An instrument for measuring the rate of flow of a fluid through a pipeline. This measurement is indicated on a graduated scale either by means of a float confined in a tube, or pointer connected to a vane, or piston and spring or the like. Excludes:METER, FLUID FLOW INDICATING, DIFFERENTIAL PRESSURE; METER, FLUID FLOW INDICATING, ELECTROMAGNETIC; and METER, FLUID FLOW INDICATING, ULTRASONIC.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED38346*)
IF STYLE/REPLY CODE(s) BRF WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (ARQS and BHJT and AXQG)
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDBSV*;APGFDBRF$DBSE*)
| Table 1 |
| Reply Code (AK54) | Reply |
| BRF | CASE |
| BSV | ELECTRONIC |
| AZN | GLASS |
| BSE | PURGE METER |
APSJASCALE QUANTITY
THE NUMBER OF SCALES ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(APSJA10*)
BHBYFDIAL SCALE MARKING RANGE
THE MINIMUM AND MAXIMUM MARKINGS ON A DIAL SCALE.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(BHBYFM2.0/P4.7*)
CPZKDDIAL SCALE REFERENCE POINTER
AN INDICATION OF WHETHER OR NOT A DIAL SCALE REFERENCE POINTER IS INCLUDED.
Enter the applicable reply code from the table below
(CPZKDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) AY WERE ENTERED FOR MRC ANTH, YOU MUST ANSWER MRC (AWAE and CPZM and BHSQ and MATT)
ANTHDMETER TYPE
AN INDICATION OF THE TYPE OF METER.
Enter the applicable reply code from the table below
(ANTHDAY)
| Table 1 |
| Reply Code (AK13) | Reply |
| AY | FLOAT |
| AZ | PISTON/SPRING |
| BA | POINTER CONNECTED TO VANE |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CPZNDINTEGRAL PULSATION DAMPENER
AN INDICATION OF WHETHER OR NOT AN INTEGRAL PULSATION DAMPENER IS INCLUDED.
Enter the applicable reply code from the table below
(CPZNDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ACQWDINLET CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF INLET CONNECTION.
Enter the applicable reply code from the table below
(ACQWDFU*;ACQWDRB$DA*)
| Table 1 |
| Reply Code (AB76) | Reply |
| A | ANY ACCEPTABLE |
| BF | FLANGE |
| PF | HOSE NIPPLE |
| QM | PUSH-ON UNIT |
| FU | QUICK DISCONNECT MALE |
| RB | STANDARD GROUND GLASS SOCKET |
| BG | THREADED |
IF STYLE/REPLY CODE(s) AAP WERE ENTERED FOR MRC CPZP, YOU MUST ANSWER MRC (CPZQ)
CPZPDINLET CONNECTION POSITION FOR WHICH DESIGNED
THE INLET CONNECTION POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(CPZPDAAP*;CPZPDAAF$DAAP*)
| Table 1 |
| Reply Code (AM84) | Reply |
| AAP | HORIZONTAL |
| AAF | VERTICAL |
ARTHDOUTLET CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF OUTLET CONNECTION.
Enter the applicable reply code from the table below
(ARTHDBG*;ARTHDPF$DADC*)
| Table 1 |
| Reply Code (AB76) | Reply |
| A | ANY ACCEPTABLE |
| ADC | FEMALE QUICK DISCONNECT |
| BF | FLANGE |
| PF | HOSE NIPPLE |
| BG | THREADED |
IF STYLE/REPLY CODE(s) AAP WERE ENTERED FOR MRC CPZR, YOU MUST ANSWER MRC (CPZS)
CPZRDOUTLET CONNECTION POSITION FOR WHICH DESIGNED
THE OUTLET CONNECTION POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(CPZRDAAP*;CPZRDAAF$DAAF*)
| Table 1 |
| Reply Code (AM84) | Reply |
| AAP | HORIZONTAL |
| AAF | VERTICAL |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AHZU, YOU MUST ANSWER MRC (AYTM)
AHZUDINTEGRAL RELIEF VALVE
AN INDICATION OF WHETHER OR NOT AN INTEGRAL SAFETY DEVICE IS INCLUDED.
Enter the applicable reply code from the table below
(AHZUDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
BNHNDINTEGRAL HEAT SOURCE
AN INDICATION OF WHETHER OR NOT AN INTEGRAL HEAT SOURCE IS INCLUDED.
