A resistor in which a sliding or rolling contact moves over an exposed area of the resistive element to change the ohmic value of the output. The finctional tolerance (linearity) of the output is equal to or less than plus or minus 1 percent on linear outputs. Specified outputs such as sine, cosine, tangent, and the like, shall be considered to be precision. Fr items having manually position taps designed to be set and fixed prior to use, see RESISTOR,ADJUSTABLE. For items with step by step variation, see REHOSTAT and RESISTOR, STEP BY STEP. For tandem-mounted items designed to function together as an attenuator (and rated accordingly), see ATTENUATOR, VARIABLE. Excludes:RESISTOR (1), VARIABLE, WIRE WOUND, NONPRECISION; RESISTOR (1), VARIABLE NONWIRE WOUND, NONPRECISION; and RESISTOR (1), VARIABLE, WIRE WOUND, PRECISION.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED37407*)
AAPNASECTION QUANTITY
THE NUMBER OF INDIVIDUAL ELEMENTS.
Enter the numeric reply with a minimum of one digit.
(AAPNA10*)
CQCCJELECTRICAL RESISTANCE PER SECTION
A MEASURE OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT PER SECTION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQCCJGZCQ2.0*;CQCCJGZCQ2.0$$JGZCQ2.1*)
| Table 1 |
| Reply Code (AN86) | Reply |
| GZ | GIGOHMS |
| KZ | KILOHMS |
| MZ | MEGOHMS |
| ZZ | OHMS |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
CRSSJRESISTANCE TOLERANCE PER SECTION IN PERCENT
THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE PER SECTION OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRSSJCTM32.0/P50.0*;CRSSJCTM32.0/P50.0$$JCT*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes IF YOU ANSWER MRC CRGM, YOU MUST ANSWER MRC (CSBX and CQFL)
CRGM*HFUNCTION CONFORMITY PER SECTION
THE FIDELITY OF THE RELATIONSHIP BETWEEN THE ACTUAL FUNCTION CHARACTERISTICS AND THE THEORETICAL FUNCTION PER SECTION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CRGMHERF2.0*;CRGMHERF2.0$$HERF2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
| Table 2 |
| Reply Code (AC86) | Reply |
| F | ABSOLUTE CONFORMITY |
| E | ABSOLUTE LINEARITY |
| B | INDEPENDENT LINEARITY |
| G | PROPORTIONAL CONFORMITY |
| H | STEPPED CONFORMITY |
| D | TERMINAL BASE LINEARITY |
| C | ZERO BASED LINEARITY |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CSBX*HFUNCTION CHARACTERISTIC PER SECTION
THE SPECIFIED MATHEMATICAL RELATION PER SECTION BETWEEN THE TERMINAL RESISTANCE,OR OUTPUT RATIO,AND THE ROTATION OF THE ACTUATOR.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CSBXHCXAK2.0*;CSBXHCXAK2.0$$HCXAK2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
| Table 2 |
| Reply Code (AC85) | Reply |
| AF | 180 DEG SINE |
| AK | 20 DB LOG. |
| AD | 360 DEG COSINE |
| AC | 360 DEG SINE |
| AB | 360 DEG SINE-COSINE |
| AL | 40 DB LOG. |
| AM | 50 DB LOG. |
| AH | 90 DEG SINE |
| AE | DOUBLE SIDED SQUARE |
| AQ | EQUATION |
| AP | GRAPH |
| AA | LINEAR |
| AG | SINGLE SIDED SQUARE |
| AN | TABLE |
| AJ | TANGENTIAL PORM 75 DEG |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQFL*JFUNCTION CONFORMITY TOLERANCE PER SECTION
THE PERMISSIBLE RANGE PER SECTION BY WHICH THE ACTUAL VALUE OF RESISTANCE OR VOLTAGE AT ANY SPECIFIED POINT MAY DEVIATE FROM THE THEORETICAL VALUE FOR THE LINEAR OR NONLINEAR FUNCTION,EXPRESSED AS A MINUS AND PLUS PERCENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CQFLJCNM32.0/P50.0*;CQFLJCNM32.0/P50.0$$JCN*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEFZ*JSHAFT RUNOUT
THE ECCENTRICITY OF THE SHAFT DIAMETER WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT,MEASURED AT A SPECIFIED DISTANCE FROM THE END OF THE SHAFT,WHEN THE BODY OF THE ITEM IS HELD FIXED AND THE SHAFT IS ROTATED WITH A SPECIFIED LOAD APPLIED RADIALLY TO THE SHAFT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFZJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEGA*JLATERAL RUNOUT
THE PERPENDICULARITY OF THE MOUNTING SURFACE,WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT,AND MEASURED ON THE MOUNTING SURFACE AT A SPECIFIED DISTANCE FROM THE OUTSIDE EDGE OF THE MOUNTING SURFACE,WHEN THE SHAFT IS HELD FIXED AND THE BODY OF THE ITEM IS ROTATED WITH SPECIFIED LOADS APPLIED RADIALLY AND AXIALLY TO THE BODY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEGAJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEGB*JPILOT DIAMETER RUNOUT
