An item designed to electrically connect and mechanically position the base of an item having plug-in-type contacts, and to facilitate replacement of the item accommodated. It includes sockets which accommodate the contacts of capacitors, coils, crystals, electron tubes, relays, semiconductor devices and vibrators. Excludes:sockets or receptacles designed to accommodate plug-in component circuit boards (printed circuit boards) and electronic modules or sub-assemblies. Also Excludes:heat-dissipating (not heat-sinks) sockets for mounting "power transistors".
expandFSC Information
5935Connectors, Electrical
expandColloquial Information
G5835RELAY SOCKET
G5293SOCKET,CATHODE RAY TUBE
G9304TRANSISTOR SOCKET
G5444CONNECTOR,MICROCIRCUIT
G5287SOCKET,MICROCIRCUIT
G5750VIBRATOR SOCKET
G5955ELECTRON TUBE SOCKET
G5292SOCKET,CRYSTAL UNIT
G5291SOCKET,DIODE
K1124SOCKET,DUAL IN-LINE
G7620TUBE SOCKET
G7619VALVE SOCKET (HOLDER)(BRITISH)
G1772ELECTRONIC COMPONENTS SOCKETS
G5290SOCKET,ELECTRON TUBE
G5294SOCKET,CAPACITOR
G5285SOCKET,SEMICONDUCTOR DEVICE
G4588CARRIER
G5288SOCKET,LIGHT EMITTING DIODE
J4274HOLDER,ELECTRONIC VALVE
G5445CONNECTOR,INTEGRATED CIRCUIT
G5289SOCKET,INTEGRATED CIRCUIT
G5284SOCKET,TRANSISTOR
K4965SOCKET ASSEMBLY
G5286SOCKET,RELAY
expandChange List
MRC PDNB has been added
MRC ZZZP has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED28914*)
CRPYLCONTACT POSITION ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE CONTACT POSITIONS.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CRPYL520A)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AY100861000AIRREGULAR
AY100871001AIRREGULAR
DR004201002ACIRCULAR
DR004211003ACIRCULAR
DR004221004ACIRCULAR
DR004241005ACIRCULAR
DR004251006ACIRCULAR
AY100901007ACONCENTRIC
AY100911008ATRIPLE IN LINE
AY100921009AIRREGULAR
AY100931010ATRIPLE IN LINE
DR004231011ACIRCULAR
AY100891012ATRIPLE IN LINE
AY100941013ADUAL IN-LINE
DR004261014AIN LINE
DR004271015AIN LINE
AY100961016ATRIPLE IN LINE
AY100971017ATRIPLE IN-LINE
AY100981100ACIRCULAR
AY100991101ACIRCULAR
AY101001102ACIRCULAR
AY101011103ACIRCULAR
AY101021104ACIRCULAR
AY101031105ASYMMETRICAL
AY101041106AMAGNAL
AY101051107ACONCENTRIC
AY101061108ACONCENTRIC
AY101071109AIRREGULAR
AY101081110AIRREGULAR
AY101091111AIRREGULAR
AY101101112ATRIPLE IN LINE
AY101111113AIRREGULAR
AY101121114AIRREGULAR
AY101131115AIRREGULAR
AY101141116AIRREGULAR
AY101151117AIRREGULAR
DR004281118AIN LINE
DR004291119AIN LINE
AY101171120AIRREGULAR
AY101181200ACIRCULAR
AY101191201ACIRCULAR
AY101201202AIRREGULAR
AY101221204AIRREGULAR
AY101231205ADUODECAL
DR004301206ACIRCULAR
DR004311207ACIRCULAR
DR004321208ACIRCULAR
DR004331209ACIRCULAR
DR004341210ACIRCULAR
DR004351211ACIRCULAR
DR004361212ACIRCULAR
DR004371213ACIRCULAR
AY101251215ASQUARE
AY101261216ASQUARE
AY101271217ADUAL IN-LINE
AY101281218ASYMMETRICAL
AY101291219ATRIPLE IN LINE
AY101301220ASYMMETRICAL
DR004381221AIN LINE
DR004391222AIN LINE
AY101321223AIRREGULAR
AY101331300ACIRCULAR
AY101341301ACIRCULAR
AY101351302ACONCENTRIC
AY101361303AIRREGULAR
AY101371304ACIRCULAR
AY101381305ACONCENTRIC
AY101391306AIRREGULAR
AY101401307AIRREGULAR
AY101411308AIRREGULAR
AY101421400ASYMMETRICAL
AY101431401ACONCENTRIC
AY101441402ACONCENTRIC
AY101451403ACONCENTRIC
AY101461404ASYMMETRICAL
AY101471406ACIRCULAR
AY101481407ASYMMETRICAL
AY101491408AIRREGULAR
AY101501409ACONCENTRIC
AY101511410ACONCENTRIC
AY101521411ACONCENTRIC
AY101531412ACONCENTRIC
AY101541413ADIHEPTAL
AY101551414ACONCENTRIC
AY101561415ASYMMETRICAL
AY101571416ADUAL IN-LINE
DR004401417ADUAL IN-LINE
AY101591418ASYMMETRICAL
AY101601419AIRREGULAR
AY101611420ASYMMETRICAL
AY101621421ASYMMETRICAL
AY101631422ACONCENTRIC
DR002531423ACIRCULAR
DR002541424ACIRCULAR
DR002571425ACIRCULAR
DR002591426ACIRCULAR
DR002561427ACIRCULAR
DR002581428ACIRCULAR
DR004411429ADUAL IN-LINE
AY101651430AIRREGULAR
AY101661431AIRREGULAR
AY101671432AIRREGULAR
AY101681433AIRREGULAR
AY101691434AIRREGULAR
DR004601435AIN-LINE
DR004611436AIN-LINE
AY101711437AIRREGULAR
AY101721500ASYMMETRICAL
AY101731501ASYMMETRICAL
AY101741502AIRREGULAR
AY101751503AIRREGULAR
AY101761600AIRREGULAR
AY101771601AQUADRUPLE IN LINE
AY101781602ASYMMETRICAL
AY101791603AQUADRUPLE IN LINE
AY101801604AQUADRUPLE IN-LINE
AY101811605ADUAL IN-LINE
AY102081606ASYMMETRICAL
AY102091607ASYMMETRICAL
AY102101608ASYMMETRICAL
AY102111609ASYMMETRICAL
AY102121610ADUAL IN-LINE
AY102131611ASQUARE
AY101821612AIRREGULAR
DR004621613AIN-LINE
DR004631614AIN-LINE
AY101841615AIRREGULAR
AY101851616ADUAL IN-LINE
AY101861617ASQUARE
AY101871618AQUADRUPLE IN LINE
AY101881619AQUADRUPLE IN LINE
AY101891620AQUADRUPLE IN LINE
AY101901621AQUADRUPLE IN LINE
AY101911622AIRREGULAR
AY101921700AIRREGULAR
AY101931800AIRREGULAR
AY101941801ADUAL IN-LINE
DR004821802AIN LINE DIMENSION "A" 0.100 INCH
DR004831803AIN LINE DIMENSION "A" 0.200 INCH
AY101962000ACONCENTRIC
AY101972001ACONCENTRIC
AY101982002ASYMMETRICAL
AY101992003ACONCENTRIC
AY102002004ACONCENTRIC
AY102012005ACONCENTRIC
AY102022006ACONCENTRIC
AY102032007ASYMMETRICAL
AY102042008ASYMMETRICAL
AY102052009ASYMMETRICAL
DR01562200AIN-LINE
AY102062010ACONCENTRIC
AY102072011ACIRCULAR
AY102142012AQUADRUPLE IN LINE
AY102152013AQUADRUPLE IN LINE
AY102162014ATRIPLE IN LINE
AY102172015ASYMMETRICAL
DR004842016AIN LINE
DR004852017AIN LINE
DR01564202AIN LINE
DR01567203AIN LINE
DR01568204AIN LINE
DR01569205AIN LINE
DR01573206AIN LINE
DR01574207AIN LINE
DR01575208AIN LINE
DR01576209AIN LINE
AY102192100ASYMMETRICAL
AY10597210AIN LINE
AY10598211AIN LINE
AY10599212AIN LINE
AY10600213AIN LINE
DR01559214AIN LINE
DR01560215AIN-LINE
DR01561216AIN-LINE
DR01563217AIN-LINE
DR01565218AIN-LINE
DR01566219AIN-LINE
AY102202200ACONCENTRIC
AY102212201ACIRCULAR
AY102222202AIRREGULAR
AY102232203ADUAL IN-LINE
AY102242204AIRREGULAR
AY102252205ASYMMETRICAL
AY102262300ACONCENTRIC
AY102272301AIRREGULAR
AY102282400ATRIPLE IN-LINE
DR004862401ACONCENTRIC
DR004872402ACONCENTRIC
DR005502403ADUAL IN-LINE
DR005492404ADUAL IN LINE
DR005512405ADUAL IN-LINE
DR005522406ADUAL IN-LINE
AY102312407AIRREGULAR
AY102322408AIRREGULAR
AY102332409AQUADRUPLE IN-LINE
DR005532410AIN LINE
DR005542411AIN LINE
AY102352412ASYMMETRICAL
AY102362413ASYMMETRICAL
AY102372500ACONCENTRIC
AY102382501ACONCENTRIC
AY102392503ASYMMETRICAL
AY102402504ASYMMETRICAL
AY102412600ACONCENTRIC
AY102422601ACONCENTRIC
AY102432700ACONCENTRIC
AY102442701ASYMMETRICAL
AY102452800AQUADRUPLE IN-LINE
DR005552801ADUAL IN-LINE
DR005562802ADUAL IN-LINE
DR005572803AIN LINE
DR005582804AIN LINE
AY102482805AIRREGULAR
AY102492806AIRREGULAR
AY102502807ASYMMETRICAL
AY102512900ACIRCULAR
AY102522901AIRREGULAR
AY102533000AIRREGULAR
DR01577300ACIRCULAR IRREGULAR 0.100 INCH
DR01582301ACIRCULAR IRREGULAR 0.200 INCH
DR01579302ACIRCULAR IRREGULAR 0.141 INCH