Enter the applicable reply code from the table below
(BNHNDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
CPZTDALARM SIGNAL
AN INDICATION OF WHETHER OR NOT AN ALARM SIGNAL IS INCLUDED.
Enter the applicable reply code from the table below
(CPZTDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ARQS*DCONSTRUCTION
THE STRUCTURAL CHARACTERISTIC OF THE ITEM. PLEASE USE MRC CQCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ARQSDAHP*;ARQSDAHK$DAHN*)
| Table 1 |
| Reply Code (AL59) | Reply |
| A | ANY ACCEPTABLE |
| AHH | ARMORED |
| AHN | INCLOSED W/SIGHT WINDOW |
| AHJ | OPEN FRONT |
| AHK | OPEN POST |
| AHL | OPEN POST W/PROTECTION BOX |
| AHM | OPEN POST W/PROTECTION SHIELD |
| AHP | SIDE PLATE |
BHJT*DBASE
AN INDICATION OF WHETHER OR NOT A BASE(S) IS INCLUDED.
Enter the applicable reply code from the table below
(BHJTDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AXQG*DCARRYING HANDLE
AN INDICATION OF WHETHER OR NOT A CARRYING HANDLE IS INCLUDED.
Enter the applicable reply code from the table below
(AXQGDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF YOU ANSWER MRC CPZF, YOU MUST ANSWER MRC (MATT)
CPZF*AMETERING TUBE QUANTITY
THE NUMBER OF METERING TUBES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(CPZFA10*)
AMKD*DINDICATOR TYPE
INDICATES THE TYPE OF DEVICE USED TO REGISTER THE CONDITION(S).
Enter the applicable reply code from the table below
(AMKDDALY*;AMKDDANA$DAHF*)
| Table 1 |
| Reply Code (AJ12) | Reply |
| A | ANY ACCEPTABLE |
| ALS | BALL FLOAT |
| ANA | DIGITAL |
| AHF | DIGITAL DISPLAY |
| ALT | FLOAT EXTENSION STEM CONNECTED TO DIAL POINTER |
| ALW | FLOAT MAGNETICALLY COUPLED TO INDICATOR IN EXTENSION CHAMBER |
| ALX | FLOAT MAGNETICALLY COUPLED TO SCALE POINTER |
| ALZ | SIGHT WINDOW SET DIRECTLY IN TUBE |
| ALY | SIGHT WINDOWS IN EXTENSION CHAMBER |
IF STYLE/REPLY CODE(s) DR WERE ENTERED FOR MRC ATEQ, YOU MUST ANSWER MRC (ACKL and ASTW)
IF STYLE/REPLY CODE(s) DS WERE ENTERED FOR MRC ATEQ, YOU MUST ANSWER MRC (CPZG and CPZH)
ATEQ*DSCALE TYPE
INDICATES THE TYPE OF SCALE.
Enter the applicable reply code from the table below
(ATEQDDS*;ATEQDDR$DDR*)
| Table 1 |
| Reply Code (AM12) | Reply |
| DR | DIRECT CAPACITY READING |
| DS | MILLIMETER REFERENCE READING |
ACKL*DMEDIA FOR WHICH DESIGNED
THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACKLDA*;ACKLDDE$DAU*)
| Table 1 |
| Reply Code (AB75) | Reply |
| SD | 0IL |
| AB | AIR |
| MY | AIRCRAFT FUEL |
| A | ANY ACCEPTABLE |
| AJ | ARGON |
| TM | CALIBRATION |
| AU | CHEMICALS |
| AW | DIESEL FUEL |
| TN | DISODIUM PHOSPHATE |
| TP | ETHYLENE |
| BB | ETHYLENE GLYCOL |
| BD | GAS |
| BE | GASOLINE |
| BL | HELIUM |
| BM | HYDRAULIC OIL |
| BV | JET FUELS |
| DT | LIQUID |
| SJ | LIQUID HYDROGEN |
| NC | LIQUID NITROGEN |
| SG | LIQUID OXYGEN |
| CC | LUBRICATING OIL |
| MA | NITROGEN GAS |
| TQ | NONFREEZING LIQUID |
| CM | OXYGEN |
| CN | OXYGEN, GASEOUS |
| HT | PETROLEUM |
| SW | PETROLEUM BASE |
| KX | PETROLEUM PRODUCTS |
| GZ | PETROLEUM, LIQUID |
| TR | PHOTOGRAPHIC SOLUTION |
| KY | ROCKET FUEL, RP-1 |
| JB | RPI FUEL |
| TS | SILICONE HEAT TRANSFER FLUID |
| TT | SKYDROL 500A |
| TW | SKYDROL 7000 HYDRAULIC |
| DC | STEAM |
| TX | STODDARD SOLVENT |
| ET | SULPHUR HEXAFLUORIDE |
| DE | TRICHLORETHYLENE |
| DF | WATER |
| KZ | WATER, COLD |
| DH | WATER, FRESH |
| LA | WATER, HOT |
| DL | WATER, SALT |
| TY | WATER-GLYCOL |
ASTW*GSCALE MARKING
AN INDICATION OF THE MARKING(S) ON THE SCALE.
