An item used as a component part of a support kit for small fragment set and mini fragment set.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED36717*)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AXNBJOUTSIDE THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE OUTSIDE OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXNBJAB2.0*;AXNBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZRWJTHREAD QUANTITY
THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. PLEASE USE MRC CQRN IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AZRWJBBJTEXT1234*)
| Table 1 |
| Reply Code (AJ40) | Reply |
| BBJ | PER INCH |
| BBK | PER MILLIMETER |
ABETJTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABETJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
BMCW*JMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS TO STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(BMCWJV2*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AASH*JMINIMUM TENSILE STRENGTH
THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AASHJV2*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
ALMEJMATERIAL HARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE MATERIAL WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALMEJRBB2.0*;ALMEJRBB2.0$$JRBB2.1*)
| Table 1 |
| Reply Code (AC26) | Reply |
| RB | ROCKWELL B |
| RC | ROCKWELL C |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASGDCASEHARDENING INDICATOR
INDICATES WHETHER OR NOT A FERROUS ALLOY OBJECT HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION OR CORE.
Enter the applicable reply code from the table below
(AASGDA)
| Table 1 |
| Reply Code (AA70) | Reply |
| A | CASEHARDENED |
| B | NOT CASEHARDENED |
IF STYLE/REPLY CODE(s) B1, B2, B4, B5, B6, B9, B10, B12, B13, B14, B15, B16, B17, B18, B19, B20, B21, B22, B23, B24, B25, B26, B29, B32, B37, B67, B68, B69, B70 OR B71 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU)
IF STYLE/REPLY CODE(s) B3 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and ASDB)
IF STYLE/REPLY CODE(s) B27 OR B28 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and ASDB)
IF STYLE/REPLY CODE(s) B7, B8, B60, B73 OR B75 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and AASV and ASDB)
IF STYLE/REPLY CODE(s) B11, B30, B45, B46, B47, B48, B79, B80, B81, B82, B83, B84, B85, B86, B87, B88, B89, B90 OR B91 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and ASDB)
IF STYLE/REPLY CODE(s) B34, B35, B38 OR B43 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and AATA)
IF STYLE/REPLY CODE(s) B36, B41, B44, B64, B65 OR B66 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AATA)
IF STYLE/REPLY CODE(s) B39 OR B40 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASM and AASU and AATA and ASDB)
IF STYLE/REPLY CODE(s) B31 OR B33 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and AASY)
IF STYLE/REPLY CODE(s) B42 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATA and ASDB)
IF STYLE/REPLY CODE(s) B49 OR B50 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AAST and AASU and AATA)
IF STYLE/REPLY CODE(s) B51 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and AASW and AATA)
IF STYLE/REPLY CODE(s) B52 OR B54 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AAST and AASU)
IF STYLE/REPLY CODE(s) B53 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AAST and AASU and AASW and AATA)
IF STYLE/REPLY CODE(s) B55, B56 OR B57 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and ASDB and AATC and AATD)
IF STYLE/REPLY CODE(s) B58, B63 OR B72 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and AATC and AATD)
IF STYLE/REPLY CODE(s) B59 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASN and AASP and AASU) or (AASL and AASN and AASQ and AASU)
IF STYLE/REPLY CODE(s) B61 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASN and AASQ and AASU and ASDB)
IF STYLE/REPLY CODE(s) B76 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASR and AASV and AASX)
IF STYLE/REPLY CODE(s) B77 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AASX)
