A straight metal rod with a shank at one end to fit the drilling machine chuck, and the opposite end externally threaded or tapered for attachment by a coupling to a threaded drill rod section. The shank has a passageway throughout its entire length for conducting air or water to clear the hole being drilled, and a packing seal in the upper end of the shank, Overall length must be less than 15 inches (381 mm).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED24414*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDFEA000*;MATTDCUB000$DALB000*;MATTDCUB000$$DALB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| A | ANY ACCEPTABLE |
| BC0015 | CARBIDE |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| FEA000 | IRON |
| STA000 | STEEL |
| STD000 | STEEL TOOL |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| B | 1ST MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) A1, A3 OR A5 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ASDB and ATCG)
IF STYLE/REPLY CODE(s) A2, A16 OR A9 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ASDB and ATCG and AAVH and ABXQ)
IF STYLE/REPLY CODE(s) A4, A6, A7, A13 OR A15 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ABMZ and ATCG)
IF STYLE/REPLY CODE(s) A10 OR A11 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ASDB)
IF STYLE/REPLY CODE(s) A14 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ABMZ and ATCG and CSKC)
IF STYLE/REPLY CODE(s) A17 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ABMZ and ATCG and AAVH and AAVK and BGMK)
IF STYLE/REPLY CODE(s) A18 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ABMZ and ATCG and BGMR)
IF STYLE/REPLY CODE(s) A19 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ASDB and ATCG and AAVH and AAVK and ABXQ)
IF STYLE/REPLY CODE(s) A20 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (ABMZ and ATCG and BGMM and BGMN and BGMS)
AAZFLSHANK STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAZFLA15)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1664 | A1 | COLLARED HEXAGON |
| AAQ1672 | A10 | PLAIN STOPPER HEXAGON |
| AAQ1673 | A11 | PLAIN STOPPER QUARTER OCTAGON |
| AAQ1674 | A13 | PARKER TAPER |
| AAQ1675 | A14 | TAPER |
| AAQ1676 | A15 | PLAIN ROUND |
| AAQ1677 | A16 | COMBINATION STRAIGHT-HEXAGON |
| AAQ1678 | A17 | DIFFERENTIAL |
| AAQ1679 | A18 | STRAIGHT ROUND-RETAINER |
| AAQ1680 | A19 | QUARTER OCTAGON |
| AAQ1665 | A2 | COMBINATION COLLARED ROUND HEXAGON |
| AAQ1681 | A20 | STRAIGHT ROUND-RETAINER |
| AAQ1666 | A3 | COLLARED QUARTER OCTAGON |
| AAQ1667 | A4 | ROUND COLLARED |
| AAQ1668 | A5 | SQUARE COLLARED |
| AAQ1669 | A6 | ROUND LUG |
| AAQ1670 | A7 | ROUND TANGENT LUGGED |
| AAQ1671 | A9 | COMBINATION ROUND-HEXAGON TANGENT LUGGED |
AAVH*JSHOULDER DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVHJAC2.0*;AAVHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVK*JSHOULDER LENGTH
THE LENGTH OF THE ENLARGED PORTION/S/ LOCATED ON THE SHANK OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVKJAC2.0*;AAVKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAC2.0*;ABMZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXQ*JFLATTED PORTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXQJAA2.0*;ABXQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAC2.0*;ASDBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ATCG*JSHANK OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHANK.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ATCGJAB2.0*;ATCGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGMK*JROUND TANG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGMKJAB2.0*;BGMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGMM*JRETAINER GROOVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGMMJAB2.0*;BGMMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGMN*JRETAINER GROOVE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGMNJAB2.0*;BGMNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGMR*JDISTANCE BETWEEN RETAINER GROOVE CENTER AND FLANGE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGMRJAB2.0*;BGMRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGMS*JDISTANCE BETWEEN SHANK END AND RETAINER GROOVE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGMSJAB2.0*;BGMSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSKC*JTAPER ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSKCJRB2.0*;CSKCJRB2.0$$JRB2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AU OR AV WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (AEAG)
IF STYLE/REPLY CODE(s) AW WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ADZY)
ABSXDATTACHMENT METHOD
THE MEANS USED TO ATTACH THE ITEM.
Enter the applicable reply code from the table below
(ABSXDAW)
| Table 1 |
| Reply Code (AB47) | Reply |
| AW | TAPERED SOCKET DRIVE |
| AU | THREADED BOTTOM DRIVE |
| AV | THREADED SHOULDER DRIVE |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
AEAG*DMANUFACTURER THREAD DESIGN DESIGNATION
THE NAME OF THE MANUFACTURER,SUPPLIER,ASSOCIATION,OR INDUSTRIAL OR GOVERNMENTAL AGENCY WHICH CONTROLS THE THREAD DESIGN,AND THE ENTITY IDENTIFYING NUMBER.
