A cylinder with component parts designed as a reservoir to maintain a constant fluid pressure and volume in the recoil cylinder of a gun. Excludes:CYLINDER (1), HYDRAULIC ACCUMULATOR and CYLINDER ASSEMBLY, ACTUATING, LINEAR.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED31630*)
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAA2.0*;ADAVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ATEMJEXTENDED LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IT IS IN AN EXTENDED POSITION,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ATEMJAC2.0*;ATEMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMQZJCOMPRESSED LENGTH
A MEASUREMENT OF THE SMALLEST LENGTH TO WHICH THE ITEM MAY BE COMPRESSED,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMQZJAA2.0*;AMQZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAA2.0*;ADARJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXVJBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAA2.0*;ABXVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CKSFLFIRST PISTON ROD END STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST PISTON ROD END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CKSFL10*;CKSFL7$L5*;CKSFL7$$L5*)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1740 | 1 | RING TYPE |
| AAQ1749 | 10 | SLOTTED |
| AAQ1741 | 2 | BUSHING TYPE |
| AAQ1742 | 3 | BEARING TYPE |
| AAQ1743 | 4 | FORK TYPE (CLEVIS) |
| AAQ1744 | 5 | SLOT TYPE |
| AAQ1745 | 6 | TONGUE TYPE |
| AAQ1746 | 7 | EXTERNAL THREADED |
| AAQ1747 | 8 | INTERNAL THREADED |
| AAQ1748 | 9 | SPHERICAL |
CKSLDFIRST PISTON ROD END THREAD DIRECTION
THE DIRECTION OF THE FIRST PISTON ROD END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CKSL2DADAAG)
| Table 1 |
| ISAC Field Indicator (0231) | Location |
| 2DA | ALL WORKING ENDS |
| 2DB | SMALLEST WORKING END |
| 2DC | LARGEST WORKING END |
| Table 2 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC CLLP, YOU MUST ANSWER MRC (CLLQ)
CLLP*DPISTON ROD END SIMILARITY
AN INDICATION OF THE SIMILARITY OF THE PISTON ROD ENDS.
Enter the applicable reply code from the table below
(CLLPDC)
| Table 1 |
| Reply Code (AA37) | Reply |
| C | IDENTICAL |
| B | NOT IDENTICAL |
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC CLLQ, YOU MUST ANSWER MRC (CLLR)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC CLLQ, YOU MUST ANSWER MRC (CLLR)
CLLQ*LSECOND PISTON ROD END STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND PISTON ROD END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CLLQL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1740 | 1 | RING TYPE |
| AAQ1749 | 10 | SLOTTED |
| AAQ1741 | 2 | BUSHING TYPE |
| AAQ1742 | 3 | BEARING TYPE |
| AAQ1743 | 4 | FORK TYPE (CLEVIS) |
| AAQ1744 | 5 | SLOT TYPE |
| AAQ1745 | 6 | TONGUE TYPE |
| AAQ1746 | 7 | EXTERNAL THREADED |
| AAQ1747 | 8 | INTERNAL THREADED |
| AAQ1748 | 9 | SPHERICAL |
IF STYLE/REPLY CODE(s) NC, NE, NF, NJ, NS, JC, JE, JF OR UN WERE ENTERED FOR MRC CLLR, YOU MUST ANSWER MRC (CLLS and CLLT and CLLW and CLLX)
IF STYLE/REPLY CODE(s) BF OR BW WERE ENTERED FOR MRC CLLR, YOU MUST ANSWER MRC (CLLS and CLLX)
IF STYLE/REPLY CODE(s) SJ, SK, SM OR SS WERE ENTERED FOR MRC CLLR, YOU MUST ANSWER MRC (CLLS and CLLX)
IF STYLE/REPLY CODE(s) BR, BS, NH, NP, NT, PE, PF, PM, PP, PS, PT, SC, SF, SH, SL, SP, AN OR FP WERE ENTERED FOR MRC CLLR, YOU MUST ANSWER MRC (CLLX and CLLY)
CLLR*DSECOND PISTON ROD END THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE SECOND PISTON ROD END.
Enter the applicable reply code from the table below
(CLLRDPF)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| NS | UNS |
CLLS*JSECOND PISTON ROD END THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND PISTON ROD END AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLLSJAC2.0*;CLLSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLLT*ASECOND PISTON ROD END THREAD QUANTITY PER INCH
THE NUMBER OF SCREW THREADS ON THE SECOND PISTON ROD END PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CLLTAC3)
CLLW*ASECOND PISTON ROD END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD ON THE SECOND PISTON ROD END.
