A capacitor whose capacitance value is controlled by a mechanical means which effects a continuous variation of its capacitance. It includes items consisting of two or more variable capacitors which are inseparable.
ISAC Reply 3ABU added to MRC CTGN.
ISAC Reply 3AEE added to MRC CTGN.
ISAC Reply 3HOU added to MRC CTGN.
ISAC Reply 1A deleted from MRC CTGN.
ISAC Reply 1B deleted from MRC CTGN.
ISAC Reply 1C deleted from MRC CTGN.
ISAC Reply 1D deleted from MRC CTGN.
ISAC Reply 1E deleted from MRC CTGN.
ISAC Reply 1F deleted from MRC CTGN.
ISAC Reply 1G deleted from MRC CTGN.
ISAC Reply 1H deleted from MRC CTGN.
ISAC Reply 1X deleted from MRC CTGN.
ISAC Reply 1Z deleted from MRC CTGN.
ISAC Reply 3ABU added to MRC CTGP.
ISAC Reply 3AEE added to MRC CTGP.
ISAC Reply 3HOU added to MRC CTGP.
ISAC Reply 1A deleted from MRC CTGP.
ISAC Reply 1B deleted from MRC CTGP.
ISAC Reply 1C deleted from MRC CTGP.
ISAC Reply 1D deleted from MRC CTGP.
ISAC Reply 1E deleted from MRC CTGP.
ISAC Reply 1F deleted from MRC CTGP.
ISAC Reply 1G deleted from MRC CTGP.
ISAC Reply 1H deleted from MRC CTGP.
ISAC Reply 1X deleted from MRC CTGP.
ISAC Reply 1Z deleted from MRC CTGP.
ISAC Reply 3ABU added to MRC AEBC.
ISAC Reply 3AEE added to MRC AEBC.
ISAC Reply 3HOU added to MRC AEBC.
ISAC Reply 1A deleted from MRC AEBC.
ISAC Reply 1B deleted from MRC AEBC.
ISAC Reply 1C deleted from MRC AEBC.
ISAC Reply 1D deleted from MRC AEBC.
ISAC Reply 1E deleted from MRC AEBC.
ISAC Reply 1F deleted from MRC AEBC.
ISAC Reply 1G deleted from MRC AEBC.
ISAC Reply 1H deleted from MRC AEBC.
ISAC Reply 1X deleted from MRC AEBC.
ISAC Reply 1Z deleted from MRC AEBC.
ISAC Reply 3ABU added to MRC AEBD.
ISAC Reply 3AEE added to MRC AEBD.
ISAC Reply 3HOU added to MRC AEBD.
ISAC Reply 1A deleted from MRC AEBD.
ISAC Reply 1B deleted from MRC AEBD.
ISAC Reply 1C deleted from MRC AEBD.
ISAC Reply 1D deleted from MRC AEBD.
ISAC Reply 1E deleted from MRC AEBD.
ISAC Reply 1F deleted from MRC AEBD.
ISAC Reply 1G deleted from MRC AEBD.
ISAC Reply 1H deleted from MRC AEBD.
ISAC Reply 1X deleted from MRC AEBD.
ISAC Reply 1Z deleted from MRC AEBD.
ISAC Reply 3ABU added to MRC AEBF.
ISAC Reply 3AEE added to MRC AEBF.
ISAC Reply 3HOU added to MRC AEBF.
ISAC Reply 1A deleted from MRC AEBF.
ISAC Reply 1B deleted from MRC AEBF.
ISAC Reply 1C deleted from MRC AEBF.
ISAC Reply 1D deleted from MRC AEBF.
ISAC Reply 1E deleted from MRC AEBF.
ISAC Reply 1F deleted from MRC AEBF.
ISAC Reply 1G deleted from MRC AEBF.
ISAC Reply 1H deleted from MRC AEBF.
ISAC Reply 1X deleted from MRC AEBF.
ISAC Reply 1Z deleted from MRC AEBF.
ISAC Reply 3ABU added to MRC CTGQ.
ISAC Reply 3AEE added to MRC CTGQ.
ISAC Reply 3HOU added to MRC CTGQ.
ISAC Reply 1A deleted from MRC CTGQ.
ISAC Reply 1B deleted from MRC CTGQ.
ISAC Reply 1C deleted from MRC CTGQ.
ISAC Reply 1D deleted from MRC CTGQ.
ISAC Reply 1E deleted from MRC CTGQ.
ISAC Reply 1F deleted from MRC CTGQ.
ISAC Reply 1G deleted from MRC CTGQ.
ISAC Reply 1H deleted from MRC CTGQ.
ISAC Reply 1X deleted from MRC CTGQ.
ISAC Reply 1Z deleted from MRC CTGQ.
ISAC Reply 3ACB added to MRC CRSJ.
ISAC Reply 3AEE added to MRC CRSJ.
ISAC Reply 3HOU added to MRC CRSJ.
ISAC Reply 1A deleted from MRC CRSJ.
ISAC Reply 1B deleted from MRC CRSJ.
ISAC Reply 1X deleted from MRC CRSJ.
ISAC Reply 3ACB added to MRC ABWV.
ISAC Reply 3AEE added to MRC ABWV.
ISAC Reply 3HOU added to MRC ABWV.
ISAC Reply 1A deleted from MRC ABWV.
ISAC Reply 1B deleted from MRC ABWV.
ISAC Reply 1X deleted from MRC ABWV.
ISAC Reply 3ACB added to MRC ABXF.
ISAC Reply 3AEE added to MRC ABXF.
ISAC Reply 3HOU added to MRC ABXF.
ISAC Reply 1A deleted from MRC ABXF.
