A gas discharge lamp which emits radiation in the form of a cathode glow from a hollow cathode closed at one end. It is usually used in atomic absorption spectrophotometers.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED33287*)
CRPSLBASE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BASE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CRPSLA1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BI10001 | A1 | SPECIAL MINIATURE, ONE AND HALF TURN THREAD |
| BI10009 | A10 | GUNSIGHT SCREW |
| DR01191 | A100A | TWO PIN PREFOCUS |
| DR01192 | A100B | GY16 |
| BI10103 | A101 | 2-PIN |
| BI10104 | A102 | 2-PIN VENTED |
| BI10007 | A103 | E27-3 FIN PREFOCUS |
| DR00522 | A104A | SPECIAL 8BA THREAD |
| DR00523 | A104B | SPECIAL 10BA THREAD |
| DR00524 | A104C | SPECIAL 1.7X0.35MM THREAD |
| DR00525 | A104D | SPECIAL 2.2X0.45MM THREAD |
| BI10017 | A105 | S12S |
| BI10027 | A106 | BA7S/11 |
| BI10025 | A107 | BA20S (BOSCH) |
| BI10026 | A108 | BA20D (BOSCH) |
| BI10028 | A109 | BA21S-3 (120*) |
| BI10196 | A11 | SURGICAL SCREW |
| BI10029 | A110 | BA21D-3 (120*) |
| BI10030 | A111 | B9.5S/11 (WOOTTON BAYONET) |
| BI10033 | A112 | B22D-3(90*/135*)/25x26 |
| DR03473 | A113A | B22D-54 (Ceramic) |
| DR03474 | A113B | B22D-68 (Ceramic) |
| BI10035 | A114 | BY22D (For Sodium Lamps) |
| BI10040 | A115 | P28D (DC Medium Prefocus |
| BI10041 | A116 | P14.5S |
| DR01167 | A117A | P38S WITH THREE FLATS |
| DR01168 | A117B | P46S WITH THREE FLATS |
| BI10048 | A118 | P36S - (BPF SC) |
| BI10049 | A119 | P36D - (BPF DC) |
| BI10050 | A120 | PK22S |
| BI10051 | A121 | P45T-41 |
| BI10052 | A122 | P18S |
| BI10053 | A123 | P43T-38 |
| BI10054 | A124 | PG22-6.35 |
| BI10085 | A125 | T4.6 |
| BI10086 | A126 | T5.5K |
| BI10087 | A127 | T5.5 |
| BI10088 | A128 | T5.5K M/ |
| BI10089 | A129 | T5.8 |
| DR00526 | A12A | MIDGET FLANGED |
| DR00527 | A12B | SPECIAL MICRO MINIATURE FLANGED |
| DR00528 | A12C | SPECIAL SUB-MIDGET FLANGED |
| DR00529 | A12D | SUB-MIDGET FLANGED |
| BI10014 | A13 | SINGLE CONTACT MINIATURE FLANGED |
| BI10090 | A130 | T6.6 |
| BI10091 | A131 | T6.5 |
| BI10092 | A132 | T6.8 |
| BI10093 | A133 | T7 |
| BI10094 | A134 | SIDE CLIPS W/COLOURED END |
| BI10095 | A135 | SIDE CLIPS |
| BI10123 | A136 | FA6 - (SINGLE PIN FOR FLUORESCENT) |
| BI10126 | A137 | FA4 - (SINGLE PIN FOR TUBULAR LAMPS) |
| BI10133 | A138 | FC6.4-0.8 |
| BI10135 | A139 | G16T/23 X 22 |
| BI10015 | A14 | DOUBLE CONTACT MINIATURE FLANGED |
| BI10139 | A140 | X511 |
| BI10141 | A141 | FLASH CUBE |
| BI10140 | A142 | W10.6 x 8.5D - (PHOTO FLASH BULB) |
| BI10107 | A143 | G19 (B1-PIN) |
| BI10198 | A144 | FLASH BAR |
| BI10143 | A145 | FLIP FLASH |
| BI10142 | A146 | MAGICUBE |
| DR00530 | A15A | MINIATURE BAYONET PINLESS |
| DR00531 | A15B | SINGLE CONTACT BAYONET PINLESS |
| DR00532 | A15C | SINGLE CONTACT CANDELABRA PINLESS |
| BI10018 | A16 | DOUBLE CONTACT BAYONET PINLESS |
| DR00533 | A17A | MIDGET GROOVED |
| DR00534 | A17B | S5.5S - (Midget Groove) |
| DR00535 | A17C | S5.7S8 |
| DR00541 | A18A | MINIATURE BAYONET |
| DR00542 | A18B | SINGLE CONTACT BAYONET CANDELABRA |
| DR00543 | A18C | SINGLE CONTACT BAYONET CANDELABRA EXPORT |
| DR00544 | A18D | BA9S/13 - (MCC) |
| DR00545 | A18E | BA9S/14 - (MCC) |
| DR00546 | A18F | B15S/19 - (SCC) |
| DR00547 | A18G | BA15S - (SCC) |
| DR00548 | A18H | B22s/22 - (BC) |
| DR00716 | A19A | DOUBLE CONTACT BAYONET CANDELABRA |
| DR00717 | A19B | DOUBLE CONTACT BAYONET CANDELABRA EXPORT |
| DR00718 | A19C | B15D/19 - (SBC) |
| DR00719 | A19D | BA15D - (SBC) |
| DR00720 | A19E | B22D/22 - (BC) |
| DR00721 | A20A | SINGLE CONTACT BAYONET CANDELABRA INDEXING |
| DR00722 | A20B | BAY15S(SCC Indexing) |
| DR00723 | A21A | DOUBLE CONTACT BAYONET CANDELABRA INDEXING |