DR01578304ACIRCULAR IRREGULAR 0.115 INCH
DR01580305ACIRCULAR IRREGULAR 0.150 INCH
DR01581306ACIRCULAR IRREGULAR 0.180 INCH
DR01583307ACIRCULAR IRREGULAR 0.282 INCH
AY10602310ATRIANGULAR
AY10603311AIN LINE
AY10604312ATRIANGULAR
AY10605313AIN LINE
AY10606314AIN LINE
AY10607315ATRIANGULAR
AY10608316ATRIANGULAR
AY10609317ATRIANGULAR
AY10610318ASEMICIRCULAR
AY10611319ATRIANGULAR
AY102543200ACONCENTRIC
AY102553201AQUADRUPLE IN-LINE
DR005593202AIN-LINE
DR005603203AIN-LINE
DR005613204ADUAL IN-LINE
DR005623205ADUAL IN-LINE
AY10612320AIN LINE
AY10590321AIN LINE
AY10591322ATRIANGULAR
AY10592323AIN LINE
AY10593324ATRIANGULAR
AY10594325AIN LINE
AY10595326AIN LINE
AY10001327AIN LINE
AY10572328AIN LINE
AY10573329ATRIANGULAR
DR01442330ATRIANGULAR
DR01444331ATRIANGULAR
AY10575332AIRREGULAR
AY10576333AIN LINE
AY102583500ACONCENTRIC
AY102593600ASYMMETRICAL
AY102603601ASQUARE
AY102613602ADUAL IN-LINE
DR005633603AIN LINE
DR005643604AIN LINE
AY102633900ACONCENTRIC
AY102644000ACONCENTRIC
AY102654001AQUADRUPLE IN LINE
DR005654002ADUAL IN-LINE DIMENSION "A" 0.600 INCH
DR005664003ADUAL IN-LINE DIMENSION "A" 0.625 INCH
DR01446400ARECTANGULAR
DR01447401ARECTANGULAR
DR01448402ARECTANGULAR
DR01450403ARECTANGULAR
DR01452404ARECTANGULAR
DR01555405ARECTANGULAR
DR01556406ARECTANGULAR
DR01557407ARECTANGULAR
DR01558408ARECTANGULAR
DR01449410ARECTANGULAR
DR01451411ARECTANGULAR
AY10578412ARECTANGULAR
AY10579413ARECTANGULAR
AY10580414ADIAMOND
AY10581415ADUAL IN LINE
AY10582416ACIRCULAR
AY10583417ACIRCULAR
AY10584418ACIRCULAR
AY10585419AIRREGULAR
AY102674200AQUADRUPLE IN LINE
AY10586420AIN LINE
AY10587421AIRREGULAR
AY10588422AIRREGULAR
AY10589423ACIRCULAR
AY10002424ACIRCULAR
AY10003425AIRREGULAR
AY10004426AY
AY10005427ACIRCULAR
AY10006428ACIRCULAR
AY10007429AIRREGULAR
AY10008430AIRREGULAR
AY10009431ACONCENTRIC
DR00302432AIN LINE
DR00303433AIN LINE
AY10011434ADUAL IN-LINE
AY102684800ASYMMETRICAL
DR00304500ACIRCULAR
DR00307501ACIRCULAR
DR00308502ACIRCULAR
DR00309503ACIRCULAR
AY10013508AACORN
DR00310509ASUBMINIATURE IN LINE
AY10015510ANUVISTOR
AY10016511ANUVISTOR
AY10017512AX
AY10018513ACIRCULAR
AY10019514AX
AY10020515ACIRCULAR
AY10021516ADUAL IN LINE
AY10022517ACONCENTRIC
AY10063518ASEMICIRCULAR
AY10064519ANUVISTOR
AY10065520AACORN
AY10066521ADUAL IN LINE
AY10067522AIRREGULAR
AY10068523ACONCENTRIC
DR00311524ASUBMINIATURE IN LINE
DR00312525ASUBMINIATURE IN LINE
AY10048600ACIRCULAR
AY10049601ACONCENTRIC
AY10050602ASUBMINIATURE IN LINE
AY10051603ADUAL IN LINE
AY10052604ADUAL IN LINE
DR00317606ACIRCULAR
DR00318607ACIRCULAR
DR00319608ACIRCULAR
DR00321609ACIRCULAR
DR00322610ACIRCULAR
DR00323611ACIRCULAR
AY10053613ACIRCULAR
DR00320614ACIRCULAR
DR00324615ADUAL IN-LINE
DR00325616ADUAL IN-LINE
AY10072700AMINIATURE
AY10073701AGIANT
AY10074702ASMALL
AY10075703ACIRCULAR
AY10076704ALARGE
AY10077705AACORN
AY10078706ANUVISTOR
AY10079707ASUBMINATURE IN LINE
AY10023708ACONCENTRIC
AY10024709ACIRCULAR
AY10025710ACONCENTRIC
AY10026711ACIRCULAR
DR00313712ACIRCULAR
DR00314713ACIRCULAR
DR00315714ACIRCULAR
AY10028715ANUVISTOR
AY10029716ACIRCULAR
AY10030717ACIRCULAR
AY10031718ACIRCULAR
AY10032719ADUAL IN LINE
AY10033720AMINIATURE
DR00316721ACIRCULAR
AY102698000ADUAL IN-LINE
AY10034800ACONCENTRIC
AY10035801ATRIPLE IN LINE
AY10036802ADUAL IN LINE
AY10037803ATRIPLE IN LINE
AY10038804ASUBMINIATURE
AY10039805ALOCK-IN
DR03765806AOCTAL .687 INCH
AY10041807ASYMMETRICAL
DR03764808AOCTAL .412 INCH
AY10042809ASYMMETRICAL
AY10043810AIRREGULAR
AY10044811ASYMMETRICAL
AY10045812ACIRCULAR
AY10046813ACONCENTRIC
AY10047814ACIRCULAR
AY10054815ACIRCULAR
DR03891816ACIRCULAR .200 INCH
DR03892817ACIRCULAR .230 INCH
DR03894818ACIRCULAR .260 INCH
DR03896819ACIRCULAR .400 INCH
AY10055820ACIRCULAR
DR03890821ACIRCULAR .141 INCH
DR03893822ACIRCULAR .250 INCH
DR03895823ACIRCULAR .328 INCH
AY10056824ADUAL IN LINE
AY10057825ADUAL IN LINE
AY10059826ADUAL IN LINE
AY10060827ASYMMETRICAL
AY10061828ASYMMETRICAL
AY10062829AIRREGULAR
DR00333900ACIRCULAR
AY10081901AIRREGULAR
DR00331902ACIRCULAR
AY10082903ACIRCULAR
DR00330904ACIRCULAR
DR00332905ACIRCULAR
DR00328906ACIRCULAR
DR00326907ACIRCULAR
DR00327908ACIRCULAR
DR00329909ACIRCULAR
DR00334910AIN LINE
DR00335911AIN LINE
AY10084912ADUAL IN LINE
AY10085913AIRREGULAR
AFRLAACCOMMODATED CONTACT QUANTITY
THE NUMBER OF CONTACTS ACCOMMODATED BY THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AFRLA10*)
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJABX2*;TTQYJABX2$$JABX3*)
Table 1
Reply Code (AN89)Reply
AAAANY ACCEPTABLE
ADBCLIP
AFLCRIMP
AMEINSULATION PIERCING
AAMPIN
ACRPRINTED CIRCUIT
ABQSCREW
AHCSLEEVE
AASSOLDER STUD
AFKSOLDER WELL
ABXTAB W/SCREW
ABBTAB, SOLDER LUG
ACBTURRET
ACMWIRE HOOK
ACCWIRE LEAD
ACDWIRE LOOP
AFMWIRE WRAP
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) AEB OR AEZ WERE ENTERED FOR MRC BCNX, YOU MUST ANSWER MRC (AXGY)
BCNXDMOUNTING TYPE FOR WHICH DESIGNED
INDICATES THE TYPE OF MOUNTING FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BCNXDAXV*;BCNXDAEB$DAEZ*)
Table 1
Reply Code (AM39)Reply
AEBCHASSIS
AXVCIRCUIT BOARD
AEZPRINTED CIRCUIT
ACJTUBE
IF STYLE/REPLY CODE(s) 1B, 3B, 4B, 5B, 14B, 15B, 18B, 30B, 44B, 45B, 53B OR 56B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and AKXC and ABKW)
IF STYLE/REPLY CODE(s) 2B, 6B, 7B, 8B, 10B, 11B, 12B, 13B, 17B, 19B, 20B, 21B, 22B, 46B, 50B, 52B, 58B OR 66B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and AKXD and ABKW)
IF STYLE/REPLY CODE(s) 9B, 33B, 34B OR 43B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and AKXC and ABKW)
IF STYLE/REPLY CODE(s) 16B OR 61B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and AKXD and ABKW and ABJT)
IF STYLE/REPLY CODE(s) 23B, 24B, 27B, 28B OR 32B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and AKXD and ABKW)
IF STYLE/REPLY CODE(s) 25B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABJT and ABKW)
IF STYLE/REPLY CODE(s) 26B, 36B OR 71B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and AKXD and ABKW and ABJT)
IF STYLE/REPLY CODE(s) 29B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABPM and ABKW)
IF STYLE/REPLY CODE(s) 31B, 60B OR 68B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and ABKW and ABPM)
IF STYLE/REPLY CODE(s) 35B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABMK and AKXD and ABKW and ABJT)
IF STYLE/REPLY CODE(s) 37B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ADAT and AKXD and ABPM and ABKW and ABJT)
IF STYLE/REPLY CODE(s) 38B OR 67B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABKW)
IF STYLE/REPLY CODE(s) 39B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABPM and AKXD and ABKW)
IF STYLE/REPLY CODE(s) 40B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and ADAV and ABKW)
