An electric or battery-powered item designed and used to regulate the flow of tube feeding
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED38826*)
AHYVJMAXIMUM DISCHARGE FLOW RATE
THE MAXIMUM RATED CAPACITY DELIVERED BY THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYVJE2.0*;AHYVJE2.0$$JE2.1*)
| Table 1 |
| Reply Code (AC64) | Reply |
| M | GALLONS PER MINUTE |
| E | LITERS PER MINUTE |
AHYW*JDISCHARGE PRESSURE
THE PRESSURE OF THE MEDIA DELIVERED BY THE ITEM AT MAXIMUM RATED DISCHARGE CAPACITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYWJC2.0*;AHYWJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AB18) | Reply |
| C | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
AHYZ*JOPERATING SPEED AT RATED CAPACITY
THE SPEED OF THE ITEM REQUIRED TO PRODUCE ITS RATED CAPACITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYZJE2.0*;AHYZJE2.0$$JE2.1*)
| Table 1 |
| Reply Code (AA22) | Reply |
| D | REVOLUTIONS PER MINUTE |
| E | STROKES PER MINUTE |
AHZA*DPUMPING ELEMENT OPERATING POSITION
THE POSITION IN WHICH THE PUMPING ELEMENT/S/ IS DESIGNED TO OPERATE.
Enter the applicable reply code from the table below
(AHZADD)
| Table 1 |
| Reply Code (AC60) | Reply |
| D | VERTICAL |
| B | HORIZONTAL |
IF STYLE/REPLY CODE(s) AF, AJ, AK, AL OR AM WERE ENTERED FOR MRC AHZP, YOU MUST ANSWER MRC (AHZQ)
AHZP*DVOLUME CONTROL TYPE
INDICATES THE TYPE OF DEVICE USED TO CONTROL THE OUTPUT OR CAPACITY OF AN ITEM.
Enter the applicable reply code from the table below
(AHZPDAM)
| Table 1 |
| Reply Code (AH83) | Reply |
| AF | HYDRAULIC CYLINDER |
| AM | PRESSURE COMPENSATION |
| AG | PUSH-PULL |
| AH | ROTARY |
| AJ | SERVO MOTOR |
| AK | SERVO PISTON |
| AL | SYNCHRO |
AHZQ*DCONTROL LOCATION
INDICATES THE LOCATION OF THE CONTROL ON THE ITEM.
Enter the applicable reply code from the table below
(AHZQDGK)
| Table 1 |
| Reply Code (AE46) | Reply |
| EW | CENTER |
| GK | LEFT SIDE |
| GL | RIGHT SIDE |
AHZR*DROTARY PUMP DESIGN
THE DESIGN OF A ROTARY PUMP AS DETERMINED BY THE MECHANICAL PRINCIPLE USED TO ACHIEVE MOVEMENT OF THE FLUID.
Enter the applicable reply code from the table below
(AHZRDM*;AHZRDG$$DN*)
| Table 1 |
| Reply Code (AA81) | Reply |
| E | CAM AND PISTON |
| F | FLEXIBLE MEMBER |
| G | GEAR |
| H | KNUCKLE |
| J | LOBE |
| K | LOBULAR |
| L | SCREW |
| M | SHUTTLE BLOCK |
| N | VANE |
AHZT*DOPERATION METHOD
THE MEANS BY WHICH THE ITEM IS OPERATED. PLEASE USE MRC APHE IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AHZTDG)
| Table 1 |
| Reply Code (AA77) | Reply |
| C | MANUAL |
| G | POWERED |
IF YOU ANSWER MRC AAYT, YOU MUST ANSWER MRC (AAYU)
AAYT*AINTAKE CONNECTION QUANTITY
THE NUMBER OF INTAKE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYTA10*)
AAYU*DINTAKE CONNECTION TYPE
INDICATES THE TYPE OF INTAKE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYUDAF*;AAYUDAG$$DAM*)
| Table 1 |
| Reply Code (AA84) | Reply |
| BG | BELL MOUTH |
| BH | BUTT WELD |
| BK | COMPRESSION TUBE |
| AB | FLARED TUBE |
| BJ | OCTAGON FLANGE |
| AD | OVAL FLANGE |
| BC | QUICK DISCONNECT |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AH | TRIANGULAR FLANGE |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
AAYV*ADISCHARGE CONNECTION QUANTITY
THE NUMBER OF DISCHARGE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYVA10*)
AAYW*DDISCHARGE CONNECTION TYPE
INDICATES THE TYPE OF DISCHARGE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYWDAE*;AAYWDBJ$$DAM*)
| Table 1 |
| Reply Code (AA84) | Reply |
| BG | BELL MOUTH |
| BH | BUTT WELD |
| BK | COMPRESSION TUBE |
| AB | FLARED TUBE |
| BJ | OCTAGON FLANGE |
| AD | OVAL FLANGE |
| BC | QUICK DISCONNECT |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AH | TRIANGULAR FLANGE |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
AAYX*DDRIVE CONNECTION TYPE
INDICATES THE TYPE OF CONNECTION BETWEEN THE PRIME MOVER AND THE SHAFT.
Enter the applicable reply code from the table below
(AAYXDAE)
| Table 1 |
| Reply Code (AA85) | Reply |
| AB | BEVEL GEAR |
| AL | CAM |
| AS | CHAIN |
| AM | CLOSE COUPLED |
| AE | COG BELT |
| AF | FLAT BELT |
| AN | FLEXIBLE COUPLED |
| AT | FRICTION CLUTCH |
| AQ | GEAR |
| AC | HELICAL GEAR |
| AJ | MULTISTRAND CHAIN |
| AG | MULTISTRAND V-BELT |
| AP | RIGID COUPLED |
| AK | SINGLE STRAND CHAIN |
| AH | SINGLE STRAND V-BELT |
| AD | SPUR GEAR |
| AR | V-BELT |
AJAB*DDRIVE SHAFT TYPE
INDICATES THE TYPE OF DRIVE SHAFT BY THE PHYSICAL CONFIGURATION,CONDITION,AND THE LIKE OF THE SHAFT END.
Enter the applicable reply code from the table below
(AJABDCM*;AJABDAE$$DAC*)
| Table 1 |
| Reply Code (AF58) | Reply |
| CN | D-TYPE |
| CM | KEY TYPE, EXTERNAL |
| AL | KEY TYPE, INTERNAL |
| AG | MACHINE KEYWAY |
| AM | PLAIN ROUND |
| AD | SPLINED, INVOLUTE EXTERNAL |
| AE | SPLINED, INVOLUTE INTERNAL |
| AB | SPLINED, STRAIGHT EXTERNAL |
| AC | SPLINED, STRAIGHT INTERNAL |
| AN | SQUARE |
| AK | TAPERED |
| AF | THREADED |
| AJ | TONGUE |
| AH | WOODRUFF KEYWAY |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information