| DR00724 | A21B | BAY15D (SBC Indexing) |
| BI10023 | A22 | THREE CONTACT MEDIUM BAYONET |
| DR00725 | A23A | MINIATURE BAYONET SKIRTED |
| DR00726 | A23B | SINGLE CONTACT MEDIUM BAYONET EXPORT |
| DR00727 | A23C | B22S/25X26 (BC Skirted) |
| DR00728 | A23D | B15S/24X17 (SCC Skirted) |
| DR00729 | A23E | B15S/27X22 (SCC Skirted) |
| DR00730 | A23F | B15S/29X26 (SCC Skirted) |
| DR00731 | A24A | DOUBLE CONTACT BAYONET CANDELABRA SKIRTED |
| DR00732 | A24C | B15D/24X17 (SBC Skirted) |
| DR00733 | A24D | B15D/27X22 (SBC Skirted) |
| DR00734 | A24E | B15D/29X26 (SBC Skirted) |
| DR00735 | A24F | B22D/25X26 (BC Skirted) |
| BI10036 | A25 | SINGLE CONTACT CANDELABRA PREFOCUS |
| BI10037 | A26 | DOUBLE CONTACT CANDELABRA PREFOCUS |
| BI10038 | A27 | UNTHREADED CYLINDER WITH SCREW TERMINAL |
| DR00736 | A28A | MEDIUM PREFOCUS |
| DR00737 | A28B | MOGUL PREFOCUS |
| DR00738 | A28C | P28S/24 - (MEDIUM PREFOCUS) |
| DR00739 | A28D | P40S/41 - (Large Prefocus) |
| DR00740 | A28E | P28S/33 (Medium Prefocus) |
| DR00741 | A28F | P40S/55 (Large Prefocus) |
| BI10042 | A29 | DOUBLE CONTACT MEDIUM RING |
| DR01584 | A2A | ADMEDIUM SCREW |
| DR01585 | A2B | CANDELABRA SCREW |
| DR01586 | A2C | INTERMEDIATE SCREW |
| DR01587 | A2E | MEDIUM SCREW |
| DR01588 | A2F | MEDIUM SCREW EXPORT |
| DR01589 | A2G | MIDGET SCREW |
| DR01590 | A2H | MINIATURE SCREW |
| DR01591 | A2J | MOGUL SCREW |
| DR01592 | A2K | MOGUL SCREW EXPORT |
| DR01593 | A2L | E5/9 - (LES) |
| DR01594 | A2M | E10/12 |
| DR01614 | A2N | E10/13 - (MES) |
| DR01615 | A2P | E12/15 |
| DR01616 | A2Q | E14/20 - (SES) |
| DR01617 | A2R | E17/20 |
| DR04094 | A2S | E26/24 |
| DR01619 | A2T | E27/25 - (ES) |
| DR01620 | A2U | E27/27 - (ES) |
| DR01621 | A2V | E39/41 |
| DR01622 | A2W | E40/41 - (GES) |
| DR01623 | A2X | E40/45 - (GES) |
| BI10043 | A30 | BELL AND HOWELL LARGE INDEXING RING |
| BI10044 | A31 | LARGE INDEXING RING |
| BI10045 | A32A | VENTILATED LARGE INDEXING RING |
| DR01165 | A33A | BELL AND HOWELL SMALL INDEXING RING |
| DR01166 | A33B | P38S (Small Bell and Howell) |
| BI10055 | A34 | EXTENDED MOGUL END PRONG WITH CERAMIC BLOCK |
| BI10056 | A35 | MOGUL END PRONG WITH CERAMIC BLOCK |
| BI10057 | A36 | MOGUL END PRONG |
| BI10058 | A37 | MEDIUM SIDE PRONG |
| BI10059 | A38 | TWO CONTRACT LUGS (not contact) |
| BI10060 | A39 | TWO SLIP-ON TERMINALS |
| DR00513 | A3A | ADMEDIUM SCREW SKIRTED |
| DR00514 | A3B | CANDELABRA SCREW SKIRTED |
| DR00515 | A3C | MEDIUM SCREW SKIRTED |
| DR00516 | A3D | E12/20X15/CANDELABRA SCREW |
| DR00517 | A3E | E5/15X6 (LES Skirted) |
| DR00518 | A3F | E10/19X13 (MES Skirted) |
| DR00519 | A3G | EP10/14X11 (Prefocus MES) |
| DR00520 | A3H | E14/23X15 (SES Skirted) |
| DR00521 | A3J | E14/25X17 (SES Skirted) |
| DR00536 | A3K | E27/51X39 (ES Skirted) |
| BI10061 | A40 | TWO SCREW TERMINALS |
| BI10062 | A41 | THREE SLIP-ON TERMINALS |
| BI10063 | A42 | THREE SCREW TERMINALS |
| BI10064 | A43 | THREE CONTACT LUGS |
| BI10065 | A44 | FERRULE CONTACT |
| BI10066 | A45 | THREE WIRE LEADS |
| BI10067 | A46 | FLEXIBLE STRAP |
| DR01169 | A47A | MINIATURE CAP CONICAL END |
| DR01170 | A47B | SV8.5/8 (Small Festoon) |
| DR01171 | A47C | SV8.5/5 (Small Festoon) |
| DR01172 | A47D | SV8.5/6.5 (Small Festoon) |
| DR01173 | A47E | SV7/6.8(Miniature Festoon) |
| DR01174 | A47F | SV7/8 (MINIATURE FESTOON) |
| BI10070 | A48 | MINIATURE CAP CYLINDRICAL END |
| BI10069 | A49 | SPADE SINGLE CONTACT TERMINAL |
| DR00473 | A4A | THREE CONTACT MEDIUM SCREW |
| DR00474 | A4B | THREE CONTACT MOGUL SCREW |
| DR00475 | A4C | E26D |
| BI10004 | A5 | MINI-CAN |
| BI10071 | A50 | METAL SLEEVE WITH FLEXIBLE WIRE LEADS |
| BI10072 | A51 | CERAMIC TUBULAR WITH FLEXIBLE WIRE LEADS |