ISAC Reply 1B deleted from MRC ABXF.
ISAC Reply 1X deleted from MRC ABXF.
ISAC Reply 3ABU added to MRC CTGS.
ISAC Reply 3AEE added to MRC CTGS.
ISAC Reply 3HOU added to MRC CTGS.
ISAC Reply 1A deleted from MRC CTGS.
ISAC Reply 1B deleted from MRC CTGS.
ISAC Reply 1C deleted from MRC CTGS.
ISAC Reply 1D deleted from MRC CTGS.
ISAC Reply 1E deleted from MRC CTGS.
ISAC Reply 1F deleted from MRC CTGS.
ISAC Reply 1G deleted from MRC CTGS.
ISAC Reply 1H deleted from MRC CTGS.
ISAC Reply 1X deleted from MRC CTGS.
ISAC Reply 1Z deleted from MRC CTGS.
ISAC Reply 3ACC added to MRC MATT.
ISAC Reply 3ACE added to MRC MATT.
ISAC Reply 3AEE added to MRC MATT.
ISAC Reply 3HOU added to MRC MATT.
ISAC Reply 1A deleted from MRC MATT.
ISAC Reply 1B deleted from MRC MATT.
ISAC Reply 1C deleted from MRC MATT.
ISAC Reply 1D deleted from MRC MATT.
MRC AATB has been deleted
MRC ABNB has been deleted
MRC ABNC has been deleted
MRC AEDN has been deleted
MRC AEDS has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED24027*)
AFBH*AINDIVIDUAL SECTION QUANTITY
THE NUMBER OF INDIVIDUAL SECTIONS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AFBHA10*)
CTGNFCAPACITANCE RANGE IN PICOFARADS
THE MINIMUM AND MAXIMUM VALUES OF THE ELECTRICAL CAPACITANCE MEASURED BETWEEN TWO SPECIFIED POINTS ON THE ITEM,EXPRESSED IN PICOFARADS.
Enter the applicable ISAC from the table below followed by a range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(CTGN3AEEFM2.0/P4.7*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTGP*JNONDERATED VOLTAGE RATING AND TYPE
THE HIGHEST POTENTIAL AND TYPE THAT MAY BE APPLIED TO THE ITEM,AT THE HIGHEST OPERATING TEMPERATURE PERMISSIBLE WITHOUT VOLTAGE DERATING.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTGP3ABUJBD2.0*;CTGP3ABUJBD2.0$JBD2.0*;CTGP3ABUJBD2.0$$JBD2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
| Table 3 |
| Reply Code (AC81) | Reply |
| C | CONTINUOUS |
| D | DIELECTRIC WITHSTANDING |
| E | PEAK |
| J | PEAK TO PEAK |
| K | PULSE |
| H | RMS |
CQJJ*JNONDERATED OPERATING TEMP
THE TEMPERATURE/S/ AT WHICH AN ITEM CAN FUNCTION WITHOUT VOLTAGE DERATING.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJJJCB2.0*;CQJJJCB2.0$$JCB2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| B | MINIMUM |
| C | MAXIMUM |
AEBC*BTEMP COEFFICIENT OF CAPACITANCE IN PPM PER DEG CELSIUS
A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN CAPACITANCE CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(AEBC3ABUB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AEBD*FTOLERANCE OF TEMP COEFFICIENT IN PPM PER DEG CELSIUS
THE LIMITS OF PERMISSIBLE DEVIATION OF THE TEMPERATURE COEFFICIENT FROM THE RATED VALUE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable ISAC from the table below followed by a range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AEBD3AEEFM2.0/P4.7*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AEBF*FTEMP COEFFICIENT OF CAPACITANCE RANGE IN PPM PER DEG CELSIUS
THE MINIMUM AND MAXIMUM VALUES OF THE PERMISSIBLE CHANGE IN CAPACITANCE CAUSED BY A CHANGE IN TEMPERATURE,IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable ISAC from the table below followed by a range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AEBF3AEEFM2.0/P4.7*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTGQ*JCAPACITANCE CHANGE IN PERCENT AT OPERATING TEMP FROM 25 DEG CELSIUS
THE LIMITS OF CAPACITANCE CHANGE IN PERCENT AT OPERATING TEMPERATURE FROM A STATED VALUE AT 25 DEGREES CELSIUS.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CTGQ3ABUJCM32.0/P50.0*;CTGQ3ABUJCM32.0/P50.0$$JC*;CTGQ3ABUJCM32.0/P50.0$JCM32.0/P50.0*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC20) | Reply |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 40, 42, 43, 44, 45, 46, 47, 48 OR 49 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ABHP and ADAQ)
IF STYLE/REPLY CODE(s) 13, 14 OR 16 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAV)
IF STYLE/REPLY CODE(s) 15, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27 OR 28 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAV)
IF STYLE/REPLY CODE(s) 29, 31, 32, 33, 36, 37 OR 38 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAQ)
IF STYLE/REPLY CODE(s) 30 OR 34 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAT)
IF STYLE/REPLY CODE(s) 35, 39, 51, 53 OR 54 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 41 OR 50 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAU)
IF STYLE/REPLY CODE(s) 52 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ADAV)
IF STYLE/REPLY CODE(s) 55, 58, 59 OR 61 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKK and ABKW and ADAU and ADAV)
IF STYLE/REPLY CODE(s) 56 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ABPM and ADAV)
IF STYLE/REPLY CODE(s) 57 OR 60 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ADAU and ADAV)
IF STYLE/REPLY CODE(s) 62 OR 64 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and APXH)
IF STYLE/REPLY CODE(s) 63 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAV and APXH)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL23)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAK1008 | 1 | COMPRESSION |
| AAK1017 | 10 | COMPRESSION |
| AAK1018 | 11 | COMPRESSION |
| AAK1019 | 12 | DISK |
| AAK1020 | 13 | PISTON |
| AAK1021 | 14 | PISTON |
| AAK1022 | 15 | PISTON |
