CU0272COPPER ALLOY 272
CU0274COPPER ALLOY 274
CU0302COPPER ALLOY 280
CU0330COPPER ALLOY 330
CU0305COPPER ALLOY 331
CU0332COPPER ALLOY 332
CU0335COPPER ALLOY 335
CU0340COPPER ALLOY 340
CU0088COPPER ALLOY 342
CU0306COPPER ALLOY 344
CU0307COPPER ALLOY 345
CU0308COPPER ALLOY 347
CU0309COPPER ALLOY 348
CU0310COPPER ALLOY 350
CU0089COPPER ALLOY 353
CU0090COPPER ALLOY 356
CU0091COPPER ALLOY 360
CU0370COPPER ALLOY 370
CU0092COPPER ALLOY 377
CU0098COPPER ALLOY 462
CU0099COPPER ALLOY 464
CU0465COPPER ALLOY 465
CU0466COPPER ALLOY 466
CU0467COPPER ALLOY 467
CU0100COPPER ALLOY 482
CU0101COPPER ALLOY 485
CU0103COPPER ALLOY 510
CU0106COPPER ALLOY 524
CU0109COPPER ALLOY 544
CU0111COPPER ALLOY 606
CU0112COPPER ALLOY 610
CU0115COPPER ALLOY 614
CU0122COPPER ALLOY 630
CU0206COPPER ALLOY 932
CCA000COTTON
GSA000GLASS
GSB000GLASS FIBER
FEA000IRON
FEF000IRON ALLOY
FE0019IRON ALLOY 660
MGB000MAGNESIUM ALLOY
MG0008MAGNESIUM ALLOY AZ91C
MG0006MAGNESIUM ALLOY ZK60A
NLA000NICKEL
NLB000NICKEL ALLOY
NL0008NICKEL ALLOY 400
NL0035NICKEL ALLOY 41
PPA000PAPER
LBJ000PETROLATUM
PCA000PLASTIC
PCB000PLASTIC ACETAL
PCG000PLASTIC DIALLYL PHTHALATE
PCH000PLASTIC EPOXY
PCN000PLASTIC PHENOLIC
PCP000PLASTIC POLYAMIDE (NYLON)
PCQ000PLASTIC POLYCAPROLACTAM
PCR000PLASTIC POLYCARBONATE
PCZ000PLASTIC POLYHEXAMETHYLENE ADIPAMIDE
PCAM00PLASTIC POLYHEXAMETHYLENE AMIDE
PCAA00PLASTIC POLYHEXAMETHYLENE SEBACAMIDE
PCAF00PLASTIC POLYTETRAFLUOROETHYLENE
STA000STEEL
ST1008STEEL COMP 1008
ST1010STEEL COMP 1010
ST1011STEEL COMP 1011
ST1012STEEL COMP 1012
ST1015STEEL COMP 1015
ST1016STEEL COMP 1016
ST1017STEEL COMP 1017
ST1018STEEL COMP 1018
ST1019STEEL COMP 1019
ST1020STEEL COMP 1020
ST1021STEEL COMP 1021
ST1022STEEL COMP 1022
ST1023STEEL COMP 1023
ST1025STEEL COMP 1025
ST1026STEEL COMP 1026
ST1029STEEL COMP 1029
ST1030STEEL COMP 1030
ST1031STEEL COMP 1031
ST1033STEEL COMP 1033
ST1034STEEL COMP 1034
ST1035STEEL COMP 1035
ST1037STEEL COMP 1037
ST1038STEEL COMP 1038
ST1039STEEL COMP 1039
ST1040STEEL COMP 1040
ST1042STEEL COMP 1042
ST1043STEEL COMP 1043
ST1045STEEL COMP 1045
ST1046STEEL COMP 1046
ST1049STEEL COMP 1049
ST1050STEEL COMP 1050
ST1053STEEL COMP 1053
ST1055STEEL COMP 1055
ST1060STEEL COMP 1060
ST1064STEEL COMP 1064
ST1065STEEL COMP 1065
ST1069STEEL COMP 1069
ST1070STEEL COMP 1070
ST1074STEEL COMP 1074
ST1075STEEL COMP 1075
ST1078STEEL COMP 1078
ST1080STEEL COMP 1080
ST1084STEEL COMP 1084
ST1085STEEL COMP 1085
ST1086STEEL COMP 1086
ST1090STEEL COMP 1090
ST1095STEEL COMP 1095
ST1108STEEL COMP 1108