Enter the alpha-numeric reply with a minimum of one character.
(CLLWAB3)
CLLX*DSECOND PISTON ROD END THREAD DIRECTION
THE DIRECTION OF THE SECOND PISTON ROD END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CLLXDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CLLY*JSECOND PISTON ROD END NOMINAL PIPE THREAD SIZE
THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE SECOND PISTON ROD END PIPE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLLYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
BYXG*JSTRAIGHT BORE INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYXGJAB2.0*;BYXGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLML*HMOUNTING TYPE AND LOCATION
INDICATES THE TYPE OF MOUNTING AND THE LOCATION ON THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CLMLHACREAT2.0*;CLMLHACREAT2.0$HACREAT2.0*;CLMLHACREAT2.0$$HACREAT2.1*)
| Table 1 |
| Reply Code (AM39) | Reply |
| BFA | BALL SOCKET |
| BNA | BALL STUD |
| BNB | BEARING |
| BXR | BORE |
| ADN | BOSS |
| ACR | FLANGE |
| BPL | FLAT |
| BKK | FORK |
| ABN | LUG |
| AHT | RING |
| ABT | ROD |
| ABW | SCREW |
| AAE | STUD |
| BKL | TONGUE |
| AKG | TRUNNION |
| Table 2 |
| Reply Code (AJ91) | Reply |
| AHH | BOTH ENDS |
| DAC | CENTER SECTION |
| EAT | CYLINDER BASE |
| DAA | CYLINDER HEAD END |
| DAB | PISTON ROD END |
IF STYLE/REPLY CODE(s) EE WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (CLMQ and ABKP)
IF STYLE/REPLY CODE(s) EF WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and ABGC and ABGD)
IF STYLE/REPLY CODE(s) AL WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CDTD)
IF STYLE/REPLY CODE(s) AQ OR HP WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CDTD and ABKP)
IF STYLE/REPLY CODE(s) AT WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CLMQ)
ABDR*DMOUNTING PROVISION
THE PROVISION/S/ FOR MOUNTING THE ITEM. PLEASE USE MRC BHMS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ABDRDEE*;ABDRDAQ$$DHP*)
| Table 1 |
| Reply Code (AB21) | Reply |
| HN | LINK |
| GA | LUGS |
| EE | PIN |
| EF | SLOT |
| AL | THREADED MOUNTING HOLES |
| HP | THREADED MOUNTING SCREWS |
| AQ | THREADED MOUNTING STUDS |
| AT | UNTHREADED MOUNTING HOLES |
IF STYLE/REPLY CODE(s) 10, 11 OR 12 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (CLMR)
IF STYLE/REPLY CODE(s) 13, 14 OR 15 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDT and AFDS and AFDV)
IF STYLE/REPLY CODE(s) 16, 17, 18, 19, 20 OR 21 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDV and AFDS)
IF STYLE/REPLY CODE(s) 22, 23 OR 24 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDV and AFDW and AFDS)
IF STYLE/REPLY CODE(s) 25, 26, 27, 28, 29, 30, 31, 32 OR 33 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AZCR)
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5, 6, 7, 8 OR 9 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (CLMR)
BBBW*LMOUNTING PROVISION ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE MOUNTING PROVISION(S).
