A log or block used as a bearing surface where natural lubrication is required, such as shaft bearings, dead eyes, and lizards.

FSC Information

5510	Lumber and Related Basic Wood Materials

Colloquial Information

No Colloquials assigned to this Approve Item Name at this time

Change List

MRC PDNB has been added

MRC ZZZP has been deleted

NAMEDITEM NAME

NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.

Enter the item name code.

(NAMED32335*)

CSTSDTYPICAL WOOD PRODUCTS USE

THE REQUIRED PURPOSE OR APPLICATION OF THE TYPICAL WOOD PRODUCTS FOR WHICH THE ITEM IS INTENDED.

Enter the applicable reply code from the table below

(CSTSDAB)

Table 1
	Reply Code (AP62)	Reply
	AB	ANTENNA STAKE
	AC	BEAMS, STINGERS, POSTS, COLUMNS AND STRUTS
	AD	BENDING OAK FOR SHIP AND BOAT CONSTRUCTION
	AE	BEVELED SIDING FOR EXTERIOR SURFACES
	AF	BLOCKING, WEDGES AND HEAVY MACHINERY PILE SUPPORTS
	AG	CLEAT STOCK FOR BOXES, FURRING STRIPS AND SUBFLOORING
	AH	COMMUNICATION AND TRANSMISSION LINES, FULL LENGTH PRESERVATIVE TREATED, GAINED AND BORED FOR TWO STANDARD CROSSARMS
	AJ	CORE MATERIAL FOR USE IN 463 L PALLETS DESIGNATED HCU-LE
	AK	CUTTING GRADE FOR REMANUFACTURING PURPOSES SUCH AS DOOR AND WINDOW STOCK, PATTERNS, FURNITURE AND TEMPLATES
	AL	CUTTING GRADES FOR REMANUFACTURE
	AM	CUTTING QUALITY FINISH GRADES USED IN LIEU OF SHOP GRADES FOR REMANUFACTURING AND FINISH PURPOSES
	AN	DAMAGE CONTROL
	AP	DECKING AND MANUFACTURE OF LAMINATED SHIP DECKING
	AQ	DECKING AND PLANKING FOR BARGES
	AR	DECKING AND PLANKING FOR SHIPS
	AS	DECKING FOR SHIP AND CARRIER MARGINS
	AT	DROP SIDING FOR EXTERIOR SURFACES
	AW	DRY DOCKS AND BLOCKING
	AX	DUNNAGE
	AZ	EXPENSIVE HIGH QUALITY FINISH LUMBER FOR INTERIOR TRIM, DOOR AND WINDOW TRIM AND CABINETS
	BA	FIRE-RETARDANT TREATED SCAFFOLD PLANK FOR BOATS AND SHIPS
	BB	FIRE-RETARDANT TREATED STRESS RATED DAMAGE CONTROL SHORING
	BG	GENERAL CONSTRUCTION, SKIDS AND HEAVY CRATING
	BH	GENERAL PURPOSE WOOD ROD USE
	BJ	GOOD QUALITY FINISH FOR CORNICE TRIM, DOOR AND WINDOW CASING AND CABINET WORK
	EX	GROUND STAKE
	BK	HARDWOOD FLOORING
	BL	HIGH QUALITY BEAMS, STRINGERS, POSTS, TIMBERS, COLUMNS AND STRUTS
	BM	HIGH QUALITY CONSTRUCTION AND INDUSTRIAL USES, HEAVY FRAMING AND DECKING
	BN	HIGH QUALITY CONSTRUCTION, SHEATHING AND BLOCKING
	BP	HIGH QUALITY FINISH INTERIOR TRIM, CABINET WORK, CASING, BASEBOARD, DOOR AND WINDOW TRIM
	BQ	HIGH QUALITY SOFTWOOD FLOORING
	BR	HIGHEST QUALITY AND MOST EXPENSIVE FINISH LUMBER FOR INTERIOR TRIM, CABINET WORK, DOOR AND WINDOW TRIM
	BS	INTERIOR AND EXTERIOR TRIM
	BT	LAMINATED OAK DECKING FOR BOATS AND SHIPS
	BW	LATH GROUND WORK FOR PLASTERING
	BX	LIGHT FRAMING FOR HIGH QUALITY CONSTRUCTION, STUDS AND ROOF TRUSSES
	BY	LIGHT WEIGHT BOX AND CRATE CONSTRUCTION
	BZ	LINE CONSTRUCTION POLES
	CA	LOW COST CONSTRUCTION, BLOCKING, BOXES, CRATES AND DUNNAGE
	CB	LOW QUALITY SHEATHING, DUNNAGE, BOXING AND CRATING
	CC	MAHOGANY PLANKING FOR BOATS AND SHIPS
	CD	ORDINARY CONSTRUCTION, BOXES, STUDS, RAFTERS AND BLOCKING
	CE	PALLETS, BLOCKING AND BRACING
	AY	PILES FOR COFFERDAMS, FALSE-WORK AND OTHER TEMPORARY CONSTRUCTION PRESERVATIVE TREATED FOR LAND OR FRESH WATER USE
