A computer which provides calculations for the delivery of fire-power to a predetermined target. Do not use if a more specific name can be found in this index. See also COMPUTER, DEPTH CHARGE RELEASE TIME; COMPUTER, POSITION BOMBING; and COMPUTER, TERRAIN CLEARANCE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED30747*)
AXQH*DINPUT INTELLIGENCE TYPE
INDICATES THE TYPE OF INTELLIGENCE THE ITEM IS CAPABLE OF RECEIVING.
Enter the applicable reply code from the table below
(AXQHDAHQ*;AXQHDADW$$DAGV*)
| Table 1 |
| Reply Code (AJ41) | Reply |
| AAX | ACCELERATION |
| AAY | AGC BIAS |
| AAZ | AIR DATA |
| ABA | AIR DENSITY |
| ABB | AIR DENSITY TIMES SPEED OF SOUND |
| ABC | AIR MILEAGE |
| ABD | AIR PRESSURE |
| AAB | AIR TEMPERATURE |
| ABE | AIRCRAFT DRIFT |
| ABF | AIRSPEED |
| ABG | ALTITUDE |
| ABK | ALTITUDE CORRECTION |
| ABH | ALTITUDE DATA |
| ABL | ALTITUDE DIFFERENTIAL COINCIDENCE |
| ABM | ALTITUDE DIFFERENTIAL CORRECTION |
| ABJ | ALTITUDE, GENERAL DATA |
| AQN | ANALOG |
| ABN | ANGLE OF ATTACK |
| ABP | ANTENNA AZIMUTH |
| ABQ | ANTENNA ELEVATION |
| ABR | ASTRO TRACKER |
| ABS | AUTOMATIC PILOT STEERING |
| ABT | AZIMUTH |
| ABW | AZIMUTH ANGLE |
| ABX | AZIMUTH DATA |
| ABY | BATHYTHERMOGRAPH DATA |
| ABZ | BEARING DISTANCE HEADING |
| ACA | BEARING RELATIVE |
| ACB | CENTER OF GRAVITY |
| ACC | CLASSIFIED |
| ACD | COMPASS HEADING |
| ACE | CONTINUOUS UPDATE OF COURSE |
| ACF | CONTROL |
| ACG | COURSE |
| ACH | COURSE RANGING |
| ACJ | COURSE TIMING REFERENCE |
| ACL | CROSS TRACK DISTANCE |
| ACK | CROSS TRACK SPEED ELEVATION |
| ACN | DEPRESSION SYSTEM DATA |
| ACM | DEPTH |
| ACP | DESTINATION LATITUDE |
| ACQ | DESTINATION LONGITUDE |
| ACR | DIFFERENTIAL PRESSURE |
| AQP | DIGITAL |
| ACS | DIGITIZER |
| ACT | DISPLACEMENT ANALOG DATA |
| AQS | DISTANCE |
| ACW | DISTANCE TO DESTINATION |
| ACX | DISTANCE TO GO |
| ACY | DOPPLER |
| ACZ | DOPPLER RADAR |
| ADA | DRIFT ANGLE |
| ADB | DYNAMIC PRESSURE |
| ADC | EAST |
| ADD | EAST DISTANCE |
| ADE | EAST-WEST |
| ADF | EAST-WEST AIRSPEED |
| ADG | EAST-WEST GROUND SPEED |
| ADH | ELEVATION |
| ADJ | ELEVATION ANGLE |
| ADK | ERROR |
| ADL | EXCESSIVE ERROR AND/OR POWER FAILURE MONITORING |
| ABU | FAIL-HARD |
| ABV | FAIL-SOFT |
| ADM | FINE RANGING |
| ADN | FINE TIMING RECEIVED |
| ADP | FIRING DATA |
| ADQ | FIXPOINT ELEVATION RANGE DATA |
| ADR | FLIGHT COMMAND INFORMATION |
| ADS | FORWARD |
| ADT | FUEL SENSOR |
| ADW | GROUND SPEED |
| ADX | GROUND TRACK |
| ADY | GROUND TRACK ANGLE |
| ADZ | GYROSCOPE-ALTITUDE DATA |
| AEB | HEADING CORRECTION |
| AEC | HEADING ERROR |
| AEA | HEADING-DRIFT VELOCITIES |
| AED | HORIZONTAL |
| AEE | HUMIDITY |
| AEF | INFRARED LOG SIGNAL STRENGTH |
| AEG | JUMP ANGLE OF MISSILE |
| AEH | JUMP ANGLE OF ROCKET |
| AEJ | LATITUDE |
| AEK | LAUNCH |
| AEL | LOCK-ON INDICATION |
| AEM | LONGITUDE |
| AEN | LORAN |
| AEP | MACH NUMBER |
| AEQ | MAGNETIC COMPASS |
| AET | MAGNETIC HEADING |
| AER | MAGNETIC VARIATION |
| AES | MAGNETIC VARIATION OF PRESENT POSITION |