| BI10073 | A52 | RECESSED SINGLE CONTACT |
| BI10074 | A53 | RECTANGULAR RECESSED SINGLE CONTACT |
| BI10075 | A54 | BRASS FERRULE |
| BI10076 | A55 | INSULATED SLEEVE WITH FLEXIBLE WIRE LEADS |
| BI10077 | A56 | FLEXIBLE WIRE LEADS |
| BI10078 | A57 | SPECIAL SLEEVE (AIRCRAFT) |
| BI10079 | A58 | DOUBLE SLIDE |
| BI10080 | A59 | TELEPHONE SLIDE NUMBER ONE |
| BI10081 | A60 | TELEPHONE SLIDE NUMBER TWO |
| BI10082 | A61 | TELEPHONE SLIDE SPECIAL |
| BI10083 | A62 | TELEPHONE SLIDE NUMBER THREE |
| BI10084 | A63 | TELEPHONE SLIDE NUMBER FIVE |
| BI10096 | A64 | SUB-MINIATURE TWO PIN |
| DR01175 | A65A | MINIATURE TWO PIN |
| DR01176 | A65B | G4 NONE |
| DR01177 | A65C | G6.35-15 |
| DR01178 | A65D | G6.35-20 |
| DR01179 | A65E | G6.35-25 |
| DR01180 | A65F | G6.35-30 |
| DR01181 | A65G | GX 6.35-15 |
| DR01182 | A65H | GX 6.35-20 |
| DR01183 | A65J | GX 6.35-25 |
| DR01184 | A65K | GX 6.35-30 |
| DR01185 | A65L | GY 6.35-15 |
| DR01186 | A65M | GY 6.35-20 |
| DR01187 | A65N | GY 6.35-25 |
| DR01188 | A65P | GY 6.35-30 |
| BI10097 | A66 | CARTRIDGE TWO PIN POLARIZED |
| DR01189 | A67A | MEDIUM BIPOST |
| DR01190 | A67B | G22 |
| DR01283 | A68A | MOGUL BIPOST |
| DR01284 | A68B | G 38 |
| BI10106 | A69 | LARGE THREE PIN |
| DR00469 | A6A | SPECIAL NO. 10-64 THREAD |
| DR00470 | A6B | SPECIAL 5/32 WHIT THREAD |
| DR00471 | A6C | SPECIAL 4X0.07MM THREAD |
| DR00472 | A6D | SPECIAL 2BA THREAD |
| DR01285 | A70A | MEDIUM FOUR PIN |
| DR01286 | A70B | SMALL FOUR PIN |
| DR01287 | A71A | FOUR PIN INDEXING |
| DR01288 | A71B | G17Q-7-FOUR PIN INDEXING |
| DR01289 | A71C | GX17Q-7-FOUR PIN INDEXING |
| DR01290 | A71D | GY17Q-7-FOUR PIN INDEXING |
| BI10110 | A72 | LOCKING FOUR PIN |
| BI10111 | A73 | OVAL SMALL FOUR PIN (GERMICIDAL) |
| DR03475 | A74A | MEDIUM FIVE PIN |
| DR03476 | A74B | SMALL FIVE PIN |
| BI10113 | A75 | GIANT FIVE PIN |
| BI10114 | A76 | SPECIAL FIVE PIN |
| DR03477 | A77A | DISK WITH THREE SOLDERING PINS,1-1/8 INCH DIAMETER |
| DR03478 | A77B | DISK WITH THREE SOLDERING PINS,1-3/8 INCH DIAMETER |
| BI10116 | A78 | DISK WITH THREE WIRE LEADS |
| BI10117 | A79 | OCTAL THREE PIN |
| DR00476 | A7A | KNURLED SCREW (KOLLSMAN) |
| DR00477 | A7B | KOLLSMAN SCREW |
| DR00478 | A7C | SPECIAL KOLLSMAN SCREW |
| DR00479 | A7D | INSULATED KOLLSMAN SCREW |
| BI10010 | A8 | SPECIAL 952 SCREW WITH DIMMER SLEEVE |
| BI10118 | A80 | OCTAL FIVE PIN |
| BI10119 | A81 | DISK LUMALINE |
| BI10120 | A82 | MINIATURE PINLESS (AIRCRAFT) |
| BI10121 | A83 | SINGLE PIN (FLUORESCENT) |
| DR01291 | A84A | MEDIUM BIPIN (FLUORESCENT) |
| DR01292 | A84B | MINIATURE BIPIN (FLUORESCENT) |
| DR01293 | A84C | MOGUL BIPIN (FLUORESCENT) |
| DR01294 | A85A | 4-PIN CIRCULAR (FLUORESCENT) |
| DR01295 | A85B | G 10Q(4 PIN FOR CIRCULAR FLUORESCENT) |
| BI10125 | A86 | RECESSED DOUBLE CONTACT (FLUORESCENT) |
| BI10127 | A87 | SINGLE PIN FLUTED (FLUORESCENT) |
| BI10128 | A88 | THREE PRONG AND TWO PRONG (FLUORESCENT) |
| DR01296 | A89A | GLASS GROOVE |
| DR01297 | A89B | W3.3X10.4D (GLASS GROOVE) |
| DR01459 | A90A | WEDGE |
| DR01460 | A90B | W2.1X9.5D (WEDGE) |
| DR01461 | A90C | W2X4.6D (WEDGE) |
| BI10131 | A91 | TAB |
| BI10197 | A92 | SURGICAL FLANGE, STYLE 1 |
| BI10134 | A93 | SURGICAL FLANGE, STYLE 2 |
| BI10132 | A94 | MOUNTING LUGS AND BEADED WIRE LEADS |
| BI10136 | A95 | DOUBLE INTERMEDIATE SCREW |
| BI10137 | A96 | WIRE LEADS, DOWN |
| BI10138 | A97 | WIRE LEADS, UP |
| BI10098 | A98 | WIRE WRAP TERMINAL |
| DR01193 | A99A | MEDIUM TWO PIN |
| DR01194 | A99B | G5.3 |
| DR01195 | A99C | G9.5 |
| DR01196 | A99D | GX 9.5 |
| DR01197 | A99E | GY 9.5 |
| DR00480 | A9A | SPECIAL 952 SCREW |
| DR00481 | A9B | SPECIAL 953 SCREW |
CSJWABULB DESIGNATOR
A DESIGNATION WHICH INDICATES THE SHAPE AND SIZE OF THE BULB.