	BC	PILES FOR DOCKS, WHARVES AND BUILDING FOUNDATIONS PRESERVATIVE TREATED FOR COASTAL WATERS WHERE MODERATE TO HEAVY LIMNORIA ATTACK EXPECTED AND PHOLADS ARE ABSENT
	BD	PILES FOR DOCKS, WHARVES AND BUILDING FOUNDATIONS PRESERVATIVE TREATED FOR COASTAL WATERS WHERE TEREDO PRESENT AND LIGHT LIMNORIA ACTIVITY
	BE	PILES FOR DOCKS, WHARVES AND BUILDING FOUNDATIONS PRESERVATIVE TREATED FOR COASTAL WATERS WITH DUAL TREATMENT FOR SEVERE BORER HAZARD
	BF	PILES FOR DOCKS, WHARVES AND BUILDING FOUNDATIONS PRESERVATIVE TREATED FOR LAND OR FRESH WATER USE
	CF	PORT ORFORD AND ALASKA YELLOW CEDAR PLANKING FOR BOATS AND SHIPS
	CG	PRESERVATIVE TREATED BEAMS, STRINGERS, POSTS, TIMBERS, COLUMNS AND STRUTS FOR ABOVE GROUND USE
	CH	PRESERVATIVE TREATED BEAMS, STRINGERS, POSTS, TIMBERS, COLUMNS AND STRUTS WHERE CREOSOTE OR OIL-BORNE PRESERVATIVES ARE REQUIRED FOR USE IN FRESH WATER GROUND CONTACT
	CJ	PRESERVATIVE TREATED BRACE, CORNER, GATE AND LINE FENCE POSTS
	CK	PRESERVATIVE TREATED FOR HEAVY CONSTRUCTION, RAFTERS, DECKING, BEAMS AND STRINGERS FOR ABOVE GROUND USE WHERE CLEANLINESS AND PAINTABILITY REQUIRED
	CL	PRESERVATIVE TREATED FRAMING FOR HEAVY CONSTRUCTION FOR ABOVE GROUND USE FOR CLEANLINESS AND PAINTABILITY
	CM	PRESERVATIVE TREATED HIGH QUALITY CONSTRUCTION FOR ABOVE GROUND USE FOR CLEANLINESS AND PAINTABILITY
	CN	PRESERVATIVE TREATED HIGH QUALITY CONSTRUCTION FOR ABOVE GROUND USE WHERE CLEANLINESS AND PAINTABILITY NOT REQUIRED
	DZ	PRESERVATIVE TREATED HIGH QUALITY CONSTRUCTION FOR USE IN FRESH WATER OR GROUND CONTACT
	CP	PRESERVATIVE TREATED HIGH QUALITY CONSTRUCTION WHEN CREOSOTE OR OIL-BORNE PRESERVATIVES ARE REQUIRED
	CQ	PRESERVATIVE TREATED HIGH QUALITY DROP SIDING
	CR	PRESERVATIVE TREATED HIGH QUALITY FLOORING OR EXTERIOR DECKING
	CS	PRESERVATIVE TREATED OAK PLANKING FOR SHIPS
	CT	PRESERVATIVE TREATED SHEATHING, CONCRETE FORMS, SUBFLOORING, BLOCKING AND CRATES FOR CLEANLINESS AND PAINTABILITY
	CW	PRESERVATIVE TREATED STRESS RATED JOISTS AND PLANKS FOR USE IN CRIBBING FOR BAILEY TYPE BRIDGES
	CX	PROPELLER SHAFT BEARINGS
	CY	RAILROAD CROSSTIES
	CZ	RAILWAY TURNOUT SWITCHTIES
	DA	RED CEDAR POLES FOR COMMUNICATION AND TRANSMISSION LINES, BUTT TREATED
	DB	ROOF AND WALL SHEATHING, SUBFLOORING, BOXES, CRATES AND PALLETS
	DC	SCAFFOLD PLANK FOR BOATS AND SHIPS
	DD	SEA RESCUE EQUIPMENT
	DE	SHEATHING AND SUBFLOORING
	DF	SHEATHING, SUBFLOORING, BOXES AND CRATES
	DG	STAIR STEPS
	DH	STRUCTURAL JOISTS AND PLANKS FOR HIGH QUALITY CONSTRUCTION RAFTERS, DECKING, STRINGERS AND HEAVY CRATING
	DJ	STRUCTURAL LIGHT FRAMING, JOISTS AND PLANKS FOR HIGHEST QUALITY CONSTRUCTION
	DK	STUD USE INCLUDING USE IN LOAD BEARING WALLS
	DL	SUBFLOORING, DECKING AND HEAVY SHEATHING
	DM	TANK AND BOAT CONSTRUCTION
	DN	TEMPLATES AND PATTERNS
	DP	TEMPORARY CONSTRUCTION, LOW GRADE BRACING, CRATING AND DUNNAGE
	DQ	TEMPORARY SHEATHING, DUNNAGE, BOXING AND CRATING
	DR	TIE SET AND RAILWAY TURNOUT SWITCHTIES
	DS	VEHICLE LUMBER FOR CONSTRUCTION AND REPAIR OF VEHICLE BODIES
	DT	VERY HIGH QUALITY AND VERY EXPENSIVE FINISH LUMBER WHERE HIGH APPEARANCE REQUIRED IN CONJUNCTION WITH STRUCTURAL REQUIREMENTS
	DW	WEDGES AND GENERAL CONSTRUCTION