THE ECCENTRICITY OF THE PILOT DIAMETER WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT AND MEASURED ON THE PILOT DIAMETER WHEN THE SHAFT IS HELD AND THE BODY OF THE ITEM IS ROTATED WHILE A SPECIFIED LOAD IS APPLIED RADIALLY TO THE BODY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEGBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEGC*JSHAFT RADIAL PLAY
THE TOTAL RADIAL EXCURSION OF THE SHAFT MEASURED AT A SPECIFIED DISTANCE FROM THE FRONT SURFACE OF THE UNIT WITH A SPECIFIED RADIAL LOAD APPLIED ALTERNATELY IN OPPOSITE DIRECTIONS AT A SPECIFIED POINT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEGCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEGD*BMECHANICAL BACKLASH IN DEG ANGULAR ROTATION
THE MAXIMUM DIFFERENCE OF SHAFT POSITION THAT OCCURS WHEN THE SHAFT IS MOVED TO THE SAME ACTUAL OUTPUT RATIO POINT FROM OPPOSITE DIRECTIONS,EXPRESSED IN DEGREE ANGULAR ROTATION.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEGDB2.0)
AEFY*JSHAFT END PLAY
THE TOTAL AXIAL EXCURSION OF THE SHAFT MEASURED AT THE END OF THE SHAFT WITH A SPECIFIED AXIAL LOAD APPLIED ALTERNATELY IN THE OPPOSITE DIRECTIONS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEFM*JMAXIMUM STOP TORQUE
THE MAXIMUM AMOUNT OF TURNING FORCE THAT CAN BE APPLIED THROUGH THE OPERATING SHAFT WITH0UT DAMAGE TO THE STOPS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFMJA2.0*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| A | INCH-OUNCES |
AEFK*JMAXIMUM STARTING TORQUE
THE MAXIMUM AMOUNT OF TURNING FORCE REQUIRED TO INITIATE THE ACTUATOR MOVEMENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFKJA2.0*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| A | INCH-OUNCES |
AEFL*JMAXIMUM RUNNING TORQUE
THE MAXIMUM AMOUNT OF FORCE REQURED TO MAINTAIN ACTUATOR MOVEMENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFLJA2.0*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| A | INCH-OUNCES |
CRFJ*JTEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS
A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE CAUSED BY A CHANGE IN TEMPERATURE PER SECTION,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRFJJCQM32.0/P50.0*;CRFJJCQM32.0/P50.0$$JCQ*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CSCY*JTEMP COEFFICIENT OF RESISTANCE WIRE PER SECTION IN PPM PER DEG CELSIUS
A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE OF THE WIRE PER SECTION OF WHICH THE RESISTANCE ELEMENT OF A RESISTOR IS WOUND,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CSCYJCYM32.0/P50.0*;CSCYJCYM32.0/P50.0$$JCY*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
CQDB*JRESISTANCE TEMP CHARACTERISTIC RANGE PER SECTION IN PERCENT
THE CHANGE IN TOTAL RESISTANCE OVER A SPECIFIED TEMPERATURE RANGE PER SECTION,EXPRESSED AS A PERCENT OF THE TOTAL RESISTANCE AT A SPECIFIED REFERENCE TEMPERATURE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CQDBJAACQM32.0/P50.0*;CQDBJAACQM32.0/P50.0$$JAACQ*)
| Table 1 |
| Reply Code (AC90) | Reply |
| AH | 0 DEG CELSIUS |
| AQ | 105 DEG CELSIUS |
| AR | 120 DEG CELSIUS |
| AS | 125 DEG CELSIUS |
| AG | -15 DEG CELSIUS |
| AT | 150 DEG CELSIUS |
| AU | 175 DEG CELSIUS |
| AJ | 25 DEG CELSIUS |
| AF | -25 DEG CELSIUS |
| AK | 40 DEG CELSIUS |
| AE | -40 DEG CELSIUS |
| AL | 45 DEG CELSIUS |
| AD | -45 DEG CELSIUS |
| AM | 50 DEG CELSIUS |
| AC | -50 DEG CELSIUS |
| AB | -55 DEG CELSIUS |
| AA | -65 DEG CELSIUS |
| AN | 75 DEG CELSIUS |
| AP | 85 DEG CELSIUS |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CRGDJPOWER DISSIPATION RATING PER SECTION IN WATTS
THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED PER SECTION,EXPRESSED IN WATTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRGDJCEQ2.0*;CRGDJCEQ2.0$$JCEQ2.1*)
| Table 1 |
| Reply Code (AC89) | Reply |
| B | FREE AIR |
| C | HEAT SINK |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CSDH*JAMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER
THE AMBIENT TEMPERATURE,EXPRESSED IN DEGREES CELSIUS,OF THE MEDIUM SURROUNDING EACH SECTION AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSDHJEQ2.0*;CSDHJEQ2.0$$JEQ2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQGN*JAMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER
THE AMBIENT TEMPERATURE AT WHICH THE POWER DISSIPATION OF EACH SECTION IS DERATED TO ZERO PERCENT OF THE FULL RATED POWER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQGNJCP2.0*;CQGNJCP2.0$$JCP2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CRJS*JFIXED TAP QUANTITY PER SECTION
THE NUMBER OF FIXED TERMINALS AT POINTS BETWEEN THE END TERMINALS THAT PROVIDE CONNECTION TO THE INTERMEDIATE VALUES OF THE TOTAL VALUE PER SECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CRJSJCW2*;CRJSJCW2$$JCW3*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CSBW*JTAP LOCATION FROM CCW TERMINAL PER SECTION IN OHMS
INDICATES THE LOCATION OF A TAP RELATIVE TO THE COUNTERCLOCKWISE TERMINAL PER SECTION,EXPRESSED IN OHMS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBWJCT2.0*;CSBWJCT2.0$$JCT2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQCH*JTAP LOCATION FROM CCW TERMINAL PER SECTION IN DEG OF EFFECTIVE ELECTRICAL ROTATION
THE LOCATION PER SECTION,IN DEGREES,OF EFFECTIVE ELECTRICAL ROTATION BETWEEN THE COUNTERCLOCKWISE TERMINAL OF A RESISTOR AND EACH TAP TERMINAL.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQCHJCY2.0*;CQCHJCY2.0$$JCY2.1*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CRKS*JTAP LOCATION TOLERANCE PER SECTION
THE LIMITS OF PERMISSIBLE VARIATION FROM THE RATED VALUE OF THE LOCATION OF A TAP PER SECTION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRKSJBCWM32.0/P50.0*;CRKSJBCWM32.0/P50.0$$JBCW*)
| Table 1 |
| Reply Code (AD00) | Reply |
| B | DEG ANGULAR ROTATION |
| A | OHMS |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| EM | 11TH SECTION |
| EN | 12TH SECTION |
| EP | 13TH SECTION |
| EQ | 14TH SECTION |
| ER | 15TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) 1B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ABPM and ADAP)
IF STYLE/REPLY CODE(s) 11B, 36B OR 40B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAP and ADAQ)
IF STYLE/REPLY CODE(s) 4B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAVL and AAVM and ABPA and ABPC and ABPM and ABUF and ABVJ and ADAQ and AECZ and AEDA and AEDE)
IF STYLE/REPLY CODE(s) 5B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAVL and AAVM and ABPA and ABPC and ABPM and ADAQ and AECZ and AEDA)
IF STYLE/REPLY CODE(s) 10B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAVL and ABPM and ADAP and ADAQ)
IF STYLE/REPLY CODE(s) 12B, 13B, 37B, 39B, 44B, 58B OR 64B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ)
IF STYLE/REPLY CODE(s) 21B OR 22B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ and AEDE)
IF STYLE/REPLY CODE(s) 23B, 42B, 46B, 52B, 53B OR 57B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAP and ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 24B, 33B, 54B OR 55B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and AFQM and AGTP)
IF STYLE/REPLY CODE(s) 25B, 27B, 28B, 29B, 34B, 38B, 45B, 48B, 49B, 50B, 51B, 56B, 59B OR 60B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 26B, 30B, 31B OR 32B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and AGTP)
IF STYLE/REPLY CODE(s) 41B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ and AGTP)
IF STYLE/REPLY CODE(s) 43B OR 47B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAP and ADAQ and ADAT and ADAU and AGTP)
IF STYLE/REPLY CODE(s) 35B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAP and ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 61B, 62B, 63B, 65B OR 70B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAU and ADAT and ADAQ)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL50B)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AU10006 | 10B | CYLINDRICAL W/READOUT |
| AU10007 | 11B | CYLINDRICAL W/READOUT |
| AU10008 | 12B | CYLINDRICAL W/READOUT |
| AU10009 | 13B | CYLINDRICAL |
| AU10004 | 1B | CYLINDRICAL BUSHING MOUNTED |
| AU10010 | 21B | CYLINDRICAL STUDS MOUNTED |
| AU10011 | 22B | CYLINDRICAL HOLE/SLOT MOUNTED |
| AU10012 | 23B | RECTANGULAR W/BUSHING |
| AU10013 | 24B | RECTANGULAR W/MOUNTING TABS/FLANGES |
| AU10014 | 25B | RECTANGULAR |