Enter the alpha-numeric reply with a minimum of one character.
(CSJWAR6)
IF STYLE/REPLY CODE(s) B1, B3, B4, B5, B6, B7, B8, B9, B11, B12, B13, B14, B15, B16, B17, B18, B19, B20, B21, B22, B24, B25, B26, B27, B30, B31, B32, B33, B34, B38 OR B39 WERE ENTERED FOR MRC CRSK, YOU MUST ANSWER MRC (ABHP)
IF STYLE/REPLY CODE(s) B29 WERE ENTERED FOR MRC CRSK, YOU MUST ANSWER MRC (ADAV)
CRSKLBULB STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BULB.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CRSKLB4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BI10144 | B1 | A (ARBITRARY DESIGNATION) |
| BI10152 | B11 | GA (COMBINATION OF G AND A SHAPES) |
| BI10153 | B12 | GG (GLASS GLOBULAR) |
| BI10154 | B13 | GT (GLOBULAR TUBULAR) |
| BI10155 | B14 | GTL (GLOBULAR, TUBULAR, LENS END) |
| BI10156 | B15 | P (PEAR) |
| BI10157 | B16 | PAR (PARABOLIC, ALUMNIZED REFLECTOR) |
| BI10158 | B17 | PAR (PARABOLIC, ALUMINIZED REFLECTOR) |
| BI10160 | B18 | TD (TUBULAR DENTED) |
| BI10161 | B19 | PS (PEAR SHAPE, STRAIGHT NECK) |
| BI10162 | B20 | R (REFLECTOR) |
| BI10163 | B21 | RP (ARBITRARY DESIGNATION) |
| BI10164 | B22 | S (STRAIGHT SIDE) |
| BI10165 | B24 | SL (SLIDE LENS) |
| BI10166 | B25 | T (TUBULAR) |
| BI10167 | B26 | T ("U" SHAPED TUBULAR) |
| BI10169 | B27 | T (TUBULAR) |
| BI10168 | B29 | T (CIRCULAR) |
| BI10145 | B3 | B (ARBITRARY DESIGNATION) |
| BI10170 | B30 | TL (TUBULAR, LENS END) |
| BI10171 | B31 | IT (TWIN TUBULAR) |
| BI10172 | B32 | GT (GLOBULAR, TUBULAR) |
| BI10173 | B33 | BT (BULGED TUBULAR) |
| BI10159 | B34 | MR (ARBITARY DESIGNATION FOR LAMP WITH INTEGRAL REFLECTOR) |
| BI10174 | B35 | CUBE |
| BI10175 | B36 | HORIZONTAL ARRAY |
| BI10176 | B37 | VERTICAL ARRAY |
| BI10177 | B38 | REC (RECTANGULAR, ALUMINIZED REFLECTOR) |
| BI10178 | B39 | ER ELLIPTICAL REFLECTOR |
| BI10146 | B4 | BT (BULGED TUBULAR) |
| BI10147 | B5 | C (CONE) |
| BI10148 | B6 | E (ELIPTICAL) |
| BI10149 | B7 | F (FLAME) |
| BI10150 | B8 | FE (FLAT END) |
| BI10151 | B9 | G (GLOBULAR) |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFSC*JWIRE LEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A WIRE LEAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFSCJAC2.0*;AFSCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
TTQY*JTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAF2*;TTQYJAAF2$$JAAF3*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ACN | CONNECTOR, PLUG |
| AAF | CONNECTOR, RECEPTACLE |
| AAM | PIN |
| AFF | SOLDER LUG |
| AEK | SOLDERLESS LUG |
AEVV*JBULB DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BULB,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVVJAA2.0*;AEVVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGDVDEMITTED LIGHT CHARACTERISTIC
THE CHARACTERISTIC OF THE RADIANT ENERGY GENERATED BY THE LAMP WITHIN OR ADJACENT TO THE VISIBLE SPECTRUM OF LIGHT.