IF STYLE/REPLY CODE(s) 41B OR 57B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABPM and AKXC and ABKW)
IF STYLE/REPLY CODE(s) 42B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABMK and ABKW and AKXC and ABJT)
IF STYLE/REPLY CODE(s) 47B, 48B OR 49B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABMK and ADAT and AKXC and ABKW)
IF STYLE/REPLY CODE(s) 51B, 55B, 59B, 73B OR 74B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ABHP and ABMK)
IF STYLE/REPLY CODE(s) 54B, 63B, 64B, 65B OR 69B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and ABKW and ABJT)
IF STYLE/REPLY CODE(s) 62B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and AKXD and ABKW and ABHP and ABMK and ABJT)
IF STYLE/REPLY CODE(s) 70B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ABPM and AKXD)
IF STYLE/REPLY CODE(s) 72B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAV)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL6B)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AY1027910BBOTTOM MOUNT W/METAL SADDLE
AY1028011BBOTTOM MOUNT W/MOLDED SADDLE
AY1028112BBOTTOM MOUNT W/MOLDED SADDLE
AY1028213BTOP OR BOTTOM MOUNT W/MOLDED SADDLE
AY1028314BTOP MOUNT W/MOLDED SADDLE AND SHIELD BASE
AY1028415BTOP MOUNT W/THREADED SHIELD BASE AND MOLDED SADDLE
AY1028516BBOTTOM MOUNT W/MOLDED SADDLE
AY1028617BTOP OR BOTTOM MOUNT W/MOLDED SADDLE AND BUSHING
AY1028718BTOP MOUNT W/METAL MOUNTING TABS
AY1028819BTOP MOUNT W/MOLDED SADDLE
AY102701BTOP MOUNT W/METAL SADDLE
AY1028920BBOTTOM MOUNT W/MOLDED SADDLE
AY1029021BTOP MOUNT W/MOLDED SADDLE
AY1029122BTOP MOUNT W/MOLDED SADDLE
AY1029223BPCB MOUNT
AY1029324BPCB MOUNT
AY1029425BPCB MOUNT W/SHIELD BASE
AY1029526BPCB MOUNT
AY1029627BPCB MOUNT
AY1029728BPCB MOUNT
AY1029829BTOP OR BOTTOM MOUNT W/RETAINER RING
AY102712BBOTTOM MOUNT W/METAL SADDLE
AY1029930BWAFER TYPE
AY1030031BSURFACE MOUNT W/SHIELD BASE
AY1030132BTOP OR BOTTOM MOUNT
AY1030233BTOP MOUNT W/RETAINER RING GROOVE
AY1030334BTOP OR BOTTOM MOUNT W/METAL TAB
AY1030435BTOP MOUNT, PRESS FIT
AY1030536BTOP MOUNT, PRESS FIT
AY1030637BTOP MOUNT
AY1030738BTV TUBE MOUNT
AY1030839BHIGH VOLTAGE
AY102723BTOP OR BOTTOM MOUNT W/METAL SADDLE
AY1030940BTV TUBE MOUNT
AY1031041BPCB, SNAP-IN W/SHIELD BASE
AY1031142BPCB, STANDOFF TERMINALS
AY1031243BPCB SNAP IN
AY1031344BCRYSTAL, TOP OR BOTTOM MOUNT
AY1031445BCRYSTAL, BOTTOM MOUNT
AY1031546BCRYSTAL, TOP MOUNT
AY1031647BPCB MOUNT, SNAP-IN
AY1031748BPCB MOUNT, SNAP-IN
AY1031849BPCB MOUNT, SNAP-IN
AY102734BTOP MOUNT W/METAL SADDLE AND SHIELD BASE
AY1031950BPRESS FIT
AY1032051BSURFACE MOUNT
AY1032152BTOP MOUNT W/TABS
AY1032253BTOP MOUNT W/STUDS
AY1032354BPCB, STANDOFF TERMINALS
AY1032455BCRYSTAL, SURFACE MOUNT
AY1032556BTOP MOUNT W/SADDLE
AY1032657BBOTTOM MOUNT, RADIAL TERMINALS
AY1032758BBOTTOM SURFACE MOUNT
AY1032859BPCB, 90 DEG ANGLE W/O SHIELD BASE
AY102745BTOP MOUNT W/METAL SADDLE AND SHIELD BASE
AY1032960BPCB, 90 DEG ANGLE W/SHIELD BASE
AY1033061BPCB, 90 DEG ANGLE
AY1033162BPCB, 90 DEG ANGLE
AY1033263BTOP MOUNT W/HORIZONTAL CLAMP
AY1033364BTOP MOUNT W/VERTICAL CLAMP
AY1033465BTOP MOUNT W/METAL SADDLE
AY1033566BTOP MOUNT
AY1033667BTOP MOUNT
AY1033768BTOP MOUNT
AY1033869BTOP MOUNT
AY102756BTOP MOUNT W/METAL SADDLE AND TURRET EXTENSION TERMINALS
AY1033970BPCB SURFACE MOUNT
AY1034071BTOP MOUNT, BUSHING
AY1034172BCYLINDRICAL
AY1034273BRECTANGULAR
AY1034374BIRREGULAR
AY102767BTOP MOUNT W/METAL SADDLE AND BUSHINGS
AY102778BBOTTOM MOUNT W/METAL SADDLE AND BUSHINGS
AY102789BTOP MOUNT W/CENTER THRU HOLE
AFRCBCONTACT MAXIMUM CURRENT RATING IN AMPS
THE MAXIMUM CURRENT WHICH THE CONTACT MAY CONTINUOUSLY CARRY WITHOUT DEGRADATION OR DESTRUCTION,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AFRCB2.0)
AKWF*DMISSING CONTACT DESIGNATION
THE POSITION IDENTIFICATION OF MISSING CONTACT/S/.
Enter the applicable reply code from the table below
(AKWFDBF*;AKWFDAG$$DAU*)
Table 1
Reply Code (AD83)Reply
AM10TH CONTACT POSITION
AN11TH CONTACT POSITION
AP12TH CONTACT POSITION
AQ13TH CONTACT POSTION
AR14TH CONTACT POSITION
AS15TH CONTACT POSITION
AT16TH CONTACT POSITION
AU17TH CONTACT POSITION
AV18TH CONTACT POSITION
AW19TH CONTACT POSITION
AC1ST CONTACT POSITION
AX20TH CONTACT POSITION
AY21ST CONTACT POSITION
AZ22ND CONTACT POSITION
BA23RD CONTACT POSITION
BB24TH CONTACT POSITION
BC25TH CONTACT POSITION
BD26TH CONTACT POSITION
BE27TH CONTACT POSITION
BF28TH CONTACT POSITION
BG29TH CONTACT POSITION
AD2ND CONTACT POSITION
BH30TH CONTACT POSITION
BJ31ST CONTACT POSITION
BK32ND CONTACT POSITION
BL33RD CONTACT POSITION
BM34TH CONTACT POSITION
BN35TH CONTACT POSITION
BP36TH CONTACT POSITION
BQ37TH CONTACT POSITION
BR38TH CONTACT POSITION
BS39TH CONTACT POSITION
AE3RD CONTACT POSITION
BT40TH CONTACT POSITION
AF4TH CONTACT POSITION
AG5TH CONTACT POSITION
AH6TH CONTACT POSITION
AJ7TH CONTACT POSITION
AK8TH CONTACT POSITION
AL9TH CONTACT POSITION
ABALL CONTACT POSITIONS
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AASCONTACT
3AATBODY
3AEEOVERALL
3CTQSADDLE
3HOULOCATION NOT OTHERWISE SPECIFIED
3HUIBASE SHIELD
3HUJCENTER SHIELD
Table 2
Reply Code (AP33)Reply
QAEROSPACE MATERIAL SPEC STD
JAMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP18)Reply
M10TH MATERIAL RESPONSE
N11TH MATERIAL RESPONSE
P12TH MATERIAL RESPONSE
Q13TH MATERIAL RESPONSE
R14TH MATERIAL RESPONSE
S15TH MATERIAL RESPONSE
T16TH MATERIAL RESPONSE
U17TH MATERIAL RESPONSE
W18TH MATERIAL RESPONSE
X19TH MATERIAL RESPONSE
B1ST MATERIAL RESPONSE
Y20TH MATERIAL RESPONSE
Z21ST MATERIAL RESPONSE
V22ND MATERIAL RESPONSE
C2ND MATERIAL RESPONSE
D3RD MATERIAL RESPONSE
E4TH MATERIAL RESPONSE
F5TH MATERIAL RESPONSE
H6TH MATERIAL RESPONSE
J7TH MATERIAL RESPONSE
K8TH MATERIAL RESPONSE
L9TH MATERIAL RESPONSE
GALL MATERIAL RESPONSES
ASINGLE MATERIAL RESPONSE
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAC2.0*;ABPMJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKXC*JPROJECTION LENGTH BELOW MOUNTING SURFACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKXCJAC2.0*;AKXCJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKXD*JPROJECTION LENGTH ABOVE MOUNTING SURFACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKXDJAB2.0*;AKXDJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CRXR*JGROUND TERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF GROUND TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CRXRJAFM2*)
Table 1
Reply Code (AN89)Reply
AAAANY ACCEPTABLE
ADBCLIP
AFLCRIMP
AAMPIN
ACRPRINTED CIRCUIT
ABQSCREW
AHCSLEEVE
AASSOLDER STUD
AFKSOLDER WELL
ABXTAB W/SCREW
ABBTAB, SOLDER LUG
ACBTURRET
ACMWIRE HOOK
ACCWIRE LEAD
ACDWIRE LOOP
AFMWIRE WRAP
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CQRGDBODY MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BODY IS FABRICATED.