| AAK1023 | 16 | PISTON |
| AAK1024 | 17 | PISTON |
| AAK1025 | 18 | PISTON |
| AAK1026 | 19 | PISTON |
| AAK1009 | 2 | COMPRESSION |
| AAK1027 | 20 | PISTON |
| AAK1028 | 21 | PISTON |
| AAK1029 | 22 | PISTON |
| AAK1030 | 23 | PISTON |
| AAK1031 | 24 | PISTON |
| AAK1032 | 25 | PISTON |
| AAK1033 | 26 | PISTON |
| AAK1034 | 27 | PISTON |
| AAK1035 | 28 | PISTON |
| AAK1036 | 29 | PLATE-MESHING |
| AAK1010 | 3 | COMPRESSION |
| AAK1037 | 30 | PLATE-MESHING |
| AAK1038 | 31 | PLATE-MESHING |
| AAK1039 | 32 | PLATE-MESHING |
| AAK1040 | 33 | PLATE-MESHING |
| AAK1041 | 34 | PLATE-MESHING |
| AAK1042 | 35 | PLATE-MESHING |
| AAK1043 | 36 | PLATE-MESHING |
| AAK1044 | 37 | PLATE-MESHING |
| AAK1045 | 38 | PLATE-MESHING |
| AAK1046 | 39 | PLATE-MESHING |
| AAK1011 | 4 | COMPRESSION |
| AAK1047 | 40 | ROTARY |
| AAK1048 | 41 | ROTARY |
| AAK1049 | 42 | ROTARY |
| AAK1050 | 43 | ROTARY |
| AAK1051 | 44 | ROTARY |
| AAK1052 | 45 | ROTARY |
| AAK1053 | 46 | ROTARY |
| AAK1054 | 47 | ROTARY |
| AAK1055 | 48 | ROTARY |
| AAK1056 | 49 | ROTARY |
| AAK1012 | 5 | COMPRESSION |
| AAK1057 | 50 | ROTARY |
| AAK1058 | 51 | ROTARY |
| AAK1059 | 52 | ROTARY |
| AAK1060 | 53 | ROTARY |
| AAK1061 | 54 | ROTARY |
| AAK1062 | 55 | CONCENTRIC |
| AAK1063 | 56 | CONCENTRIC |
| AAK1064 | 57 | CONCENTRIC |
| AAK1065 | 58 | CONCENTRIC |
| AAK1066 | 59 | CONCENTRIC |
| AAK1013 | 6 | COMPRESSION |
| AAK1067 | 60 | CONCENTRIC |
| AAK1068 | 61 | CONCENTRIC |
| AAK1069 | 62 | RECTANGULAR PRISM |
| AAK1070 | 63 | CYLINDRICAL |
| AAK1071 | 64 | IRREGULAR |
| AAK1014 | 7 | COMPRESSION |
| AAK1015 | 8 | COMPRESSION |
| AAK1016 | 9 | COMPRESSION |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAC2.0*;ABKKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAA2.0*;ABPMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAA2.0*;ADAQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAA2.0*;ADAUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKNADINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAC*;AKNADAB$DAN*)
| Table 1 |
| Reply Code (AG85) | Reply |
| AC | ENCAPSULATED |
| AN | ENCASED |
| AD | HERMETICALLY SEALED |
| AB | UNINCLOSED |
IF STYLE/REPLY CODE(s) AAB, AAM OR ABB WERE ENTERED FOR MRC CTGR, YOU MUST ANSWER MRC (CRSJ)
CTGRJADJUSTMENT DEVICE DRIVE TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF DRIVE(S) PROVIDED FOR THE ADJUSTMENT DEVICE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CTGRJABD2*;CTGRJABD2$$JABD3*;CTGRJABD2$JABD2*)
| Table 1 |
| Reply Code (AE10) | Reply |
| ABB | DOUBLE ENDED SHAFT |
| AAM | GEARED SHAFT |
| AAG | HEX NUT |
| ABC | HEX NUT W/SCREWDRIVER SLOT |
| AAN | HEX SOCKET |
| AAP | KNOB |
| AAH | PLUNGER |
| ABH | PULLEY |
| ABD | ROTOR W/SCREWDRIVER SLOT |
| ABE | ROTOR W/SCREWDRIVER SLOT BOTH ENDS |
| AAB | SHAFT |
| AAF | SLOTTED SCREW |
| AAX | SQUARE HOLE |
| ABJ | THREADED HOLE |
| AAK | THUMBNUT |
| AAJ | THUMBSCREW |
| ABK | WORM GEAR |
IF STYLE/REPLY CODE(s) BM WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) BZ WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DE WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CR WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DC WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DH WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DA WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CQ WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CY WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CT WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DG WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CX WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CZ WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CP WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DF WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CS WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DD WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DJ WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) CW WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
IF STYLE/REPLY CODE(s) DB OR DK WERE ENTERED FOR MRC CRSJ, YOU MUST ANSWER MRC (ABWV)
CRSJ*DSHAFT TYPE
INDICATES THE TYPE OF SHAFT INCLUDED ON THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CRSJ3ACBDDB*;CRSJ3ACBDDB$DDA*;CRSJ3ACBDDB$$DDA*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACB | SINGLE SHAFT |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AF58) | Reply |
| BM | ROUND |
| CP | ROUND, BREAKOFF |
| CQ | ROUND, CROSS SLOTTED |
| CR | ROUND, FLAT, UNDERCUT |
| BZ | ROUND, FLATTED |
| CS | ROUND, FLATTED, THREADED HOLE |
| CT | ROUND, FLUTED |
| CW | ROUND, FLUTED, THREADED HOLE |
| CX | ROUND, HOLLOWED |
| CY | ROUND, HOLLOWED, FLATTED |
| CZ | ROUND, HOLLOWED, SLOTTED |
| DA | ROUND, MILLED, SPRING SLIT |
| DB | ROUND, NONPARALLEL FLATTED |
| DC | ROUND, PARALLEL FLATTED |
| DD | ROUND, PARALLEL FLATTED, THREADED HOLE |
| DE | ROUND, SLOTTED |
| DF | ROUND, SLOTTED, FLATTED |
| DG | ROUND, SLOTTED, PARALLEL FLATTED |
| DH | ROUND, SQUARE |
| DJ | ROUND, SQUARE, THREADED HOLE |
| DK | ROUND, V FLATTED |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