Enter the applicable reply code from the table below
(AGDVDGR0001)
| Table 1 |
| Reply Code (AD06) | Reply |
| AM0000 | AMBER |
| AM0001 | AMBER, CLOUDY |
| AM0005 | AMBER, DARK |
| AM0003 | AMBER, LIGHT |
| AM0002 | AMBER, NATURAL |
| AM0007 | AMBER, NATURAL DARK |
| AM0006 | AMBER-ORANGE |
| BL0000 | BLACK |
| BL0002 | BLACK, BLUE |
| MS0000 | BLACKLIGHT |
| BU0000 | BLUE |
| BU0055 | BLUE GREEN |
| BU0001 | BLUE, AVIATION, MIL-C-25050 TYPE 1 |
| BU0005 | BLUE, DARK |
| BU0026 | BLUE, LIGHT |
| BU0006 | BLUE, MOONLIGHT |
| BU0007 | BLUE, NATURAL |
| BU0003 | BLUE-VIOLET |
| BU0004 | BLUE-WHITE |
| CL0001 | COLORLESS |
| MS0001 | DAYLIGHT |
| GR0003 | EMERALD |
| RE0040 | FLAME |
| MS0002 | FLAMETINT |
| GL0000 | GOLD |
| GR0000 | GREEN |
| GR0001 | GREEN, AVIATION, MIL-C-25050 TYPE 1 |
| GR0149 | GREEN, COOL |
| GR0002 | GREEN, IDENTIFICATION, MIL-C-25050 TYPE 2 |
| GR0032 | GREEN, LIGHT |
| GR0004 | GREEN, NATURAL |
| GR0150 | GREEN, VEGETABLE |
| GR0042 | GREEN, YELLOW |
| NR0000 | INFRARED |
| VY0000 | IVORY |
| NA0000 | NATURAL |
| MS0041 | OPAL |
| RG0000 | ORANGE |
| RG0001 | ORANGE-RED |
| PK0000 | PINK |
| PK0001 | PINK, DAWN |
| PK0002 | PINK, SURPRISE |
| PU0000 | PURPLE |
| RE0000 | RED |
| RE0002 | RED, AVIATION, MIL-C-25050 TYPE 1 |
| RE0003 | RED, IDENTIFICATION, MIL-C-25050 TYPE 2 |
| RE0006 | ROSE |
| RE0020 | RUBY |
| RE0115 | RUBY, DARK |
| RE0005 | RUBY, NATURAL |
| RE0116 | RUBY, NATURAL DARK |
| MS0004 | STRAW |
| MS0005 | SUNLIGHT |
| UV0000 | ULTRAVIOLET |
| WH0000 | WHITE |
| WH0002 | WHITE, AVIATION, MIL-C-25050 TYPE 1 |
| WH0005 | WHITE, COOL |
| WH0059 | WHITE, COOL, SUPER DELUXE |
| WH0058 | WHITE, DELUXE |
| WH0006 | WHITE, DELUXE COOL |
| WH0007 | WHITE, DELUXE WARM |
| WH0065 | WHITE, DESIGN |
| WH0004 | WHITE, LUNAR |
| WH0001 | WHITE, LUNAR IDENTIFICATION, MIL-C-25050 TYPE 2 |
| WH0008 | WHITE, SOFT |
| WH0012 | WHITE, TRANSLUCENT |
| WH0009 | WHITE, WARM |
| YE0000 | YELLOW |
| YE0002 | YELLOW, AVIATION, MIL-C-25050 TYPE 1 |
| YE0012 | YELLOW, DARK |
| YE0003 | YELLOW, IDENTIFICATION, MIL-C-25050 TYPE 2 |
| YE0018 | YELLOW, LIGHT |
| YE0049 | YELLOW-GREEN |
CTGFDFILLING GAS TYPE
INDICATES THE TYPE OF GAS WITH WHICH THE ITEM IS FILLED.
Enter the applicable reply code from the table below
(CTGFDD*;CTGFDE$$DG*)
| Table 1 |
| Reply Code (AE50) | Reply |
| B | ARGON |
| G | HALOGEN |
| F | HELIUM |
| D | NEON |
| E | XENON |
AFSMDLIGHT INTENSITY LEVEL
THE LEVEL OF BRIGHTNESS OF THE LIGHT FLUX PRODUCED BY THE ITEM.
Enter the applicable reply code from the table below
(AFSMDG)
| Table 1 |
| Reply Code (AE25) | Reply |
| B | HIGH |
| N | NOT RATED |
| G | STANDARD |
AFSQJCIRCUIT VOLTAGE RATING IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE OF THE CIRCUIT IN WHICH THE ITEM IS DESIGNED TO BE USED,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFSQJA2.0*;AFSQJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BDWWJWATTAGE RATING
THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDWWJAT2.0*;BDWWJAT2.0$$JAT2.1*)
| Table 1 |
| Reply Code (AB49) | Reply |
| BC | KILOWATTS |
| AT | WATTS |
CTNBJRESISTOR RATING AND LOCATION
THE VALUE AND LOCATION OF THE RESISTOR REQUIRED TO CONTROL THE CURRENT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTNBJZZEXT2.0*)
| Table 1 |
| Reply Code (AN86) | Reply |
| KZ | KILOHMS |
| ZZ | OHMS |
| Table 2 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC CWBF, YOU MUST ANSWER MRC (AFSV)
CWBFDRATED AVERAGE LIFE
A TERM DENOTING THE MEASUREMENT USED TO INDICATE THE AVERAGE LIFE OF THE ITEM.
Enter the applicable reply code from the table below
(CWBFDN)
| Table 1 |
| Reply Code (AE52) | Reply |
| B | HOURS |
| D | INDEFINITE LONG |
| N | NOT RATED |
AFSV*BAVERAGE LIFE RATING IN HOURS
THE NUMERIC VALUE INDICATING THE AVERAGE LIFE EXPECTANCY FOR WHICH THE ITEM IS RATED,EXPRESSED IN HOURS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AFSVB2.0*;AFSVB2.0$$BM2.0*)
IF STYLE/REPLY CODE(s) P WERE ENTERED FOR MRC RADC, YOU MUST ANSWER MRC (RADD)
RADC*DRADIOACTIVE CONTENT
AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS.