Enter the applicable reply code from the table below
(AEAGDAV)
| Table 1 |
| Reply Code (AC74) | Reply |
| AB | COROMAT ROPE |
| AN | GARDNER-DENVER CO SERIES 1000 |
| AJ | GARDNER-DENVER CO SERIES 200 |
| AK | GARDNER-DENVER CO SERIES 400 |
| AL | GARDNER-DENVER CO SERIES 600 |
| AM | GARDNER-DENVER CO SERIES 700 |
| AC | GARDNER-DENVER CO SERIES CL5-1200 |
| AD | GARDNER-DENVER CO SERIES CL5-1400 |
| AE | GARDNER-DENVER CO SERIES CL5-1600 |
| AF | GARDNER-DENVER CO SERIES CL5-1700 |
| AG | GARDNER-DENVER CO SERIES CL5-1800 |
| AH | GARDNER-DENVER CO SERIES CL5-2000 |
| AP | INGERSOL-RAND CO SERIES 113 |
| AQ | INGERSOL-RAND CO SERIES 114 |
| AS | INGERSOL-RAND CO SERIES 116 |
| AT | INGERSOL-RAND CO SERIES 119 |
| AU | INGERSOL-RAND CO SERIES 121 |
| AV | INGERSOL-RAND CO SERIES 127 |
| AW | INGERSOL-RAND CO SRI-RAL |
| AY | INGERSOL-RAND CO TYPE 1 |
| BF | INGERSOL-RAND CO TYPE 100 |
| AZ | INGERSOL-RAND CO TYPE 2 |
| BB | INGERSOL-RAND CO TYPE 22 |
| BA | INGERSOL-RAND CO TYPE 3 |
| BC | INGERSOL-RAND CO TYPE 40 |
| BD | INGERSOL-RAND CO TYPE 60 |
| BE | INGERSOL-RAND CO TYPE 70 |
| AX | INGERSOL-RAND CO TYPE S |
| AR | INGERSOL-RAND SERIES 115 |
| BR | JOY MFG CO MODEL J10 |
| BZ | JOY MFG CO MODEL J100 |
| BS | JOY MFG CO MODEL J13 |
| BT | JOY MFG CO MODEL J23 |
| BU | JOY MFG CO MODEL J30 |
| BV | JOY MFG CO MODEL J50 |
| BW | JOY MFG CO MODEL J60 |
| BX | JOY MFG CO MODEL J70 |
| BY | JOY MFG CO MODEL J75 |
| BG | JOY MFG CO MODEL JDO |
| BH | JOY MFG CO MODEL JFO |
| BJ | JOY MFG CO MODEL JHO |
| BM | JOY MFG CO MODEL JR125 |
| BN | JOY MFG CO MODEL JR150 |
| BP | JOY MFG CO MODEL JR175 |
| BQ | JOY MFG CO MODEL JR200 |
| BL | JOY MFG CO MODEL JR40 |
| BK | JOY MFG CO MODEL JSO |
| CM | MIL STD 90496 |
| CK | REVERSE BUTTRESS TYPE MIL-D-22233A |
| CN | REVERSE BUTTRESS TYPE MS39125 |
| CA | TIMKEN ROLLER BEARING CO SERIES A |
| CB | TIMKEN ROLLER BEARING CO SERIES D |
| CC | TIMKEN ROLLER BEARING CO SERIES E |
| CD | TIMKEN ROLLER BEARING CO SERIES F |
| CE | TIMKEN ROLLER BEARING CO SERIES G |
| CF | TIMKEN ROLLER BEARING CO SERIES H |
| CG | TIMKEN ROLLER BEARING CO SERIES K |
| CH | TIMKEN ROLLER BEARING CO SERIES R |
| CJ | TIMKEN ROLLER BEARING CO SERIES S |
ADZY*JNOMINAL ROD SIZE FOR WHICH DESIGNED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE ROD FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADZYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBFZ)
| Table 1 |
| Reply Code (AN47) | Reply |
| BFZ | TUNGSTEN CARBIDE INSERTS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDC)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAB2.0*;AJAFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAA2.0*;AJAGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAB2.0*;AJAHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAH*;BBRGDAN$$DAZ*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AP | CONTROLLED HUMIDITY HEATED WAREHOUSE |
| AQ | CONTROLLED HUMIDITY UNHEATED WAREHOUSE |
| AY | GENERAL PURPOSE HEATED WAREHOUSE |
| AZ | GENERAL PURPOSE UNHEATED WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AR | SHED |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ012)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ012 | COPPER |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)