CQWYHSPECIES-GRADE AND GRADING ASSOCIATION

AN INDICATION OF THE SPECIES AND GRADE OF THE ITEM,AND THE GRADING ASSOCIATION.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below.

(CQWYHBJBZAH2.0*;CQWYHBJBZAH2.0$HBJBZAH2.0*;CQWYHBJBZAH2.0$$HBJBZAH2.1*)

Table 1
	Reply Code (AM00)	Reply
	DM	ALDER
	DN	ALDER, RED
	AA	ANY ACCEPTABLE
	AB	ASH
	DP	ASH, BLACK
	DD	ASH, WHITE
	DR	ASPEN
	AS	BALSA
	AT	BASSWOOD
	DS	BASSWOOD, AMERICAN
	AW	BEECH
	DT	BEECH, AMERICAN
	AX	BIRCH
	DW	BIRCH, SWEET
	DX	BIRCH, YELLOW
	DY	BOXELDER
	DZ	BUCKEYE
	EA	BUTTERNUT
	AH	CEDAR
	FR	CEDAR, ALASKA
	EC	CEDAR, ATLANTIC WHITE
	ED	CEDAR, EASTERN RED
	ET	CEDAR, INCENSE
	EE	CEDAR, NORTHERN WHITE
	FS	CEDAR, PORT ORFORD
	EB	CEDAR, WESTERN
	AN	CEDAR, WESTERN RED
	BB	CHERRY
	EF	CHERRY, BLACK
	BC	CHESTNUT
	HN	COACHWOOD
	EG	COTTONWOOD
	AJ	CYPRESS
	AD	DOUGLAS FIR
	HK	DOUGLAS-FIR, COASTAL
	HL	DOUGLAS-FIR, SOUTH, INTERIOR
	BF	ELM
	EH	ELM, AMERICAN
	EJ	ELM, ROCK
	AE	FIR
	EK	FIR, BALSAM
	EL	FIR, GRAND
	EM	FIR, SUBALPINE
	BH	GUM
	EN	GUM, BLACK
	CW	GUM, SWEET
	EQ	HACKBERRY
	CC	HARDWOOD
	FW	HEM-FIR
	BJ	HEMLOCK
	ER	HEMLOCK, EASTERN
	ES	HEMLOCK, MOUNTAIN
	DA	HEMLOCK, WESTERN
	AC	HICKORY
	EW	HOLLY
	BN	LARCH
	EX	LAUAN
	EY	LIGNUM VITAE
	BP	LOCUST
	AY	LOCUST, BLACK
	FA	LOCUST, HONEY
	DQ	MAGNOLIA
	BS	MAHOGANY
	HQ	MAHOGANY, GABOON
	BT	MAPLE
	EZ	MAPLE, BLACK
	EP	MAPLE, HARD
	FB	MAPLE, RED
	FC	MAPLE, SILVER
	FD	MAPLE, SOFT
	FE	MAPLE, SUGAR
	AF	OAK
	CK	OAK, RED
	DG	OAK, WHITE
	FF	PECAN
	AK	PINE
	BE	PINE, EASTERN WHITE
	HP	PINE, HOOP
	BL	PINE, IDAHO WHITE
	BM	PINE, JACK
	BQ	PINE, LODGEPOLE
	FJ	PINE, NORWAY
	FG	PINE, PITCH
	CB	PINE, PONDEROSA
	CQ	PINE, SOUTHERN
	CT	PINE, SUGAR
	CD	POPLAR
	DK	POPLAR, YELLOW
	AL	REDWOOD
	HS	SAPELLI
	HR	SIPO
	DL	SOFTWOOD
	CS	SPRUCE
	FK	SPRUCE, EASTERN
	BG	SPRUCE, ENGELMANN
	CN	SPRUCE, SITKA
	FL	SPRUCE, WESTERN WHITE
	FX	SPRUCE-PINE-FIR
	FM	SYCAMORE, AMERICAN
	FN	TAMARACK
	FH	TUPELO
	AG	WALNUT
	AZ	WALNUT, BLACK
	FP	WILLOW
	FQ	WILLOW, BLACK