| AEW | MANUAL ADJUSTMENT OF PITCH ALTITUDE REFERENCE TRIM |
| AEX | MANUAL SELECTION OF HEADING SYSTEM MADE |
| AEY | MANUAL SELECTION OF HEMISPHERE-LATITUDE OF OPERATION |
| AEZ | MANUAL SELECTION OF PRIMARY OR STANDBY MADE |
| AFA | MAPS COORDINATES VOLTAGE |
| ACV | MILLIVOLT |
| AFB | NAVAN |
| AFC | NAVIGATION COURSE SELECTED |
| AFD | NORTH |
| AFE | NORTH DISTANCE |
| AFF | NORTH-SOUTH |
| AFG | NORTH-SOUTH AIRSPEEDS |
| AFH | NORTH-SOUTH GROUND SPEED |
| AFJ | NOSE/TAIL INPUT |
| AFK | OBSERVER INPUT |
| AFL | OFF TARGET |
| AFM | ON TARGET |
| AFN | OWN SHIP COURSE |
| AFP | OWN SHIP DISTANCE |
| AFQ | OWN SHIP DISTANCE W/RESPECT TO NORTH AND EAST |
| AFR | OWN SHIP SPEED |
| AFS | OWN SHIP SPEED EAST |
| AFT | OWN SHIP SPEED NORTH |
| AFW | PEN CONTROL VOLTAGE |
| AFY | PITCH ANGLE |
| AFX | PITCH-ROLL SIGNAL DATA |
| AFZ | PLATFORM DRIVE SIGNALS |
| AGA | PRESENT POSITION |
| AGB | PRESENT POSITION LATITUDE-LONGITUDE |
| AAF | PRESSURE |
| AGC | PRESSURE ALTITUDE |
| AGD | RADAR POSITION DATA |
| AGE | RADAR RANGE |
| AGF | RADAR TRIGGER DATA |
| AGG | RADAR VIDEO DATA |
| AGH | RANGE |
| AGJ | RANGE DATA |
| AGK | RANGE RATE |
| AGL | RANGE VOLTAGE |
| AGM | RELATIVE BEARING |
| AGN | RELATIVE COURSE ANGLE |
| AGP | RELATIVE GROUND TRACK |
| AGQ | RELEASE |
| APL | ROENTGENS |
| AGR | SERVO AMPLIFIER |
| AGS | SERVO LOOP |
| AGT | SEXTANT |
| AGW | SHIP COURSE |
| AGX | SHIP DISTANCE |
| AGY | SLANT RANGE TO RANGE |
| AGZ | SPEED |
| AHA | STABILIZATION DATA |
| AHB | STAGNATION TEMP |
| AHC | STATIC PRESSURE |
| AHD | STEERING DATA TO DESTINATION |
| AHE | SWEEP |
| AHF | SYNCHRO MOTOR |
| AHG | TACAN |
| AHH | TACHOMETER AMPLIFIER |
| AHJ | TARGET ALTITUDE |
| AHK | TARGET ASPECT VOLTAGE |
| AHL | TARGET AZIMUTH |
| AHM | TARGET BEARING |
| AHN | TARGET COURSE |
| AHP | TARGET DEPTH |
| AHQ | TARGET DISTANCE |
| AHR | TARGET ECHO |
| AHS | TARGET ELEVATION |
| AHT | TARGET ELEVATION ANGLE |
| AHW | TARGET HEIGHT |
| AHX | TARGET POSITION |
| AHY | TARGET RANGE |
| AHZ | TARGET RATE |
| AJA | TARGET SPEED |
| AAL | TEMPERATURE |
| AJB | TIME |
| AJC | TIME BASE TRIGGER PULSE |
| AJD | TIME/HOURS |
| AJE | TIME/MINUTES |
| AJF | TORQUING SIGNAL EARTH RATE CORRECTION |
| AJG | TORQUING SIGNAL TRANSPORT |
| AJH | TOTAL MILES COUNTER |
| ACU | TOTAL NUMBER OF RANDOM PULSES |
| AJJ | TOTAL PRESSURE |
| AJK | TRACK EAST |
| AJL | TRACK ERROR DATA |
| AJM | TRACK NORTH |
| AJN | TRAIL |
| AJP | TRIGGER AND GATE VOLTAGES |
| AJQ | TRIGGER PULSE |
| AJR | TRUE AIR SPEED |
| AJS | TRUE ALTITUDE |
| AJT | TRUE ANGLE OF ATTACK |
| AJW | TRUE HEADING |
| AJX | VARIATION |
| AJY | VELOCITY |
| AJZ | VELOCITY SIGNAL TIMES AXIS |
| AKA | VELOCITY SIGNAL Y AXIS |
| AKB | VERTICAL ACCELERATION SIGNAL |
| AKC | VIDEO RETURN FROM 0 TO 20000 YARDS |
| AKD | WARNING |
| AKE | WEIGHT |
| AAM | WIND DIRECTION |
| AKF | WIND FORCE |
| AAN | WIND SPEED |
| AKG | WIND VELOCITY |
| ADU | ZOOM |
AXQJDINTELLIGENCE INPUT METHOD
THE MEANS USED TO INPUT THE INTELLIGENCE.