Enter the applicable reply code from the table below
(CQRGDPCG000*;CQRGDCLD000$DPCN000*;CQRGDCLD000$$DPCN000*)
Table 1
Reply Code (MA01)Reply
AL5052ALUMINUM ALLOY 5052
AL6061ALUMINUM ALLOY 6061
CLD000CERAMIC
GSA000GLASS
GSU000GLASS CLOTH
FBB000NYLON
PCG000PLASTIC DIALLYL PHTHALATE
PCN000PLASTIC PHENOLIC
PCP000PLASTIC POLYAMIDE
PCR000PLASTIC POLYCARBONATE
PCW000PLASTIC POLYESTER
AAA012THERMOPLASTIC
IF STYLE/REPLY CODE(s) ABS, ACC, ACQ, ADB, ADC, ADE OR ADF WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AEVB)
IF STYLE/REPLY CODE(s) AET OR AHF WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AEVB and THSD)
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDADE*;AXGYDADF$$DAZJ*)
Table 1
Reply Code (AM39)Reply
ADBBODY THROUGH HOLE
ABCBRACKET
AZJINSERT
ADCPRESS FIT
ABSRETAINER RING
BMSRIM MOUNTING TOE CLAMPS
ADESADDLE
BWKSLIDE TRACK
ADFSNAP-IN
ACCTAB
ACDTERMINAL
AFATHREADED BUSHING
AHFTHREADED HOLE
AETTHREADED STUD
ACQUNTHREADED HOLE
IF STYLE/REPLY CODE(s) 2D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AEJN and AKXE and ABTB) or (ADAL and AEJN and AKXE and ABTD) or (ADAL and AEJN and AKXE and THSD)
IF STYLE/REPLY CODE(s) 1D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL)
IF STYLE/REPLY CODE(s) 8D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AEJN and ABTB) or (ADAL and AEJN and THSD)
IF STYLE/REPLY CODE(s) 3D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AKXE)
IF STYLE/REPLY CODE(s) 4D, 5D OR 7D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AGVG and CSNQ)
IF STYLE/REPLY CODE(s) 6D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and CSNQ and CTCM)
IF STYLE/REPLY CODE(s) 9D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ABTD and ADAL and AEJN)
IF STYLE/REPLY CODE(s) 10D OR 16D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AEJN and ABTB) or (ADAL and AEJN and ABTD) or (ADAL and AEJN and THSD)
IF STYLE/REPLY CODE(s) 11D, 14D OR 15D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AGVA and AGVB and ABTB) or (ADAL and AGVA and AGVB and ABTD) or (ADAL and AGVA and AGVB and THSD)
IF STYLE/REPLY CODE(s) 12D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAL and AEJN and AGVD and ABTB) or (ADAL and AEJN and AGVD and ABTD) or (ADAL and AEJN and AGVD and THSD)
IF STYLE/REPLY CODE(s) 13D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAJ and ADAK and AGVA and ABTB) or (ADAJ and ADAK and AGVA and ABTD) or (ADAJ and ADAK and AGVA and THSD)
IF STYLE/REPLY CODE(s) 17D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (AEJN and ABTB) or (AEJN and ABTD) or (AEJN and THSD)
IF STYLE/REPLY CODE(s) 18D, 38D OR 39D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (AGVA and AGVB and ABTB) or (AGVA and AGVB and ABTD) or (AGVA and AGVB and THSD)
IF STYLE/REPLY CODE(s) 19D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (AGVA and AGVB and AGVD and ABTB) or (AGVA and AGVB and AGVD and ABTD) or (AGVA and AGVB and AGVD and THSD)
IF STYLE/REPLY CODE(s) 21D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (AFFL and ABTB) or (AFFL and ABTD) or (AFFL and THSD)
IF STYLE/REPLY CODE(s) 22D OR 23D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAJ and ADAK)
IF STYLE/REPLY CODE(s) 24D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ABTD and ADAJ and ADAK and AEJN)
IF STYLE/REPLY CODE(s) 25D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAK and ADAJ and ABTD and AEJN and ABKR)
IF STYLE/REPLY CODE(s) 26D, 27D, 41D OR 42D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAJ and ADAK and AEJN and ABTB) or (ADAJ and ADAK and AEJN and ABTD) or (ADAJ and ADAK and AEJN and THSD)
IF STYLE/REPLY CODE(s) 28D, 29D, 30D, 43D, 44D OR 45D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAJ and ADAK and AGVA and AGVB and ABTB) or (ADAJ and ADAK and AGVA and AGVB and ABTD) or (ADAJ and ADAK and AGVA and AGVB and THSD)
IF STYLE/REPLY CODE(s) 31D, 32D, 33D, 34D OR 35D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAJ and ADAK and AKXF and AKXG)
IF STYLE/REPLY CODE(s) 40D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ADAK and AEJN and CSWN and CTGL and ABTB) or (ADAK and AEJN and CSWN and CTGL and ABTD) or (ADAK and AEJN and CSWN and CTGL and THSD)
IF STYLE/REPLY CODE(s) 46D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ABTD and ABKR and ADAJ and ADAK and AEJN)
IF STYLE/REPLY CODE(s) 20D WERE ENTERED FOR MRC AEVB, YOU MUST ANSWER MRC (ABTB) or (ABTD) or (THSD)
AEVB*LMOUNTING HOLE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING HOLE(S).
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AEVBL38D)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AY1036810DROUND, W/ONE MOUNTING HOLE/SLOT
AY1036911DROUND, W/KEYWAY AND TWO MOUNTING HOLES/SLOTS
AY1037212DTANDEM, W/TWO MOUNTING HOLES/SLOTS
AY1037113DRECTANGULAR, W/ROUNDED ENDS AND TWO MOUN TING HOLES/SLOTS
AY1037314DROUND, W/THREE MOUNTING HOLES/SLOTS
AY1037415DROUND, W/FOUR MOUNTING HOLES/SLOTS
AY1037516DTANDEM, ROUND W/ONE MOUNTING HOLE/SLOT
AY1037617DTWO MOUNTING HOLES/SLOTS, IN-LINE
AY1037718DTWO MOUNTING HOLES/SLOTS, DIAGONAL
AY1037819DIRREGULAR
AY103591DROUND, BODY
AY1037920DSINGLE MOUNTING HOLE/SLOT
AY1038021DSLOT FOUR MOUNTING HOLES/SLOTS ON BOLT CIRCLE
AY1038122DRECTANGULAR
AY1038223DRECTANGULAR W/ROUND ENDS
AY1038324DRECTANGULAR, W/EXTERNAL SLOTS
AY1038425DRECTANGULAR, W/EXTERNAL SLOTS
AY1038526DRECTANGULAR, W/TWO MOUNTING HOLES/SLOTS
AY1038627DRECTANGULAR, W/TWO MOUNTING HOLES/SLOTS
AY1038728DRECTANGULAR, W/TWO MOUNTING HOLES/SLOTS
AY1038829DRECTANGULAR, W/FOUR MOUNTING HOLES/SLOTS
AY103602DROUND, FLATTED W/TWO MOUNTING HOLES/SLOTS
AY1038930DRECTANGULAR, W/FOUR MOUNTING HOLES/SLOTS
AY1039031DRECTANGULAR, PCB THREE NOTCH
AY1039132DRECTANGULAR, PCB FOUR NOTCH
AY1039233DRECTANGULAR, PCB FIVE NOTCH
AY1039334DRECTANGULAR, PCB SIX NOTCH
AY1039435DRECTANGULAR, PCB SEVEN NOTCH
AY1039738DFOUR MOUNTING HOLES/SLOTS
AY1039839DSIX MOUNTING HOLES/SLOTS
AY103613DROUND, FLATTED
AY1039940DRECTANGULAR, W/TWO MOUNTING HOLES/SLOTS
AY1040041DRECTANGULAR, W/TWO MOUNTING HOLES/SLOTS
AY1040142DRECTANGULAR, W/THREE MOUNTING HOLES/SLOTS
AY1040243DRECTANGULAR, W/THREE MOUNTING HOLES/SLOTS
AY1040344DRECTANGULAR, W/FOUR MOUNTING HOLES/SLOTS
AY1040445DRECTANGULAR, W/SIX MOUNTING HOLES/SLOTS
AY1040546DRECTANGULAR, W/EXTERNAL SLOTS
AY103624DROUND, W/KEYWAY
AY103635DROUND, W/KEYWAY
AY103646DROUND, W/KEY
AY103657DROUND, W/DOUBLE KEYWAY
AY103668DROUND, W/TWO MOUNTING HOLES
AY103679DROUND, W/TWO MOUNTING SLOTS
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAA2.0*;ABKRJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAA2.0*;ABTBJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAA2.0*;ABTDJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADAJ*JBODY MOUNTING HOLE ACCOMMODATION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAJJAB2.0*;ADAJJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADAK*JBODY MOUNTING HOLE ACCOMMODATION WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAKJAB2.0*;ADAKJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADAL*JBODY MOUNTING HOLE ACCOMMODATION DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADALJAB2.0*;ADALJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJNJAB2.0*;AEJNJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AFFL*JMOUNTING BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFFLJAA2.0*;AFFLJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AGVA*JCENTER TO CENTER DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGVAJAC2.0*;AGVAJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AGVB*JCENTER TO CENTER DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGVBJAA2.0*;AGVBJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AGVD*JCENTER TO CENTER DISTANCE BETWEEN INSIDE MOUNTING HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGVDJAA2.0*;AGVDJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AGVG*JBUSHING HOLE AND KEYWAY LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGVGJAB2.0*;AGVGJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKXE*JDISTANCE FROM FLATTED PORTION TO OPPOSITE SURFACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKXEJAA2.0*;AKXEJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKXF*JTERMINAL NOTCH LENGTH
NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKXFJAA2.0*;AKXFJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKXG*JTERMINAL NOTCH WIDTH
NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKXGJAB2.0*;AKXGJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CSNQ*JMOUNTING KEYWAY WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSNQJAA2.0*;CSNQJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CSWN*JSHORTEST BODY MOUNTING HOLE ACCOMMODATION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSWNJAA2.0*;CSWNJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CTCM*JMOUNTING KEYWAY LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTCMJAB2.0*;CTCMJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
CTGL*JLONGEST BODY MOUNTING HOLE ACCOMMODATION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTGLJAB2.0*;CTGLJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
IF STYLE/REPLY CODE(s) AC, AG OR AM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and AAJF)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC) or (CQJX and CQQR) or (CQJX and AAJE)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC and CQQR)
IF STYLE/REPLY CODE(s) NP OR NT WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJF)
IF STYLE/REPLY CODE(s) AZ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and CMLP)
IF STYLE/REPLY CODE(s) SA, SB OR SE WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJF)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and CMLP and AAJF)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and AAJF)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJF) or (CQJX and CQQR and AAJF)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and CMLP and AAJF) or (CQJX and AAJE and CMLP and AAJF)
IF STYLE/REPLY CODE(s) WW WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDAZ*;THSDDNT$$DSA*)
Table 1
Reply Code (AH06)Reply
AMACME
ACACME C
AGACME G
SMISO M
SSISO S
EMM
MJMJ
NPNPT
NTNPTF
AZSPECIAL ACME
SASTUB ACME
SESTUB ACME M1
SBSTUB ACME M2
UNUN
NCUNC
NEUNEF
NFUNF
NJUNJ
JCUNJC
JEUNJEF
JFUNJF
NMUNM
NSUNS
WWWHITWORTH
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAN0)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJEXT2.0*;CTTCJEXT2.0$$JEXT2.1*)
Table 1
Reply Code (AN73)Reply
EXTEXTERNAL
NTEINTERNAL
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAU1)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0*;CQQRB2.0$$BM2.0*)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*;AAJEJAM32.0/P50.0$$JA*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAL*;AAJFDAAG$$DAAL*)
Table 1
Reply Code (AA38)Reply
AAGLEFT-HAND
AALRIGHT-HAND
AKMG*JNOMINAL THREAD LENGTH
A NOMINAL MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKMGJA2.0*;AKMGJA2.0$$JA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AKWJ*LPRINTED CIRCUIT BOARD HOLE ARRANGEMENT STYLE
THE ARRANGEMENT OF HOLES IN A PRINTED CIRCUIT BOARD PROVIDED TO ACCOMMODATE TERMINALS,POLARIZATION PIN,AND/OR CENTER SHIELD.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AKWJL428E)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AY104581000ETEN HOLE
AY104591001ETEN HOLE
AY104601002ETEN HOLE
AY104611003ETEN HOLE
AY104621004ETEN HOLE
AY104631005ETEN HOLE
DR010591006ETEN HOLE DIMENSION "A" 0.200 INCH
DR010601007ETEN HOLE DIMENSION "A" 0.230 INCH
DR010651008ETEN HOLE DIMENSION "A" 0.350 INCH
DR010661009ETEN HOLE DIMENSION "A" 0.380 INCH
DR010681010ETEN HOLE DIMENSION "A" 0.420 INCH
AY104651012ETEN HOLE
DR010611013ETEN HOLE DIMENSION "A" 0.250 INCH
DR010621014ETEN HOLE DIMENSION "A" 0.273 INCH
DR010631015ETEN HOLE DIMENSION "A" 0.320 INCH
DR010641016ETEN HOLE DIMENSION "A" 0.330 INCH
DR010671017ETEN HOLE DIMENSION "A" 0.400 INCH
DR010691018ETEN HOLE DIMENSION "A" 0.430 INCH
DR010701019ETEN HOLE DIMENSION "A" 0.830 INCH
DR010711020ETEN HOLE DIMENSION "A" 0.100 INCH
DR010721021ETEN HOLE DIMENSION "A" 0.200 INCH
AY104671022ETEN HOLE
DR010731023ETEN HOLE DIMENSION "A" 0.200 INCH
DR010741024ETEN HOLE DIMENSION "A" 0.300 INCH
DR010751025ETEN HOLE DIMENSION "A" 0.450 INCH
AY104691026ETEN HOLE
AY104701027ETEN HOLE
AY104711028ETEN HOLE
AY104721100EELEVEN HOLE
AY104731101EELEVEN HOLE
AY104741102EELEVEN HOLE
DR010781103EELEVEN HOLE DIMENSION "A" 0.200 INCH
DR010791104EELEVEN HOLE DIMENSION "A" 0.230 INCH
DR010851105EELEVEN HOLE DIMENSION "A" 0.350 INCH
DR010861106EELEVEN HOLE DIMENSION "A" 0.380 INCH
DR010761107EELEVEN HOLE DIMENSION "A" 0.100 INCH
DR010771108EELEVEN HOLE DIMENSION "A" 0.200 INCH
DR010801109EELEVEN HOLE DIMENSION "A" 0.250 INCH
DR010811110EELEVEN HOLE DIMENSION "A" 0.273 INCH
DR010821111EELEVEN HOLE DIMENSION "A" 0.290 INCH
DR010831112EELEVEN HOLE DIMENSION "A" 0.320 INCH
DR010841113EELEVEN HOLE DIMENSION "A" 0.330 INCH
DR010871114EELEVEN HOLE DIMENSION "A" 0.400 INCH
DR010881115EELEVEN HOLE DIMENSION "A" 0.420 INCH
DR010891116EELEVEN HOLE DIMENSION "A" 0.430 INCH
DR010901117EELEVEN HOLE DIMENSION "A" 0.830 INCH
AY104771118EELEVEN HOLE
AY104781119EELEVEN HOLE
AY104791120EELEVEN HOLE
AY104801121EELEVEN HOLE
AY104811122EELEVEN HOLE
AY104821123EELEVEN HOLE
AY104831124EELEVEN HOLE
AY104841200ETWELVE HOLE
AY104851201ETWELVE HOLE
DR010921202ETWELVE HOLE DIMENSION "A" 0.215 INCH
DR010931203ETWELVE HOLE DIMENSION "A" 0.230 INCH
DR010981204ETWELVE HOLE DIMENSION "A" 0.365 INCH
DR010991205ETWELVE HOLE DIMENSION "A" 0.380 INCH
DR037681206EINLINE 0.100 INCH
DR037691207EINLINE 0.200 INCH
AY104871208ETWELVE HOLE
DR010911209ETWELVE HOLE DIMENSION "A" 0.200 INCH
DR010941210ETWELVE HOLE DIMENSION "A" 0.260 INCH
DR010951211ETWELVE HOLE DIMENSION "A" 0.275 INCH
DR010961212ETWELVE HOLE DIMENSION "A" 0.300 INCH
DR010971213ETWELVE HOLE DIMENSION "A" 0.350 INCH
DR011001214ETWELVE HOLE DIMENSION "A" 0.400 INCH
DR011011215ETWELVE HOLE DIMENSION "A" 0.420 INCH
DR011021216ETWELVE HOLE DIMENSION "A" 0.510 INCH
AY104891217ETWELVE HOLE
AY104901218ETWELVE HOLE
AY104911219ETWELVE HOLE
AY104921220ETWELVE HOLE
AY104931221ETWELVE HOLE
AY104941222ETWELVE HOLE
AY104951223ETWELVE HOLE
AY104961224ETWELVE HOLE
AY104971225ETWELVE HOLE
AY104981300ETHIRTEEN HOLE
AY104991301ETHIRTEEN HOLE
AY105001302ETHIRTEEN HOLE
DR018141303ETHIRTEEN HOLE
DR018151304ETHIRTEEN HOLE
DR018201305ETHIRTEEN HOLE
DR018211306ETHIRTEEN HOLE
DR018131307ETHIRTEEN HOLE
DR018161308ETHIRTEEN HOLE
DR018171309ETHIRTEEN HOLE
DR018181310ETHIRTEEN HOLE
DR018191311ETHIRTEEN HOLE
DR018221312ETHIRTEEN HOLE
DR018231313ETHIRTEEN HOLE
DR018241314ETHIRTEEN HOLE
AY105021315ETHIRTEEN HOLE
AY105031316ETHIRTEEN HOLE
AY105041317ETHIRTEEN HOLE
AY105051400EFOURTEEN HOLE
AY105061401EFOURTEEN HOLE
AY105071402EFOURTEEN HOLE
DR018251403EFOURTEEN HOLE
DR018301404EFOURTEEN HOLE
DR018341405EFOURTEEN HOLE
DR018331406EFOURTEEN HOLE
DR018351407EFOURTEEN HOLE
DR018361408EFOURTEEN HOLE
DR018261409EFOURTEEN HOLE
DR018271410EFOURTEEN HOLE
DR018281411EFOURTEEN HOLE
DR018291412EFOURTEEN HOLE
DR018311413EFOURTEEN HOLE
DR018321414EFOURTEEN HOLE
AY105101415EFOURTEEN HOLE
AY105111416EFOURTEEN HOLE
DR018371417EFOURTEEN HOLE
DR018381418EFOURTEEN HOLE