ABWV*JSHAFT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABWV3ACBJAC2.0*;ABWV3ACBJAC2.0$JAC2.0*;ABWV3ACBJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACB | SINGLE SHAFT |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXF*JSHAFT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXF3ACBJAC2.0*;ABXF3ACBJAC2.0$JAC2.0*;ABXF3ACBJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACB | SINGLE SHAFT |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXGJ*JADJUSTMENT DEVICE ROTATION
THE MEASUREMENT OF THE MECHANICAL MOTION OF THE ADJUSTMENT DEVICE.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXGJJCLBC2.0*;AXGJJCLBC2.0$JCLBC2.0*;AXGJJCLBC2.0$$JCLBC2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| CE | DEGREES |
| CL | TURNS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AC84) | Reply |
| B | CLOCKWISE |
| C | COUNTERCLOCKWISE |
AXGR*JADJUSTMENT DEVICE TORQUE
THE TORQUE REQUIRED FOR THE ADJUSTMENT DEVICE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXGRJFA2.0*;AXGRJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| F | FOOT-POUNDS |
| A | INCH-OUNCES |
| G | INCH-POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJABL2*;TTQYJABL2$$JABL3*;TTQYJABL2$JABL2*)
| Table 1 |
| Reply Code (AN89) | Reply |
| AFZ | BANANA JACK |
| AAB | BANANA PLUG |
| ABL | BINDING POST |
| AAD | BONDING PAD |
| ADB | CLIP |
| AAH | FERRULE |
| AAJ | FLANGE |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| AAR | RIBBON |
| ABQ | SCREW |
| AAS | SOLDER STUD |
| ABX | TAB W/SCREW |
| ABB | TAB, SOLDER LUG |
| ABC | THREADED HOLE |
| ABD | THREADED STUD |
| ACB | TURRET |
| ACM | WIRE HOOK |
| ACC | WIRE LEAD |
| AEG | WIRE LEAD W/LUG |
| ACD | WIRE LOOP |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
APXH*DTERMINAL LOCATION
THE POSITION OF THE TERMINAL/S/ FOR MAKING CONNECTION TO AN ITEM.PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(APXH1BDDZL*;APXH1BDDZL$$DADD*;)
| Table 1 |
| ISAC Field Indicator (0011) | Location |
| 1A | BENT BACKWARD |
| 1B | BENT FORWARD |
| 1C | PERPENDICULAR |
| Table 2 |
| Reply Code (AJ91) | Reply |
| DZB | ADJACENT SIDES |
| DZC | ADJACENT SIDES ON ADJUSTMENT CONTROL END |
| DZD | ADJACENT SIDES ON END OPPOSITE ADJUSTMENT CONTROL |
| DZE | ADJUSTMENT CONTROL END |
| DDH | CIRCUMFERENCE |
| DZH | CIRCUMFERENCE 180 DEGREES APART |
| DZJ | CIRCUMFERENCE 180 DEGREES APART ON ADJUSTMENT CONTROL END |
| DZK | CIRCUMFERENCE 180 DEGREES APART ON END OPPOSITE ADJUSTMENT CONTROL |
| DZL | CIRCUMFERENCE 90 DEGREES APART |
| DZM | CIRCUMFERENCE 90 DEGREES APART ON ADJUSTMENT CONTROL END |
| DZN | CIRCUMFERENCE 90 DEGREES APART ON END OPPOSITE ADJUSTMENT CONTROL |
| DZF | CIRCUMFERENCE ON ADJUSTMENT CONTROL END |
| DZG | CIRCUMFERENCE ON END OPPOSITE ADJUSTMENT CONTROL |
| DZP | END OPPOSITE ADJUSTMENT CONTROL |
| ADD | ONE SIDE |
| DZQ | ONE SIDE ON ADJUSTMENT CONTROL END |
| DZR | ONE SIDE ON END OPPOSITE ADJUSTMENT CONTROL |
| ANB | OPPOSITE SIDES |
| DZS | OPPOSITE SIDES ON ADJUSTMENT CONTROL END |
| DZT | OPPOSITE SIDES ON END OPPOSITE ADJUSTMENT CONTROL |
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$JAA2.0*;ABJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBT*JTERMINAL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBTJAB2.0*;AEBTJAB2.0$JAB2.0*;AEBTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWW*JTERMINAL WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TERMINAL,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWWJAA2.0*;AFWWJAA2.0$JAA2.0*;AFWWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWY*JTERMINAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TERMINAL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWYJAA2.0*;AFWYJAA2.0$JAA2.0*;AFWYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBP*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO LENGTH
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE LENGTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBPJAC2.0*;AEBPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBR*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO HEIGHT
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE HEIGHT OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBRJAC2.0*;AEBRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBS*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO DIAMETER
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE DIAMETER OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBSJAA2.0*;AEBSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AFA OR AGM WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AKEJ and AXGS)
IF STYLE/REPLY CODE(s) BKH WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AXGS)
IF STYLE/REPLY CODE(s) AET OR AHF WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AKEJ)
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AEBV)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (ABTD)
AXHRJMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJABY2*;AXHRJABY2$$JABY3*;AXHRJABY2$JABY2*)
| Table 1 |
| Reply Code (AM39) | Reply |
| ABC | BRACKET |
| BKH | BUSHING, PRESS-FIT |
| ABH | CLAMP |
| AFL | CLIP |
| ACR | FLANGE |
| AGM | LOCKING BUSHING |
| ABY | SLOT |
| ACC | TAB |
| ACD | TERMINAL |
| AFA | THREADED BUSHING |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| ACQ | UNTHREADED HOLE |
IF STYLE/REPLY CODE(s) APL OR APT WERE ENTERED FOR MRC AXGS, YOU MUST ANSWER MRC (ABKH and ABXD)
IF STYLE/REPLY CODE(s) AQM OR AQN WERE ENTERED FOR MRC AXGS, YOU MUST ANSWER MRC (ABKH and ABXD and AXHG)
AXGS*DBUSHING SHAPE
THE PHYSICAL CONFIGURATION OF THE BUSHING.