Table 2
	Reply Code (AP02)	Reply
	KT	0A
	KU	0B
	AB	1 AND 2 CLEAR
	AC	1 COMMON
	AS	2 COMMON
	KV	3 A
	KW	3 B
	BH	3 COMMON
	BJ	3A COMMON
	BK	3B COMMON
	BR	4 COMMON
	BS	5 COMMON
	BW	A
	BX	A BEVEL SIDING
	KK	A CEE
	BY	A FINISH
	BZ	APPEARANCE
	CA	B
	CB	B AND BETTER
	CC	B AND BETTER DROP SIDING
	CD	B AND BETTER FINISH
	CE	B AND BETTER FLOORING
	CF	B AND BETTER INDUSTRIAL CLEARS
	CG	B BEVEL SIDING
	KL	B CEE
	CH	B FINISH
	CJ	BARGE FRAMING
	CK	BARGE PLANKING AND DECKING
	CL	C
	CM	C AND BETTER
	CP	C AND BETTER FINISH
	CN	C AND BETTER FLOORING
	CQ	C AND BETTER INDUSTRIAL CLEARS
	CR	C AND BETTER SELECT
	JQ	C AND BETTER SIDING
	CS	C AND BETTER V.G. STEPPING
	KM	C CEE
	CT	C DROP SIDING
	CW	C FINISH
	CX	C FLOORING
	CY	C INDUSTRIAL
	CZ	C SELECT
	DA	C SHIP DECKING
	JR	C STEPPING
	KN	CABINET WORK
	KQ	CARPENTER
	DB	CHOICE
	DC	CLEAR
	DD	CLEAR ALL HEART
	DE	CLEAR ALL HEART SIDING
	DF	CLEAR HEART
	DG	CLEAR HEART STRUCTURAL
	DH	CLEAR SIDING
	DJ	CLEAR STRUCTURAL
	DK	CLEAR V.G. HEART BEVEL SIDING
	DL	COLONIAL
	DM	COMMERCIAL DECKING
	JS	COMMON DIMENSION
	DN	CONSTRUCTION
	DP	CONSTRUCTION COMMON
	DQ	CONSTRUCTION HEART
	DR	D
	DS	D DROP SIDING
	DT	D FINISH
	DW	D FLOORING
	DX	D INDUSTRIAL CLEARS
	DY	D SELECT
	DZ	D V.G. STEPPING
	EA	DENSE INDUSTRIAL 65 SCAFFOLD PLANK
	EB	DENSE INDUSTRIAL 72 SCAFFOLD PLANK
	JT	DENSE PREMIUM SCAFFOLD PLANK
	JW	DENSE SELECT STRUCTURAL
	EC	DENSE STRUCTURAL 65
	ED	DENSE STRUCTURAL 72
	KJ	DENSE STRUCTURAL 86
	EF	E
	EG	ECONOMY
	KR	EXCEPTIONAL CHOISE
	EH	FACTORY SELECT
	EJ	FINISH
	EK	FIRST
	EL	FIRSTS
	EM	FOUNDATION
	KS	FOURTH
	JZ	GRADE B
	KA	GRADE C
	JX	GRADE I
	JY	GRADE II
	ET	INDUSTRIAL
	EW	INDUSTRIAL 65