AY105131419EFOURTEEN HOLE
AY105141420EFOURTEEN HOLE
AY105151421EFOURTEEN HOLE
AY105161422EFOURTEEN HOLE
DR018391500EFIFTEEN HOLE
DR018441501EFIFTEEN HOLE
DR018401502EFIFTEEN HOLE
DR018411503EFIFTEEN HOLE
DR018421504EFIFTEEN HOLE
DR018431505EFIFTEEN HOLE
DR018451506EFIFTEEN HOLE
DR018461507EFIFTEEN HOLE
AY105181508EFIFTEEN HOLE
AY105191509EFIFTEEN HOLE
AY105201510EFIFTEEN HOLE
DR018481600ESIXTEEN HOLE 0.200 INCH
DR018491601ESIXTEEN HOLE 0.300 INCH
DR018471602ESIXTEEN HOLE 0.100 INCH
DR018501603ESIXTEEN HOLE 0.450 INCH
DR018511604ESIXTEEN HOLE 0.600 INCH
AY105221605ESIXTEEN HOLE
AY105231606ESIXTEEN HOLE
AY105241607ESIXTEEN HOLE
AY105251608ESIXTEEN HOLE
AY105261609ESIXTEEN HOLE
AY105271610ESIXTEEN HOLE
AY105281611ESIXTEEN HOLE
AY105291612ESIXTEEN HOLE
DR018521613ESIXTEEN IN-LINE HOLE
DR018531614ESIXTEEN IN-LINE HOLE
AY105311700ESEVENTEEN HOLE
AY105321800EEIGHTEEN HOLE
DR018541801EEIGHTEEN HOLE
DR018551802EEIGHTEEN HOLE
DR018561803EEIGHTEEN HOLE
DR018571804EEIGHTEEN HOLE
AY105351900ENINETEEN HOLE
AY105362000ETWENTY HOLE
DR011032001ETWENTY HOLE DIMENSION "A" 0.100 INCH
DR011042002ETWENTY HOLE DIMENSION "A" 0.200 INCH
AY105382003ETWENTY HOLE
DR00567200ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.050 INCH
DR00568201ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.075 INCH
DR00569202ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.100 INCH
DR00570203ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.115 INCH
DR00571204ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.143 INCH
DR00572205ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.192 INCH
DR00573206ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.200 INCH
DR00574207ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.238 INCH
DR00575208ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.275 INCH
DR00576209ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.430 INCH
DR00577210ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.486 INCH
DR00578211ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.500 INCH
DR00579212ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.750 INCH
DR00580213ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 0.875 INCH
DR00581214ETWO HOLE SELECT STYLE DESIGNATION BY DIMENSION "A" VALUE 2.125 INCH
AY105392200ETWENTY TWO HOLE
AY105402201ETWENTY TWO HOLE
AY105412202ETWENTY TWO HOLE
AY105422203ETWENTY TWO HOLE
AY105432204ETWENTY TWO HOLE
AY105442300ETWENTY THREE HOLE
DR011062400ETWENTY FOUR HOLE DIMENSION "A" 0.600 INCH
DR011052401ETWENTY FOUR HOLE DIMENSION "A" 0.500 INCH
DR017652402ETWENTY FOUR HOLE DIMENSION "A" 0.625 INCH
DR017662403ETWENTY FOUR HOLE DIMENSION "A" 0.750 INCH
DR017672404ETWENTY FOUR HOLE DIMENSION "A" 1.300 INCH
AY105462405ETWENTY FOUR HOLE
AY105472406ETWENTY FOUR HOLE
AY105482407ETWENTY FOUR HOLE
DR017682408ETWENTY FOUR HOLE DIMENSION "A" 0.100 INCH
DR017692409ETWENTY FOUR HOLE DIMENSION "A" 0.200 INCH
AY105502410ETWENTY FOUR HOLE
AY105512411ETWENTY FOUR HOLE
AY105522500ETWENTY FIVE HOLE
AY105532501ETWENTY FIVE HOLE
DR017702800ETWENTY EIGHT HOLE DIMENSION "A" 0.600 INCH
DR017712801ETWENTY EIGHT HOLE DIMENSION "A" 0.625 INCH
DR017222802ETWENTY EIGHT HOLE DIMENSION "A" 0.750 INCH
AY105552803ETWENTY EIGHT HOLE
DR017732804ETWENTY EIGHT HOLE DIMENSION "A" 0.100 INCH
DR017742805ETWENTY EIGHT HOLE DIMENSION "A" 0.200 INCH
AY105572806ETWENTY EIGHT HOLE
AY105582807ETWENTY EIGHT HOLE
AY105602900ETWENTY NINE HOLE
AY105593000ETHIRTY HOLE
AY10407300ETHREE HOLE
AY10408301ETHREE HOLE
DR00582302ETHREE HOLE DIMENSION "A" 0.100 INCH
DR00584303ETHREE HOLE DIMENSION "A" 0.141 INCH
DR00587304ETHREE HOLE DIMENSION "A" 0.200 INCH
DR00590305ETHREE HOLE DIMENSION "A" 0.250 INCH
DR00591306ETHREE HOLE DIMENSION "A" 0.291 INCH
DR00593307ETHREE HOLE DIMENSION "A" 0.350 INCH
DR00583308ETHREE HOLE DIMENSION "A" 0.100 INCH
DR00585309ETHREE HOLE DIMENSION "A" 0.150 INCH
DR00586310ETHREE HOLE DIMENSION "A" 0.180 INCH
DR00588311ETHREE HOLE DIMENSION "A" 0.230 INCH
DR00589312ETHREE HOLE DIMENSION "A" 0.243 INCH
DR00592313ETHREE HOLE DIMENSION "A" 0.300 INCH
DR03766314ETHREE HOLE A-0.200 B-0.220
DR03767315ETHREE HOLE A-0.190 B-0.165
AY10411316ETHREE HOLE
DR017753200ETHIRTY TWO HOLE DIMENSION "A" 0.600 INCH
DR017763201ETHIRTY TWO HOLE DIMENSION "A" 0.625 INCH
DR017773202ETHIRTY TWO HOLE DIMENSION "A" 0.750 INCH
AY105623203ETHIRTY TWO HOLE
DR014163204ETHIRTY TWO HOLE
DR014333205ETHIRTY TWO HOLE
DR014343600ETHIRTY SIX HOLE 0.600 INCH
DR014353601ETHIRTY SIX HOLE 0.625 INCH
DR014363602ETHIRTY SIX HOLE 0.750 INCH
AY105653603ETHIRTY SIX HOLE
AY105663604ETHIRTY SIX HOLE
DR014373605ETHIRTY SIX HOLE
DR014383606ETHIRTY SIX HOLE
DR014394000EFORTY HOLE
DR014404001EFORTY HOLE
DR014414002EFORTY HOLE
AY10412400EFOUR HOLE
DR00597401EFOUR HOLE DIMENSION "A" 0.200 INCH
DR00600402EFOUR HOLE DIMENSION "A" 0.250 INCH
DR00601403EFOUR HOLE DIMENSION "A" 0.291 INCH
DR00603404EFOUR HOLE DIMENSION "A" 0.350 INCH
DR00604409EFOUR HOLE DIMENSION "A" 0.100 INCH
DR00606410EFOUR HOLE DIMENSION "A" 0.141 INCH
DR00611411EFOUR HOLE DIMENSION "A" 0.250 INCH
DR00613412EFOUR HOLE DIMENSION "A" 0.291INCH
DR00614413EFOUR HOLE DIMENSION "A" 0.350 INCH
DR00594414EFOUR HOLE DIMENSION "A" 0.100 INCH
DR00595415EFOUR HOLE DIMENSION "A" 0.150 INCH
DR00596416EFOUR HOLE DIMENSION "A" 0.180 INCH
DR00598417EFOUR HOLE DIMENSION "A" 0.230 INCH
DR00599418EFOUR HOLE DIMENSION "A" 0.243 INCH
DR00602419EFOUR HOLE DIMENSION "A" 0.300 INCH
AY105694200EFORTY TWO HOLE
DR00605420EFOUR HOLE DIMENSION "A" 0.115 INCH
DR00607421EFOUR HOLE DIMENSION "A" 0.150 INCH
DR00608422EFOUR HOLE DIMENSION "A" 0.180 INCH
DR00609423EFOUR HOLE DIMENSION "A" 0.200 INCH
DR00610424EFOUR HOLE DIMENSION "A" 0.200 INCH
DR00612425EFOUR HOLE DIMENSION "A" 0.282 INCH
DR00615426EFOUR HOLE DIMENSION "A" 0.375 INCH
DR00616427EFOUR HOLE DIMENSION "A" 0.406 INCH
DR00617428EFOUR HOLE DIMENSION "A" 0.415 INCH
DR00618429EFOUR HOLE DIMENSION "A" 0.687 INCH
DR00619430EFOUR HOLE DIMENSION "A" 0.971 INCH
DR01998431EFOUR HOLE
DR01999432EFOUR HOLE
DR02000433EFOUR HOLE
DR02001434EFOUR HOLE
AY10418435EFOUR HOLE
AY105704800EFORTY EIGHT HOLE
AY10419500EFIVE HOLE
AY10420501EFIVE HOLE
DR00628502EFIVE HOLE DIMENSION "A" 0.200 INCH
DR00631503EFIVE HOLE DIMENSION "A" 0.291 INCH
DR00632504EFIVE HOLE DIMENSION "A" 0.350 INCH
DR00623505EFIVE HOLE DIMENSION "A" 0.100 INCH
DR00624506EFIVE HOLE DIMENSION "A" 0.115 INCH
DR00625507EFIVE HOLE DIMENSION "A" 0.115 INCH
DR00626508EFIVE HOLE DIMENSION "A" 0.160 INCH
DR00627509EFIVE HOLE DIMENSION "A" 0.180 INCH
DR00629510EFIVE HOLE DIMENSION "A" 0.250 INCH
DR00630511EFIVE HOLE DIMENSION "A" 0.282 INCH
DR00633512EFIVE HOLE DIMENSION "A" 0.376 INCH
DR00634513EFIVE HOLE DIMENSION "A" 0.406 INCH
DR00620514EFIVE HOLE DIMENSION "A" 0.048 INCH
DR00621515EFIVE HOLE DIMENSION "A" 1.100 INCH
DR00622516EFIVE HOLE DIMENSION "A" 0.200 INCH
AY10423517EFIVE HOLE
DR00636600ESIX HOLE DIMENSION "A" 0.141 INCH
DR00637601ESIX HOLE DIMENSION "A" 0.200 INCH
DR00641602ESIX HOLE DIMENSION "A" 0.291 INCH
DR00643603ESIX HOLE DIMENSION "A" 0.350 INCH
DR00647608ESIX HOLE DIMENSION "A" 0.141 INCH
DR00648609ESIX HOLE DIMENSION "A" 0.200 INCH
DR00653610ESIX HOLE DIMENSION "A" 0.310 INCH
DR00654611ESIX HOLE DIMENSION "A" 0.350 INCH
DR00635612ESIX HOLE 0.100 INCH
DR00638613ESIX HOLE DIMENSION "A" 0.230 INCH
DR00639614ESIX HOLE DIMENSION "A" 0.243 INCH
DR00640615ESIX HOLE DIMENSION "A" 0.250 INCH
DR00642616ESIX HOLE DIMENSION "A" 0.312 INCH
DR00644617ESIX HOLE DIMENSION "A" 0.400 INCH
DR00645618ESIX HOLE DIMENSION "A" 0.406 INCH
DR00646619ESIX HOLE DIMENSION "A" 0.100 INCH
DR00649620ESIX HOLE DIMENSION "A" 0.230 INCH
