A ferrous or nonferrous wire having a solid cross section that is square or rectangular with sharp or rounded corners or edges, or is round, half-round, hexagonal, or octagonal and whose diameter, width, or greatest distance between parallel faces is less than 3/8 inch or 10.0mm. The rectangular shape is limited to a thickness less than 3/32 inch or 2.5mm and a width of 1 1/4 inch or 30.0mm or less. For dimensions greater than above, see BAR, METAL. Excludes:items having electrical resistivity or conductivity ratings.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED30889*)
CQBCJMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJPTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
CQHQJMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQHQJP2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST1212*;MATTDST0413$DFE0021*;MATTDST0413$$DFE0021*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL2117 | ALUMINUM ALLOY 2117 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5056 | ALUMINUM ALLOY 5056 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6062 | ALUMINUM ALLOY 6062 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CRB000 | CHROMIUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0059 | COPPER ALLOY 101 |
| CU0249 | COPPER ALLOY 102 |
| CU0286 | COPPER ALLOY 104 |
| CU0287 | COPPER ALLOY 105 |
| CU0288 | COPPER ALLOY 107 |
| CU0063 | COPPER ALLOY 110 |
| CU0289 | COPPER ALLOY 113 |
| CU0290 | COPPER ALLOY 114 |
| CU0291 | COPPER ALLOY 116 |
| CU0247 | COPPER ALLOY 120 |
| CU0323 | COPPER ALLOY 121 |
| CU0248 | COPPER ALLOY 122 |
| CU0292 | COPPER ALLOY 123 |
| CU0278 | COPPER ALLOY 125 |
| CU0324 | COPPER ALLOY 127 |
| CU0326 | COPPER ALLOY 128 |
| CU0315 | COPPER ALLOY 130 |
| CU0279 | COPPER ALLOY 142 |
| CU0069 | COPPER ALLOY 172 |
| CU0233 | COPPER ALLOY 173 |
| CU0074 | COPPER ALLOY 230 |
| CU0076 | COPPER ALLOY 240 |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU0103 | COPPER ALLOY 510 |
| CU0104 | COPPER ALLOY 511 |
| CU0206 | COPPER ALLOY 932 |
| AUA000 | GOLD |
| AUB000 | GOLD ALLOY |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FE0019 | IRON ALLOY 660 |
| FE0021 | IRON ALLOY 661 |
| FEG000 | IRON WROUGHT |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| MBA000 | MOLYBDENUM |
| NLB000 | NICKEL ALLOY |
| NL0043 | NICKEL ALLOY 205 |
| NL0008 | NICKEL ALLOY 400 |
| NL0009 | NICKEL ALLOY 600 |
| NL0010 | NICKEL ALLOY 718 |
| NL0017 | NICKEL ALLOY R-405 |
| PTA000 | PLATINUM |
| PTB000 | PLATINUM ALLOY |
| AGA000 | SILVER |
| AGF000 | SILVER ALLOY |
| AG0001 | SILVER UNS P07015 |
| STA000 | STEEL |
| ST1006 | STEEL COMP 1006 |
| ST1008 | STEEL COMP 1008 |
| ST1010 | STEEL COMP 1010 |
| ST1012 | STEEL COMP 1012 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1020 | STEEL COMP 1020 |
| ST1022 | STEEL COMP 1022 |
| ST1023 | STEEL COMP 1023 |
| ST0493 | STEEL COMP 1023W |
| ST1025 | STEEL COMP 1025 |
| ST1035 | STEEL COMP 1035 |
| ST1042 | STEEL COMP 1042 |
| ST1045 | STEEL COMP 1045 |
| ST1070 | STEEL COMP 1070 |
| ST1095 | STEEL COMP 1095 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1137 | STEEL COMP 1137 |
| ST1212 | STEEL COMP 1212 |
| ST1213 | STEEL COMP 1213 |
| ST0063 | STEEL COMP 12L14 |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0077 | STEEL COMP 303F |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0305 | STEEL COMP 305 |
| ST0310 | STEEL COMP 310 |
| ST0316 | STEEL COMP 316 |
| ST0321 | STEEL COMP 321 |
| ST0347 | STEEL COMP 347 |
| ST0403 | STEEL COMP 403 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST4140 | STEEL COMP 4140 |