ST1109STEEL COMP 1109
ST1110STEEL COMP 1110
ST1115STEEL COMP 1115
ST1116STEEL COMP 1116
ST1117STEEL COMP 1117
ST1118STEEL COMP 1118
ST1119STEEL COMP 1119
ST1120STEEL COMP 1120
ST1125STEEL COMP 1125
ST1126STEEL COMP 1126
ST1132STEEL COMP 1132
ST1137STEEL COMP 1137
ST1138STEEL COMP 1138
ST1139STEEL COMP 1139
ST1140STEEL COMP 1140
ST1141STEEL COMP 1141
ST1144STEEL COMP 1144
ST1145STEEL COMP 1145
ST1146STEEL COMP 1146
ST1151STEEL COMP 1151
ST1211STEEL COMP 1211
ST1212STEEL COMP 1212
ST1213STEEL COMP 1213
ST1215STEEL COMP 1215
ST0063STEEL COMP 12L14
ST1524STEEL COMP 1524
ST1527STEEL COMP 1527
ST1536STEEL COMP 1536
ST1541STEEL COMP 1541
ST1548STEEL COMP 1548
ST1551STEEL COMP 1551
ST1552STEEL COMP 1552
ST1561STEEL COMP 1561
ST1566STEEL COMP 1566
ST1572STEEL COMP 1572
ST0202STEEL COMP 202
ST0159STEEL COMP 203EZ
ST0301STEEL COMP 301
ST0302STEEL COMP 302
ST0180STEEL COMP 302B
ST0303STEEL COMP 303
ST0166STEEL COMP 303 PLUS X
ST0157STEEL COMP 303CU
ST0165STEEL COMP 303MA
ST0158STEEL COMP 303PB
ST0078STEEL COMP 303S
ST0079STEEL COMP 303SE
ST0304STEEL COMP 304
ST0080STEEL COMP 304L
ST0305STEEL COMP 305
ST0152STEEL COMP 308
ST0309STEEL COMP 309
ST0153STEEL COMP 309S
ST0310STEEL COMP 310
ST0154STEEL COMP 310S
ST0155STEEL COMP 314
ST0316STEEL COMP 316
ST0082STEEL COMP 316L
ST0317STEEL COMP 317
ST0254STEEL COMP 317L
ST0321STEEL COMP 321
ST0322STEEL COMP 322
ST0323STEEL COMP 323
ST0324STEEL COMP 324
ST0347STEEL COMP 347
ST0348STEEL COMP 348
ST0384STEEL COMP 384
ST0385STEEL COMP 385
ST0403STEEL COMP 403
ST0405STEEL COMP 405
ST0410STEEL COMP 410
ST4130STEEL COMP 4130
ST0414STEEL COMP 414
ST4140STEEL COMP 4140
ST0093STEEL COMP 4140H
ST0416STEEL COMP 416
ST0255STEEL COMP 416 PLUS X
ST0099STEEL COMP 416SE
ST0420STEEL COMP 420
ST0100STEEL COMP 420F
ST0284STEEL COMP 420FSE
ST0430STEEL COMP 430
ST0101STEEL COMP 430F
ST0172STEEL COMP 430FSE
ST0431STEEL COMP 431
ST4340STEEL COMP 4340
ST0105STEEL COMP 440A
ST0106STEEL COMP 440B
ST0107STEEL COMP 440C
ST0108STEEL COMP 440F
ST0285STEEL COMP 440FSE
ST0446STEEL COMP 446
ST0630STEEL COMP 630
ST0633STEEL COMP 633
ST0634STEEL COMP 634
ST8630STEEL COMP 8630
ST8640STEEL COMP 8640
ST8740STEEL COMP 8740
ST0026STEEL COMP E3310
ST0028STEEL COMP E4340
ST0171STEEL COMP M1010
ST0220STEEL COMP M1012
ST0176STEEL COMP M1015
ST0221STEEL COMP M1017
ST0163STEEL COMP M1020
ST0291STEEL COMP O1
ST0288STEEL COMP O6
ST0299STEEL COMP W112
ST0704STEEL COMP XM-12
ST0187STEEL COMP XM-13
STB000STEEL CORROSION RESISTING
ST0573STEEL UNS K02102
ST0552STEEL UNS K02600