	EX	INDUSTRIAL 72
	EY	INDUSTRIAL 86
	EZ	INDUSTRIAL CLEAR ALL HEART
	FA	INDUSTRIAL FACTORY SELECT
	KP	JOINERY
	FD	KNOTTY
	FE	LATH
	FF	MARGIN PLANK
	FG	MERCHANTABLE
	FH	MOULDINGS
	AD	NO. 1
	AE	NO. 1 BOARDS
	AF	NO. 1 CONSTRUCTION BOARDS
	AG	NO. 1 CUTS
	JM	NO. 1 DENSE SR
	AH	NO. 1 DROP SIDING
	AJ	NO. 1 FACTORY
	AK	NO. 1 LATH
	AM	NO. 1 SHOP
	AN	NO. 1 SR TIMBERS
	AP	NO. 1 STADIUM GRADE
	AQ	NO. 1 STRUCTURAL
	AR	NO. 1 TIMBERS
	AT	NO. 2
	AW	NO. 2 BOARDS
	AX	NO. 2 CONSTRUCTION BOARDS
	JN	NO. 2 DIMENSION
	AY	NO. 2 DROP SIDING
	AZ	NO. 2 FLOORING
	BA	NO. 2 FOUNDATION GRADE
	AL	NO. 2 LATH
	BB	NO. 2 SHOP
	BC	NO. 2 SR TIMBERS
	BD	NO. 2 STRUCTURAL
	BE	NO. 2 TIMBERS
	BL	NO. 3
	BM	NO. 3 BOARDS
	BN	NO. 3 CONSTRUCTION BOARDS
	BP	NO. 3 SHOP
	BQ	NO. 3 TIMBERS
	JP	NO. 4 BOARDS
	FJ	PREMIUM
	FK	PREMIUM SCAFFOLD PLANK
	FL	PRIME FINISH
	FM	QUALITY
	FN	SCAFFOLD NO. 1
	FP	SCAFFOLD NO. 2
	FQ	SECOND
	KB	SECOND AND BETTER
	FR	SECONDS
	FS	SELECT
	KC	SELECT CAR STOCK
	FT	SELECT DECKING
	FW	SELECT HEART
	FX	SELECT MERCHANTABLE
	FY	SELECT SHOP
	FZ	SELECT STRUCTURAL
	GA	SELECT STRUCTURAL SCAFFOLD PLANK
	GB	SELECTED DECKING
	BF	SELECTED NO. 2 COMMON
	BG	SELECTED NO. 3 COMMON
	GC	SELECTS
	GD	SHEATHING
	GE	SHIP DECKING
	GF	SHIP PLANKING
	KD	SOUND SQUARE EDGE
	GG	SOUND WORMY
	GJ	STADIUM PLANK SEATS
	GK	STADIUM PLANK WALK BOARDS
	GH	STADIUM PLANKS
	GL	STADIUM SEAT STOCK
	GM	STANDARD
	KE	STANDARD MOULDINGS
	GN	STERLING
	GP	STUD
	GQ	SUPERIOR
	KF	SUPERIOR FINISH
	GR	SUPREME
	GS	TANK
	GT	TANK STOCK
	GW	TANK STOCK 2 IN. TO 3 IN.
	GX	TANK STOCK 4 IN. AND THICKER
	HA	TANK STOCK UNDER 4 IN.
	GY	THIRD
	GZ	TRUSS
	KG	UNGRADED
	HB	UTILITY
	KH	VEHICLE NUMBER