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BBBWL27)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR00107 | 1 | TWO HOLE |
| DR00127 | 10 | FIVE HOLE |
| DR00128 | 11 | FIVE STUD |
| DR00129 | 12 | FIVE SLOT |
| DR00130 | 13 | THREE HOLE TRIANGULAR |
| DR00131 | 14 | THREE STUD TRIANGULAR |
| DR00132 | 15 | THREE SLOT TRIANGULAR |
| DR00133 | 16 | FOUR HOLE SQUARE |
| DR00134 | 17 | FOUR STUD SQUARE |
| DR00135 | 18 | FOUR SLOT SQUARE |
| DR00172 | 19 | FOUR HOLE RECTANGULAR |
| DR00108 | 2 | TWO STUD |
| DR00173 | 20 | FOUR STUD RECTANGULAR |
| DR00174 | 21 | FOUR SLOT RECTANGULAR |
| DR00196 | 22 | SIX HOLE RECTANGULAR |
| DR00197 | 23 | SIX STUD RECTANGULAR |
| DR00198 | 24 | SIX SLOT RECTANGULAR |
| DR00199 | 25 | THREE HOLE BOLT CIRCLE |
| DR00200 | 26 | THREE STUD BOLT CIRCLE |
| DR00201 | 27 | THREE SLOT BOLT CIRCLE |
| DR00207 | 28 | FOUR HOLE BOLT CIRCLE |
| DR00208 | 29 | FOUR STUD BOLT CIRCLE |
| DR00109 | 3 | TWO SLOT |
| DR00209 | 30 | FOUR SLOT BOLT CIRCLE |
| DR00210 | 31 | SIX HOLE BOLT CIRCLE |
| DR00211 | 32 | SIX STUD BOLT CIRCLE |
| DR00212 | 33 | SIX SLOT BOLT CIRCLE |
| DR00213 | 34 | SINGLE HOLE |
| DR00214 | 35 | SINGLE STUD |
| DR00215 | 36 | SINGLE SLOT |
| DR00112 | 4 | THREE HOLE |
| DR00117 | 5 | THREE STUD |
| DR00118 | 6 | THREE SLOT |
| DR00124 | 7 | FOUR HOLE |
| DR00125 | 8 | FOUR STUD |
| DR00126 | 9 | FOUR SLOT |
AFDS*JLONGEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDSJAB2.0*;AFDSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDT*JSHORTEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDTJAC2.0*;AFDTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDV*JLONGEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDVJAB2.0*;AFDVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDW*JSHORTEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDWJAA2.0*;AFDWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZCR*JMOUNTING FACILITY CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AZCRJAC2.0*;AZCRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLMR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING PROVISIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMRJAA2.0*;CLMRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) NC, NE, NF, NJ, NS, JC, JE, JF OR UN WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CDTF and CDTG and AKBM and AKBN and CLMN)
IF STYLE/REPLY CODE(s) BF OR BW WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CDTF and AKBN and CLMN)
IF STYLE/REPLY CODE(s) BR, BS, NH, NP, NT, PE, PF, PM, PP, PS, PT, SC, SF, SH, SL, SP, AN OR FP WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (AKBN and CLMP)
IF STYLE/REPLY CODE(s) SJ, SK, SM OR SS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CTXF and CDTF and AKBN and CLMN)
CDTD*DMOUNTING FACILITY THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A MOUNTING FACILITY DIAMETER.
Enter the applicable reply code from the table below
(CDTDDSF*;CDTDDNF$$DSP*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| NS | UNS |
CDTF*JMOUNTING FACILITY THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CDTFJAA2.0*;CDTFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CDTG*AMOUNTING FACILITY THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE MOUNTING FACILITY PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CDTGAB3)
CTXF*BMOUNTING FACILITY THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE MOUNTING FACILITY,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXFB2.0)
AKBM*AMOUNTING FACILITY THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED MOUNTING FACILITY.
Enter the alpha-numeric reply with a minimum of one character.
(AKBMAC8)
AKBN*DMOUNTING FACILITY THREAD DIRECTION
THE DIRECTION OF THE THREADS OF A MOUNTING FACILITY WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AKBNDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CLMN*JMOUNTING FACILITY THREAD LENGTH
THE LENGTH OF THE THREADED PORTION OF THE MOUNTING FACILITY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMNJAC2.0*;CLMNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLMP*JMOUNTING FACILITY NOMINAL PIPE THREAD SIZE
THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE MOUNTING FACILITY PIPE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMPJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CLMQ*JMOUNTING FACILITY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMQJAC2.0*;CLMQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKP*JMOUNTING FACILITY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FACILITY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKPJAA2.0*;ABKPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAC2.0*;ABGCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGD*JSLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGDJAA2.0*;ABGDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) DAA, DAB OR DAC WERE ENTERED FOR MRC CLMS, YOU MUST ANSWER MRC (CLMT)
CLMS*JPORT LOCATION AND QUANTITY
INDICATES THE LOCATION AND NUMBER OF PORTS ON THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CLMSJDAC2*;CLMSJDAC2$$JDAC3*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| DAC | CENTER SECTION |
| EAT | CYLINDER BASE |
| DAA | CYLINDER HEAD END |
| DAB | PISTON ROD END |
IF STYLE/REPLY CODE(s) 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42 OR 43 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (AARX)
CLMT*LPORT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PORT.