Enter clear text.
(ASTWGCLEARTEXT)
CPZG*BMAXIMUM WATER CAPACITY IN GALLONS PER MINUTE
THE MAXIMUM AMOUNT OF WATER FOR WHICH THE ITEM IS RATED,EXPRESSED IN GALLONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CPZGB2.0)
CPZH*BMAXIMUM AIR CAPACITY IN CUBIC FEET PER MINUTE
THE MAXIMUM AMOUNT OF AIR FOR WHICH THE ITEM IS RATED,EXPRESSED IN CUBIC FEET PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CPZHB2.0)
AEWH*FDIAL RANGE
THE MINIMUM AND MAXIMUM LIMITS OF VARIATION IN CAPACITY THAT A DIAL WILL MEASURE.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AEWHFM2.0/P4.7*)
CPZJ*GDIAL SCALE SMALLEST INCREMENT
THE SMALLEST INCREMENT OF GRADUATION ON THE DIAL SCALE.
Enter clear text.
(CPZJGCLEARTEXT)
AWAE*AFLOAT QUANTITY
THE NUMBER OF FLOATS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AWAEA10*)
CPZL*AFLOAT QUANTITY PER TUBE
THE NUMBER OF FLOATS IN EACH TUBE.
Enter the numeric reply with a minimum of one digit.
(CPZLA10*)
CPZM*DSPINNING FLOAT
AN INDICATION OF WHETHER OR NOT A SPINNING FLOAT IS INCLUDED.
Enter the applicable reply code from the table below
(CPZMDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) AAGZ WERE ENTERED FOR MRC BHSQ, YOU MUST ANSWER MRC (BMHW)
BHSQ*DFLOAT TYPE
INDICATES THE TYPE OF FLOAT USED.
Enter the applicable reply code from the table below
(BHSQDAAGZ*;BHSQDAAGY$DAAGZ*)
| Table 1 |
| Reply Code (AE98) | Reply |
| AAGY | FREE |
| AAGZ | GUIDED |
BMHW*DGUIDE TYPE
INDICATES THE TYPE OF GUIDE PROVIDED.
Enter the applicable reply code from the table below
(BMHWDBR*;BMHWDBU$DBT*)
| Table 1 |
| Reply Code (AD58) | Reply |
| BR | BEADED TUBE |
| CH | FLUTED TUBE |
| BV | HIGH CAPACITY FLUTED GUIDE |
| BS | HOLLOW TAPERED ROD |
| BU | MOLDED GLASS INTEGRAL W/TUBE |
| BT | SOLID ROD |
IF STYLE/REPLY CODE(s) AFS WERE ENTERED FOR MRC APQB, YOU MUST ANSWER MRC (AXGY)
APQB*DUNIT TYPE
INDICATES THE TYPE OF UNIT.
Enter the applicable reply code from the table below
(APQBDAMB*;APQBDAFS$DAFS*)
| Table 1 |
| Reply Code (AK95) | Reply |
| AFS | MOUNTED |
| AMB | PORTABLE |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDARY*;AXGYDA$DAWC*)
| Table 1 |
| Reply Code (AM39) | Reply |
| A | ANY ACCEPTABLE |
| BMM | DIRECT LINE |
| ARY | FLUSH PANEL |
| AWC | SURFACE PANEL |
CPZD*GINLET CONNECTION SIZE
DESIGNATES THE SIZE OF THE INLET CONNECTION INCLUDED ON THE ITEM.
Enter clear text.
(CPZDGCLEARTEXT)
CPZQ*DINLET CONNECTION DEVICE TYPE
INDICATES THE TYPE OF INLET CONNECTION DEVICE PROVIDED.