Enter the applicable reply code from the table below
(RADCDP)
| Table 1 |
| Reply Code (AN54) | Reply |
| P | CONTAINS RADIOACTIVE MATERIAL |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCNY*;CBBLDCNZ$$DBFJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BFN | CARBON FILAMENT |
| BFJ | FILAMENT SHIELDING |
| CNY | FLUTED LENS |
| CNZ | FRESNEL LENS |
| BFK | HEAT RESISTANT GLASS |
| BFL | PREAGED LAMP |
| FNY | ROHS DIRECTIVE COMPLIANCE |
| BFM | WATERPROOF TERMINALS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDLQ*;ENACDGE$$DHL*)
| Table 1 |
| Reply Code (EN02) | Reply |
| LQ | COMPACT FLUORESCENT LAMP (CFL) LIGHT BULBS - ENERGY STAR-LIGHTING - ENERGY EFFICIENT PRODUCTS |
| HL | ENERGY EFFICIENT - FEMP - LIGHTING - COMPACT FLUORESCENT LAMPS |
| GE | FLUORESCENT LAMPS - FEMP-LIGHTING - ENERGY EFFICIENT PRODUCTS |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
BGTB*HSTORAGE FACILITY
THE STORAGE FACILITY STANDARDS ESTABLISHED TO ASSURE THE SERVICEABILITY OF SUPPLIES IN STORAGE.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below.
(BGTBHBAWAC2.0*;BGTBHBAWAC2.0$$HBAWAC2.1*)
| Table 1 |
| Reply Code (AN11) | Reply |
| D | ALTERNATE |
| B | MANDATORY |
| C | PREFERRED |
| Table 2 |
| Reply Code (AM81) | Reply |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
| Table 3 |
| Reply Code (AN12) | Reply |
| AC | CONTROLLED HUMIDITY |
| AD | FLAMMABLE |
| AB | GENERAL PURPOSE |
| AE | SECURITY |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAH*;BBRJDAE$$DAE*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AE | FRAGILE |
| AH | RADIOACTIVE |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
RADD*JRADIONUCLIDES DATA
THE NAME AND AMOUNT OF THE RADIONUCLIDE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(RADDJJHAAHQ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| JF | CURIES |
| JH | MICROCURIES |
| JG | MILLICURIES |
| Table 2 |
| Reply Code (AN55) | Reply |
| AAAB | ACTINIUM (89) AC-227 |
| AAAC | ACTINIUM (89) AC-228 |
| AAAD | AMERICIUM (95) AM-241 |
| AAAE | AMERICIUM (95) AM-243 |
| AAAF | ANTIMONY (51) SB-122 |
| AAAG | ANTIMONY (51) SB-124 |
| AAAH | ANTIMONY (51) SB-125 |
| AAAJ | ARGON (18) AR-37 |
| AAAK | ARGON (18) AR-41 |
| AAAL | ARGON (18) AR-41, UNCOMPRESSED |
| AAAM | ARSENIC (33) AS-73 |
| AAAN | ARSENIC (33) AS-74 |
| AAAP | ARSENIC (33) AS-76 |
| AAAQ | ARSENIC (33) AS-77 |
| AAAR | ASTATINE (85) AT-211 |
| AAAS | BARIUM (56) BA-131 |
| AAAT | BARIUM (56) BA-133 |
| AAAW | BARIUM (56) BA-140 |
| AAAX | BERKELIUM (97) BK-249 |
| AAAY | BERYLLIUM (4) BE-7 |
| AAAZ | BISMUTH (83) BI-206 |
| AABA | BISMUTH (83) BI-207 |
| AABB | BISMUTH (83) BI-210 |
| AABC | BISMUTH (83) BI-212 |
| AABD | BROMINE (35) BR-82 |
| AABE | CADMIUM (48) CD-109 |
| AABG | CADMIUM (48) CD-115 |
| AABF | CADMIUM (48) CD-115M |
| AABH | CALCIUM (20) CA-45 |
| AABJ | CALCIUM (20) CA-47 |
| AABK | CALIFORNIUM /98/ CF-249 |
| AABL | CALIFORNIUM /98/ CF-250 |
| AABM | CALIFORNIUM /98/ CF-252 |
| AABN | CARBON (6) C-14 |
| AABP | CERIUM (58) CE-141 |
| AABQ | CERIUM (58) CE-143 |
| AABR | CERIUM (58) CE-144 |
| AABS | CESIUM (55) CS-131 |
| AABW | CESIUM (55) CS-134 |
| AABT | CESIUM (55) CS-134M |
| AABX | CESIUM (55) CS-135 |
| AABY | CESIUM (55) CS-136 |
| AABZ | CESIUM (55) CS-137 |
| AACA | CHLORINE (17) CL-36 |
| AACB | CHLORINE (17) CL-38 |
| AACC | CHROMIUM (24) CR-51 |
| AACD | COBALT (27) CO-56 |
| AACE | COBALT (27) CO-57 |
| AACG | COBALT (27) CO-58 |
| AACF | COBALT (27) CO-58M |
| AACH | COBALT (27) CO-60 |
| AACJ | COPPER (29) CU-64 |
| AACK | CURIUM (96) CM-242 |
| AACL | CURIUM (96) CM-243 |
| AACM | CURIUM (96) CM-244 |
| AACN | CURIUM (96) CM-245 |
