NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED39011*)
ADLEJVACUUM RATING
THE ULTIMATE MAXIMUM VACUUM,EXPRESSED IN TERMS OF ABSOLUTE PRESSURE,THAT MAY BE PRODUCED BY OR APPLIED TO AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADLEJT2.0*)
| Table 1 |
| Reply Code (AC43) | Reply |
| M | INCHES OF MERCURY |
| U | MICROTORR |
| L | MILLITORR |
| P | PASCAL |
| T | TORR |
AERPDSYSTEM DESIGN
AN INDICATION OF THE SYSTEM FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AERPDB*;AERPDC$DB*)
| Table 1 |
| Reply Code (AD26) | Reply |
| B | CORROSIVE |
| C | NONCORROSIVE |
AENGDPUMPING ELEMENT TYPE
INDICATES THE TYPE OF PUMPING ELEMENT INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AENGDC*;AENGDG$$DF*)
| Table 1 |
| Reply Code (AD04) | Reply |
| A | ANY ACCEPTABLE |
| H | LIQUID PISTON |
| C | LOBE |
| F | ROTARY PISTON |
| G | SLIDING VANE |
AAYDASTAGE QUANTITY
THE NUMBER OF STAGES INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYDA10*)
AEQG*DVAPOR CONDENSATION PREVENTATIVE DEVICE
THE DEVICE WHICH PREVENTS OR REDUCES THE AMOUNT OF CONDENSABLE VAPORS FROM ENTERING AND CONTAMINATING THE ITEM.
Enter the applicable reply code from the table below
(AEQGDD*;AEQGDB$$DC*)
| Table 1 |
| Reply Code (AD24) | Reply |
| D | GAS BALLAST VALVING |
| C | LIQUID NITROGEN COLD TRAP |
| B | WATER CAP |
ACZV*DCOOLING MEDIUM
THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable reply code from the table below
(ACZVDA*;ACZVDAAD$$DACN*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AAB | AIR |
| A | ANY ACCEPTABLE |
| AAD | OIL |
| ACN | WATER |
AAYTAINTAKE CONNECTION QUANTITY
THE NUMBER OF INTAKE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYTA10*)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AAYU, YOU MUST ANSWER MRC (ASWT and CXBW and CXCD) or (ASWT and CXBW and CXCM)
IF STYLE/REPLY CODE(s) AN WERE ENTERED FOR MRC AAYU, YOU MUST ANSWER MRC (AENM)
IF STYLE/REPLY CODE(s) AB OR AP WERE ENTERED FOR MRC AAYU, YOU MUST ANSWER MRC (AENN)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC AAYU, YOU MUST ANSWER MRC (AENQ)
AAYU*DINTAKE CONNECTION TYPE
INDICATES THE TYPE OF INTAKE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYUDAB*;AAYUDAN$$DAL*)
| Table 1 |
| Reply Code (AA84) | Reply |
| A | ANY ACCEPTABLE |
| AQ | FLANGED |
| AB | FLARED TUBE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
ASWT*JINTAKE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INTAKE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(ASWTJJC2.0*;ASWTJJC2.0$$JJC2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BSF |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NS | UNS |
AENM*JINTAKE CONNECTION OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AENMJAA2.0*;AENMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXBW*DINTAKE CONNECTION THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CXBWDSP)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BSF |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NS | UNS |
CXCD*JINTAKE CONNECTION NOMINAL THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INTAKE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXCDJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXCM*BINTAKE CONNECTION THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CXCMB2.0)
AENN*JINTAKE CONNECTION INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AENNJAA2.0*;AENNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AENQ, YOU MUST ANSWER MRC (AENV and AENW and AEPB and AEPC and AEPD)
AENQ*LINTAKE CONNECTION FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE INTAKE CONNECTION FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AENQL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAS1437 | 1 | ROUND |
AENV*JINTAKE CONNECTION FLANGE OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AENVJAC2.0*;AENVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AENW*JINTAKE CONNECTION FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AENWJAB2.0*;AENWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPC*JINTAKE CONNECTION BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPCJAB2.0*;AEPCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPD*JINTAKE CONNECTION BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPDJAC2.0*;AEPDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPB*AINTAKE CONNECTION BOLT HOLE QUANTITY
NONE.
Enter the numeric reply with a minimum of one digit.
(AEPBA10*)
AAYVADISCHARGE CONNECTION QUANTITY
THE NUMBER OF DISCHARGE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYVA10*)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AAYW, YOU MUST ANSWER MRC (ASAZ and CXDH and CXDR) or (ASAZ and CXDH and CXFJ)
IF STYLE/REPLY CODE(s) AN WERE ENTERED FOR MRC AAYW, YOU MUST ANSWER MRC (AEPH)
IF STYLE/REPLY CODE(s) AB OR AP WERE ENTERED FOR MRC AAYW, YOU MUST ANSWER MRC (AEPJ)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC AAYW, YOU MUST ANSWER MRC (AEPQ)
AAYW*DDISCHARGE CONNECTION TYPE
INDICATES THE TYPE OF DISCHARGE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYWDAB*;AAYWDAM$$DAL*)
| Table 1 |
| Reply Code (AA84) | Reply |
| A | ANY ACCEPTABLE |
| AQ | FLANGED |
| AB | FLARED TUBE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
ASAZ*JDISCHARGE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE DISCHARGE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(ASAZJJF2.0*;ASAZJJF2.0$$JJF2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BSF |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NS | UNS |
AEPH*JDISCHARGE CONNECTION OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPHJAA2.0*;AEPHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXDH*DDISCHARGE CONNECTION THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CXDHDNF)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BSF |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NS | UNS |
CXDR*JDISCHARGE CONNECTION NOMINAL THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE DISCHARGE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXDRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXFJ*BDISCHARGE CONNECTION THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CXFJB2.0)
AEPJ*JDISCHARGE CONNECTION INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE DISCHARGE CONNECTION,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPJJAA2.0*;AEPJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AEPQ, YOU MUST ANSWER MRC (CQNG and AEPS and AEPX and AEPY and AEPZ)
AEPQ*LDISCHARGE CONNECTION FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE DISCHARGE CONNECTION FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AEPQL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAS1437 | 1 | ROUND |
CQNG*JDISCHARGE CONNECTION FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQNGJAA2.0*;CQNGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPS*JDISCHARGE CONNECTION FLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE DISCHARGE CONNECTION FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPSJAA2.0*;AEPSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPY*JDISCHARGE CONNECTION BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPYJAC2.0*;AEPYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPZ*JDISCHARGE CONNECTION BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEPZJAB2.0*;AEPZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEPX*ADISCHARGE CONNECTION BOLT HOLE QUANTITY
NONE.
