Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
BP10024	B1	BALL
BP10033	B10	BUTTON
BP10034	B11	SQUARE
BP10035	B12	FILLISTER
BP10036	B13	OVAL
BP10037	B14	ROOF
BP10038	B15	ROUND
BP10039	B16	TRUSS
BP10040	B17	WATERTIGHT
BP10041	B18	WEATHERTIGHT
BP10042	B19	FLAT
BP10025	B2	BEVEL
BP10043	B20	PAN
BP10044	B21	PAN NO. 2
BP10045	B22	FLAT FILLISTER
BP10046	B23	MODIFIED PAN
BP10047	B24	UNDERCUT PAN NO. 2
BP10048	B25	FLAT CHAMFER
BP10049	B26	RIBBED
BP10050	B27	ROUND WITH WRENCH FLATS CHAMFERED
BP10051	B28	ROUND WITH WRENCH FLATS
BP10052	B29	ROUND WEDGE
BP10026	B3	BLIND
BP10053	B30	SQUARE WEDGE
BP10054	B31	DEE CHAMFER
BP10055	B32	UNDERCUT UNIVERSAL
BP10056	B33	DEE
BP10057	B34	DISHED COUNTERSUNK
BP10058	B35	FILLISTER COUNTERSUNK
BP10059	B36	FLAT COUNTERSUNK
BP10060	B37	FLAT TOP ELEVATOR
BP10061	B38	FLAT COUNTERSUNK UNDERCUT
BP10062	B39	HEXAGON COUNTERSUNK
BP10027	B4	DOUBLE CHAMFER
BP10063	B40	HEXAGON COUNTERSUNK UNDERCUT
BP10064	B41	OVAL COUNTERSUNK
BP10065	B42	SQUARE COUNTERSUNK
BP10066	B43	OVAL COUNTERSUNK UNDERCUT
BP10067	B44	ROUND COUNTERSUNK
BP10068	B45	DISHED HEXAGON
BP10069	B46	DOUBLE HEXAGON
BP10070	B47	HEXAGON
BP10071	B48	CROWNED HEXAGON
BP10072	B49	FLAT COUNTERSUNK REVERSE KEYED
BP10028	B5	DRIVE
BP10073	B50	FLAT COUNTERSUNK REVERSE KEYED NO. 2
BP10074	B51	FLAT COUNTERSUNK KEYED
BP10075	B52	SINGLE CHAMFER KEYED
BP10076	B53	FLAT COUNTERSUNK PARALLEL KEYED
BP10077	B54	FLAT KEYED
BP10078	B55	DOUBLE HEXAGON EXTENDED WASHER NO. 1
BP10079	B56	HEXAGON EXTENDED WASHER
BP10080	B57	SQUARE EXTENDED WASHER
BP10081	B58	ROUND EXTENDED WASHER
BP10082	B59	SWIVEL HANDLE
BP10029	B6	FLUSH
BP10083	B60	SPADE
BP10084	B61	SLIDING HANDLE
BP10085	B62	WATERTIGHT HEXAGON
BP10086	B63	FILLISTER EXTENDED WASHER
BP10087	B64	BOILER PATCH NO. 1
BP10088	B65	BOILER PATCH NO. 2
BP10089	B66	BOILER PATCH NO. 3
BP10090	B67	KNURLED NO. 1
BP10091	B68	KNURLED NO. 2
BP10092	B69	KNURLED NO. 3
BP10030	B7	HOOK
BP10093	B70	KNURLED NO. 4
BP10094	B71	KNURLED NO. 5
BP10095	B72	KNURLED NO. 6
BP10096	B73	TEE NO. 1
BP10098	B75	TEE NO. 3
BP10099	B76	TEE NO. 4
BP10100	B77	TEE NO. 5
BP10101	B78	TEE NO. 6
BP10102	B79	THUMB NO. 1
BP10031	B8	OFFSET SPADE
DR04099	B80	THUMB NO.2
BP10104	B81	THUMB NO. 3
BP10105	B82	THUMB NO. 4
BP10106	B83	THUMB NO. 5
BP10107	B84	THUMB NO. 6
BP10108	B85	THUMB NO. 7
BP10109	B86	THUMB NO. 8
BP10110	B87	THUMB NO. 9
BP10111	B88	WING NO. 1
BP10112	B89	WING NO. 2
BP10032	B9	BINDING
BP10113	B90	WING NO. 3
BP10114	B91	WING NO. 4

AASL*JHEAD DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASLJAB2.0*;AASLJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASM*JBOTTOM COUNTERSINK DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASMJAA2.0*;AASMJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASN*JHANDLE LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASNJAA2.0*;AASNJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASP*JHANDLE WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HANDLE,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASPJAB2.0*;AASPJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASQ*JHANDLE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HANDLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASQJAB2.0*;AASQJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASR*JHEAD INSIDE DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASRJAA2.0*;AASRJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AAST*JKEY LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASTJAC2.0*;AASTJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASU*JHEAD HEIGHT

