An assemblage of an aircraft propeller hub and a set of aircraft propeller blades which in itself does not form a complete aircraft propeller.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED30769*)
IF STYLE/REPLY CODE(s) AAB WERE ENTERED FOR MRC AMWD, YOU MUST ANSWER MRC (BSYY)
IF STYLE/REPLY CODE(s) AAC WERE ENTERED FOR MRC AMWD, YOU MUST ANSWER MRC (AMWF and AQTG and AMWS and AMWT)
AMWDDPROPELLER TYPE
AN INDICATION OF THE TYPE OF PROPELLER.
Enter the applicable reply code from the table below
(AMWDDAAC)
| Table 1 |
| Reply Code (AJ25) | Reply |
| AAB | ADJUSTABLE PITCH |
| AAC | CONTROLLABLE PITCH |
| AAD | FIXED PITCH |
BSYY*DADJUSTMENT TYPE
INDICATES THE TYPE OF ADJUSTMENT INCLUDED IN THE ITEM.
Enter the applicable reply code from the table below
(BSYYDAAAR)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAAQ | CONTINUOUS |
| AAAR | STEPPED |
IF STYLE/REPLY CODE(s) AABF OR AAGB WERE ENTERED FOR MRC AMWF, YOU MUST ANSWER MRC (AMWG)
AMWF*DPITCH CONTROL TYPE
THE MEANS BY WHICH CHANGES OF BLADE PITCH ARE EFFECTED.
Enter the applicable reply code from the table below
(AMWFDAAGB)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAGB | ELECTRIC |
| AABF | HYDRAULIC |
| AADG | MECHANICAL |
| AAGC | PNEUMATIC |
AMWG*DPITCH CONTROL POWER SYSTEM
INDICATES WHETHER OR NOT THE PITCH CONTROL POWER SYSTEM IS SELF-CONTAINED.
Enter the applicable reply code from the table below
(AMWGDP)
| Table 1 |
| Reply Code (AJ26) | Reply |
| M | NOT SELF-CONTAINED |
| P | SELF-CONTAINED |
AQTG*DCONTROL METHOD
THE MEANS BY WHICH THE ITEM IS CONTROLLED.
Enter the applicable reply code from the table below
(AQTGDAAM*;AQTGDAAN$DAAN*)
| Table 1 |
| Reply Code (AL28) | Reply |
| AAM | AUTOMATIC |
| AAN | MANUAL |
AMWS*DFEATHERING FEATURE
AN INDICATION OF WHETHER OR NOT A FEATHERING FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(AMWSDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AMWT*DREVERSIBILITY
AN INDICATION OF WHETHER OR NOT AN ITEM IS REVERSIBLE.
Enter the applicable reply code from the table below
(AMWTDC)
| Table 1 |
| Reply Code (AF62) | Reply |
| B | NONREVERSIBLE |
| C | REVERSIBLE |
AMWWDROTATION DIRECTION
THE DIRECTION IN WHICH AN ITEM IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY.
Enter the applicable reply code from the table below
(AMWWDR*;AMWWDL$DL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
AMWYJSPAN MAXIMUM DIAMETER
THE MAXIMUM ALLOWABLE DIAMETER OF THE CIRCLE PRODUCED BY THE EXTREME TIP OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMWYJF2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
AJLBABLADE QUANTITY
THE NUMBER OF INDIVIDUAL BLADES INCLUDED.
Enter the numeric reply with a minimum of one digit.
(AJLBA10*)
AMXA*DBLADE FAIRING REMOVABILITY
AN INDICATION OF THE REMOVABILITY OF THE BLADE FAIRING.