ST0574STEEL UNS K02708
ST0532STEEL UNS K24065
ST0692STEEL UNS K93602
TTB000TITANIUM
TTA000TITANIUM ALLOY
TT0052TITANIUM ALLOY UNS R56400
ZNA000ZINC ALLOY
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETGSTANDOFF
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AP33)Reply
QAEROSPACE MATERIAL SPEC STD
JAMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP18)Reply
M10TH MATERIAL RESPONSE
N11TH MATERIAL RESPONSE
P12TH MATERIAL RESPONSE
Q13TH MATERIAL RESPONSE
R14TH MATERIAL RESPONSE
S15TH MATERIAL RESPONSE
T16TH MATERIAL RESPONSE
U17TH MATERIAL RESPONSE
W18TH MATERIAL RESPONSE
X19TH MATERIAL RESPONSE
B1ST MATERIAL RESPONSE
Y20TH MATERIAL RESPONSE
Z21ST MATERIAL RESPONSE
V22ND MATERIAL RESPONSE
C2ND MATERIAL RESPONSE
D3RD MATERIAL RESPONSE
E4TH MATERIAL RESPONSE
F5TH MATERIAL RESPONSE
H6TH MATERIAL RESPONSE
J7TH MATERIAL RESPONSE
K8TH MATERIAL RESPONSE
L9TH MATERIAL RESPONSE
GALL MATERIAL RESPONSES
ASINGLE MATERIAL RESPONSE
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDPHD000*;SFTT3AEEDPHD000$DCDA000*;SFTT3AEEDPHD000$$DCDA000*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (SF01)Reply
ANA000ANODIZE
CDA000CADMIUM
CLB000CERAMIC
CMA000CHROMATE
CMB000CHROMATE ZINC
CRA000CHROMIUM
CUA000COPPER
DCA000DICHROMATE
ENA000ENAMEL
AUA000GOLD
LQA000LACQUER
NLA000NICKEL
XXB000OXIDE
XXA000OXIDE FILM
PNA000PAINT
PDA000PALLADIUM
PSA000PASSIVATE
PHA000PHOSPHATE
PHC000PHOSPHATE MANGANESE
PHD000PHOSPHATE ZINC
PCY000PLASTIC POLYURETHANE
AGA000SILVER
SNA000TIN
SNB000TIN ALLOY
ZNA000ZINC
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AP33)Reply
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP39)Reply
M10TH TREATMENT RESPONSE
N11TH TREATMENT RESPONSE
P12TH TREATMENT RESPONSE
Q13TH TREATMENT RESPONSE
R14TH TREATMENT RESPONSE
S15TH TREATMENT RESPONSE
B1ST TREATMENT RESPONSE
C2ND TREATMENT RESPONSE
D3RD TREATMENT RESPONSE
E4TH TREATMENT RESPONSE
F5TH TREATMENT RESPONSE
H6TH TREATMENT RESPONSE
J7TH TREATMENT RESPONSE
K8TH TREATMENT RESPONSE
L9TH TREATMENT RESPONSE
GALL TREATMENT RESPONSES
ASINGLE TREATMENT RESPONSE
IF STYLE/REPLY CODE(s) AEL WERE ENTERED FOR MRC ANLR, YOU MUST ANSWER MRC (ADWD and ADWH)
IF STYLE/REPLY CODE(s) AND WERE ENTERED FOR MRC ANLR, YOU MUST ANSWER MRC (ADWD and ADWH)
IF STYLE/REPLY CODE(s) AHH, ASL OR BDT WERE ENTERED FOR MRC ANLR, YOU MUST ANSWER MRC (ASDB)
IF STYLE/REPLY CODE(s) APL WERE ENTERED FOR MRC ANLR, YOU MUST ANSWER MRC (ABMZ)
ANLRDCROSS-SECTIONAL SHAPE
THE GEOMETRIC CONFIGURATION OF THE ITEM WHEN VIEWED IN CROSS SECTION.