Enter the applicable reply code from the table below
(AXQJDAAAE*;AXQJDAADG$DAABE*)
| Table 1 |
| Reply Code (AC58) | Reply |
| AABE | AIR |
| AAAE | ELECTRICAL |
| AADG | MECHANICAL |
AXQK*DOUTPUT INTELLIGENCE TYPE
INDICATES THE TYPE OF INTELLIGENCE THE ITEM IS CAPABLE OF TRANSMITTING.
Enter the applicable reply code from the table below
(AXQKDAKD*;AXQKDAED$$DADN*)
| Table 1 |
| Reply Code (AJ41) | Reply |
| AAX | ACCELERATION |
| AAY | AGC BIAS |
| AAZ | AIR DATA |
| ABA | AIR DENSITY |
| ABB | AIR DENSITY TIMES SPEED OF SOUND |
| ABC | AIR MILEAGE |
| ABD | AIR PRESSURE |
| AAB | AIR TEMPERATURE |
| ABE | AIRCRAFT DRIFT |
| ABF | AIRSPEED |
| ABG | ALTITUDE |
| ABK | ALTITUDE CORRECTION |
| ABH | ALTITUDE DATA |
| ABL | ALTITUDE DIFFERENTIAL COINCIDENCE |
| ABM | ALTITUDE DIFFERENTIAL CORRECTION |
| ABJ | ALTITUDE, GENERAL DATA |
| AQN | ANALOG |
| ABN | ANGLE OF ATTACK |
| ABP | ANTENNA AZIMUTH |
| ABQ | ANTENNA ELEVATION |
| ABR | ASTRO TRACKER |
| ABS | AUTOMATIC PILOT STEERING |
| ABT | AZIMUTH |
| ABW | AZIMUTH ANGLE |
| ABX | AZIMUTH DATA |
| ABY | BATHYTHERMOGRAPH DATA |
| ABZ | BEARING DISTANCE HEADING |
| ACA | BEARING RELATIVE |
| ACB | CENTER OF GRAVITY |
| ACC | CLASSIFIED |
| ACD | COMPASS HEADING |
| ACE | CONTINUOUS UPDATE OF COURSE |
| ACF | CONTROL |
| ACG | COURSE |
| ACH | COURSE RANGING |
| ACJ | COURSE TIMING REFERENCE |
| ACL | CROSS TRACK DISTANCE |
| ACK | CROSS TRACK SPEED ELEVATION |
| ACN | DEPRESSION SYSTEM DATA |
| ACM | DEPTH |
| ACP | DESTINATION LATITUDE |
| ACQ | DESTINATION LONGITUDE |
| ACR | DIFFERENTIAL PRESSURE |
| AQP | DIGITAL |
| ACS | DIGITIZER |
| ACT | DISPLACEMENT ANALOG DATA |
| AQS | DISTANCE |
| ACW | DISTANCE TO DESTINATION |
| ACX | DISTANCE TO GO |
| ACY | DOPPLER |
| ACZ | DOPPLER RADAR |
| ADA | DRIFT ANGLE |
| ADB | DYNAMIC PRESSURE |
| ADC | EAST |
| ADD | EAST DISTANCE |
| ADE | EAST-WEST |
| ADF | EAST-WEST AIRSPEED |
| ADG | EAST-WEST GROUND SPEED |
| ADH | ELEVATION |
| ADJ | ELEVATION ANGLE |
| ADK | ERROR |
| ADL | EXCESSIVE ERROR AND/OR POWER FAILURE MONITORING |
| ABU | FAIL-HARD |
| ABV | FAIL-SOFT |
| ADM | FINE RANGING |
| ADN | FINE TIMING RECEIVED |
| ADP | FIRING DATA |
| ADQ | FIXPOINT ELEVATION RANGE DATA |
| ADR | FLIGHT COMMAND INFORMATION |
| ADS | FORWARD |
| ADT | FUEL SENSOR |
| ADW | GROUND SPEED |
| ADX | GROUND TRACK |
| ADY | GROUND TRACK ANGLE |
| ADZ | GYROSCOPE-ALTITUDE DATA |
| AEB | HEADING CORRECTION |
| AEC | HEADING ERROR |
| AEA | HEADING-DRIFT VELOCITIES |
| AED | HORIZONTAL |
| AEE | HUMIDITY |
| AEF | INFRARED LOG SIGNAL STRENGTH |
| AEG | JUMP ANGLE OF MISSILE |
| AEH | JUMP ANGLE OF ROCKET |