Enter the applicable reply code from the table below
(AMXADC)
| Table 1 |
| Reply Code (AC29) | Reply |
| C | NONREMOVABLE |
| D | PARTIALLY REMOVABLE |
| B | REMOVABLE |
AMXQFBLADE ANGLE RANGE IN DEG
THE LIMITS OF BLADE PITCH ANGLE CHANGE FROM THE LOWEST TO THE HIGHEST,WITHIN WHICH THE ITEM WILL OPERATE,MEASURED FROM THE PLANE OF ROTATION AT A SPECIFIED LOCATION,EXPRESSED IN DEGREES.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AMXQFM2.0/P4.7*)
AMXRJDESIGN CONSTANT STATION RADIUS
THE DESIGN DISTANCE FROM THE AXIS OF ROTATION TO THE STATION OR POINT ON THE THRUST FACE OF THE BLADE AT WHICH THE BLADE ANGLES ARE SET OR MEASURED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMXRJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) AAB OR AAC WERE ENTERED FOR MRC AMXS, YOU MUST ANSWER MRC (AMXT)
AMXS*DICE CONTROL METHOD
THE MEANS USED TO CONTROL THE FORMATION OF ICE ON THE ITEM.
Enter the applicable reply code from the table below
(AMXSDAAB)
| Table 1 |
| Reply Code (AJ30) | Reply |
| AAB | ANTI-ICING |
| AAC | DEICING |
IF STYLE/REPLY CODE(s) GM WERE ENTERED FOR MRC AMXT, YOU MUST ANSWER MRC (AMXW)
AMXT*DICE CONTROL MEDIA
AN INDICATION OF THE SERVICE USED TO CONTROL ICE FORMATION ON THE ITEM.
Enter the applicable reply code from the table below
(AMXTDGN)
| Table 1 |
| Reply Code (AB75) | Reply |
| GM | ELECTRICITY |
| GP | HOT AIR |
| FG | HYDRAULIC FLUID |
| GN | ISOPROPYL SPRAY |
AMXW*DPOWER SOURCE LOCATION
INDICATES THE PHYSICAL LOCATION OF THE POWER SOURCE IN RELATION TO THE ITEM.
Enter the applicable reply code from the table below
(AMXWDABY)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAJ and AFYS and ANAH and ANAK and ABXV and ABRV and ABRR and AEVE)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAH and ANAJ and ABXV and AFYS and ADGE and ANAQ and ANAK and ABRV and ABRR and AEVE)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAJ and ABXV and ANAH and ADGE and AFYS and ANAX and ANAR and ANAQ and ANAW and ANAK and ABRV and ABRR and AEVE)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAT and ANAP and ANAS and ANAN and ANAJ and ANAH and ADGE and AFYS and ANAX and ANAR and ABXV and ANAQ and ANAW and ANAK and AEVE and ABRR and ABRV)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAJ and ANAH and ANAK and ABXV and ABTB and ABTJ and ABKG)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAH and ABXV and ANAK and ADGE and ANAJ and ANAN and AJFY and ANAP and ABKG and ABTJ and ABTB)
IF STYLE/REPLY CODE(s) 6A WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANBA and ANAZ and ANAH and ABXV and ANAK and ADGE and ANAJ and ANAN and AJFY and ANAP and ABKG)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAJ and ANAS and ANAT and ANAH and ADGE and ANAW and ANAK and ANAX and ABKG and ABTJ and ABXV and ABTB)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAK and ANAM and AFYS and ANAH and ANAL and ANAJ and ABRV and AEVE and ABRR)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAQ and ANAK and ANAR and ADGE and AFYS and ANAH and ANAL and ANAJ and ABRV and ABRR and AEVE and ANAM)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAX and ANAK and ANAW and ANAW and ANAM and ANAH and ANAR and AFYS and ADGE and ANAL and ANAJ and ABRV and ABRR and AEVE)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AMYP, YOU MUST ANSWER MRC (ANAJ and ANAS and ANAN and ANAP and ANAT and ADGE and AFYS and ANAH and ANAQ and ANAK and ANAW and ANAR and ANAX and ABRR and AEVE and ABRV and ANAL and ANAM)
AMYPLHUB SHAFT ACCOMMODATION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB SHAFT ACCOMMODATION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AMYPL3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAK1393 | 1 | STRAIGHT BORE W/ KEYWAY(S) |
| AAK1402 | 10 | TAPERED BORE W/ KEYWAY COUNTERBORED AFT END RECESSED FACE AFT END |
| AAK1403 | 11 | TAPERED BORE W/ KEYWAY COUNTERBORED BOTH ENDS RECESSED FACE BOTH ENDS |
| AAK1405 | 15 | STRAIGHT TOOTH SPLINES AND10527 |
| AAK1406 | 16 | INVOLUTE TOOTH SPLINES AND10529 |
| AAK1407 | 17 | STRAIGHT TOOTH SPLINES AND10530 |
| AAK1394 | 2 | STRAIGHT BORE W/ KEYWAY(S) COUNTERBORED AFT END |
| AAK1395 | 3 | STRAIGHT BORE W/ KEYWAY COUNTERBORED AFT END RECESSED FACE AFT END |