Enter the applicable reply code from the table below
(AXGSDAQM)
| Table 1 |
| Reply Code (AD07) | Reply |
| APL | ROUND |
| AQM | ROUND W/DOUBLE FLAT |
| AQN | ROUND W/FLAT |
| APT | ROUND, KEYED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABKH*JBUSHING DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUSHING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKHJAB2.0*;ABKHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXD*JBUSHING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A BUSHING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXDJAA2.0*;ABXDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXHG*JBUSHING WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXHGJAB2.0*;AXHGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CQQR) or (CQJX and CTTC) or (CQJX and AAJE)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CQQR and CTTC)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and AAJD)
IF STYLE/REPLY CODE(s) JS OR NS WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJE)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and CQQR)
AKEJ*DMOUNTING FACILITY SCREW THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE MOUNTING FACILITY.
Enter the applicable reply code from the table below
(AKEJDSM)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAK2)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJNTETEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAG6)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAC2.0*;AEBVJAC2.0$JAC2.0*;AEBVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAA2.0*;ABTDJAA2.0$JAA2.0*;ABTDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBY*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY LENGTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE LENGTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBYJAA2.0*;AEBYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEHA*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY WIDTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE WIDTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHAJAC2.0*;AEHAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBW*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBWJAA2.0*;AEBWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBX*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO DIAMETER
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE DIAMETER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBXJAB2.0*;AEBXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFFL*JMOUNTING BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFFLJAA2.0*;AFFLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC RADC, YOU MUST ANSWER MRC (RADD)
RADC*DRADIOACTIVE CONTENT
AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS.
Enter the applicable reply code from the table below
(RADCDP)
| Table 1 |
| Reply Code (AN54) | Reply |
| P | CONTAINS RADIOACTIVE MATERIAL |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDEQ)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
| EQ | NONHARDENED |
CTGS*BCAPACITANCE DRIFT IN PICOFARADS
THE DRIFT OF CAPACITANCE,EXPRESSED IN PICOFARADS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CTGS3AEEB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AXCN*DSPLIT-STATOR ROTARY PLATE TYPE
INDICATES THE TYPE OF SPLIT-STATOR ROTARY PLATE PROVIDED.
Enter the applicable reply code from the table below
(AXCNDAAD*;AXCNDAAE$DAAD*)
| Table 1 |
| Reply Code (AM16) | Reply |
| AAD | BUTTERFLY |
| AAE | DIFFERENTIAL |
AXGT*JINSULATION DC RESISTANCE AT 25 DEG CELSIUS
DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT 25 DEGREES CELSIUS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXGTJQ2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
AXGX*JINSULATION DC RESISTANCE AT MAX OPERATING TEMP
DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT THE MAXIMUM OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXGXJG2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