| AEJ | LATITUDE |
| AEK | LAUNCH |
| AEL | LOCK-ON INDICATION |
| AEM | LONGITUDE |
| AEN | LORAN |
| AEP | MACH NUMBER |
| AEQ | MAGNETIC COMPASS |
| AET | MAGNETIC HEADING |
| AER | MAGNETIC VARIATION |
| AES | MAGNETIC VARIATION OF PRESENT POSITION |
| AEW | MANUAL ADJUSTMENT OF PITCH ALTITUDE REFERENCE TRIM |
| AEX | MANUAL SELECTION OF HEADING SYSTEM MADE |
| AEY | MANUAL SELECTION OF HEMISPHERE-LATITUDE OF OPERATION |
| AEZ | MANUAL SELECTION OF PRIMARY OR STANDBY MADE |
| AFA | MAPS COORDINATES VOLTAGE |
| ACV | MILLIVOLT |
| AFB | NAVAN |
| AFC | NAVIGATION COURSE SELECTED |
| AFD | NORTH |
| AFE | NORTH DISTANCE |
| AFF | NORTH-SOUTH |
| AFG | NORTH-SOUTH AIRSPEEDS |
| AFH | NORTH-SOUTH GROUND SPEED |
| AFJ | NOSE/TAIL INPUT |
| AFK | OBSERVER INPUT |
| AFL | OFF TARGET |
| AFM | ON TARGET |
| AFN | OWN SHIP COURSE |
| AFP | OWN SHIP DISTANCE |
| AFQ | OWN SHIP DISTANCE W/RESPECT TO NORTH AND EAST |
| AFR | OWN SHIP SPEED |
| AFS | OWN SHIP SPEED EAST |
| AFT | OWN SHIP SPEED NORTH |
| AFW | PEN CONTROL VOLTAGE |
| AFY | PITCH ANGLE |
| AFX | PITCH-ROLL SIGNAL DATA |
| AFZ | PLATFORM DRIVE SIGNALS |
| AGA | PRESENT POSITION |
| AGB | PRESENT POSITION LATITUDE-LONGITUDE |
| AAF | PRESSURE |
| AGC | PRESSURE ALTITUDE |
| AGD | RADAR POSITION DATA |
| AGE | RADAR RANGE |
| AGF | RADAR TRIGGER DATA |
| AGG | RADAR VIDEO DATA |
| AGH | RANGE |
| AGJ | RANGE DATA |
| AGK | RANGE RATE |
| AGL | RANGE VOLTAGE |
| AGM | RELATIVE BEARING |
| AGN | RELATIVE COURSE ANGLE |
| AGP | RELATIVE GROUND TRACK |
| AGQ | RELEASE |
| APL | ROENTGENS |
| AGR | SERVO AMPLIFIER |
| AGS | SERVO LOOP |
| AGT | SEXTANT |
| AGW | SHIP COURSE |
| AGX | SHIP DISTANCE |
| AGY | SLANT RANGE TO RANGE |
| AGZ | SPEED |
| AHA | STABILIZATION DATA |
| AHB | STAGNATION TEMP |
| AHC | STATIC PRESSURE |
| AHD | STEERING DATA TO DESTINATION |
| AHE | SWEEP |
| AHF | SYNCHRO MOTOR |
| AHG | TACAN |
| AHH | TACHOMETER AMPLIFIER |
| AHJ | TARGET ALTITUDE |
| AHK | TARGET ASPECT VOLTAGE |
| AHL | TARGET AZIMUTH |
| AHM | TARGET BEARING |
| AHN | TARGET COURSE |
| AHP | TARGET DEPTH |
| AHQ | TARGET DISTANCE |
| AHR | TARGET ECHO |
| AHS | TARGET ELEVATION |
| AHT | TARGET ELEVATION ANGLE |
| AHW | TARGET HEIGHT |
| AHX | TARGET POSITION |
| AHY | TARGET RANGE |
| AHZ | TARGET RATE |
| AJA | TARGET SPEED |
| AAL | TEMPERATURE |
| AJB | TIME |
| AJC | TIME BASE TRIGGER PULSE |
| AJD | TIME/HOURS |
| AJE | TIME/MINUTES |
| AJF | TORQUING SIGNAL EARTH RATE CORRECTION |
| AJG | TORQUING SIGNAL TRANSPORT |
| AJH | TOTAL MILES COUNTER |
| ACU | TOTAL NUMBER OF RANDOM PULSES |
| AJJ | TOTAL PRESSURE |
| AJK | TRACK EAST |