Enter the applicable reply code from the table below
(ANLRDASL)
Table 1
Reply Code (AD07)Reply
AELELLIPTICAL
AHHHEXAGON
BDTOCTAGON
ANDRECTANGULAR
APLROUND
ASLSQUARE
ADWD*JCROSS-SECTIONAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS SECTION,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWDJAA2.0*;ADWDJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADWH*JCROSS-SECTIONAL WIDTH
A MEASUREMENT OF THE CROSS SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWHJAA2.0*;ADWHJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAB2.0*;ASDBJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAB2.0*;ABMZJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
IF STYLE/REPLY CODE(s) 1, 6, 11 OR 12 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and CXXW and CXXX)
IF STYLE/REPLY CODE(s) 2, 3, 8 OR 58 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY)
IF STYLE/REPLY CODE(s) 4, 10, 13 OR 21 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CXXS and CXXT and ABRY and CXXX and CXXW)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and CLYK and CDTC and AAVZ and ABGF and CLYH) or (ABRY) or (CLYK) or (CDTC) or (AAVZ) or (ABGF and CLYJ) or (ABRY and CLYK and CDTC and AAVZ and AGWA and CLYH) or (ABRY and CLYK and CDTC and AAVZ and AGWA and CLYJ)
IF STYLE/REPLY CODE(s) 7, 14, 15 OR 17 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and ABKU and ABKK) or (ABRY and ABKU and AFGG)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPZ and ABRY and CXXX and CXXW)
IF STYLE/REPLY CODE(s) 16 OR 18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CXXT and CXXS and ABRY)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and CXXX and CXXW)
IF STYLE/REPLY CODE(s) 20 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CXXW and CXXX and ABRY and ABKU and AFGG) or (CXXW and CXXX and ABRY and ABKU and ABKK)
IF STYLE/REPLY CODE(s) 22 OR 23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAUB and ABRY and CXXX and CXXW)
IF STYLE/REPLY CODE(s) 24 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CXXS and CXXT and ABRY and CXXX and AAUB and CXXW)
IF STYLE/REPLY CODE(s) 25 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and AAVK and AAZX and AAVH and AAZW) or (ABRY and AAVK and AAZX and AAVH and CXXY) or (ABRY and AAVK and AAZX and AAVJ and AAZW) or (ABRY and AAVK and AAZX and AAVJ and CXXY)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and ABKU and ABKK) or (ABRY and ABKU and AFGG)
IF STYLE/REPLY CODE(s) 40, 41, 52 OR 59 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and CXXT and CXXX)
IF STYLE/REPLY CODE(s) 42 OR 51 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABNZ and CXXT)
IF STYLE/REPLY CODE(s) 43, 50 OR 53 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABNZ)
IF STYLE/REPLY CODE(s) 44 OR 45 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABNZ and CXXX)
IF STYLE/REPLY CODE(s) 57 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and CXXX)
IF STYLE/REPLY CODE(s) 65 OR 66 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (BRHQ)
IF STYLE/REPLY CODE(s) 67 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AAVK and AAVH and ABKU and CXXX and ABKK) or (AAVK and AAVH and ABKU and CXXX and AFGG)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL19)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AAL10321PROJECTION ONE END W/ RIGHT EXTERNAL THREAD
AAL105210PROJECTION BOTH ENDS LEFT AND RIGHT INTERNAL THREADS
AAL105311PROJECTION ONE END LEFT AND RIGHT INTERNAL THREADS
AAL105412PROJECTION ONE END
AAL105513PROJECTION BOTH ENDS
AAL105614FLANGED RIGHT EXTERNAL THREADS
AAL105715FLANGED
AAL105816PROJECTION ONE END LEFT INTERNAL THREAD
AAL105917FLANGED LEFT INTERNAL THREAD
AAL106018PROJECTION ONE END LEFT INTERNAL THREAD
AAL106119PROJECTION ONE END LEFT INTERNAL THREAD
AAL10332LEFT INTERNAL THREAD
AAL106220PROJECTION AND FLANGE LEFT INTERNAL AND RIGHT EXTERNAL THREAD
AAL106321PROJECTION BOTH ENDS RIGHT EXTERNAL THREAD
AAL106422PROJECTION ONE END LEFT INTERNAL THREAD
AAL106523PROJECTION ONE END LEFT AND RIGHT INTERNAL THREADS
AAL106624PROJECTION BOTH ENDS LEFT INTERNAL THREADS
AAL106725TWO SHOULDERS LEFT INTERNAL AND RIGHT EXTERNAL THREADS
AAL106826FLANGED LEFT AND RIGHT INTERNAL THREADS
AAL10343INTERNALLY THREADED FULL LENGTH
AAL10354LEFT INTERNAL AND RIGHT EXTERNAL THREAD
AAL106940THREADED, SNAP-IN