Enter the applicable ISAC from the table below folowed by the mode code and the applicable reply code from the drawing group below.
(CLMT3AGRL31*;CLMT3AGRL31$L17*;CLMT3AGRL31$$L17*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1762 | 1 | SWIVEL NUT, FLARE |
| AAQ1771 | 10 | SWIVEL NUT, GAS |
| AAQ1772 | 11 | DOUBLE COMPRESSION |
| AAQ1773 | 12 | HIGH PRESSURE FLARE |
| AAQ1774 | 13 | GASKET SEAL COMPRESSION |
| AAQ1775 | 14 | INVERTED FLARE |
| AAQ1776 | 15 | FLARED |
| AAQ1777 | 16 | FLARED |
| AAQ1778 | 17 | COMPRESSION |
| DQ00439 | 18 | FLARELESS |
| AAQ1780 | 19 | PLAIN |
| AAQ1763 | 2 | SWIVEL NUT, INVERTED FLARE |
| AAQ1781 | 20 | SWIVEL NUT INVERTED FLARE |
| AAQ1782 | 21 | SWIVEL, PLAIN |
| AAQ1783 | 22 | GASKET SEAL |
| AAQ1784 | 23 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1785 | 24 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1786 | 25 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1787 | 26 | SWIVEL NUT, FLARED |
| AAQ1788 | 27 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAQ1789 | 28 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAQ1790 | 29 | SOCKET |
| AAQ1764 | 3 | SWIVEL NUT, FLARE |
| AAQ1791 | 30 | STREAMLINED WITH ONE BRAZING RING |
| AAQ1792 | 31 | STREAMLINE WITH TWO BRAZING RINGS |
| AAQ1793 | 32 | REDUCED SOCKET |
| AAQ1794 | 33 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAQ1795 | 34 | REDUCED GASKET SEAL |
| AAQ1796 | 35 | PLAIN |
| AAQ1797 | 36 | CRIMPED |
| AAQ1798 | 37 | GROOVED INSIDE |
| AAQ1799 | 38 | HOSE SOCKET |
| AAQ1800 | 39 | SOCKET W/BRAZING RING |
| AAQ1765 | 4 | SWIVEL NUT, GASKET SEAL |
| AAQ1801 | 40 | GASKET SEAL |
| AAQ1802 | 41 | BELL |
| AAQ1803 | 42 | DRESSER TYPE |
| AAQ1804 | 43 | DRESSER TYPE |
| AAQ1805 | 44 | PLAIN |
| AAQ1806 | 45 | GROOVED |
| AAQ1807 | 46 | BEADED |
| AAQ1808 | 47 | BEADED |
| AAQ1809 | 48 | SPIRALED |
| AAQ1810 | 49 | PLAIN BEVELED |
| AAQ1766 | 5 | GASKET SEAL |
| AAQ1811 | 50 | BARBED-BEADED |
| AAQ1812 | 51 | DOUBLE BEADED |
| AAQ1813 | 52 | MULTI-GROOVED |
| AAQ1814 | 53 | KNURLED |
| AAQ1767 | 6 | FLARE |
| AAQ1768 | 7 | INVERTED FLARE |
| AAQ1769 | 8 | SWIVEL NUT, COMPRESSION |
| AAQ1770 | 9 | SWIVEL NUT, FLARELESS |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAA2.0*;AARXJAA2.0$JAA2.0*;AARXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJHJTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAL*;BBRJDAM$$DAB*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AD | FLAMMABLE |
| AE | FRAGILE |
| AL | HUMIDITY CONTROLLED |
| AK | MAGNETIC |
| AM | SHOCK PROTECTED |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDB)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDAN*;ADZCDBQ$$DBV*)
| Table 1 |
| Reply Code (AA65) | Reply |
| A | ANY ACCEPTABLE |
| GK | CORROSION RESISTANT |
| BV | DUSTPROOF |
| BW | EXPLOSION PROOF |
| BQ | VAPOR |
| AN | WATER, FRESH |
| AP | WATER, SALT |
| BX | WATERTIGHT |
| AR | WEATHERPROOF |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDENA000*;SFTTDENA000$DENA000*;SFTTDENA000$$DENA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ENA000 | ENAMEL |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ052*;HZRDDHAZ008$$DHAZ030*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ222 | IRON |
| HAZ092 | MAGNESIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ052 | ZINC |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information