| AU10015 | 26B | RECTANGULAR W/MOUNTING HOLES/SLOTS |
| AU10016 | 27B | RECTANGULAR |
| AU10017 | 28B | RECTANGULAR W/MOUNTING HOLE/SLOT |
| AU10018 | 29B | RECTANGULAR W/MOUNTING HOLE/SLOT |
| AU10019 | 30B | RECTANGULAR W/MOUNTING HOLES/SLOTS |
| AU10020 | 31B | RECTANGULAR W/MOUNTING HOLES/SLOTS |
| AU10021 | 32B | RECTANGULAR W/MOUNTING HOLES |
| AU10022 | 33B | RECTANGULAR W/MOUNTING HOLES/SLOTS |
| AU10164 | 34B | RECTANGULAR |
| AU10023 | 35B | RECTANGULAR BUSHING MOUNTED |
| AU10160 | 36B | CYLINDRICAL BUSHING MOUNTED |
| AU10024 | 37B | CYLINDRICAL |
| AU10025 | 38B | RECTANGULAR |
| AU10026 | 39B | CYLINDRICAL |
| AU10027 | 40B | CYLINDRICAL BUSHING MOUNTED |
| AU10028 | 41B | CYLINDRICAL TAB/FLANGE MOUNTED |
| AU10029 | 42B | RECTANGULAR W/BUSHING/HOLE MOUNTING |
| AU10030 | 43B | RECTANGULAR W/BUSHING/SLOT MOUNTED |
| AU10031 | 44B | CYLINDRICAL |
| AU10032 | 45B | RECTANGULAR |
| AU10033 | 46B | RECTANGULAR W/BUSHING |
| AU10034 | 47B | RECTANGULAR W/BUSHING/HOLES/SLOTS |
| AU10035 | 48B | RECTANGULAR |
| AU10036 | 49B | RECTANGULAR |
| AU10163 | 4B | CYLINDRICAL SERVO MOUNTED |
| AU10037 | 50B | RECTANGULAR |
| AU10038 | 51B | RECTANGULAR W/POINTER ADJUSTMENT |
| AU10039 | 52B | RECTANGULAR W/BUSHING/FLANGE MOUNTED |
| AU10040 | 53B | RECTANGULAR W/BUSHING |
| AU10041 | 54B | RECTANGULAR W/TAB/FLANGE MOUNTED |
| AU10042 | 55B | RECTANGULAR W/TAB/FLANGE MOUNTED |
| AU10043 | 56B | RECTANGULAR |
| AU10044 | 57B | RECTANGULAR BUSHING MOUNTED |
| AU10045 | 58B | CYLINDRICAL FRICTION MOUNTED |
| AU10046 | 59B | RECTILINEAR, SLIDE CONTROL |
| AU10005 | 5B | CYLINDRICAL SERVO MOUNTED |
| AU10047 | 60B | RECTANGULAR, OPEN ELEMENT |
| AU10048 | 61B | RECTANGULAR, OPEN ELEMENT |
| AU10049 | 62B | RECTANGULAR W/SLIDE CONTROL |
| AU10050 | 63B | RECTANGULAR W/HAND WHEEL |
| AU10051 | 64B | CYLINDRICAL, EDGE CONTROL OPERATED |
| AU10052 | 65B | RECTANGULAR SPLIT CONTROL |
| AU10057 | 70B | TRIMMER |
AAVL*JPILOT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THAT PORTION USED TO GUIDE THE ITEM AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVLJAC2.0*;AAVLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVM*JPILOT LENGTH
THE LENGTH OF THE PILOT,WHICH IS THE UNTHREADED PORTION BEYOND THE THREAD USED TO GUIDE THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVMJAC2.0*;AAVMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPA*JUNDERCUT DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPAJAC2.0*;ABPAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPC*JUNDERCUT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPCJAB2.0*;ABPCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAA2.0*;ABPMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAB2.0*;ADAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAB2.0*;ADAUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AECZ*JMOUNTING LIP DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AECZJAA2.0*;AECZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEDA*JMOUNTING LIP DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEDAJAB2.0*;AEDAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABUF*BANGLE OF MOUNTING HOLE IN DEG
NONE. PLEASE USE MRC CSXS IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ABUFB2.0)
ABVJ*BANGLE BETWEEN CENTERLINES OF MOUNTING HOLES IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE HALF INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ABVJB2.0)
ADAP*JMOUNTING BUSHING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAPJAA2.0*;ADAPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEDE*JMOUNTING HOLE/STUD CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEDEJAB2.0*;AEDEJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFQM*JDISTANCE BETWEEN MOUNTING HOLE CENTERS
THE DISTANCE BETWEEN THE CENTERLINE OF THE MOUNTING HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFQMJAA2.0*;AFQMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGTP*JLATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTPJAA2.0*;AGTPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B, C OR D WERE ENTERED FOR MRC AEFD, YOU MUST ANSWER MRC (AEDX)
AEFDDACTUATOR TYPE
INDICATES THE TYPE OF FACILITY OR ARRANGEMENT PROVIDED FOR MOVING THE VARIABLE CONTACT(S).