| AACP | CURIUM (96) CM-246 |
| AACQ | DYSPROSIUM (66) DY-154 |
| AACR | DYSPROSIUM (66) DY-165 |
| AACS | DYSPROSIUM (66) DY-166 |
| AACT | ERBIUM (68) ER-169 |
| AACW | ERBIUM (68) ER-171 |
| AACX | EUROPIUM (63) EU-150 |
| AACZ | EUROPIUM (63) EU-152 |
| AACY | EUROPIUM (63) EU-152M |
| AADA | EUROPIUM (63) EU-154 |
| AADB | EUROPIUM (63) EU-155 |
| AADC | FLUORINE (9) F-18 |
| AADD | GADOLINIUM (64) GD-153 |
| AADE | GADOLINIUM (64) GD-159 |
| AADF | GALLIUM (31) GA-67 |
| AADG | GALLIUM (31) GA-72 |
| AADH | GERMANIUM (32) GE-71 |
| AADJ | GOLD (79) AU-193 |
| AADK | GOLD (79) AU-194 |
| AADL | GOLD (79) AU-195 |
| AADM | GOLD (79) AU-196 |
| AADN | GOLD (79) AU-198 |
| AADP | GOLD (79) AU-199 |
| AADQ | HAFNIUM (72) HF-181 |
| AADR | HOLMIUM (67) HO-166 |
| AADS | INDIUM (49) IN-113M |
| AADT | INDIUM (49) IN-114M |
| AADX | INDIUM (49) IN-115 |
| AADW | INDIUM (49) IN-115M |
| AADY | IODINE (53) I-124 |
| AADZ | IODINE (53) I-125 |
| AAEA | IODINE (53) I-126 |
| AAEB | IODINE (53) I-129 |
| AAEC | IODINE (53) I-131 |
| AAED | IODINE (53) I-132 |
| AAEE | IODINE (53) I-133 |
| AAEF | IODINE (53) I-134 |
| AAEG | IODINE (53) I-135 |
| AAEH | IRIDIUM (77) IR-190 |
| AAEJ | IRIDIUM (77) IR-192 |
| AAEK | IRIDIUM (77) IR-194 |
| AAEL | IRON (26) FE-55 |
| AAEM | IRON (26) FE-59 |
| AAEQ | KRYPTON (36) KR-85 |
| AAER | KRYPTON (36) KR-85, UNCOMPRESSED |
| AAEN | KRYPTON (36) KR-85M |
| AAEP | KRYPTON (36) KR-85M, UNCOMPRESSED |
| AAES | KRYPTON (36) KR-87 |
| AAET | KRYPTON (36) KR-87, UNCOMPRESSED |
| AAEW | LANTHANUM (57) LA-140 |
| AAEX | LEAD (82) PB-203 |
| AAEY | LEAD (82) PB-210 |
| AAEZ | LEAD (82) PB-212 |
| AAFA | LUTECIUM (71) LU-172 |
| AAFB | LUTECIUM (71) LU-177 |
| AAFC | MAGNESIUM (12) MG-28 |
| AAFD | MANGANESE (25) MN-52 |
| AAFE | MANGANESE (25) MN-54 |
| AAFF | MANGANESE (25) MN-56 |
| AAFH | MERCURY (80) HG-197 |
| AAFG | MERCURY (80) HG-197M |
| AAFJ | MERCURY (80) HG-203 |
| AAFK | MIXED FISSION PRODUCTS MF-P |
| AAFL | MOLYBDENUM (42) MO-99 |
| AAFM | NEODYMIUM (60) ND-147 |
| AAFN | NEODYMIUM (60) ND-149 |
| AAFP | NEPTUNIUM (93) NP-237 |
| AAFQ | NEPTUNIUM (93) NP-239 |
| AAFR | NICKEL (28) NI-56 |
| AAFS | NICKEL (28) NI-59 |
| AAFT | NICKEL (28) NI-63 |
| AAFW | NICKEL (28) NI-65 |
| AAFX | NIOBIUM (41) NB-93M |
| AAFY | NIOBIUM (41) NB-95 |
| AAFZ | NIOBIUM (41) NB-97 |
| AAGA | OSMIUM (76) OS-185 |
| AAGC | OSMIUM (76) OS-191 |
| AAGB | OSMIUM (76) OS-191M |
| AAGD | OSMIUM (76) OS-193 |
| AAGE | PALLADIUM (46) PD-103 |
| AAGF | PALLADIUM (46) PD-109 |
| AAGG | PHOSPHORUS (15) P-32 |
| AAGH | PLATINUM (78) PT-191 |
| AAGJ | PLATINUM (78) PT-193 |
| AAGK | PLATINUM (78) PT-193M |
| AAGM | PLATINUM (78) PT-197 |
| AAGL | PLATINUM (78) PT-197M |
| AAGN | PLUTONIUM (94) PU-238 |
| AAGP | PLUTONIUM (94) PU-239 |
| AAGQ | PLUTONIUM (94) PU-240 |
| AAGR | PLUTONIUM (94) PU-241 |
| AAGS | PLUTONIUM (94) PU-242 |
| AAGT | POLONIUM (84) PO-210 |
| AAGW | POTASSIUM (19) K-42 |
| AAGX | POTASSIUM (19) K-43 |
| AAGY | PRASEODYMIUM (59) PR-142 |
| AAGZ | PRASEODYMIUM (59) PR-143 |
| AAHA | PROMETHIUM (61) PM-147 |
| AAHB | PROMETHIUM (61) PM-149 |
| AAHC | PROTACTINIUM (91) PA-230 |
| AAHD | PROTACTINIUM (91) PA-231 |
| AAHE | PROTACTINIUM (91) PA-233 |
| AAHF | RADIUM (88) RA-223 |
| AAHG | RADIUM (88) RA-224 |
| AAHH | RADIUM (88) RA-226 |
| AAHJ | RADIUM (88) RA-228 |
| AAHK | RADON (86) RN-220 |
| AAHL | RADON (86) RN-222 |
| AAHM | RHENIUM (75) RE-183 |
| AAHN | RHENIUM (75) RE-186 |
| AAHP | RHENIUM (75) RE-187 |
| AAHQ | RHENIUM (75) RE-188 |
| AAHR | RHENIUM (75) RE-NATURAL |
| AAHS | RHODIUM (45) RH-103M |
| AAHT | RHODIUM (45) RH-105 |
| AAHW | RUBIDIUM (37) RB-86 |