| AJL | TRACK ERROR DATA |
| AJM | TRACK NORTH |
| AJN | TRAIL |
| AJP | TRIGGER AND GATE VOLTAGES |
| AJQ | TRIGGER PULSE |
| AJR | TRUE AIR SPEED |
| AJS | TRUE ALTITUDE |
| AJT | TRUE ANGLE OF ATTACK |
| AJW | TRUE HEADING |
| AJX | VARIATION |
| AJY | VELOCITY |
| AJZ | VELOCITY SIGNAL TIMES AXIS |
| AKA | VELOCITY SIGNAL Y AXIS |
| AKB | VERTICAL ACCELERATION SIGNAL |
| AKC | VIDEO RETURN FROM 0 TO 20000 YARDS |
| AKD | WARNING |
| AKE | WEIGHT |
| AAM | WIND DIRECTION |
| AKF | WIND FORCE |
| AAN | WIND SPEED |
| AKG | WIND VELOCITY |
| ADU | ZOOM |
AMKD*DINDICATOR TYPE
INDICATES THE TYPE OF DEVICE USED TO REGISTER THE CONDITION(S).
Enter the applicable reply code from the table below
(AMKDDAMD*;AMKDDAFL$$DAFH*)
| Table 1 |
| Reply Code (AJ12) | Reply |
| AFF | ALPHA-NUMERIC ELECTRONIC TUBE |
| AFE | AUDIO TONE |
| AHU | AUXILLIARY CATHODE RAY TUBE |
| ADS | CATHODE RAY TUBE |
| AMD | DIGITAL READOUT |
| AFG | DUAL ROTATING DIAL |
| ANE | ELECTROLUMINESCENT DISPLAY |
| AFH | ELECTRONIC COUNTER |
| ANF | GAS PLASMA |
| AFJ | GLOW TUBE |
| ACE | LIGHT |
| AND | LIQUID CRYSTAL DISPLAY (LCD) |
| AFK | MECHANICAL COUNTER |
| ACJ | METER |
| AHV | REMOTE |
| AFL | SINGLE ROTATING DIAL |
AWZJDPOWER SOURCE
THE SOURCE OF POWER WHICH PROVIDES THE ENERGY REQUIRED FOR THE OPERATION OF THE ITEM.
Enter the applicable reply code from the table below
(AWZJDBJ*;AWZJDBH$DBH*)
| Table 1 |
| Reply Code (AG27) | Reply |
| BJ | EXTERNAL |
| BH | SELF-CONTAINED |
ACUR*BDIRECT CURRENT VOLTAGE RATING IN VOLTS
THE DIRECT CURRENT VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACURB2.0*;ACURB2.0$$BM2.0*)
IF YOU ANSWER MRC ACUQ, YOU MUST ANSWER MRC (FREQ and FAAZ)
ACUQ*BALTERNATING CURRENT VOLTAGE RATING IN VOLTS
THE ALTERNATING CURRENT VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACUQB2.0*;ACUQB2.0$$BM2.0*)
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0*;FREQB2.0$$BM2.0*)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDC$$DB*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0*;AMPSB2.0$$BM2.0*)
IF STYLE/REPLY CODE(s) BP OR BQ WERE ENTERED FOR MRC AARB, YOU MUST ANSWER MRC (AEEE and AEEF)
AARB*DTERMINAL TYPE
INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. PLEASE USE MRC CSCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AARBDBP*;AARBDBQ$$DBE*)
| Table 1 |
| Reply Code (AA58) | Reply |
| BP | CONNECTOR, PLUG |
| BQ | CONNECTOR, RECEPTACLE |
| BE | SCREW |
AARA*ATERMINAL QUANTITY
THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARAA10*)
AEEF*ACONNECTOR MANUFACTURER PART NUMBER
THE IDENTIFYING PART NUMBER ASSIGNED TO THE ELECTRICAL CONNECTOR RECEPTACLE.