AAL107041THREADED, SNAP-IN
AAL107142THREADED, SNAP-IN
AAL107243THREADED, SNAP-IN
AAL107344THREADED, SNAP-IN
AAL107445THREADED, SNAP-IN
AAL10365GROOVED W/ LEFT INTERNAL AND RIGHT EXTERNAL THREAD
AAL107550SNAP-IN
AAL107651SNAP-IN
AAL107752SNAP-IN
AAL107853SNAP-IN
AAL107957HINGED, THREADED
AAL108058HINGED, THREADED
AAL108159HINGED, THREADED
AAL10376LEFT INTERNAL AND RIGHT EXTERNAL THREAD
AAL108265HINGED, SNAP-IN
AAL108366HINGED, SNAP-IN
DQ0026467LEFT INTERNAL AND RIGHT EXTERNAL THREADS
AAL10387FLANGED WITH LEFT INTERNAL THREAD
AAL10398LEFT INTERNAL AND RIGHT INTERNAL THREADS
AAL10409PROJECTION ONE END RIGHT EXTERNAL THREADS
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJAB2.0*;AASYJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATBJAC2.0*;AATBJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAA2.0*;AAUBJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAVH*JSHOULDER DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVHJAC2.0*;AAVHJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAVJ*JSHOULDER WIDTH ACROSS FLATS
THE SHORTEST DISTANCE FROM ONE FLATTED SURFACE OF THE SHOULDER TO THE OPPOSITE FLATTED SURFACE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVJJAA2.0*;AAVJJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAVK*JSHOULDER LENGTH
THE LENGTH OF THE ENLARGED PORTION/S/ LOCATED ON THE SHANK OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVKJAC2.0*;AAVKJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAVZ*JGROOVE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GROOVE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVZJAC2.0*;AAVZJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAZW*JSECOND SHOULDER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZWJAC2.0*;AAZWJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AAZX*JSECOND SHOULDER LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZXJAB2.0*;AAZXJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAC2.0*;ABGFJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAA2.0*;ABKKJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABKU*JFLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKUJAA2.0*;ABKUJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABNZ*JEFFECTIVE LENGTH
A MEASUREMENT OF THE LONGEST EFFECTIVE DIMENSION OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNZJAB2.0*;ABNZJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABPZ*JEND RADIUS
A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPZJAB2.0*;ABPZJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABXQ*JFLATTED PORTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXQJAC2.0*;ABXQJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADNU*JCORNER RADIUS
A MEASUREMENT OF A STRAIGHT LINE FROM THE MIDPOINT OF A ROUNDED CORNER TO ITS PERIPHERY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNUJAA2.0*;ADNUJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AFGG*JFLANGE WIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS, PERPENDICULIAR TO THE HEIGHT OF THE FLANGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFGGJAB2.0*;AFGGJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AGWA*JGROOVE RADIUS
A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF A GROOVE TO THE INSIDE SURFACE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGWAJAB2.0*;AGWAJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
BFKT*JDISTANCE FROM END TO HOLE CENTER
THE DISTANCE FROM THE END OF THE ITEM TO THE CENTER OF THE HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFKTJAC2.0*;BFKTJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
BPCJ*JDISTANCE BETWEEN HOLE CENTERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BPCJJAA2.0*;BPCJJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
BRHQ*JEFFECTIVE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRHQJAB2.0*;BRHQJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CDTC*JDISTANCE FROM END TO GROOVE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CDTCJAB2.0*;CDTCJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYB*JRIGHT END CHAMFER DEPTH
NONE. REPLACED BY MRC AGHG WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYBJAC2.0*;CLYBJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYC*JLEFT END CHAMFER DEPTH