IF STYLE/REPLY CODE(s) B78 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and AASV and ASDB and AATE)
AASKLHEAD STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HEAD.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AASKLB28)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BP10024 | B1 | BALL |
| BP10033 | B10 | BUTTON |
| BP10034 | B11 | SQUARE |
| BP10035 | B12 | FILLISTER |
| BP10036 | B13 | OVAL |
| BP10037 | B14 | ROOF |
| BP10038 | B15 | ROUND |
| BP10039 | B16 | TRUSS |
| BP10040 | B17 | WATERTIGHT |
| BP10041 | B18 | WEATHERTIGHT |
| BP10042 | B19 | FLAT |
| BP10025 | B2 | BEVEL |
| BP10043 | B20 | PAN |
| BP10044 | B21 | PAN NO. 2 |
| BP10045 | B22 | FLAT FILLISTER |
| BP10046 | B23 | MODIFIED PAN |
| BP10047 | B24 | UNDERCUT PAN NO. 2 |
| BP10048 | B25 | FLAT CHAMFER |
| BP10049 | B26 | RIBBED |
| BP10050 | B27 | ROUND WITH WRENCH FLATS CHAMFERED |
| BP10051 | B28 | ROUND WITH WRENCH FLATS |
| BP10052 | B29 | ROUND WEDGE |
| BP10026 | B3 | BLIND |
| BP10053 | B30 | SQUARE WEDGE |
| BP10054 | B31 | DEE CHAMFER |
| BP10055 | B32 | UNDERCUT UNIVERSAL |
| BP10056 | B33 | DEE |
| BP10057 | B34 | DISHED COUNTERSUNK |
| BP10058 | B35 | FILLISTER COUNTERSUNK |
| BP10059 | B36 | FLAT COUNTERSUNK |
| BP10060 | B37 | FLAT TOP ELEVATOR |
| BP10061 | B38 | FLAT COUNTERSUNK UNDERCUT |
| BP10062 | B39 | HEXAGON COUNTERSUNK |
| BP10027 | B4 | DOUBLE CHAMFER |
| BP10063 | B40 | HEXAGON COUNTERSUNK UNDERCUT |
| BP10064 | B41 | OVAL COUNTERSUNK |
| BP10065 | B42 | SQUARE COUNTERSUNK |
| BP10066 | B43 | OVAL COUNTERSUNK UNDERCUT |
| BP10067 | B44 | ROUND COUNTERSUNK |
| BP10068 | B45 | DISHED HEXAGON |
| BP10069 | B46 | DOUBLE HEXAGON |
| BP10070 | B47 | HEXAGON |
| BP10071 | B48 | CROWNED HEXAGON |
| BP10072 | B49 | FLAT COUNTERSUNK REVERSE KEYED |
| BP10028 | B5 | DRIVE |
| BP10073 | B50 | FLAT COUNTERSUNK REVERSE KEYED NO. 2 |
| BP10074 | B51 | FLAT COUNTERSUNK KEYED |
| BP10075 | B52 | SINGLE CHAMFER KEYED |
| BP10076 | B53 | FLAT COUNTERSUNK PARALLEL KEYED |
| BP10077 | B54 | FLAT KEYED |
| BP10078 | B55 | DOUBLE HEXAGON EXTENDED WASHER NO. 1 |
| BP10079 | B56 | HEXAGON EXTENDED WASHER |
| BP10080 | B57 | SQUARE EXTENDED WASHER |
| BP10081 | B58 | ROUND EXTENDED WASHER |
| BP10082 | B59 | SWIVEL HANDLE |
| BP10029 | B6 | FLUSH |
| BP10083 | B60 | SPADE |
| BP10084 | B61 | SLIDING HANDLE |
| BP10085 | B62 | WATERTIGHT HEXAGON |
| BP10086 | B63 | FILLISTER EXTENDED WASHER |
| BP10087 | B64 | BOILER PATCH NO. 1 |
| BP10088 | B65 | BOILER PATCH NO. 2 |
| BP10089 | B66 | BOILER PATCH NO. 3 |
| BP10090 | B67 | KNURLED NO. 1 |
| BP10091 | B68 | KNURLED NO. 2 |
| BP10092 | B69 | KNURLED NO. 3 |
| BP10030 | B7 | HOOK |
| BP10093 | B70 | KNURLED NO. 4 |
| BP10094 | B71 | KNURLED NO. 5 |
| BP10095 | B72 | KNURLED NO. 6 |
| BP10096 | B73 | TEE NO. 1 |
| BP10098 | B75 | TEE NO. 3 |
| BP10099 | B76 | TEE NO. 4 |
| BP10100 | B77 | TEE NO. 5 |
| BP10101 | B78 | TEE NO. 6 |
| BP10102 | B79 | THUMB NO. 1 |
| BP10031 | B8 | OFFSET SPADE |
| DR04099 | B80 | THUMB NO.2 |
| BP10104 | B81 | THUMB NO. 3 |
| BP10105 | B82 | THUMB NO. 4 |
| BP10106 | B83 | THUMB NO. 5 |
| BP10107 | B84 | THUMB NO. 6 |
| BP10108 | B85 | THUMB NO. 7 |
| BP10109 | B86 | THUMB NO. 8 |
| BP10110 | B87 | THUMB NO. 9 |
| BP10111 | B88 | WING NO. 1 |
| BP10112 | B89 | WING NO. 2 |
| BP10032 | B9 | BINDING |
| BP10113 | B90 | WING NO. 3 |
| BP10114 | B91 | WING NO. 4 |
AASL*JHEAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASLJAA2.0*;AASLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASM*JBOTTOM COUNTERSINK DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASMJAB2.0*;AASMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASN*JHANDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASNJAC2.0*;AASNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASP*JHANDLE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HANDLE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASPJAB2.0*;AASPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASQ*JHANDLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HANDLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASQJAA2.0*;AASQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASR*JHEAD INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASRJAC2.0*;AASRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAST*JKEY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASTJAA2.0*;AASTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASU*JHEAD HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEAD,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASUJAC2.0*;AASUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASV*JHEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASVJAA2.0*;AASVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASW*JKEY PROJECTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASWJAC2.0*;AASWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASX*JTEE BOLT CYLINDRICAL HEAD DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASXJAA2.0*;AASXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJAA2.0*;AASYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATC*JEXTENDED WASHER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATCJAB2.0*;AATCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATD*JEXTENDED WASHER THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATDJAA2.0*;AATDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAC2.0*;ASDBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATA*BCOUNTERSINK ANGLE IN DEG
THE INCLUDED ANGLE OF THE COUNTERSINK,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AATAB2.0)
AATE*BCHAMFER ANGLE IN DEG
THE MEASUREMENT OF THE CHAMFER ANGLE,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AATEB2.0)
BZGFLRECESSED DRIVE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RECESSED DRIVE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BZGFLC2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BP10115 | C1 | CROSS RECESS TYPE 1 |
| BP10124 | C10 | TORQUE |
| BP10125 | C11 | CROSS RECESS TYPE 1A |
| BP10126 | C12 | CLUTCH TYPE 1 |
| BP10127 | C13 | CLUTCH TYPE 11 |
| BP10128 | C14 | ONE WAY |
| BP10129 | C15 | SLOT |
| BP10130 | C16 | FOUR SPANNER |
| BP10131 | C17 | SOCKET |
| BP10132 | C18 | FOUR SPLINE |
| BP10116 | C2 | CROSS RECESS TYPE 11 |
| BP10117 | C3 | CROSS RECESS TYPE 111 |
| BP10118 | C4 | DOUBLE HEXAGON |
| BP10119 | C5 | SOCKET |
| BP10120 | C6 | RECESSED TYPE 1 |
| BP10121 | C7 | SIX SPLINE |
| BP10122 | C8 | TORQUE SET |
| BP10123 | C9 | HIGH-TORQUE |
BBDT*DPOINT TYPE
INDICATES THE TYPE OF POINT(S) PROVIDED ON THE ITEM.
Enter the applicable reply code from the table below
(BBDTDAGF)
| Table 1 |
| Reply Code (AJ44) | Reply |
| AAB | BALL |
| AFY | BAYONET |
| AFZ | BEVEL |
| AGA | BLUNT |
| AGB | BONE INSULATED |
| AGC | BOTH BLUNT |
| AGD | BOTH SHARP |
| AGE | CLOVERLEAF |
| AGF | CONE |
| AGG | CYLINDRICAL |
| AHH | DIAMOND |
| APB | DIAMOND POINT, BOTH ENDS |
| AGH | DOG |
| AGJ | FLAT STAR |
| AGK | FLAT WIRE |
| AGL | FLUTED |
| AGM | KNIFE |
| AAA | KNOB |
| AGN | NEEDLE |
| AGP | OLIVARY POINTED |
| AGQ | ONE BLUNT |
| AGR | ONE SHARP |
| AGS | PILOT |
| APC | PLAIN SHANK, DIAMOND POINT |
| APD | PLAIN SHANK, TROCAR POINT |
| AGT | PROBE HOOK |
| AGW | PROBE POINTED |
| AGX | ROUND BLUNT |
| AAU | ROUND LOOP |
| AGY | ROUND WIRE |
| AGZ | SAW |
| AHA | SHARP |
| AHB | STANDARD |
| AHC | TAPERED STAR |
| APE | THREE SIDED SHANK, DIAMOND POINT |
| APF | THREE SIDED SHANK, TROCAR POINT |
| AHD | TROCAR |
| APG | TROCAR POINT, BOTH ENDS |
| AHE | TROCAR POINTED |
| AHF | TWIST DRILL |
| AJT | VERTICAL |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDPDA000$DPTA000*;PRMTDPDA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAZA000E2.0*;PMWTJAZA000E2.0$$JAZA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDPCAM00*;MATT3AEEDPCAM00$DSTA000*;MATT3AEEDPCAM00$$DSTA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| TTB000 | TITANIUM |
SFTTDSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDANA000*;SFTT3AEEDANA000$DANA000*;SFTT3AEEDANA000$$DANA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information