Enter the applicable reply code from the table below
(AEFDDE)
| Table 1 |
| Reply Code (AC91) | Reply |
| C | DOUBLE ENDED SHAFT |
| D | DUAL CONCENTRIC |
| E | FLUSH DRIVE WITH SLOT-HOLE |
| F | INTEGRAL KNOB |
| G | INTEGRAL KNOB WITH COUNTER |
| J | RECESSED DRIVE WITH SLOT |
| B | SINGLE SHAFT |
| K | SLIDER |
IF STYLE/REPLY CODE(s) 1C, 3C, 4C, 5C, 6C OR 7C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF)
IF STYLE/REPLY CODE(s) 2C OR 9C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABNC and ABWV and ABXF)
IF STYLE/REPLY CODE(s) 8C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AASA and ABWV and ABXF)
IF STYLE/REPLY CODE(s) 10C, 21C, 32C, 36C, 42C, 43C OR 44C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABNC and ABWV and ABXF)
IF STYLE/REPLY CODE(s) 11C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF and AEDS)
IF STYLE/REPLY CODE(s) 12C, 13C, 14C, 15C, 18C, 22C, 23C, 24C, 27C, 29C, 30C, 31C, 33C, 34C, 40C, 41C OR 46C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF)
IF STYLE/REPLY CODE(s) 16C OR 17C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF and AEDQ and AGQL)
IF STYLE/REPLY CODE(s) 19C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF and AEDQ)
IF STYLE/REPLY CODE(s) 20C OR 26C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABWV and ABXF)
IF STYLE/REPLY CODE(s) 25C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABNC and ABXF)
IF STYLE/REPLY CODE(s) 28C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF and ADAS)
IF STYLE/REPLY CODE(s) 35C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF and AEDH)
IF STYLE/REPLY CODE(s) 37C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABXF and AEDS)
IF STYLE/REPLY CODE(s) 38C OR 39C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABWV and ABXF and AEDS)
IF STYLE/REPLY CODE(s) 45C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABND and ABWV and ABXF)
IF STYLE/REPLY CODE(s) 47C WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABXF and ABNB and AEDQ and ABNC and AGQL and CXJQ and ABWV and ABNE)
AEDX*LSHAFT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AEDXL35C)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AU10067 | 10C | ROUND, PARALLEL FLATTED |
| AU10068 | 11C | ROUND, SQUARE |
| AU10069 | 12C | ROUND, MILLED, SPRING SLIT |
| AU10070 | 13C | ROUND, KNURLED |
| AU10071 | 14C | ROUND, SLOTTED, KNURLED |
| AU10072 | 15C | ROUND, MILLED |
| AU10073 | 16C | ROUND, STEPPED, KNURLED |
| AU10074 | 17C | ROUND, STEPPED |
| AU10075 | 18C | ROUND, STEPPED, UNDERCUT |
| AU10076 | 19C | ROUND, SLOTTED, STEPPED, MILLED, UNDERCUT |
| AU10058 | 1C | ROUND |
| AU10077 | 20C | ROUND, V FLATTED |
| AU10078 | 21C | ROUND, WEDGE FLATTED |
| AU10079 | 22C | ROUND, T SLOTTED |
| AU10080 | 23C | ROUND, TAPERED DOUBLE FLAT |
| AU10081 | 24C | ROUND, CROSS SLOTTED |
| AU10082 | 25C | ROUND, TAPERED FLAT |
| AU10083 | 26C | ROUND, NON-PARALLEL FLATTED |
| AU10084 | 27C | ROUND, PARALLEL FLATTED SINGLE FLATTED |
| AU10085 | 28C | ROUND, HOLLOWED |
| AU10086 | 29C | ROUND, HOLLOWED, SLOTTED |
| AU10059 | 2C | ROUND, FLATTED |
| AU10087 | 30C | ROUND, DOUBLE GROOVED |
| AU10088 | 31C | ROUND, SQUARE CHANNELLED |
| AU10089 | 32C | ROUND, FLATTED FURROWED |
| AU10090 | 33C | ROUND, DOUBLE V CHANNELLED |
| AU10091 | 34C | ROUND, V CHANNELLED |
| AU10092 | 35C | ROUND, U CHANNELLED |
| AU10093 | 36C | ROUND, FLATTED TRIPLE FURROWED |
| AU10094 | 37C | SQUARE |
| AU10095 | 38C | ROUND, SQUARED SLOTTED |
| AU10096 | 39C | ROUND, SQUARED, V CHANNELLED |
| AU10060 | 3C | ROUND, SLOTTED |
| AU10097 | 40C | ROUND, BEVEL GEARED END |
| AU10098 | 41C | ROUND, FLUTED |
| AU10099 | 42C | ROUND, FLATTED, FLUTED |
| AU10100 | 43C | ROUND, FLATTED, KNURLED, GROOVED |
| AU10101 | 44C | ROUND, SLOTTED, PARALLEL FLATTED |
| AU10102 | 45C | ROUND, TAPERED |
| AU10103 | 46C | HEXAGON SHAPE |
| AU10104 | 47C | ROUND STEPPED FLATTED |
| AU10061 | 4C | ROUND, FLAT, UNDERCUT |
| AU10062 | 5C | ROUND, UNDERCUT |
| AU10063 | 6C | ROUND, SLOTTED, UNDERCUT |
| AU10064 | 7C | ROUND, SLOTTED, FLAT UNDERCUT |
| AU10065 | 8C | ROUND, THREADED |
| AU10066 | 9C | ROUND, SLOTTED, FLATTED |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJAB2.0*;AASAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNB*JFIRST FLAT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNBJAA2.0*;ABNBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNC*JFLAT HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNCJAA2.0*;ABNCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABND*JTAPER LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNDJAC2.0*;ABNDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABWV*JSHAFT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABWVJAB2.0*;ABWVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXF*JSHAFT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXFJAB2.0*;ABXFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAS*JBODY INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADASJAC2.0*;ADASJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEDH*JCHANNEL LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEDHJAA2.0*;AEDHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEDQ*JUNDERCUT DIAMETER
NONE. PLEASE USE MRC ABPA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEDQJAC2.0*;AEDQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEDS*JSQUARE SHAFT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEDSJAC2.0*;AEDSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGQL*JUNDERCUT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGQLJAA2.0*;AGQLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNE*JSECOND FLAT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNEJAB2.0*;ABNEJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXJQ*JSECOND FLAT HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXJQJAA2.0*;CXJQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEEZ*DCONTACT ARM ELECTRICAL OFF POSITION
THE LOCATION OF THE CONTACT ARM WHEN THERE IS NO ELECTRICAL CONTINUITY BETWEEN THE MOVING CONTACT AND THE RESISTIVE ELEMENT.