Table 3
	Reply Code (AP03)	Reply
	AT	ASSOCIATION FRANCAISE DE NORMALISATION
	AC	MAPLE FLOORING MANUFACTURERS ASSOCIATION
	AD	NATIONAL HARDWOOD LUMBER ASSOCIATION
	AR	NATIONAL LUMBER GRADES AUTHORITY, CANADA
	AF	NATIONAL OAK FLOORING MANUFACTURERS ASSOCIATION
	AG	NORTHEASTERN LUMBER MANUFACTURERS ASSOCIATION
	AH	NORTHERN HARDWOOD AND PINE MANUFACTURERS ASSOCIATION
	AJ	REDWOOD INSPECTION SERVICE
	AL	SOUTHERN PINE INSPECTION BUREAU
	AS	UNRECOGNIZED
	AM	WEST COAST LUMBER INSPECTION BUREAU
	AB	WESTERN WOOD PRODUCTS ASSOCIATION

IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CSHP, YOU MUST ANSWER MRC (CSHB)

CSHP*JTHICKNESS-LOCATION AND MEASURING METHOD

A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED.

Enter the applicable Reply Code from Tables 1 & 2 & 3 & 4 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CSHPJACTEDSD2.0*;CSHPJACTEDSD2.0$$JACTEDSD2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AN73)	Reply
	BED	BUTT END
	AAD	OVERALL
	TED	TAPERED END

Table 4
	Reply Code (AN68)	Reply
	RN	RANDOM
	SD	SPECIFIED

CSHB*GRANDOM THICKNESS

A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.

Enter clear text.

(CSHBGCLEARTEXT)

IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CRPW, YOU MUST ANSWER MRC (CQKJ)

CRPW*JWIDTH-LOCATION AND MEASURING METHOD

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED. PLEASE USE MRC CRXX WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable Reply Code from Tables 1 & 2 & 3 & 4 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CRPWJACBEDRN2.0*;CRPWJACBEDRN2.0$$JACBEDRN2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AN73)	Reply
	BED	BUTT END
	AAD	OVERALL
	TED	TAPERED END

Table 4
	Reply Code (AN68)	Reply
	RN	RANDOM
	SD	SPECIFIED

CQKJ*GRANDOM WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter clear text.