| ST0416 | STEEL COMP 416 |
| ST0420 | STEEL COMP 420 |
| ST0430 | STEEL COMP 430 |
| ST4340 | STEEL COMP 4340 |
| ST0107 | STEEL COMP 440C |
| ST6150 | STEEL COMP 6150 |
| ST0630 | STEEL COMP 630 |
| ST0631 | STEEL COMP 631 |
| ST8630 | STEEL COMP 8630 |
| ST0028 | STEEL COMP E4340 |
| ST0030 | STEEL COMP E52100 |
| ST0413 | STEEL COMP H21 |
| ST0291 | STEEL COMP O1 |
| ST0292 | STEEL COMP O2 |
| ST0352 | STEEL COMP S5 |
| ST1575 | STEEL COMP W107 |
| ST0296 | STEEL COMP W108 |
| ST0297 | STEEL COMP W109 |
| ST0298 | STEEL COMP W110 |
| ST1576 | STEEL COMP W111 |
| ST0299 | STEEL COMP W112 |
| ST1577 | STEEL COMP W113 |
| ST0300 | STEEL COMP W114 |
| ST0306 | STEEL COMP W209 |
| ST0307 | STEEL COMP W210 |
| ST0187 | STEEL COMP XM-13 |
| STB000 | STEEL CORROSION RESISTING |
| ST0552 | STEEL UNS K02600 |
| ST1341 | STEEL UNS K06501 |
| ST0667 | STEEL UNS K06701 |
| ST0668 | STEEL UNS K08500 |
| ST1479 | STEEL UNS K15047 |
| ST1083 | STEEL UNS T12001 |
| TTA000 | TITANIUM ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) D7 OR D12 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ADVL)
IF STYLE/REPLY CODE(s) D8, D9 OR D10 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (BMNZ)
AGTALBASIC SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASIC APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AGTALD1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAR1893 | D1 | FLAT |
| AAR1898 | D10 | SQUARE |
| AAR1899 | D11 | HALF OVAL |
| AAR1900 | D12 | HALF ROUND |
| AAR1901 | D13 | OVAL |
| AAR1894 | D4 | ROUND W/ CORE |
| AAR1895 | D7 | ROUND |
| AAR1896 | D8 | HEXAGON |
| AAR1897 | D9 | OCTAGON |
ADVL*JCROSS SECTION OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVLJAA2.0*;ADVLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNZ*JCROSS-SECTIONAL WIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN CROSS-SECTIONAL FLATS,PERPENDICULAR TO THE HEIGHT OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNZJLA2.0*;BMNZJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNH*JCLADDING THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CLADDING COVERING THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNH3AFGJA2.0*;BMNH3AFGJA2.0$JA2.0*;BMNH3AFGJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AFG | BOTH SIDES |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) SNA000 OR ZNA000 WERE ENTERED FOR MRC SFTT, YOU MUST ANSWER MRC (BWDC)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDAUA000*;SFTTDAGA000$DCRA000*;SFTTDAGA000$$DCRA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| AUA000 | GOLD |
| PBA000 | LEAD |
| XXB000 | OXIDE |
| PSA000 | PASSIVATE |
| AGA000 | SILVER |
| SNA000 | TIN |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
BWDC*JCOATING WEIGHT
THE WEIGHT OF THE COATING TO BE APPLIED TO THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BWDCJBB2.0*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AP | GRAMS PER SQUARE METER |
| BB | OUNCES PER SQUARE FOOT |
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDQT*;HEATDBB$DGJ*;HEATDBB$$DGJ*)
| Table 1 |
| Reply Code (AD05) | Reply |
| GJ | AGE HARDENING |
| BP | ANNEALED |
| CK | ANNEALED TO A NOMINAL GRAIN SIZE 0.015 |
| CL | ANNEALED TO A NOMINAL GRAIN SIZE 0.025 |
| CM | ANNEALED TO A NOMINAL GRAIN SIZE 0.035 |
| CN | ANNEALED TO A NOMINAL GRAIN SIZE 0.050 |
| CP | ANNEALED TO A NOMINAL GRAIN SIZE 0.070 |
| CQ | ANNEALED TO A NOMINAL GRAIN SIZE 0.100 |
| FZ | ANNEALED TO A NOMINAL GRAIN SIZE 0.120 |
| HT | ARTIFICALLY AGED |
| MP | AS CAST |
| CS | AS FABRICATED |