AECK*BDISSIPATION FACTOR AT 25 DEG CELSIUS IN PERCENT
THE RATIO OF THE RESISTANCE TO CAPACITIVE REACTANCE,EXPRESSED AT 25 DEGREES CELSIUS IN PERCENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AECKB2.0)
AECJ*BQUALITY FACTOR AT 25 DEG CELSIUS
THE RATIO OF CAPACITIVE REACTANCE TO RESISTANCE,EXPRESSED AT 25 DEGREES CELSIUS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AECJB2.0)
ATPA*APLATE QUANTITY
THE NUMBER OF PLATES INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ATPAA10*)
AXHA*JPLATE AIR GAP
THE AMOUNT OF AIR SPACE BETWEEN THE PLATES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXHAJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDALB000*;MATT3AEEDALB000$DPCH000*;MATT3AEEDALB000$$DPCH000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACC | CAPACITIVE ELECTRODE |
| 3ACE | ENCLOSURE |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| BEA000 | BERYLLIUM |
| BEB000 | BERYLLIUM COPPER (USE CUB000) |
| BRA000 | BRASS |
| BND000 | BRONZE |
| BNE000 | BRONZE PHOSPHOR |
| CLD000 | CERAMIC |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| AUA000 | GOLD |
| AUB000 | GOLD ALLOY |
| IRA000 | IRIDIUM |
| FEA000 | IRON |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| MTC000 | METAL |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| MSF000 | NONMETALLIC |
| PDA000 | PALLADIUM |
| PCA000 | PLASTIC |
| PCH000 | PLASTIC EPOXY |
| PCN000 | PLASTIC PHENOLIC |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAK00 | PLASTIC SILICONE |
| PTA000 | PLATINUM |
| PTB000 | PLATINUM ALLOY |
| SLG000 | QUARTZ |
| RHA000 | RHODIUM |
| RCE000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| AGF000 | SILVER ALLOY |
| SLF000 | STEATITE |
| STA000 | STEEL |
| TLA000 | TELLURIUM |
| SNB000 | TIN |
| SNA000 | TIN ALLOY |
| TTB000 | TITANIUM |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAN*;BBRGDAH$$DAL*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AL | TEMPERATURE CONTROLLED WAREHOUSE |
| AJ | UNHEATED WAREHOUSE |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDG)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAD*;BBRJDAB$$DAM*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AD | FLAMMABLE |
| AL | HUMIDITY CONTROLLED |
| AH | RADIOACTIVE |
| AM | SHOCK PROTECTED |
RADD*JRADIONUCLIDES DATA
THE NAME AND AMOUNT OF THE RADIONUCLIDE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(RADDJJHAAMA2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| JF | CURIES |
| JH | MICROCURIES |
| JG | MILLICURIES |
| Table 2 |
| Reply Code (AN55) | Reply |
| AAAB | ACTINIUM (89) AC-227 |
| AAAC | ACTINIUM (89) AC-228 |
| AAAD | AMERICIUM (95) AM-241 |
| AAAE | AMERICIUM (95) AM-243 |
| AAAF | ANTIMONY (51) SB-122 |
| AAAG | ANTIMONY (51) SB-124 |
| AAAH | ANTIMONY (51) SB-125 |
| AAAJ | ARGON (18) AR-37 |
| AAAK | ARGON (18) AR-41 |
| AAAL | ARGON (18) AR-41, UNCOMPRESSED |
| AAAM | ARSENIC (33) AS-73 |
| AAAN | ARSENIC (33) AS-74 |
| AAAP | ARSENIC (33) AS-76 |
| AAAQ | ARSENIC (33) AS-77 |
| AAAR | ASTATINE (85) AT-211 |
| AAAS | BARIUM (56) BA-131 |
| AAAT | BARIUM (56) BA-133 |
| AAAW | BARIUM (56) BA-140 |
| AAAX | BERKELIUM (97) BK-249 |
| AAAY | BERYLLIUM (4) BE-7 |
| AAAZ | BISMUTH (83) BI-206 |
| AABA | BISMUTH (83) BI-207 |
| AABB | BISMUTH (83) BI-210 |
| AABC | BISMUTH (83) BI-212 |
| AABD | BROMINE (35) BR-82 |
| AABE | CADMIUM (48) CD-109 |
| AABG | CADMIUM (48) CD-115 |
| AABF | CADMIUM (48) CD-115M |
| AABH | CALCIUM (20) CA-45 |
| AABJ | CALCIUM (20) CA-47 |
| AABK | CALIFORNIUM /98/ CF-249 |
| AABL | CALIFORNIUM /98/ CF-250 |
| AABM | CALIFORNIUM /98/ CF-252 |
| AABN | CARBON (6) C-14 |
| AABP | CERIUM (58) CE-141 |
| AABQ | CERIUM (58) CE-143 |
| AABR | CERIUM (58) CE-144 |
| AABS | CESIUM (55) CS-131 |
| AABW | CESIUM (55) CS-134 |
| AABT | CESIUM (55) CS-134M |
| AABX | CESIUM (55) CS-135 |