NONE. REPLACED BY MRC AGHG WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYCJAB2.0*;CLYCJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYD*JRIGHT PROJECTION CHAMFER DEPTH
NONE. REPLACED BY MRC AGHG WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYDJAA2.0*;CLYDJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYF*JLEFT PROJECTION CHAMFER DEPTH
NONE. REPLACED BY MRC AGHG WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYFJAC2.0*;CLYFJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYH*JSMALLER GROOVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYHJAC2.0*;CLYHJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYJ*JSMALLER GROOVE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYJJAC2.0*;CLYJJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYK*JSMALLER GROOVE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYKJAB2.0*;CLYKJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CLYM*JDISTANCE FROM END TO SMALLER GROOVE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYMJAA2.0*;CLYMJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CMNN*JDISTANCE FROM END TO FLATTED SECTION
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CMNNJAA2.0*;CMNNJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CMPD*JDISTANCE FROM CENTERLINE TO SECOND FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CMPDJAB2.0*;CMPDJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXH*JLEFT SLOT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXHJAC2.0*;CXXHJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXK*JLEFT SLOT DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXKJAC2.0*;CXXKJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXL*JRIGHT SLOT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXLJAA2.0*;CXXLJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXM*JRIGHT SLOT DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXMJAA2.0*;CXXMJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXN*JLEFT COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXNJAA2.0*;CXXNJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXP*JLEFT COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXPJAA2.0*;CXXPJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXQ*JRIGHT COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXQJAC2.0*;CXXQJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXR*JRIGHT COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXRJAB2.0*;CXXRJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXS*JLEFT PROJECTION DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXSJAB2.0*;CXXSJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXT*JLEFT PROJECTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXTJAA2.0*;CXXTJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXW*JRIGHT PROJECTION DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXWJAC2.0*;CXXWJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXX*JRIGHT PROJECTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXXJAB2.0*;CXXXJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXY*JSECOND SHOULDER WIDTH ACROSS FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXYJAB2.0*;CXXYJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXXZ*JLEFT COUNTERSINK ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXXZJDA2.0*;CXXZJDA2.0$$JDA2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXYB*JRIGHT COUNTERSINK ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXYBJRA2.0*;CXYBJRA2.0$$JRA2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXYC*JLEFT END CHAMFER ANGLE
NONE. REPLACED BY MRC CSYT WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXYCJRB2.0*;CXYCJRB2.0$$JRB2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXYD*JRIGHT END CHAMFER ANGLE
NONE. REPLACED BY MRC CSYT WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXYDJDB2.0*;CXYDJDB2.0$$JDB2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXYF*JPROJECTION.LEFT CHAMFER ANGLE
NONE. REPLACED BY MRC CSYT WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXYFJDB2.0*;CXYFJDB2.0$$JDB2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CXYH*JRIGHT PROJECTION CHAMFER ANGLE
NONE. REPLACED BY MRC CSYT WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXYHJRA2.0*;CXYHJRA2.0$$JRA2.1*)
Table 1
Reply Code (AP38)Reply
DDEGREES
RRADIANS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CMPF*AHOLE QUANTITY PERPENDICULAR TO AXIS
NONE.