A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEAD,IN DISTINCTION FROM DEPTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASUJAB2.0*;AASUJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASV*JHEAD LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASVJAC2.0*;AASVJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASW*JKEY PROJECTION LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASWJAC2.0*;AASWJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASX*JTEE BOLT CYLINDRICAL HEAD DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASXJAC2.0*;AASXJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AASY*JDISTANCE FROM CENTERLINE TO FLAT

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AASYJAB2.0*;AASYJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AATC*JEXTENDED WASHER DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AATCJAC2.0*;AATCJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AATD*JEXTENDED WASHER THICKNESS

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AATDJAB2.0*;AATDJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABRY*JLENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ASDB*JWIDTH ACROSS FLATS

THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ASDBJAC2.0*;ASDBJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AATA*BCOUNTERSINK ANGLE IN DEG

THE INCLUDED ANGLE OF THE COUNTERSINK,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AATAB2.0)

AATE*BCHAMFER ANGLE IN DEG

THE MEASUREMENT OF THE CHAMFER ANGLE,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AATEB2.0)

BZGFLRECESSED DRIVE STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RECESSED DRIVE.

(BZGFLC13)

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
BP10115	C1	CROSS RECESS TYPE 1
BP10124	C10	TORQUE
BP10125	C11	CROSS RECESS TYPE 1A
BP10126	C12	CLUTCH TYPE 1
BP10127	C13	CLUTCH TYPE 11
BP10128	C14	ONE WAY
BP10129	C15	SLOT
BP10130	C16	FOUR SPANNER
BP10131	C17	SOCKET
BP10132	C18	FOUR SPLINE
BP10116	C2	CROSS RECESS TYPE 11
BP10117	C3	CROSS RECESS TYPE 111
BP10118	C4	DOUBLE HEXAGON
BP10119	C5	SOCKET
BP10120	C6	RECESSED TYPE 1
BP10121	C7	SIX SPLINE
BP10122	C8	TORQUE SET
BP10123	C9	HIGH-TORQUE

BBDT*DPOINT TYPE

INDICATES THE TYPE OF POINT(S) PROVIDED ON THE ITEM.

Enter the applicable reply code from the table below

(BBDTDAGD)

Table 1
	Reply Code (AJ44)	Reply
	AAB	BALL
	AFY	BAYONET
	AFZ	BEVEL
	AGA	BLUNT
	AGB	BONE INSULATED
	AGC	BOTH BLUNT
	AGD	BOTH SHARP
	AGE	CLOVERLEAF
	AGF	CONE
	AGG	CYLINDRICAL
	AHH	DIAMOND
	APB	DIAMOND POINT, BOTH ENDS
	AGH	DOG
	AGJ	FLAT STAR
	AGK	FLAT WIRE
	AGL	FLUTED
	AGM	KNIFE
	AAA	KNOB
	AGN	NEEDLE
	AGP	OLIVARY POINTED
	AGQ	ONE BLUNT
	AGR	ONE SHARP
	AGS	PILOT
	APC	PLAIN SHANK, DIAMOND POINT
	APD	PLAIN SHANK, TROCAR POINT
	AGT	PROBE HOOK
	AGW	PROBE POINTED
	AGX	ROUND BLUNT
	AAU	ROUND LOOP
	AGY	ROUND WIRE
	AGZ	SAW
	AHA	SHARP
	AHB	STANDARD
	AHC	TAPERED STAR
	APE	THREE SIDED SHANK, DIAMOND POINT
	APF	THREE SIDED SHANK, TROCAR POINT
	AHD	TROCAR
	APG	TROCAR POINT, BOTH ENDS
	AHE	TROCAR POINTED
	AHF	TWIST DRILL
	AJT	VERTICAL

ABHPJOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

PRMT*DPRECIOUS MATERIAL

IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.

Enter the applicable reply code from the table below

(PRMTDAUA000*;PRMTDIRA000$DRTA000*;PRMTDIRA000$$DRTA000*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

PMWT*JPRECIOUS MATERIAL AND WEIGHT

AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(PMWTJAGA000F2.0*;PMWTJAGA000F2.0$$JAGA000F2.1*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

Table 2
	Reply Code (AG14)	Reply
	E	GRAINS, TROY
	R	GRAMS
	F	OUNCES, TROY

PMLC*JPRECIOUS MATERIAL AND LOCATION

AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.

Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.

(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

This MRC replaced MRC ZZZP

The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.

PDNB*APURCHASE DESCRIPTION IDENTIFICATION

THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.

Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.

(ZZZPJ81A37-30624A*)

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

MATTDMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(MATT3AEEDPCAD00*;MATT3AEEDPCAD00$DSTB000*;MATT3AEEDPCAD00$$DSTB000*)

Table 1
	ISAC Field Indicator (5000)	Location
	3AEE	OVERALL
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (MA01)	Reply
	PCAD00	PLASTIC POLYSTYRENE
	STB000	STEEL CORROSION RESISTING

SFTTDSURFACE TREATMENT

THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(SFTT3AEEDAUA000*;SFTT3AEEDAUA000$DAUA000*;SFTT3AEEDAUA000$$DAUA000*)

Table 1
	ISAC Field Indicator (5000)	Location
	3AEE	OVERALL
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (SF01)	Reply
	AUA000	GOLD

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)