| AAK1396 | 4 | STRAIGHT BORE W/ KEYWAY COUNTERBORED BOTH ENDS RECESSED FACE BOTH ENDS |
| AAK1397 | 5 | STRAIGHT BORE W/ ADJACENT BOLT HOLES |
| DR00004 | 6 | COUNTERBORED FORWARD END W/ ADJACENT BOLT HOLES |
| AAK1398 | 6A | COUNTERBORED FORWARD END W/ ADJACENT COUNTERBORED BOLT HOLES |
| AAK1399 | 7 | STRAIGHT BORE W/ ADJACENT BOLT HOLES RECESSED FACE BOTH ENDS |
| AAK1400 | 8 | TAPERBORE W/ KEYWAY |
| AAK1401 | 9 | TAPERED BORE W/ KEYWAY(S) COUNTERBORED AFT END |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAC2.0*;ABKGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAC2.0*;ABKKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKU*JFLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKUJAA2.0*;ABKUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRR*JKEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRRJAC2.0*;ABRRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRV*JKEYWAY DEPTH
A MEASUREMENT FROM THE TOP SURFACE TO THE BOTTOM OF THE KEYWAY GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRVJAC2.0*;ABRVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABWV*JSHAFT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABWVJAA2.0*;ABWVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXV*JBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAB2.0*;ABXVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADGE*JBORE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A BORE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADGEJAC2.0*;ADGEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYS*JKEYWAY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEYWAY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYSJAB2.0*;AFYSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJLJ*JHUB LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJLJJAA2.0*;AJLJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAH*JHUB OVERALL LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAHJAB2.0*;ANAHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAJ*JHUB FORWARD FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAJJAC2.0*;ANAJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAK*JHUB AFT FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAKJAA2.0*;ANAKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAL*JTAPER BORE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANALJAC2.0*;ANALJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAM*JTAPER BORE MINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAMJAC2.0*;ANAMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAN*JFORWARD COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANANJAC2.0*;ANANJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAP*JFORWARD COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAPJAA2.0*;ANAPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAQ*JAFT COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAQJAB2.0*;ANAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAR*JAFT COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANARJAB2.0*;ANARJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAS*JFORWARD RECESSED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANASJAA2.0*;ANASJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAT*JFORWARD RECESSED FACE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANATJAA2.0*;ANATJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAW*JAFT RECESSED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAWJAA2.0*;ANAWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAX*JAFT RECESSED FACE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAXJAB2.0*;ANAXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAZ*JMOUNTING HOLE COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAZJAB2.0*;ANAZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANBA*JMOUNTING HOLE COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANBAJAB2.0*;ANBAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
AEVE*AKEYWAY QUANTITY
THE NUMBER OF KEYWAYS CONTAINED IN OR ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEVEA10*)
AJFY*BSEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AJFYB2.0)
AMYW*DBARREL TYPE
AN INDICATION OF THE TYPE OF BARREL INCLUDED.