Enter the numeric reply with a minimum of one digit.
(AEPXA10*)
AAXWBBRAKE HORSEPOWER REQUIRED
THE POWER REQUIRED TO START AND OPERATE THE ITEM AT THE ACTUAL RATED CAPACITY,INCLUDING ALL ACCESSORIES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAXWB2.0)
AEQCBOPERATING SPEED AT RATED CAPACITY IN RPM
THE SPEED OF THE DRIVE SHAFT REQUIRED TO PRODUCE THE RATED CAPACITY OF AN ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEQCB2.0*;AEQCB2.0$$BM2.0*)
AEQHJAIR DISPLACEMENT RATE
THE VOLUME OF AIR PASSED PER UNIT OF TIME THROUGH AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEQHJAB2.0*)
| Table 1 |
| Reply Code (AC64) | Reply |
| A | CUBIC FEET PER MINUTE |
| C | CUBIC METERS PER MINUTE |
| Table 2 |
| Reply Code (AD25) | Reply |
| B | IN FREE AIR |
AAXX*DMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDAAL)
| Table 1 |
| Reply Code (AA78) | Reply |
| A | ANY ACCEPTABLE |
| AAB | BASE |
| AAF | HAND CARRY |
| AAH | HORIZONTAL TANK |
| AAK | SKID |
| AAL | TRACTOR |
| AAM | TRAILER |
| AAP | WHEEL |
AAYX*DDRIVE CONNECTION TYPE
INDICATES THE TYPE OF CONNECTION BETWEEN THE PRIME MOVER AND THE SHAFT.
Enter the applicable reply code from the table below
(AAYXDAF)
| Table 1 |
| Reply Code (AA85) | Reply |
| A | ANY ACCEPTABLE |
| AB | BEVEL GEAR |
| AL | CAM |
| AM | CLOSE COUPLED |
| AF | FLAT BELT |
| AN | FLEXIBLE COUPLED |
| AJ | MULTISTRAND CHAIN |
| AG | MULTISTRAND V-BELT |
| AP | RIGID COUPLED |
| AH | SINGLE STRAND V-BELT |
| BX | SPLINE |
| AD | SPUR GEAR |
AEQE*JVACUUM STORAGE TANK CAPACITY
THE VOLUME OF THE VACUUM STORAGE CONTAINER/S/.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEQEJJ2.0*)
| Table 1 |
| Reply Code (AB10) | Reply |
| J | CUBIC FEET |
| R | CUBIC METERS |
BPRZ*DSAFETY DEVICE TYPE
INDICATES THE TYPE OF SAFETY DEVICE(S) PROVIDED.
Enter the applicable reply code from the table below
(BPRZDACF*;BPRZDACH$$DADC*)
| Table 1 |
| Reply Code (AM97) | Reply |
| ADC | COMBINATION CURRENT AND THERMAL OVERLOAD DEVICE |
| ACF | HIGH TEMPERATURE SHUTDOWN SWITCH |
| ACH | LOW PRESSURE OIL SHUTDOWN SWITCH |
| ADB | OVERLOAD RELAY |
| ADA | SAFETY RELIEF VALVE |
BDML*DCONTROL DEVICE TYPE
INDICATES THE TYPE OF CONTROL DEVICE PROVIDED.
Enter the applicable reply code from the table below
(BDMLDADD*;BDMLDACX$$DACR*)
| Table 1 |
| Reply Code (AM97) | Reply |
| ADD | AUTOMATIC SPEED REGULATOR |
| ACQ | AUTOMATIC START-STOP |
| ACR | CONSTANT SPEED |
| ACT | MANUAL SPEED REGULATOR |
| ACX | MOTOR STARTER |
| ACY | SUCTION MODULATION |
AEQJ*JMINIMUM OPERATING TEMP
THE MINIMUM TEMPERATURE AT WHICH THE ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEQJJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAYG*;CBBLDAGH$$DAYL*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AYH | EXTERNAL THERMAL PROTECTOR |
| AGJ | FUNGUS RESISTANT TREATMENT |
| AGH | HEATING EQUIPMENT |
| AYM | LOCKOUT FOR CHECKING REFRIGERANT LEAKS |
| AYL | OIL TRAP AT OUTLET |
| AYJ | REVERSIBLE ROTATION |
| AYG | SEPARATOR TANK |
| AYK | SHAFT EXTENSION |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAN0)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAE8)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information