Enter the applicable reply code from the table below
(AEEZDC)
| Table 1 |
| Reply Code (AC87) | Reply |
| B | FULLY CCW |
| D | FULLY CCW-CW |
| H | FULLY CENTERED |
| C | FULLY CW |
| E | FULLY EXTENDED |
| G | FULLY EXTENDED-RETRACTED |
| F | FULLY RETRACTED |
CQCK*JROTARY ACTUATOR TRAVEL IN ANGULAR DEG
THE MEASUREMENT OF THE ROTARY MECHANICAL MOTION OF THE ACTUATING SHAFT OF AN ITEM,EXPRESSED IN DEGREES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQCKJA2.0*;CQCKJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRSX*DACTUATOR TRAVEL CONTROL FEATURE
THE FEATURE THAT CONTROLS THE ACTUATOR TRAVEL.
Enter the applicable reply code from the table below
(CRSXDM*;CRSXDB$$DS*)
| Table 1 |
| Reply Code (AN94) | Reply |
| B | BRAKE |
| C | CLUTCH |
| M | CONTINUOUS MOTION |
| G | SPRING |
| S | STOPS |
AEFH*JEFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION
THAT PART OF THE TOTAL ROTATIONAL TRAVEL OF THE ACTUATOR THAT PRODUCES A CHANGE IN OUTPUT,EXPRESSED IN DEGREE ANGULAR ROTATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFHJC2.0*;AEFHJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEFN*DNONTURN DEVICE LOCATION
INDICATES THE LOCATION OF A MECHANICAL DEVICE WHICH PREVENTS THE TURNING OF THE ITEM ON ITS MOUNTED SURFACE,EXPRESSED BY THE TWELVE HOUR CLOCK DESIGNATION. PLEASE USE MRC CQPH WITH ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AEFNDAW*;AEFNDBS$DCB*;AEFNDBS$$DCB*)
| Table 1 |
| Reply Code (AC95) | Reply |
| AC | AT 1 0CLOCK |
| AH | AT 10 OCLOCK |
| BX | AT 10'30 OCLOCK |
| CC | AT 11:00 OCLOCK |
| BY | AT 12 OCLOCK |
| AM | AT 2 OCLOCK |
| BL | AT 2'30 OCLOCK |
| BS | AT 3 OCLOCK |
| BD | AT 4 OCLOCK |
| BZ | AT 4'30 OCLOCK |
| CB | AT 5:00 OCLOCK |
| BT | AT 6 OCLOCK |
| AW | AT 7 OCLOCK |
| AX | AT 7'30 OCLOCK |
| AY | AT 8 OCLOCK |
| BW | AT 9 OCLOCK |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEFP*JNONTURN DEVICE RADIUS
THE LINEAR MEASUREMENT OF THE DISTANCE FROM THE ACTUATOR CENTERLINE TO THE CENTERLINE OF THE NONTURN DEVICE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFPJAC2.0*;AEFPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEFT*JLONGITUDINAL ACTUATOR TRAVEL
THE MEASUREMENT OF THE LINEAR MECHANICAL MOTION OF THE ACUTATING SHAFT OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFTJLA2.0*;AEFTJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEFW*JLONGITUDINAL ACTUATOR EFFECTIVE ELECTRICAL STROKE LENGTH
THE PART OF THE TOTAL LONGITUDINAL TRAVEL OF THE ACTUATOR THAT PRODUCES A CHANGE IN OUTPUT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFWJAA2.0*;AEFWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and ABTD)
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and ABTB)
IF STYLE/REPLY CODE(s) AET WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and AJYP and AJYN and ADAG and AJYQ)
IF STYLE/REPLY CODE(s) AHF WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and AJYP and AJYN and AJYQ)
IF STYLE/REPLY CODE(s) AGM OR AJN WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AJYP and AJYN and AJYQ)
AXGYDMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDACC*;AXGYDAEZ$$DACQ*)
| Table 1 |
| Reply Code (AM39) | Reply |
| A | ANY ACCEPTABLE |