(CQKJGCLEARTEXT)

IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CRXX, YOU MUST ANSWER MRC (CRJD)

CRXXJMEASURING METHOD AND LENGTH

THE MEANS USED AND THE MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CRXXJAASD2.0*;CRXXJAASD2.0$$JAASD2.1*)

Table 1
	Reply Code (AA05)	Reply
	F	FEET
	A	INCHES
	M	METERS
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AN68)	Reply
	RN	RANDOM
	SD	SPECIFIED

CRJD*GRANDOM LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.

Enter clear text.

(CRJDGCLEARTEXT)

CQHF*DMAXIMUM GRAIN SLOPE

INDICATES THE MAXMIUM SLOPE OF GRAIN IN RELATION TO THE LENGTH OF THE ITEM.

Enter the applicable reply code from the table below

(CQHFDAF)

Table 1
	Reply Code (AP05)	Reply
	AH	1 IN 10
	AJ	1 IN 11
	AK	1 IN 12
	AL	1 IN 13
	AM	1 IN 14
	AN	1 IN 15
	AP	1 IN 16
	AQ	1 IN 17
	AR	1 IN 18
	AS	1 IN 19
	AT	1 IN 20
	AW	1 IN 21
	AX	1 IN 22
	AY	1 IN 23
	AZ	1 IN 24
	BA	1 IN 25
	BB	1 IN 26
	BC	1 IN 27
	BD	1 IN 28
	BE	1 IN 29
	BF	1 IN 30
	AB	1 IN 4
	AC	1 IN 5
	AD	1 IN 6
	AE	1 IN 7
	AF	1 IN 8
	AG	1 IN 9

IF STYLE/REPLY CODE(s) EQ WERE ENTERED FOR MRC BMKY, YOU MUST ANSWER MRC (CQMP)

IF STYLE/REPLY CODE(s) ER OR HD WERE ENTERED FOR MRC BMKY, YOU MUST ANSWER MRC (CQMP and CSTZ)

BMKY*DTREATMENT TYPE

INDICATES THE TYPE OF TREATMENT PROVIDED.

Enter the applicable reply code from the table below

(BMKYDDF)

Table 1
	Reply Code (AK89)	Reply
	DB	FIRE RETARDANT
	EN	FIRE RETARDANT, MIL-L-19140
	HF	FUNGICIDAL
	HG	INSERT REPELLANT
	DF	MARINE BORER RESISTANT
	EQ	PRESERVATIVE, MIL-C-12436
	EP	PRESERVATIVE, MIL-P-19550
	ER	PRESERVATIVE, TT-W-571
	HD	PRESERVATIVE, TT-W-572
	DQ	WATER REPELLENT

CQMP*DPRESERVATIVE SOLUTION TYPE

INDICATES THE TYPE OF SOLUTION USED TO PRESERVE THE ITEM.

Enter the applicable reply code from the table below

(CQMPDHB*;CQMPDGS$DEZ*)

Table 1
	Reply Code (AK89)	Reply
	EY	ACID COPPER CHROMATE
	EZ	AMMONIACAL COPPER ARSENITE
	GS	CHROMATED COPPER ARSENATE, TYPE I, II OR III
	FD	CHROMATED ZINC CHLORIDE
	CM	COAL-TAR CREOSOTE
	HA	COPPER NAPHTHENATE
	HB	COPPER NAPHTHENATE HIGH CONCENTRATION
	GZ	COPPER-8-QUINOLINOLATE
	CS	CREOSOTE COAL-TAR SOLUTION
	CX	CREOSOTE PETROLEUM SOLUTION
	HC	CREOSOTE/PENTACHLOROPHENOL
	GT	DUAL TREATMENT
	GW	FLUOR-CHROME-ARSENATE-PHENOL, TYPE I OR TYPE II
	DH	PENTACHLOROPHENOL
	FH	PENTACHLOROPHENOL IN HEAVY PETROLEUM SOLVENT
	FJ	PENTACHLOROPHENOL IN LIGHT PETROLEUM SOLVENT
	GX	PENTACHLOROPHENOL IN VOLATILE SOLVENT
	GY	TRIBUTYLTIN OXIDE

CSTZ*DSERVICE USAGE

THE APPLICATION FOR WHICH THE ITEM IS INTENDED.