| CZ | CASEHARDENED |
| CR | COLD DRAWN |
| DR | COLD DRAWN SOLUTION HEAT TREATED |
| HX | COLD DRAWN, SPRING TEMPER |
| HS | COLD FINISH |
| DA | COLD WORKED |
| LR | DRY ANNEALED |
| GA | EIGHTH HARD |
| GC | EXTRA HARD |
| GD | EXTRA SPRING TEMPER |
| CU | EXTRUDED |
| AD | F-AS FABRICATED |
| DN | H04 HARD |
| AE | H-1 STRAIN HARDENED |
| EX | H-111 STRAIN HARDENED |
| AV | H-112 AS ROLLED |
| GB | H-116 SPECIALLY TREATED |
| HJ | H-117 SPECIALLY TREATED |
| CA | H-12 STRAIN HARDENED, 1/2 HARD |
| AF | H-12 STRAIN HARDENED, 1/4 HARD |
| AG | H-14 STRAIN HARDENED, 1/2 HARD |
| AH | H-16 STRAIN HARDENED, 3/4 HARD |
| AJ | H-18 STRAIN HARDENED, FULL HARD |
| AK | H-19 STRAIN HARDENED, EXTRA HARD |
| PK | H-20 STRAIN HARDENED |
| PL | H-22 STRAIN HARDENED |
| PM | H-24 STRAIN HARDENED |
| PN | H-26 STRAIN HARDENED |
| PP | H-28 STRAIN HARDENED |
| PQ | H-32 STRAIN HARDENED |
| QP | H-321 STRAIN HARDENED |
| QQ | H-323 STRAIN HARDENED |
| PR | H-34 STRAIN HARDENED |
| QR | H-343 STRAIN HARDENED |
| PS | H-36 STRAIN HARDENED |
| PT | H-38 STRAIN HARDENED |
| CF | HALF HARD |
| CH | HARD |
| LS | HARD TEMPER |
| GY | INTERMEDIATE TEMPER |
| BC | LIGHT ANNEALED |
| DQ | LIGHTLY DRAWN |
| PW | NATURAL AGED |
| GZ | NITRIDED |
| CV | NORMALIZED |
| AB | O-ANNEALED |
| HB | OIL QUENCHED |
| PX | PARTIALLY ANNEALED |
| PZ | PARTIALLY ANNEALED TO 1/2 HARD |
| PY | PARTIALLY ANNEALED TO 1/4 HARD |
| QA | PARTIALLY ANNEALED TO 3/4 HARD |
| QB | PARTIALLY ANNEALED TO FULL HARD |
| DP | PRECIPITATION HEAT TREATED |
| MM | QQ-S-636, COND T-5, DEAD SOFT |
| CE | QUARTER HARD |
| DD | QUENCH HARDENED |
| EN | QUENCHED |
| CD | SKIN HARD |
| HD | SOFT |
| BB | SOFT ANNEALED |
| GE | SOFT TEMPER |
| EB | SOLUTION HEAT TREATED |
| GF | SOLUTION TREATED |
| LT | SPHERODIZE ANNEALED |
| BR | SPHEROIDIZED |
| CJ | SPRING TEMPER |
| PH | STABILIZED |
| QD | STABILIZED TO 1/2 HARD |
| QC | STABILIZED TO 1/4 HARD |
| QE | STABILIZED TO 3/4 HARD |
| QF | STABILIZED TO FULL HARD |
| ME | STRAIN HARDENED |
| CB | STRESS RELIEVED |
| QS | STRESS RELIEVED BY STRETCHING |
| GR | STRESSED RELIEVED |
| QT | T-1 SOLUTION HEAT TREATED |
| QG | T-3 SOLUTION HEAT TREATED |
| RB | T-351 SOLUTION HEAT TREATED |
| RF | T-3510 SOLUTION HEAT TREATED |
| RG | T-3511 SOLUTION HEAT TREATED |
| QH | T-36 SOLUTION HEAT TREATED |
| TM | T-361 SOLUTION HEAT TREATED |
| QJ | T-4 SOLUTION HEAT TREATED |
| RC | T-451 SOLUTION HEAT TREATED |
| RH | T-4510 SOLUTION HEAT TREATED |
| RJ | T-4511 SOLUTION HEAT TREATED |
| QW | T-5 SOLUTION HEAT TREATED |
| TC | T-52 SOLUTION HEAT TREATED |
| QK | T-6 SOLUTION HEAT TREATED |
| SD | T-62 SOLUTION HEAT TREATED |
| RD | T-651 SOLUTION HEAT TREATED |
| RK | T-6510 SOLUTION HEAT TREATED |
| RL | T-6511 SOLUTION HEAT TREATED |
| QY | T-73 SOLUTION HEAT TREATED |
| TB | T-7351 SOLUTION HEAT TREATED |
| RQ | T-73510 SOLUTION HEAT TREATED |
| RR | T-73511 SOLUTION HEAT TREATED |
| TN | T-7451 SOLUTION HEAT TREATED |
| QZ | T-76 SOLUTION HEAT TREATED |
| RM | T-7651 SOLUTION HEAT TREATED |
| RS | T-76510 SOLUTION HEAT TREATED |
| RT | T-76511 SOLUTION HEAT TREATED |
| QX | T-8 SOLUTION HEAT TREATED |
| QM | T-81 SOLUTION HEAT TREATED |
| RA | T-84 SOLUTION HEAT TREATED |
| RE | T-851 SOLUTION HEAT TREATED |
| RN | T-8510 SOLUTION HEAT TREATED |
| RP | T-8511 SOLUTION HEAT TREATED |
| QL | T-86 SOLUTION HEAT TREATED |
| FJ | T-87PRECIPITATION HEAT TREATED |
| KU | TEMPER DESIGNATION, O61 |
| UC | TEMPER DESIGNATION, T861 |
| EP | TEMPERED |
| CG | THREE QUARTERS HARD |
| DS | UNAGED |
SFCD*DSURFACE CONDITION
THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFCD3AEEDRT*;SFCD3AEEDRT$DCD*;SFCD3AEEDRT$$DCD*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACR | END |
| 3AEE | OVERALL |
| 3AFG | BOTH SIDES |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN72) | Reply |
| BB | BEST BRIGHT |
| BT | BRIGHT |
| CD | CENTERLESS GROUND |
| CP | CHROME PICKLED |
| CA | COLD DRAWN |
| CB | COLD FINISHED |
| DS | DESCALED |
| DL | DULL |
| DM | DULL MATTE |
| GR | GROUND |
| MA | MACHINE |
| AF | OIL FREE |
| AL | OILED |
| PK | PICKLED |
| PL | POLISHED |
| PG | PRECISION GROUND |
| RM | ROUGH MACHINED |
| RT | ROUGH TURNED |
| SB | SAND BLASTED |
| SN | SATIN |
| TN | TURNED |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJFC2.0*;ABRYJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVK*JCROSS SECTION INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVKJAA2.0*;ADVKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVM*JCROSS-SECTIONAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A CROSS SECTION,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVMJAB2.0*;ADVMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADWH*JCROSS-SECTIONAL WIDTH
A MEASUREMENT OF THE CROSS SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWHJLC2.0*;ADWHJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMPB*JCROSS-SECTIONAL RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMPBJAB2.0*;BMPBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BRFD*JWEIGHT PER UNIT MEASURE
THE WEIGHT OF THE ITEM WITH RESPECT TO A UNIT OF MEASURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRFDJAQ2.0*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AW | KILOGRAMS PER METER |
| AQ | KILOGRAMS PER SQUARE METER |
| BL | POUNDS PER LINEAR FOOT |
| BE | POUNDS PER PIECE |
| BD | POUNDS PER SQUARE FOOT |
AGUC*AUNIT PACKAGE QUANTITY
THE NUMBER OF ITEMS CONTAINED IN THE UNIT PACKAGE.
Enter the numeric reply with a minimum of one digit.
(AGUCA10*)
ALQG*DCONTAINER TYPE
INDICATES THE TYPE OF CONTAINER PROVIDED.
Enter the applicable reply code from the table below
(ALQGDAS*;ALQGDAB$DFY*;ALQGDAB$$DFY*)
| Table 1 |
| Reply Code (AF72) | Reply |
| AS | BAG |
| AB | BOX |
| CQ | CARTON |
| BF | DISPENSER |
| FY | DISPENSER, W/CUTTER |
| FS | PACKET |
| FX | SPOOL |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
| CB | CUBIC MILLIMETERS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDAZA000$DPDA000*;PRMTDAZA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000R2.0*;PMWTJRTA000R2.0$$JRTA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDAME*;ALBYDAMC$DBAR*;ALBYDAMC$$DBAR*)
| Table 1 |
| Reply Code (AH21) | Reply |
| AHX | AIRCRAFT |
| AAG | DENTAL |
| BAS | FOOD HANDLING |
| BAR | FOOD PROCESSING |
| AMD | HULL |
| AMC | SHIPBUILDING |
| AME | STRUCTURAL |
BRFB*JCOVERING AREA
THE AREA,PER UNIT OF WEIGHT,THE ITEM WILL COVER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRFBJHK2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| HJ | SQUARE INCHES PER POUND |
| HK | SQUARE MILLIMETERS PER KILOGRAM |
BRFC*DCOATING METHOD
THE MEANS BY WHICH THE COATING IS APPLIED.
Enter the applicable reply code from the table below
(BRFCDAE*;BRFCDAF$DAE*)
| Table 1 |
| Reply Code (AK01) | Reply |
| AE | ELECTROPLATED |
| AF | HOT DIPPED |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAC*;BBRGDAH$DAN*;BBRGDAH$$DAN*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ECWT*JEXTERIOR CONTAINER WEIGHT
THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ECWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information