| ABC | BRACKET |
| ABH | CLAMP |
| ACX | CLAMP RING |
| ACR | FLANGE |
| ABL | FRICTION |
| AGM | LOCKING BUSHING |
| AEZ | PRINTED CIRCUIT |
| ABX | SHAFT |
| ABY | SLOT |
| ACY | SNAP SPRING |
| ADF | SNAP-IN |
| ANF | SPRING CLIP |
| AJN | STANDARD BUSHING |
| ACC | TAB |
| ACD | TERMINAL |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| BTW | UNTHREADED BUSHING |
| ACQ | UNTHREADED HOLE |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AKPV*AMOUNTING FACILITY QUANTITY
THE NUMBER OF MOUNTING FACILITIES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AKPVA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE, NF, NJ, NM, NS, BF OR UN WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (AJYQ)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC AJYP, YOU MUST NOT ANSWER MRC (AJYQ)
AJYP*DSCREW THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(AJYPDBF*;AJYPDSS$$DNF*)
| Table 1 |
| Reply Code (AH06) | Reply |
| BF | BSF |
| SM | ISO M |
| SS | ISO S |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
AJYN*JSCREW THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJYNJAA2.0*;AJYNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJYQ*BSCREW THREAD QUANTITY PER INCH
THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,INCLUDING INCOMPLETE THREADS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AJYQB2.0*;AJYQB2.0$$BM2.0*)
ADAG*JMOUNTING STUD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING STUD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAGJAA2.0*;ADAGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AAQ WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (AEEA and AEGH and AEGJ and CSDK and AEED)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAAQ*;CBBLDASF$$DAAN*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AAN | GROUNDED CONTACT ARM |
| ASG | HERMETICALLY SEALED |
| AAT | HUMIDITY PROOF |
| AAR | NONMETALLIC SHAFT |
| ASF | PANEL SEAL |
| AAP | PRESSURE MOUNTED TAP |
| AAS | SHAFT LOCKING DEVICE |
| CNW | SHAFT SEAL |
| AAQ | SWITCH |
IF STYLE/REPLY CODE(s) AA, AB OR AC WERE ENTERED FOR MRC AEEA, YOU MUST ANSWER STYLE/REPLY CODES(s) E FOR MRC (AEGH)
AEEA*DSWITCH TYPE
INDICATES THE TYPE OF SWITCH INCLUDED IN THE ITEM.
Enter the applicable reply code from the table below
(AEEADAF)
| Table 1 |
| Reply Code (AC82) | Reply |
| AA | PULL |
| AB | PUSH |
| AC | PUSH-PULL |
| AD | ROTARY |
| AE | SENSITIVE |
| AF | SLIDE |
| AG | TOGGLE |
AEGH*DSWITCH OPERATING POSITION
THE DEFINITIVE POSITIONAL POINT AT WHICH THE SWITCH OPERATES /STARTING WITH THE ACTUATOR IN EXTREME COUNTERCLOCKWISE POSITION AND MOVING CLOCKWISE FOR ROTARY ACTUATED RESISTORS;STARTING WITH ACTUATOR FULL RETRACTED /PUSHED IN/ FOR LONGITUDINALLY ACTUATED RESISTORS/. PLEASE USE MRC ARNH IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AEGHDA)
| Table 1 |
| Reply Code (AC97) | Reply |
| E | ANY POSITION OF ROTATION TRAVEL |
| D | END OF LINEAR MOVEMENT |
| B | END OF ROTATION |
| C | START OF LINEAR MOVEMENT |
| A | START OF ROTATION |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEGJ*DSWITCH CONTACT ARRANGEMENT
A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF A SWITCH.