| AABY | CESIUM (55) CS-136 |
| AABZ | CESIUM (55) CS-137 |
| AACA | CHLORINE (17) CL-36 |
| AACB | CHLORINE (17) CL-38 |
| AACC | CHROMIUM (24) CR-51 |
| AACD | COBALT (27) CO-56 |
| AACE | COBALT (27) CO-57 |
| AACG | COBALT (27) CO-58 |
| AACF | COBALT (27) CO-58M |
| AACH | COBALT (27) CO-60 |
| AACJ | COPPER (29) CU-64 |
| AACK | CURIUM (96) CM-242 |
| AACL | CURIUM (96) CM-243 |
| AACM | CURIUM (96) CM-244 |
| AACN | CURIUM (96) CM-245 |
| AACP | CURIUM (96) CM-246 |
| AACQ | DYSPROSIUM (66) DY-154 |
| AACR | DYSPROSIUM (66) DY-165 |
| AACS | DYSPROSIUM (66) DY-166 |
| AACT | ERBIUM (68) ER-169 |
| AACW | ERBIUM (68) ER-171 |
| AACX | EUROPIUM (63) EU-150 |
| AACZ | EUROPIUM (63) EU-152 |
| AACY | EUROPIUM (63) EU-152M |
| AADA | EUROPIUM (63) EU-154 |
| AADB | EUROPIUM (63) EU-155 |
| AADC | FLUORINE (9) F-18 |
| AADD | GADOLINIUM (64) GD-153 |
| AADE | GADOLINIUM (64) GD-159 |
| AADF | GALLIUM (31) GA-67 |
| AADG | GALLIUM (31) GA-72 |
| AADH | GERMANIUM (32) GE-71 |
| AADJ | GOLD (79) AU-193 |
| AADK | GOLD (79) AU-194 |
| AADL | GOLD (79) AU-195 |
| AADM | GOLD (79) AU-196 |
| AADN | GOLD (79) AU-198 |
| AADP | GOLD (79) AU-199 |
| AADQ | HAFNIUM (72) HF-181 |
| AADR | HOLMIUM (67) HO-166 |
| AADS | INDIUM (49) IN-113M |
| AADT | INDIUM (49) IN-114M |
| AADX | INDIUM (49) IN-115 |
| AADW | INDIUM (49) IN-115M |
| AADY | IODINE (53) I-124 |
| AADZ | IODINE (53) I-125 |
| AAEA | IODINE (53) I-126 |
| AAEB | IODINE (53) I-129 |
| AAEC | IODINE (53) I-131 |
| AAED | IODINE (53) I-132 |
| AAEE | IODINE (53) I-133 |
| AAEF | IODINE (53) I-134 |
| AAEG | IODINE (53) I-135 |
| AAEH | IRIDIUM (77) IR-190 |
| AAEJ | IRIDIUM (77) IR-192 |
| AAEK | IRIDIUM (77) IR-194 |
| AAEL | IRON (26) FE-55 |
| AAEM | IRON (26) FE-59 |
| AAEQ | KRYPTON (36) KR-85 |
| AAER | KRYPTON (36) KR-85, UNCOMPRESSED |
| AAEN | KRYPTON (36) KR-85M |
| AAEP | KRYPTON (36) KR-85M, UNCOMPRESSED |
| AAES | KRYPTON (36) KR-87 |
| AAET | KRYPTON (36) KR-87, UNCOMPRESSED |
| AAEW | LANTHANUM (57) LA-140 |
| AAEX | LEAD (82) PB-203 |
| AAEY | LEAD (82) PB-210 |
| AAEZ | LEAD (82) PB-212 |
| AAFA | LUTECIUM (71) LU-172 |
| AAFB | LUTECIUM (71) LU-177 |
| AAFC | MAGNESIUM (12) MG-28 |
| AAFD | MANGANESE (25) MN-52 |
| AAFE | MANGANESE (25) MN-54 |
| AAFF | MANGANESE (25) MN-56 |
| AAFH | MERCURY (80) HG-197 |
| AAFG | MERCURY (80) HG-197M |
| AAFJ | MERCURY (80) HG-203 |
| AAFK | MIXED FISSION PRODUCTS MF-P |
| AAFL | MOLYBDENUM (42) MO-99 |
| AAFM | NEODYMIUM (60) ND-147 |
| AAFN | NEODYMIUM (60) ND-149 |
| AAFP | NEPTUNIUM (93) NP-237 |
| AAFQ | NEPTUNIUM (93) NP-239 |
| AAFR | NICKEL (28) NI-56 |
| AAFS | NICKEL (28) NI-59 |
| AAFT | NICKEL (28) NI-63 |
| AAFW | NICKEL (28) NI-65 |
| AAFX | NIOBIUM (41) NB-93M |
| AAFY | NIOBIUM (41) NB-95 |
| AAFZ | NIOBIUM (41) NB-97 |
| AAGA | OSMIUM (76) OS-185 |
| AAGC | OSMIUM (76) OS-191 |
| AAGB | OSMIUM (76) OS-191M |
| AAGD | OSMIUM (76) OS-193 |
| AAGE | PALLADIUM (46) PD-103 |
| AAGF | PALLADIUM (46) PD-109 |
| AAGG | PHOSPHORUS (15) P-32 |
| AAGH | PLATINUM (78) PT-191 |
| AAGJ | PLATINUM (78) PT-193 |
| AAGK | PLATINUM (78) PT-193M |
| AAGM | PLATINUM (78) PT-197 |
| AAGL | PLATINUM (78) PT-197M |
| AAGN | PLUTONIUM (94) PU-238 |
| AAGP | PLUTONIUM (94) PU-239 |
| AAGQ | PLUTONIUM (94) PU-240 |
| AAGR | PLUTONIUM (94) PU-241 |
| AAGS | PLUTONIUM (94) PU-242 |
| AAGT | POLONIUM (84) PO-210 |
| AAGW | POTASSIUM (19) K-42 |
| AAGX | POTASSIUM (19) K-43 |
| AAGY | PRASEODYMIUM (59) PR-142 |
| AAGZ | PRASEODYMIUM (59) PR-143 |
| AAHA | PROMETHIUM (61) PM-147 |
| AAHB | PROMETHIUM (61) PM-149 |
| AAHC | PROTACTINIUM (91) PA-230 |
| AAHD | PROTACTINIUM (91) PA-231 |
| AAHE | PROTACTINIUM (91) PA-233 |
| AAHF | RADIUM (88) RA-223 |
| AAHG | RADIUM (88) RA-224 |
| AAHH | RADIUM (88) RA-226 |
| AAHJ | RADIUM (88) RA-228 |
| AAHK | RADON (86) RN-220 |
| AAHL | RADON (86) RN-222 |
| AAHM | RHENIUM (75) RE-183 |