| AAHX | RUBIDIUM (37) RB-87 |
| AAHY | RUBIDIUM (37) RB-NATURAL |
| AAJA | RUTHENIUM (44) RU-103 |
| AAJB | RUTHENIUM (44) RU-105 |
| AAJC | RUTHENIUM (44) RU-106 |
| AAHZ | RUTHENIUM (44) RU-97 |
| AAJD | SAMARIUM (62) SM-145 |
| AAJE | SAMARIUM (62) SM-147 |
| AAJF | SAMARIUM (62) SM-151 |
| AAJG | SAMARIUM (62) SM-153 |
| AAJH | SCANDIUM (21) SC-46 |
| AAJJ | SCANDIUM (21) SC-47 |
| AAJK | SCANDIUM (21) SC-48 |
| AAJL | SELENIUM (34) SE-75 |
| AAJM | SILICON (14) SI-31 |
| AAJN | SILVER (47) AG-105 |
| AAJP | SILVER (47) AG-110M |
| AAJQ | SILVER (47) AG-111 |
| AAJR | SODIUM (11) NA-22 |
| AAJS | SODIUM (11) NA-24 |
| AAJW | STRONTIUM (38) SR-85 |
| AAJT | STRONTIUM (38) SR-85M |
| AAJX | STRONTIUM (38) SR-89 |
| AAJY | STRONTIUM (38) SR-90 |
| AAJZ | STRONTIUM (38) SR-91 |
| AAKA | STRONTIUM (38) SR-92 |
| AAKB | SULPHUR (16) S-35 |
| AAKC | TANTALUM (73) TA-182 |
| AAKE | TECHNETIUM (43) TC-96 |
| AAKD | TECHNETIUM (43) TC-96M |
| AAKG | TECHNETIUM (43) TC-97 |
| AAKF | TECHNETIUM (43) TC-97M |
| AAKJ | TECHNETIUM (43) TC-99 |
| AAKH | TECHNETIUM (43) TC-99M |
| AAKK | TELLURIUM (52) TE-125M |
| AAKM | TELLURIUM (52) TE-127 |
| AAKL | TELLURIUM (52) TE-127M |
| AAKP | TELLURIUM (52) TE-129 |
| AAKN | TELLURIUM (52) TE-129M |
| AAKQ | TELLURIUM (52) TE-131M |
| AAKR | TELLURIUM (52) TE-132 |
| AAKS | TERBIUM (65) TB-160 |
| AAKT | THALLIUM (81) TL-200 |
| AAKW | THALLIUM (81) TL-201 |
| AAKX | THALLIUM (81) TL-202 |
| AAKY | THALLIUM (81) TL-204 |
| AAKZ | THORIUM (90) TH-227 |
| AALA | THORIUM (90) TH-228 |
| AALB | THORIUM (90) TH-230 |
| AALC | THORIUM (90) TH-231 |
| AALD | THORIUM (90) TH-232 |
| AALE | THORIUM (90) TH-234 |
| AALF | THORIUM (90) TH-NATURAL |
| AALG | THULIUM (69) TM-168 |
| AALH | THULIUM (69) TM-170 |
| AALJ | THULIUM (69) TM-171 |
| AALK | TIN (50) SN-113 |
| AALL | TIN (50) SN-117M |
| AALM | TIN (50) SN-121 |
| AALN | TIN (50) SN-125 |
| AALP | TRITIUM (1) H-3 |
| AALQ | TRITIUM (1) H-3 AS GAS, LUMINOUS PAINT, OR ADSORBED ON SOLID MATERIAL |
| AALR | TUNGSTEN (74) W-181 |
| AALS | TUNGSTEN (74) W-185 |
| AALT | TUNGSTEN (74) W-187 |
| AALW | URANIUM (92) U-230 |
| AALX | URANIUM (92) U-232 |
| AALY | URANIUM (92) U-233 |
| AALZ | URANIUM (92) U-234 |
| AAMA | URANIUM (92) U-235 |
| AAMB | URANIUM (92) U-236 |
| AAMC | URANIUM (92) U-238 |
| AAMF | URANIUM (92) U-DEPLETED |
| AAME | URANIUM (92) U-ENRICHED |
| AAMD | URANIUM (92) U-NATURAL |
| AAMG | VANADIUM (23) V-48 |
| AAMH | VANADIUM (23) V-49 |
| AAMJ | XENON (54) XE-125 |
| AAMK | XENON (54) XE-131M |
| AAML | XENON (54) XE-131M, UNCOMPRESSED |
| AAMM | XENON (54) XE-133 |
| AAMN | XENON (54) XE-133, UNCOMPRESSED |
| AAMP | XENON (54) XE-135 |
| AAMQ | XENON (54) XE-135, UNCOMPRESSED |
| AAMR | YTTERBIUM (70) YB-175 |
| AAMS | YTTRIUM (39) Y-88 |
| AAMT | YTTRIUM (39) Y-90 |
| AAMX | YTTRIUM (39) Y-91 |
| AAMW | YTTRIUM (39) Y-91M |
| AAMY | YTTRIUM (39) Y-92 |
| AAMZ | YTTRIUM (39) Y-93 |
| AANA | ZINC (30) ZN-65 |
| AANC | ZINC (30) ZN-69 |
| AANB | ZINC (30) ZN-69M |
| AAND | ZIRCONIUM (40) ZR-93 |
| AANE | ZIRCONIUM (40) ZR-95 |
| AANF | ZIRCONIUM (40) ZR-97 |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDE)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAZA000*;PRMTDIRA000$$DRHA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJIRA000R2.0*;PMWTJIRA000R2.0$$JIRA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ027*;HZRDDHAZ054$$DHAZ035*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ027 | IRIDIUM |
| HAZ054 | MERCURY |
| HAZ035 | RADIOACTIVE |
| HAZ055 | RADIUM 223 |
| HAZ056 | RADIUM 224 |
| HAZ057 | RADIUM 226 |
| HAZ058 | RADIUM 228 |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information