Enter the alpha-numeric reply with a minimum of one character.
(AEEFAF4)
AEEE*ACONNECTOR MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ELECTRICAL CONNECTOR RECEPTACLE.
Enter the alpha-numeric reply with five character(s) exactly.
(AEEEAX5B6M)
APXH*DTERMINAL LOCATION
THE POSITION OF THE TERMINAL/S/ FOR MAKING CONNECTION TO AN ITEM.PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(APXHDABA*;APXHDARW$$DAHP*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| AAZ | BACK |
| ART | BACK CORNER |
| AAX | BASE |
| ABA | BOTTOM |
| AHP | CENTER |
| AGW | COVER |
| ABB | END |
| ABC | FRONT |
| ARW | FRONT CORNER |
| ABT | FRONT END |
| ADD | ONE SIDE |
| ACZ | SIDE |
| ABD | TOP |
AAXX*DMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDCL*;AAXXDDC$DFL*)
| Table 1 |
| Reply Code (AA78) | Reply |
| BF | BASE |
| FH | BASE, SHOCK MOUNT |
| CL | BRACKET |
| FJ | CLAMP |
| FK | DRAWER |
| DC | FIXED |
| CW | FLANGE |
| CJ | PANEL |
| FL | PLATE |
| FM | RACK |
| FN | VIBRATION, BEAM |
| FP | VIBRATION, CUP |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBCE*;CBBLDCEN$$DDMF*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BKR | ELECTRICALLY INSULATED |
| DBN | ELECTROMAGNETIC INTERFERENCE SHIELDING |
| BSZ | ELECTROSTATIC SENSITIVE |
| BCE | RADIATION TOLERANT |
| AGQ | RFI SHIELDING |
| CEN | RUGGEDIZED |
| DMF | TEMPEST |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG3)
| Table 1 |
| Reply Code (EN02) | Reply |
| AB | BRONZE - EPEAT REGISTERED PRODUCTS |
| LF | COMPUTERS-DESKTOPS, WORKSTATIONS, AND THIN CLIENTS - ENERGY STAR-INFORMATION TECHNOLOGY - ENERGY EFFICIENT PRODUCTS |
| JW | ENERGY EFFICIENT - FEMP - LOW STANDBY POWER - OFFICE EQUIPMENT - COMPUTER WORKSTATION |
| JX | ENERGY EFFICIENT - FEMP - LOW STANDBY POWER - OFFICE EQUIPMENT - DOCKING STATIONS |
| JY | ENERGY EFFICIENT - FEMP - LOW STANDBY POWER - OFFICE EQUIPMENT - MULTIFUNCTION DEVICES |
| G3 | ENERGY EFFICIENT - FEMP - LOW STANDBY POWER - OFFICE EQUIPMENT -INTEGRATED COMPUTERS |
| AG | GOLD - EPEAT REGISTERED PRODUCTS |
| JZ | IMAGING EQUIPMENT-SCANNERS - ENERGY STAR-INFORMATION TECHNOLOGY - ENERGY EFFICIENT PRODUCTS |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
| AF | SILVER - EPEAT REGISTERED PRODUCTS |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE*;BBRJDAH$DAK*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AE | FRAGILE |
| AK | MAGNETIC |
| AH | RADIOACTIVE |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDE*;AFJNDG$DF*)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRTA000*;PRMTDIRA000$DPTA000*;PRMTDIRA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000E2.0*;PMWTJAUA000E2.0$JAUA000E2.0*;PMWTJAUA000E2.0$$JAUA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDENA000*;SFTTDENA000$DENA000*;SFTTDENA000$$DENA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ENA000 | ENAMEL |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAB2.0*;AJAFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJFA2.0*;AJAGJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAA2.0*;AJAHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAD*;BBRGDAJ$DAH*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAM4)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAA4)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ008*;HZRDDHAZ008$$DHAZ008*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information