| AAHN | RHENIUM (75) RE-186 |
| AAHP | RHENIUM (75) RE-187 |
| AAHQ | RHENIUM (75) RE-188 |
| AAHR | RHENIUM (75) RE-NATURAL |
| AAHS | RHODIUM (45) RH-103M |
| AAHT | RHODIUM (45) RH-105 |
| AAHW | RUBIDIUM (37) RB-86 |
| AAHX | RUBIDIUM (37) RB-87 |
| AAHY | RUBIDIUM (37) RB-NATURAL |
| AAJA | RUTHENIUM (44) RU-103 |
| AAJB | RUTHENIUM (44) RU-105 |
| AAJC | RUTHENIUM (44) RU-106 |
| AAHZ | RUTHENIUM (44) RU-97 |
| AAJD | SAMARIUM (62) SM-145 |
| AAJE | SAMARIUM (62) SM-147 |
| AAJF | SAMARIUM (62) SM-151 |
| AAJG | SAMARIUM (62) SM-153 |
| AAJH | SCANDIUM (21) SC-46 |
| AAJJ | SCANDIUM (21) SC-47 |
| AAJK | SCANDIUM (21) SC-48 |
| AAJL | SELENIUM (34) SE-75 |
| AAJM | SILICON (14) SI-31 |
| AAJN | SILVER (47) AG-105 |
| AAJP | SILVER (47) AG-110M |
| AAJQ | SILVER (47) AG-111 |
| AAJR | SODIUM (11) NA-22 |
| AAJS | SODIUM (11) NA-24 |
| AAJW | STRONTIUM (38) SR-85 |
| AAJT | STRONTIUM (38) SR-85M |
| AAJX | STRONTIUM (38) SR-89 |
| AAJY | STRONTIUM (38) SR-90 |
| AAJZ | STRONTIUM (38) SR-91 |
| AAKA | STRONTIUM (38) SR-92 |
| AAKB | SULPHUR (16) S-35 |
| AAKC | TANTALUM (73) TA-182 |
| AAKE | TECHNETIUM (43) TC-96 |
| AAKD | TECHNETIUM (43) TC-96M |
| AAKG | TECHNETIUM (43) TC-97 |
| AAKF | TECHNETIUM (43) TC-97M |
| AAKJ | TECHNETIUM (43) TC-99 |
| AAKH | TECHNETIUM (43) TC-99M |
| AAKK | TELLURIUM (52) TE-125M |
| AAKM | TELLURIUM (52) TE-127 |
| AAKL | TELLURIUM (52) TE-127M |
| AAKP | TELLURIUM (52) TE-129 |
| AAKN | TELLURIUM (52) TE-129M |
| AAKQ | TELLURIUM (52) TE-131M |
| AAKR | TELLURIUM (52) TE-132 |
| AAKS | TERBIUM (65) TB-160 |
| AAKT | THALLIUM (81) TL-200 |
| AAKW | THALLIUM (81) TL-201 |
| AAKX | THALLIUM (81) TL-202 |
| AAKY | THALLIUM (81) TL-204 |
| AAKZ | THORIUM (90) TH-227 |
| AALA | THORIUM (90) TH-228 |
| AALB | THORIUM (90) TH-230 |
| AALC | THORIUM (90) TH-231 |
| AALD | THORIUM (90) TH-232 |
| AALE | THORIUM (90) TH-234 |
| AALF | THORIUM (90) TH-NATURAL |
| AALG | THULIUM (69) TM-168 |
| AALH | THULIUM (69) TM-170 |
| AALJ | THULIUM (69) TM-171 |
| AALK | TIN (50) SN-113 |
| AALL | TIN (50) SN-117M |
| AALM | TIN (50) SN-121 |
| AALN | TIN (50) SN-125 |
| AALP | TRITIUM (1) H-3 |
| AALQ | TRITIUM (1) H-3 AS GAS, LUMINOUS PAINT, OR ADSORBED ON SOLID MATERIAL |
| AALR | TUNGSTEN (74) W-181 |
| AALS | TUNGSTEN (74) W-185 |
| AALT | TUNGSTEN (74) W-187 |
| AALW | URANIUM (92) U-230 |
| AALX | URANIUM (92) U-232 |
| AALY | URANIUM (92) U-233 |
| AALZ | URANIUM (92) U-234 |
| AAMA | URANIUM (92) U-235 |
| AAMB | URANIUM (92) U-236 |
| AAMC | URANIUM (92) U-238 |
| AAMF | URANIUM (92) U-DEPLETED |
| AAME | URANIUM (92) U-ENRICHED |
| AAMD | URANIUM (92) U-NATURAL |
| AAMG | VANADIUM (23) V-48 |
| AAMH | VANADIUM (23) V-49 |
| AAMJ | XENON (54) XE-125 |
| AAMK | XENON (54) XE-131M |
| AAML | XENON (54) XE-131M, UNCOMPRESSED |
| AAMM | XENON (54) XE-133 |
| AAMN | XENON (54) XE-133, UNCOMPRESSED |
| AAMP | XENON (54) XE-135 |
| AAMQ | XENON (54) XE-135, UNCOMPRESSED |
| AAMR | YTTERBIUM (70) YB-175 |
| AAMS | YTTRIUM (39) Y-88 |
| AAMT | YTTRIUM (39) Y-90 |
| AAMX | YTTRIUM (39) Y-91 |
| AAMW | YTTRIUM (39) Y-91M |
| AAMY | YTTRIUM (39) Y-92 |
| AAMZ | YTTRIUM (39) Y-93 |
| AANA | ZINC (30) ZN-65 |
| AANC | ZINC (30) ZN-69 |
| AANB | ZINC (30) ZN-69M |
| AAND | ZIRCONIUM (40) ZR-93 |
| AANE | ZIRCONIUM (40) ZR-95 |
| AANF | ZIRCONIUM (40) ZR-97 |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDAZA000$DPDA000*;PRMTDAZA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000F2.0*;PMWTJPDA000F2.0$JPDA000F2.0*;PMWTJPDA000F2.0$$JPDA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRHA0002.0*;PMLCJRHA0002.0$JRHA0002.0*;PMLCJRHA0002.0$$JRHA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ012*;HZRDDHAZ092$$DHAZ030*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ012 | COPPER |
| HAZ092 | MAGNESIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ052 | ZINC |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)