DR00650621ESIX HOLE DIMENSION "A" 0.243 INCH
DR00651622ESIX HOLE DIMENSION "A" 0.250 INCH
DR00652623ESIX HOLE DIMENSION "A" 0.291 INCH
DR00655624ESIX HOLE DIMENSION "A" 0.400INCH
DR00656625ESIX HOLE DIMENSION "A" 0.405 INCH
DR00657626ESIX HOLE DIMENSION "A" 0.300 INCH
DR00658627ESIX HOLE DIMENSION "A" 1.300 INCH
DR00659628ESIX HOLE DIMENSION "A" 0.450 INCH
AY10427700ESEVEN HOLE
DR00662701ESEVEN HOLE DIMENSION "A" 0.200 INCH
DR00666702ESEVEN HOLE DIMENSION "A" 0.291 INCH
DR00668703ESEVEN HOLE DIMENSION "A" 0.350 INCH
AY10428708ESEVEN HOLE
DR00673709ESEVEN HOLE DIMENSION "A" 0.200 INCH
DR00678710ESEVEN HOLE DIMENSION "A" 0.312 INCH
DR00679711ESEVEN HOLE DIMENSION "A" 0.350 INCH
DR00660712ESEVEN HOLE DIMENSION "A" 0.100 INCH
DR00661713ESEVEN HOLE DIMENSION "A" 0.141 INCH
DR00663714ESEVEN HOLE DIMENSION "A" 0.230 INCH
DR00664715ESEVEN HOLE DIMENSION "A" 0.243 INCH
DR00665716ESEVEN HOLE DIMENSION "A" 0.260 INCH
DR00667717ESEVEN HOLE DIMENSION "A" 0.312 INCH
DR00669718ESEVEN HOLE DIMENSION "A" 0.400 INCH
DR00670719ESEVEN HOLE DIMENSION "A" 0.406 INCH
DR00671720ESEVEN HOLE DIMENSION "A" 0.100 INCH
DR00672721ESEVEN HOLE DIMENSION "A" 0.141 INCH
DR00674722ESEVEN HOLE DIMENSION "A" 0.230 INCH
DR00675723ESEVEN HOLE DIMENSION "A" 0.243 INCH
DR00676724ESEVEN HOLE DIMENSION "A" 0.250 INCH
DR00677725ESEVEN HOLE DIMENSION "A" 0.291 INCH
DR00680726ESEVEN HOLE DIMENSION "A" 0.400 INCH
DR00681727ESEVEN HOLE DIMENSION "A" 0.406 INCH
AY10431728ESEVEN HOLE
AY10432729ESEVEN HOLE
AY10433730ESEVEN HOLE
AY105718000EEIGHTY HOLE
AY10434800EEIGHT HOLE
AY10435801EEIGHT HOLE
AY10436802EEIGHT HOLE
AY10437803EEIGHT HOLE
AY10438804EEIGHT HOLE
DR00683805EEIGHT HOLE DIMENSION "A" 0.287 DIMENSION "B" 0.740"
AY10440806EEIGHT HOLE
AY10441807EEIGHT HOLE
AY10442808EEIGHT HOLE
AY10443809EEIGHT HOLE
DR00865810EEIGHT HOLE DIMENSION "A" 0.141 INCH
DR00686811EEIGHT HOLE DIMENSION "A" 0.200 INCH
DR00693812EEIGHT HOLE DIMENSION "A" 0.310 INCH
DR00695813EEIGHT HOLE DIMENSION "A" 0.350 INCH
DR00696814EEIGHT HOLE DIMENSION "A" 0.380 INCH
DR00682815EEIGHT HOLE DIMENSION "A" 0.287 DIMENSION "B" 0.687"
DR00684816EEIGHT HOLE DIMENSION "A" 0.298 DIMENSION "B" 0.740"
AY10445817EEIGHT HOLE
AY10439818EEIGHT HOLE
AY10447819EEIGHT HOLE
DR00687820EEIGHT HOLE DIMENSION "A" 0.230 INCH
DR00688821EEIGHT HOLE DIMENSION "A" 0.243 INCH
DR00689822EEIGHT HOLE DIMENSION "A" 0.250 INCH
DR00690823EEIGHT HOLE DIMENSION "A" 0.260 INCH
DR00691824EEIGHT HOLE DIMENSION "A" 0.273 INCH
DR00692825EEIGHT HOLE DIMENSION "A" 0.291 INCH
DR00694826EEIGHT HOLE DIMENSION "A" 0.328 INCH
DR00697827EEIGHT HOLE DIMENSION "A" 0.400 INCH
DR00698828EEIGHT HOLE DIMENSION "A" 0.812 INCH
DR00699829EEIGHT HOLE DIMENSION "A" 1.125 INCH
AY10448830EEIGHT HOLE
AY10449831EEIGHT HOLE
AY10450900ENINE HOLE
AY10451901ENINE HOLE
AY10452902ENINE HOLE
AY10453903ENINE HOLE
AY10454904ENINE HOLE
DR00703905ENINE HOLE DIMENSION "A" 0.200 INCH
DR00710906ENINE HOLE DIMENSION "A" 0.310 INCH
DR00712907ENINE HOLE DIMENSION "A" 0.350 INCH
DR00700908ENINE HOLE DIMENSION "A" 0.100 INCH
DR00701909ENINE HOLE DIMENSION "A" 0.200 INCH
DR00702910ENINE HOLE DIMENSION "A" 0.141 INCH
DR00704911ENINE HOLE DIMENSION "A" 0.230 INCH
DR00705912ENINE HOLE DIMENSION "A" 0.243 INCH
DR00706913ENINE HOLE DIMENSION "A" 0.250 INCH
DR00707914ENINE HOLE DIMENSION "A" 0.260 INCH
DR00708915ENINE HOLE DIMENSION "A" 0.273 INCH
DR00709916ENINE HOLE DIMENSION "A" 0.291 INCH
DR00711917ENINE HOLE DIMENSION "A" 0.328 INCH
DR00713918ENINE HOLE DIMENSION "A" 0.380 INCH
DR00714919ENINE HOLE DIMENSION "A" 0.400 INCH
DR00715920ENINE HOLE DIMENSION "A" 0.412 INCH
DR01053921ENINE HOLE DIMENSION "A" 1.125 INCH
DR01054922ENINE HOLE DIMENSION "A" 0.390 INCH
DR01055923ENINE HOLE DIMENSION "A" 0.572 INCH
DR01056924ENINE HOLE DIMENSION "A" 0.741 INCH
DR01057925ENINE HOLE DIMENSION "A" 0.810 INCH
DR01058926ENINE HOLE DIMENSION "A" 0.836 INCH
AKWK*DCOMPONENT SHIELD MOUNTING METHOD
THE MEANS OF ATTACHING A COMPONENT SHIELD.
Enter the applicable reply code from the table below
(AKWKDADH)
Table 1
Reply Code (AM39)Reply
ADGBAYONET
ADHBEAD
AFLCLIP
ADJFORCE FIT
BMRGROOVED FINGER TYPE
ABWSCREW
AERSPRING
ACCTAB
AKWN*DPOLARIZATION TYPE
INDICATES THE TYPE OF POLARIZATION USED TO PREVENT MISMATING.
Enter the applicable reply code from the table below
(AKWNDAE*;AKWNDAD$$DAH*)
Table 1
Reply Code (AH01)Reply
ABCENTER KEY HOLE
AGCOLORED DOT
ACCONTACT POSITION
ADCONTACT SHAPE
AECONTACT SIZE
AFOFF CENTER HOLE
AAPOLARIZATION NOTCH
AHSLOT
TMQY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TMQYJAXW2*;TMQYJAXW2$$JAXW3*)
Table 1
Reply Code (AB28)Reply
ABRBOLT
ACCBRASS FERRULE
AELCAP
ASWCHIMNEY
AMNCLAMP
ASXCLIP
AKGCOVER
AASFLAPS
ACAFLAT WASHER
ACNGASKET
AAMGRIP
ADMGROMMET
ASYGROUNDING CLIP
AQYGROUNDING STRAP
ASZHIGH VOLTAGE ADAPTER
AFKHOSE COUPLING SLEEVE
ACBLOCK WASHER
BHPLOCKING LEVER
AZVLOCKWASHER
ATAMOUNTING BARS W/FELT
ABWNUT
ATBPLATE
CFRPOTTING CUP
AFFRETAINING RING
ATCRIVET
AWLRUBBER GROMMET
AMXSCREW
AFHSEAL
AXWSEALING GASKET
AXYSHIELD RING
ACXSLEEVE
ATDSPACER
ATESTANDOFF
AFNSTUD
AMEWIRE CROSSARM W/LOOP
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBFS*;CBBLDBFR$$DBFQ*)
Table 1
Reply Code (AN47)Reply
BFPCENTER SHIELD
BFQCOMPONENT EJECTION DEVICE
BFRCOMPONENT RETAINING DEVICE
BFSELECTRON TUBE SHIELD
BFTSHOCK MOUNTS
BFWZERO INSERTION FORCE CONTACTS
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDQH*;ENACDQD$DAK*;ENACDQD$$DAK*)
Table 1
Reply Code (EN02)Reply
QDHEXAVALENT CHROMIUM ALTERNATIVE
AKNON-CADMIUM PRODUCT
QHNON-LEAD ALTERNATIVE PRODUCTS
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
Table 1
Reply Code (AC28)Reply
ASPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
BSTANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
CDRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
Table 1
Reply Code (AD05)Reply
CYHARDENED
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
Table 1
Reply Code (AN58)Reply
AADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD
AFJE*GSPECIFIC EQUIPMENT ACCOMMODATED
THE NAME OF THE EQUIPMENT THE ITEM IS SPECIFICALLY DESIGNED TO ACCOMMODATE.
Enter clear text.
(AFJEGCLEARTEXT)
CSKW*JCONTACT MAXIMUM VOLTAGE IN VOLTS AND CURRENT TYPE
THE MAXIMUM POTENTIAL,EXPRESSED IN VOLTS,AND THE CURRENT TYPE THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACTS WITHOUT DAMAGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSKWJAC2.0*;CSKWJAC2.0$$JAC2.1*)
Table 1
Reply Code (AN87)Reply
ACAC
DCDC
AARN*DFABRICATION METHOD
THE PROCESS USED IN MANUFACTURING THE ITEM.
Enter the applicable reply code from the table below
(AARNDHX*;AARNDAL$DAM*)
Table 1
Reply Code (AA62)Reply
HXGLUED
ATLAMINATED
AMMOLDED
ALSTAMPED
AFDM*BCONTACT RESISTANCE IN OHMS
THE OPPOSITION TO THE FLOW OF CURRENT THROUGH MATING CONTACTS OF AN ITEM,EXPRESSED IN OHMS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AFDMB2.0)
AEZR*ARESISTOR QUANTITY
THE NUMBER OF RESISTORS INCLUDED WITH THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEZRA10*)
AGUN*JRESISTOR RATING
THE RATED OHMIC VALUE OF THE RESISTOR/S/ FURNISHED WITH THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGUNJQ2.0*;AGUNJQ2.0$$JQ2.1*)
Table 1
Reply Code (AA57)Reply
GGIGOHMS
KKILOHMS
MMEGOHMS
QOHMS
AKWT*ACAPACITOR QUANTITY
THE NUMBER OF CAPACITORS INCLUDED WITH THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AKWTA10*)
AFZH*BCAPACITANCE IN PICOFARADS
THE ELECTRICAL CAPACITANCE AS MEASURED BETWEEN TWO SPECIFIED POINTS OF THE ITEM,EXPRESSED IN PICOFARADS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AFZHB2.0*;AFZHB2.0$$BM2.0*)
AKWV*DCAPACITOR LOCATION
INDICATES THE LOCATION OF THE CAPACITOR(S) ON THE ITEM.