Enter the numeric reply with a minimum of one digit.
(CMPFA10*)
CMPH*AFLANGE HOLE QUANTITY
NONE.
Enter the numeric reply with a minimum of one digit.
(CMPHA10*)
IF STYLE/REPLY CODE(s) AM, JC, JE, JF, JS, NC, NE, NF, NJ, NS, UN OR WW WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJE)
IF STYLE/REPLY CODE(s) BA, EM, MJ, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CQQR) or (CQJX and CQQR and AAJE)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and CQQR)
THSDDTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3ETJDJC*;THSD3ETJDJC$DNS*;THSD3ETJDJC$$DNS*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETJLEFT EXTERNAL
3ETKRIGHT EXTERNAL
3ETLHOLE PERPENDICULAR TO AXIS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AH06)Reply
AMACME
BABA
SMISO M
SSISO S
EMM
MJMJ
UNUN
NEUNEF
NFUNF
NCUNIFIED NATIONAL COARSE (UNC)
NJUNIFIED NATIONAL JOINT (UNJ)
JFUNIFIED NATIONAL JOINT FINE (UNJF)
JCUNJC
JEUNJEF
JSUNJS
NMUNM
NSUNS
WWWHITWORTH
CQJXJNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3ETJJA2.0*;CQJX3ETJJA2.0$JA2.0*;CQJX3ETJJA2.0$$JA2.1*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETJLEFT EXTERNAL
3ETKRIGHT EXTERNAL
3ETLHOLE PERPENDICULAR TO AXIS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CMLP3ETHAK7)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETKRIGHT EXTERNAL
3HOULOCATION NOT OTHERWISE SPECIFIED
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CQQR3AEEB2.0)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETIRIGHT INTERNAL
3HOULOCATION NOT OTHERWISE SPECIFIED
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(AAJD3ETHAL1)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETKRIGHT EXTERNAL
3HOULOCATION NOT OTHERWISE SPECIFIED
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJE3AEEJAM32.0/P50.0*;AAJE3AEEJAM32.0/P50.0$$JA*;AAJE3AEEJAM32.0/P50.0$JAM32.0/P50.0*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETIRIGHT INTERNAL
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAJFDTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AAJF3ETKDAAG*;AAJF3ETKDAAG$DAAL*;AAJF3ETKDAAG$$DAAL*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETJLEFT EXTERNAL
3ETKRIGHT EXTERNAL
3ETLHOLE PERPENDICULAR TO AXIS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AA38)Reply
AAGLEFT-HAND
AALRIGHT-HAND
AASAJTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASA3AEEJAC2.0*;AASA3AEEJAC2.0$JAC2.0*;AASA3AEEJAC2.0$$JAC2.1*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3ETHLEFT INTERNAL (INCLUDES THRU THREAD)
3ETIRIGHT INTERNAL
3ETJLEFT EXTERNAL
3ETKRIGHT EXTERNAL
3ETLHOLE PERPENDICULAR TO AXIS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 3
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAEQ)
Table 1