Enter the applicable reply code from the table below
(CPZQDBPY*;CPZQDAEP$DBPY*)
| Table 1 |
| Reply Code (AK95) | Reply |
| AEP | STATIONARY |
| BPY | SWIVEL |
ACRN*JINLET BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INLET BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACRNJAB2.0*;ACRNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACRL*AINLET BOLT HOLE QUANTITY
THE NUMBER OF INLET BOLT HOLES ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACRLA10*)
ACRM*JINLET BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INLET BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACRMJAA2.0*;ACRMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BHCM*GOUTLET CONNECTION SIZE
DESIGNATES THE SIZE OF THE OUTLET CONNECTION INCLUDED ON THE ITEM.
Enter clear text.
(BHCMGCLEARTEXT)
CPZS*DOUTLET CONNECTION DEVICE TYPE
INDICATES THE TYPE OF OUTLET CONNECTION DEVICE PROVIDED.
Enter the applicable reply code from the table below
(CPZSDBPY*;CPZSDAEP$DAEP*)
| Table 1 |
| Reply Code (AK95) | Reply |
| AEP | STATIONARY |
| BPY | SWIVEL |
BHCS*JOUTLET BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BHCSJAC2.0*;BHCSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BHCT*AOUTLET BOLT HOLE QUANTITY
THE NUMBER OF OUTLET BOLT HOLE(S) ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(BHCTA10*)
BHCW*JOUTLET BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BHCWJAA2.0*;BHCWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BPHD*JMAXIMUM WORKING PRESSURE
THE MAXIMUM WORKING PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BPHDJEY2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| FB | POUNDS PER SQUARE INCH |
| JS | POUNDS PER SQUARE INCH GAGE |
AYTM*DUNIT LOCATION
INDICATES THE LOCATION OF THE UNIT.
Enter the applicable reply code from the table below
(AYTMDDTL*;AYTMDDTH$DDQP*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| A | ANY ACCEPTABLE |
| DTG | LOWER CENTER FRONT |
| CKS | LOWER LEFT FRONT |
| DTH | LOWER REAR |
| CKT | LOWER RIGHT FRONT |
| DHW | RIGHT CENTER FRONT |
| DQP | UPPER CENTER |
| DTL | UPPER RIGHT SIDE |
AQQB*DILLUMINATIVE METHOD
THE MEANS OF PRODUCING ILLUMINATION.
Enter the applicable reply code from the table below
(AQQBDA*;AQQBDBB$DBN*)
| Table 1 |
| Reply Code (AL21) | Reply |
| A | ANY ACCEPTABLE |
| BB | FLUORESCENT LAMP |
| BN | INCANDESCENT LAMP |
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRTA000*;PRMTDAZA000$DPDA000*;PRMTDAZA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000E2.0*;PMWTJRHA000E2.0$$JRHA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAJ8)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAV2)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
PKQT*AINTERMEDIATE PACKAGE QUANTITY
THE NUMBER OF WRAPS,BOXES,OR BUNDLES,WHICH CONTAINS TWO OR MORE UNITS OF ISSUE,PLACED INSIDE AN EXTERIOR CONTAINER.
Enter the numeric reply with a minimum of one digit.
(PKQTA10*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ052*;HZRDDHAZ285$$DHAZ012*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ012 | COPPER |
| HAZ285 | PLASTIC |
| HAZ052 | ZINC |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDFEB000*;MATT3AEEDFEB000$DCUB000*;MATT3AEEDFEB000$$DCUB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADW | TUBE |
| 3AEE | OVERALL |
| 3CZM | FLOAT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUB000 | COPPER ALLOY |
| GSA000 | GLASS |
| GSE000 | GLASS BOROSILICATE |
| GSJ000 | GLASS OPTICAL |
| FEB000 | IRON CAST |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCK000 | PLASTIC METHYL METHACRYLATE |
| PCP000 | PLASTIC POLYAMIDE |
| RCE000 | RUBBER |
| JWE000 | SAPPHIRE |
| STA000 | STEEL |
| ST0316 | STEEL COMP 316 |
| STB000 | STEEL CORROSION RESISTING |
| MTF000 | TANTALUM |
| TNA000 | TUNGSTEN |
| TNB000 | TUNGSTEN CARBIDE |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADW | TUBE |
| 3AEE | OVERALL |
| 3CZM | FLOAT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information