Enter the applicable reply code from the table below
(AEGJDAN)
| Table 1 |
| Reply Code (AD85) | Reply |
| BF | DOUBLE POLE, DOUBLE THROW |
| BE | DOUBLE POLE, SINGLE THROW, NORMALLY CLOSED |
| BD | DOUBLE POLE, SINGLE THROW, NORMALLY OPEN |
| CT | DOUBLE POLE, SINGLE THROW, ONE OPEN, ONE CLOSED |
| AN | SINGLE POLE, DOUBLE THROW, THREE POSITIONS MAINTAINED |
| BG | SINGLE POLE, SINGLE THROW, NORMALLY CLOSED |
| AA | SINGLE POLE, SINGLE THROW, NORMALLY OPEN, BOTH POSITIONS MAINTAINED |
| CW | SINGLE POLE, SINGLE THROW, NORMALLY OPEN, ONE POSITION MOMENTARY |
CSDK*JSWITCH CURRENT TYPE AND RATING IN AMPS
INDICATES THE TYPE OF ELECTRICAL CURRENT AND THE CAPACITY FOR NORMAL OPERATION OF THE SWITCH,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSDKJAD2.0*;CSDKJAD2.0$$JAD2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AC | AC |
| AD | AC/DC |
| DC | DC |
AEED*BSWITCH VOLTAGE RATING IN VOLTS
THE VOLTAGE FOR WHICH THE SWITCH IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEEDB2.0*;AEEDB2.0$$BM2.0*)
IF STYLE/REPLY CODE(s) AAM WERE ENTERED FOR MRC TTQY, YOU MUST ANSWER MRC (AEHT and CQCM)
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAS2*;TTQYJAAS2$$JAAS3*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ABL | BINDING POST |
| ABM | BRACKET |
| ABN | CLAMP |
| ABP | CONCENTRIC |
| AAF | CONNECTOR, RECEPTACLE |
| ABR | EYELET |
| ABS | EYELET W/TAB |
| AAH | FERRULE |
| AMG | J-HOOK |
| AAM | PIN |
| ACH | PIN CLAMP |
| ACE | PIN, PREFORMED |
| ACR | PRINTED CIRCUIT |
| ABQ | SCREW |
| ABT | SCREW BASE |
| AAS | SOLDER STUD |
| ABW | SPARK PLUG |
| AHK | SPRING CLIP |
| AAT | STANDARD TUBE BASE |
| ABX | TAB W/SCREW |
| ABY | TAB W/WIRE LEAD |
| ABZ | TAB W/WIRE LEAD W/TAB |
| ABB | TAB, SOLDER LUG |
| ACA | THREADED BUSHING |
| ABD | THREADED STUD |
| ACB | TURRET |
| ACF | WIRE CLAMP |
| ACC | WIRE LEAD |
| ACD | WIRE LOOP |
| ACG | WIRE SLING |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEHT*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHTJAC2.0*;AEHTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQCM*JCENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL
THE CENTER TO CENTER DISTANCE BETWEEN THE CENTER TERMINAL AND THE OUTSIDE TERMINAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQCMJAB2.0*;CQCMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APXHDTERMINAL LOCATION
THE POSITION OF THE TERMINAL/S/ FOR MAKING CONNECTION TO AN ITEM.PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(APXHDDLJ)
| Table 1 |
| Reply Code (AJ91) | Reply |
| DMA | ALL ADJACENT SIDES FROM ADJACENT CONTROL |
| DMB | DUAL INLINE |
| ABT | FRONT END |
| DLZ | FRONT-REAR |
| DLP | LEFT ADJACENT SIDE SINGLE ROW |
| DLN | LEFT ADJACENT SIDE TWO ROWS |
| DLX | LONGITUDINALLY POSITIONED ON THE CIRCUMFERENCE |
| DLK | LOWER ADJACENT SIDE SINGLE ROW |
| DLJ | LOWER ADJACENT SIDE TWO ROWS |
| DLT | RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE |
| DLW | RADIALLY POSITIONED OVER MORE THAN HALF THE CIRCUMFERENCE |
| EAS | REAR ANGLED TO BOTTOM |
| CWG | REAR END |
| DLY | REAR-BOTTOM |
| DLQ | RIGHT ADJACENT SIDE SINGLE ROW |
| DLR | RIGHT ADJACENT SIDE TWO ROWS |
| DLS | RIGHT-LEFT ADJACENT SIDES |
| DLM | UPPER ADJACENT SIDE SINGLE ROW |
| DLL | UPPER ADJACENT SIDE TWO ROWS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AYQR*JCENTER TO CENTER DISTANCE BETWEEN TERMINAL ROWS
THE CENTER TO CENTER DISTANCE BETWEEN THE ROWS OF TERMINALS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYQRJAA2.0*;AYQRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) E WERE ENTERED FOR MRC AARG, YOU MUST ANSWER MRC (AARH)
AARGDRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDE)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
AARH*BRELIABILITY FAILURE RATE LEVEL IN PERCENT
THE RATE OF FAILURE DETERMINED UNDER SPECIFIED CONDITIONS TO ESTABLISH THE RELIABILITY OF AN ITEM,EXPRESSED IN PERCENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AARHB2.0)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDD)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDIRA000$DRHA000*;PRMTDIRA000$$DRHA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000F2.0*;PMWTJRTA000F2.0$JRTA000F2.0*;PMWTJRTA000F2.0$$JRTA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$JAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
BYDT*DBEARING TYPE
INDICATES THE TYPE OF BEARING PROVIDED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(BYDT3BHODAK*;BYDT3BHODAK$DAE*;BYDT3BHODAK$$DAE*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3BHO | SHAFT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH96) | Reply |
| AE | BALL |
| AU | BEARING |
| AK | SLEEVE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)