Enter the applicable reply code from the table below
(AMYWDC)
| Table 1 |
| Reply Code (AC40) | Reply |
| C | SOLID |
| D | SPLIT |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AMZE*BROTATIONAL SPEED RATING IN RPM
THE SPEED AT WHICH AN ITEM HAS BEEN TESTED AND RATED TO PERFORM WITHOUT DAMAGE OR FAILURE OF THE ROTATING COMPONENTS,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMZEB2.0)
AMZJ*JPOWER ABSORPTION RATING
THE MAXIMUM AMOUNT OF POWER THAT AN ITEM IS DESIGNED TO ABSORB.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMZJJJL2.0*)
| Table 1 |
| Reply Code (AJ35) | Reply |
| HP | HORSEPOWER |
| JL | JOULES |
| KW | KILOWATTS |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
AMZN*ABLADE MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE BLADE.
Enter the alpha-numeric reply with five character(s) exactly.
(AMZNAL0Q1L)
AFZE*BOPERATING DC VOLTAGE IN VOLTS
THE DIRECT CURRENT POTENTIAL WHICH MUST BE APPLIED TO AN ITEM TO OBTAIN ITS RATED PERFORMANCE,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AFZEB2.0)
AMZZ*JHYDRAULIC SYSTEM FLUID CAPACITY
THE AMOUNT OF FLUID THAT THE HYDRAULIC SYSTEM WILL HOLD OR THAT IS REQUIRED FROM EXTERNAL SOURCES TO OPERATE THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMZZJG2.0*)
| Table 1 |
| Reply Code (AB10) | Reply |
| G | GALLONS |
| L | LITERS |
AAYJ*JHYDRAULIC FLUID FLOW RATE
THE AMOUNT OF HYDRAULIC FLUID REQUIRED TO OPERATE THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYJJM2.0*)
| Table 1 |
| Reply Code (AC64) | Reply |
| M | GALLONS PER MINUTE |
| E | LITERS PER MINUTE |
AAYK*JHYDRAULIC PRESSURE
THE GAGE PRESSURE REQUIRED TO OPERATE THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYKJG2.0*)
| Table 1 |
| Reply Code (AA95) | Reply |
| B | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
ACKL*DMEDIA FOR WHICH DESIGNED
THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACKLDAADQ*;ACKLDAADM$$DAADP*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AADM | HYDRAULIC FLUID, PHOSPHATE-ESTER BASE |
| AADN | HYDRAULIC FLUID, SILICATE-ESTER BASE |
| AABE | HYDRAULIC OIL |
| AADP | LUBRICATING OIL |
| AADQ | LUBRICATING OIL, DIESTER BASE |
| AADR | LUBRICATING OIL, ENGINE |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAA2.0*;AJAFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAB2.0*;AJAGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAA2.0*;AJAHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAY)
| Table 1 |
| Reply Code (AM83) | Reply |
| AY | MAGNET SENSITIVE |
| AK | MAGNETIC |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAN*;BBRGDAH$DAM*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDPDA000$DPTA000*;PRMTDPDA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000R2.0*;PMWTJRTA000R2.0$$JRTA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRTA0002.0*;PMLCJRTA0002.0$JRTA0002.0*;PMLCJRTA0002.0$$JRTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ008*;HZRDDHAZ052$$DHAZ030*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ052 | ZINC |
SHPN*ADOT PROPER SHIPPING NAME
THE PROPER SHIPPING NAME AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE.
Enter the alpha-numeric reply with a minimum of one character.
(SHPNAA7)
DENN*ADOT IDENTIFICATION NUMBER
THE IDENTIFICATION NUMBER ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PROPER SHIPPING NAME. IDENTIFICATION NUMBERS PRECEDED BY THE LETTERS "UN" ARE ASSOCIATED WITH INTERNATIONAL AS WELL AS DOMESTIC TRANSPORTATION AND THOSE PRECEDED BY THE LETTERS "NA" ARE NOT RECOGNIZED FOR INTERNATIONAL TRANSPORTATION OF HAZARDOUS MATERIALS (DANGEROUS GOODS) EXCEPT TO AND FROM THE UNITED STATES AND CANADA.
Enter the alpha-numeric reply with a minimum of one character.
(DENNAU7)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)