Enter the applicable reply code from the table below
(AKWVDAW*;AKWVDAC$$DBT*)
Table 1
Reply Code (AD83)Reply
AM10TH CONTACT POSITION
AN11TH CONTACT POSITION
AP12TH CONTACT POSITION
AQ13TH CONTACT POSTION
AR14TH CONTACT POSITION
AS15TH CONTACT POSITION
AT16TH CONTACT POSITION
AU17TH CONTACT POSITION
AV18TH CONTACT POSITION
AW19TH CONTACT POSITION
AC1ST CONTACT POSITION
AX20TH CONTACT POSITION
AY21ST CONTACT POSITION
AZ22ND CONTACT POSITION
BA23RD CONTACT POSITION
BB24TH CONTACT POSITION
BC25TH CONTACT POSITION
BD26TH CONTACT POSITION
BE27TH CONTACT POSITION
BF28TH CONTACT POSITION
BG29TH CONTACT POSITION
AD2ND CONTACT POSITION
BH30TH CONTACT POSITION
BJ31ST CONTACT POSITION
BK32ND CONTACT POSITION
BL33RD CONTACT POSITION
BM34TH CONTACT POSITION
BN35TH CONTACT POSITION
BP36TH CONTACT POSITION
BQ37TH CONTACT POSITION
BR38TH CONTACT POSITION
BS39TH CONTACT POSITION
AE3RD CONTACT POSITION
BT40TH CONTACT POSITION
AF4TH CONTACT POSITION
AG5TH CONTACT POSITION
AH6TH CONTACT POSITION
AJ7TH CONTACT POSITION
AK8TH CONTACT POSITION
AL9TH CONTACT POSITION
ABALL CONTACT POSITIONS
ABJH*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
Table 1
Reply Code (AB36)Reply
CCELSIUS
FFAHRENHEIT
AXPX*JTERMINAL INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TERMINAL,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXPXJAB2.0*;AXPXJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
Table 1
Reply Code (AN76)Reply
CCCUBIC CENTIMETERS
CFCUBIC FEET
CNCUBIC INCHES
CMCUBIC METERS
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDPTA000$DPDA000*;PRMTDPTA000$$DPDA000*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000E2.0*;PMWTJRTA000E2.0$JRTA000E2.0*;PMWTJRTA000E2.0$$JRTA000E2.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
Table 2
Reply Code (AG14)Reply
EGRAINS, TROY
RGRAMS
FOUNCES, TROY
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRHA0002.0*;PMLCJRHA0002.0$JRHA0002.0*;PMLCJRHA0002.0$$JRHA0002.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDE)
Table 1
Reply Code (AD40)Reply
DDELICATE
BEXTREMELY FRAGILE
EMODERATELY DELICATE
FMODERATELY RUGGED
GRUGGED
CVERY DELICATE
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
Table 1
Reply Code (AN62)Reply
VFEDERAL MOTOR VEHICLE SAFETY STANDARD
FFLAMMABILITY STANDARD
SGOVERNMENT SPECIFICATION
TGOVERNMENT STANDARD
UINTERNATIONAL STD/SPEC
DMANUFACTURERS SOURCE CONTROL
RMANUFACTURERS SPECIFICATION
NMANUFACTURERS SPECIFICATION CONTROL
MMANUFACTURERS STANDARD
BNATIONAL STD/SPEC
APROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
PPROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
Table 1
Reply Code (AD08)Reply
ALALLOY
BEANNEALED
ANANNEX
APAPPENDIX
ACAPPLICABILITY CLASS
ARARRANGEMENT
ASASSEMBLY
ABASSORTMENT
BFBOND
BXBOX
CYCAPACITY
CACASE
CTCATEGORY
CFCIRCUMFERENCE
CLCLASS
CECODE
CRCOLOR
CCCOMBINATION CODE
CNCOMPONENT
CPCOMPOSITION
CMCOMPOUND
CDCONDITION
AVCONFIGURATION
CSCONSTRUCTION
BGCORE CONDITION
CBCUT OFF
AMDELAY CLASS
DEDESIGN
DGDESIGNATOR
DWDRAWING NUMBER
DUDUPLEX
EGEDGE
ENEND
FYFAMILY
FGFIGURE
AKFILE NUMBER
FNFINISH
FBFLAVOR
BHFLUX PERCENTAGE
FMFORM
FAFORMULA
AJGAGE STOCK NUMBER
GRGRADE
GAGRADUATION
AXGRANULES
AYGRIT
GBGROUND
GPGROUP
HAHEAVY DUTY
BAIMAGE COLOR
NSINSERT
TMITEM
KDKIND
KTKIT
LGLENGTH
LVLEVEL
LTLIMIT
MKMARK
AAMARKER
ADMASK APERTURE
MLMATERIAL
BBMAXIMUM DENSITY
TAMEDIUM TEMPER
MHMESH
MEMETHOD
BCMINIMUM DENSITY
MDMODEL
MTMOUNTING
AQNATURAL
AUNON-DELAY CLASS
NRNUMBER
BLOUTFIT NUMBER
PAPARAGRAPH
PTPART
PNPATTERN
PCPHYSICAL CONDITION
PSPIECE
PLPLAN
PRPOINT
PDPOLISHED
PBPRESSURE RATING
QAQUALITY
QBQUENCHED
RNRANGE
AERAPID
RTRATING
RFREFERENCE NUMBER
RAREGULAR DUTY
BJRMA FLUX
SJSALIENT CHARACTERISTICS
SCSCHEDULE
SBSECTION
SLSELECTION
BDSERIALIZED
SESERIES
SVSERVICE
SXSET
SASHADE
SHSHAPE
SGSHEET
SZSIZE
AGSLOW
TCSOFT TEMPER
SKSOURCE
PZSPECIES
SQSPECIFICATION SHEET
SDSPEED
AWSTANDARD
SRSTRAIGHT
STSTYLE
SSSUBCLASS
SFSUBFORM
SPSUBTYPE
BKSUPPORT
SNSURFACE CONDITION
SYSYMBOL
SMSYSTEM
TBTABLE
TNTANNAGE
TPTEMPER
TXTEXTURE
TKTHICKNESS
TTTREATMENT
TRTRIM
TYTYPE
YNUNIT
AZUNSERIALIZED
VAVARIETY
WTWEIGHT
WDWIDTH
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AATDAL5052*;MATT3AATDAL5052$DPCP000*;MATT3AATDAL5052$$DPCP000*)
Table 1
ISAC Field Indicator (5000)Location
3AASCONTACT
3AATBODY
3AEEOVERALL
3CTQSADDLE
3HOULOCATION NOT OTHERWISE SPECIFIED
3HUIBASE SHIELD
3HUJCENTER SHIELD
Table 2
Reply Code (MA01)Reply
ALA000ALUMINUM
ALB000ALUMINUM ALLOY
AL5052ALUMINUM ALLOY 5052
AL6061ALUMINUM ALLOY 6061
ALE000ALUMINUM OXIDE
BEC000BERYLLIUM OXIDE
BRA000BRASS
CLD000CERAMIC
CUA000COPPER
CUB000COPPER ALLOY
CU0103COPPER ALLOY 510
CU0104COPPER ALLOY 511
CU0106COPPER ALLOY 524
FBA000FIBER
GSA000GLASS
GSU000GLASS CLOTH
AUA000GOLD
PBA000LEAD
AYA000MICA
NLA000NICKEL
NLB000NICKEL ALLOY
PCA000PLASTIC
PCH000PLASTIC EPOXY
PCN000PLASTIC PHENOLIC
PCP000PLASTIC POLYAMIDE
PCR000PLASTIC POLYCARBONATE
PCDM00PLASTIC POLYESTER GLASS FILLED
PCY000PLASTIC POLYETHYLENE TEREPHTHALATE
RC0020RUBBER POLYISOPRENE NATURAL CLASS NR
RCB000RUBBER SYNTHETIC
AGA000SILVER
AGF000SILVER ALLOY
STA000STEEL
SNB000TIN
ZNB000ZINC
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AASDXXB000*;SFTT3AASDXXB000$DSNB000*;SFTT3AASDXXB000$$DSNB000*)
Table 1
ISAC Field Indicator (5000)Location
3AASCONTACT
3AATBODY
3AEEOVERALL
3CTQSADDLE
3HOULOCATION NOT OTHERWISE SPECIFIED
3HUIBASE SHIELD
3HUJCENTER SHIELD
Table 2
Reply Code (SF01)Reply
CDA000CADMIUM
CMA000CHROMATE
CRA000CHROMIUM
CUA000COPPER
ENA000ENAMEL
AUA000GOLD
LQA000LACQUER
PBA000LEAD
NLA000NICKEL
NLB000NICKEL SILVER
XXB000OXIDE
PSA000PASSIVATE
RHA000RHODIUM
AGA000SILVER
SRA000SOLDER
SNA000TIN
SNB000TIN ALLOY
ZNA000ZINC
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AASCONTACT
3AATBODY
3AEEOVERALL
3CTQSADDLE
3HOULOCATION NOT OTHERWISE SPECIFIED
3HUIBASE SHIELD
3HUJCENTER SHIELD
Table 2
Reply Code (AP33)Reply
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP39)Reply
M10TH TREATMENT RESPONSE
N11TH TREATMENT RESPONSE
P12TH TREATMENT RESPONSE
Q13TH TREATMENT RESPONSE
R14TH TREATMENT RESPONSE
S15TH TREATMENT RESPONSE
B1ST TREATMENT RESPONSE
C2ND TREATMENT RESPONSE
D3RD TREATMENT RESPONSE
E4TH TREATMENT RESPONSE
F5TH TREATMENT RESPONSE
H6TH TREATMENT RESPONSE
J7TH TREATMENT RESPONSE
K8TH TREATMENT RESPONSE
L9TH TREATMENT RESPONSE
GALL TREATMENT RESPONSES
ASINGLE TREATMENT RESPONSE
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)