Reply Code (AN47)Reply
AEQCASEHARDENED
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
Table 1
Reply Code (AC28)Reply
ASPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
BSTANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
CDRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
Table 1
Reply Code (AN62)Reply
VFEDERAL MOTOR VEHICLE SAFETY STANDARD
FFLAMMABILITY STANDARD
SGOVERNMENT SPECIFICATION
TGOVERNMENT STANDARD
UINTERNATIONAL STD/SPEC
DMANUFACTURERS SOURCE CONTROL
RMANUFACTURERS SPECIFICATION
NMANUFACTURERS SPECIFICATION CONTROL
MMANUFACTURERS STANDARD
BNATIONAL STD/SPEC
APROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
PPROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
Table 1
Reply Code (AD08)Reply
ALALLOY
BEANNEALED
ANANNEX
APAPPENDIX
ACAPPLICABILITY CLASS
ARARRANGEMENT
ASASSEMBLY
ABASSORTMENT
BFBOND
BXBOX
CYCAPACITY
CACASE
CTCATEGORY
CFCIRCUMFERENCE
CLCLASS
CECODE
CRCOLOR
CCCOMBINATION CODE
CNCOMPONENT
CPCOMPOSITION
CMCOMPOUND
CDCONDITION
AVCONFIGURATION
CSCONSTRUCTION
BGCORE CONDITION
CBCUT OFF
AMDELAY CLASS
DEDESIGN
DGDESIGNATOR
DWDRAWING NUMBER
DUDUPLEX
EGEDGE
ENEND
FYFAMILY
FGFIGURE
AKFILE NUMBER
FNFINISH
FBFLAVOR
BHFLUX PERCENTAGE
FMFORM
FAFORMULA
AJGAGE STOCK NUMBER
GRGRADE
GAGRADUATION
AXGRANULES
AYGRIT
GBGROUND
GPGROUP
HAHEAVY DUTY
BAIMAGE COLOR
NSINSERT
TMITEM
KDKIND
KTKIT
LGLENGTH
LVLEVEL
LTLIMIT
MKMARK
AAMARKER
ADMASK APERTURE
MLMATERIAL
BBMAXIMUM DENSITY
TAMEDIUM TEMPER
MHMESH
MEMETHOD
BCMINIMUM DENSITY
MDMODEL
MTMOUNTING
AQNATURAL
AUNON-DELAY CLASS
NRNUMBER
BLOUTFIT NUMBER
PAPARAGRAPH
PTPART
PNPATTERN
PCPHYSICAL CONDITION
PSPIECE
PLPLAN
PRPOINT
PDPOLISHED
PBPRESSURE RATING
QAQUALITY
QBQUENCHED
RNRANGE
AERAPID
RTRATING
RFREFERENCE NUMBER
RAREGULAR DUTY
BJRMA FLUX
SJSALIENT CHARACTERISTICS
SCSCHEDULE
SBSECTION
SLSELECTION
BDSERIALIZED
SESERIES
SVSERVICE
SXSET
SASHADE
SHSHAPE
SGSHEET
SZSIZE
AGSLOW
TCSOFT TEMPER
SKSOURCE
PZSPECIES
SQSPECIFICATION SHEET
SDSPEED
AWSTANDARD
SRSTRAIGHT
STSTYLE
SSSUBCLASS
SFSUBFORM
SPSUBTYPE
BKSUPPORT
SNSURFACE CONDITION
SYSYMBOL
SMSYSTEM
TBTABLE
TNTANNAGE
TPTEMPER
TXTEXTURE
TKTHICKNESS
TTTREATMENT
TRTRIM
TYTYPE
YNUNIT
AZUNSERIALIZED
VAVARIETY
WTWEIGHT
WDWIDTH
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
Table 1
Reply Code (AN58)Reply
AADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDAGA000$DRTA000*;PRMTDAGA000$$DRTA000*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAGA000E2.0*;PMWTJAGA000E2.0$$JAGA000E2.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
Table 2
Reply Code (AG14)Reply
EGRAINS, TROY
RGRAMS
FOUNCES, TROY
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA0002.0*;PMLCJPDA0002.0$JPDA0002.0*;PMLCJPDA0002.0$$JPDA0002.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)