Enter the applicable reply code from the table below

(CSTZDAL*;CSTZDAQ$DAR*;CSTZDAQ$$DAR*)

Table 1
	Reply Code (AN66)	Reply
	AB	BUILDING
	AQ	BUILDING FOUNDATION
	AC	CONTACT W/GROUND
	AD	FENCE
	BB	FOR USE ABOVE GROUND
	BA	IMPORTANT STRUCTURAL MEMBERS IN CONTACT WITH GROUND OR FRESH WATER
	AE	IMPORTANT STRUCTURAL MEMBERS NOT IN CONTACT W/GROUND OR WATER
	AF	IN COASTAL WATERS
	AR	IN CONTACT WITH OR CLOSE PROXIMITY TO FOODSTUFF
	AG	IN FRESH WATER
	AS	LUMBER
	AT	PILES
	AW	POLES
	AX	POSTS
	AY	READY-TO-USE SOLUTIONS BY SIMPLE NONPRESSURE METHODS
	AL	TIES
	AZ	TIMBERS
	AN	UTILITY

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

CBME*JCUBIC MEASURE

A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CBMEJCF2.0*)

Table 1
	Reply Code (AN76)	Reply
	CF	CUBIC FEET
	CM	CUBIC METERS

BBRG*DSTORAGE TYPE

INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.

Enter the applicable reply code from the table below

(BBRGDAD*;BBRGDAH$DAC*)

Table 1
	Reply Code (AM81)	Reply
	AC	CLOSED SHED
	AD	CONTROLLED HUMIDITY WAREHOUSE
	AM	DEHUMIDIFIED WAREHOUSE
	AE	GENERAL PURPOSE WAREHOUSE
	AN	HEATED WAREHOUSE
	AH	OPEN SHED
	BD	OPEN STORAGE
	AJ	UNHEATED WAREHOUSE

BBRH*JINSPECTION FREQUENCY

THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.

(BBRHJDYAB2*;BBRHJDYAB2$$JDYAB3*)

Table 1
	Reply Code (AH68)	Reply
	DY	DAYS
	MH	MONTHS

Table 2
	Reply Code (AM82)	Reply
	AB	FIRST INSPECTION
	AC	REINSPECTION

AFJQ*JSTORAGE TEMP RANGE

THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.

(AFJQJFM32.0/P50.0*)

Table 1
	Reply Code (AB36)	Reply
	C	CELSIUS
	F	FAHRENHEIT

CQCT*DPRIMARY CONTAINER TYPE

INDICATES THE TYPE OF CONTAINER/S/ OR SUPPORTING DEVICE/S/ WHICH IS IN DIRECT CONTACT WITH THE ITEM.

Enter the applicable reply code from the table below

(CQCTDA)

Table 1
	Reply Code (AN65)	Reply
	A	ANY ACCEPTABLE
	ACD	BOX
	AFA	CRATE
	AFB	SKID

CRLK*JPRIMARY CONTAINER CONTENT QUANTITY

A NUMERIC VALUE OF THE VOLUME,FORM,OR DOSAGE WITHIN EACH PRIMARY CONTAINER.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CRLKJSH2.0*)

Table 1
	Reply Code (AN64)	Reply
	EA	EACH
	SH	SHEET

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

This MRC replaced MRC ZZZP

The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.

PDNB*APURCHASE DESCRIPTION IDENTIFICATION

THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.

Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.

(ZZZPJ81A37-30624A*)

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

ABMZ*JDIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABMZ3AEEJLC2.0*;ABMZ3AEEJLC2.0$JLC2.0*;ABMZ3AEEJLC2.0$$JLC2.1*)

Table 1
	ISAC Field Indicator (5000)	Location
	3ABK	TOP
	3AEE	OVERALL
	3ALJ	BOTTOM
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (AA05)	Reply
	L	MILLIMETERS
	B	MILS

Table 3
	Reply Code (AC20)	Reply
	C	MAXIMUM

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)