A crane complete with crane boom and attachments mounted on a wheeled carriage chassis which may derive its mobile power from the crane power unit or from an independent power unit. Not convertible to shovel front, backhoe, or skimmer operations. Excludes:truck mounted cranes, cranes mounted on a wheeled tractor, and warehouse crane trucks.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED22759*)
CGTXJMAXIMUM LIFTING CAPACITY
THE MAXIMUM WEIGHT THAT THE ITEM IS DESIGNED TO LIFT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CGTXJBX2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BX | METRIC TONS |
| BY | TONS |
CGTYJBOOM LENGTH AT WHICH LIFTING CAPACITY IS RATED
A MEASUREMENT OF THE BOOM LENGTH AT WHICH THE LIFTING CAPACITY IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CGTYJFC2.0*;CGTYJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CGTZJBOOM RADIUS AT WHICH LIFTING CAPACITY IS RATED
A MEASUREMENT OF THE BOOM RADIUS AT WHICH THE LIFTING CAPACITY IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CGTZJFA2.0*;CGTZJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CGWBDOUTRIGGER POSITION AT WHICH LIFTING CAPACITY IS RATED
AN INDICATION OF THE OUTRIGGER POSITION AT WHICH THE LIFTING CAPACITY IS RATED.
Enter the applicable reply code from the table below
(CGWBDJ*;CGWBDH$DJ*)
| Table 1 |
| Reply Code (AB00) | Reply |
| J | NOT SET |
| H | SET |
CMMJDOPERATING POWER TYPE
INDICATES THE TYPE OF POWER USED TO OPERATE THE ITEM.
Enter the applicable reply code from the table below
(CMMJDFB*;CMMJDCB$DFA*;CMMJDCB$$DFA*)
| Table 1 |
| Reply Code (AH83) | Reply |
| A | ANY ACCEPTABLE |
| EC | ELECTRIC |
| FB | ELECTROHYDRAULIC |
| BZ | ELECTROMECHANICAL |
| FA | HYDRAULIC |
| CB | MECHANICAL |
IF YOU ANSWER MRC CGWD, YOU MUST ANSWER MRC (NMBR and AQGA and AQGB)
CGWD*DCRANE ENGINE TYPE
INDICATES THE TYPE OF CRANE ENGINE PROVIDED.
Enter the applicable reply code from the table below
(CGWDDDP*;CGWDDCH$DAF*;CGWDDCH$$DAF*)
| Table 1 |
| Reply Code (AG27) | Reply |
| DP | DIESEL |
| AF | GAS TURBINE |
| CH | GASOLINE |
NMBR*AQUANTITY
A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.
Enter the numeric reply with a minimum of one digit.
(NMBRA10*)
AQGA*GMANUFACTURER NAME
THE NAME OF THE MANUFACTURER.
Enter clear text.
(AQGAGCLEARTEXT)
AQGB*AMANUFACTURER IDENTIFYING NUMBER
THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(AQGBAG0)
IF STYLE/REPLY CODE(s) AC, AE OR AF WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AYMY and ATJL and AYHQ)
AKDJ*DPRIME MOVER TYPE
INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT.
Enter the applicable reply code from the table below
(AKDJDAC*;AKDJDAF$DA*)
| Table 1 |
| Reply Code (AG27) | Reply |
| A | ANY ACCEPTABLE |
| AC | DIESEL ENGINE |
| AF | GAS TURBINE |
| AE | GASOLINE ENGINE |
AYMY*AENGINE QUANTITY
THE NUMBER OF ENGINES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AYMYA10*)
ATJL*GENGINE MANUFACTURER NAME
THE NAME OF THE MANUFACTURER OF THE ENGINE FURNISHED.
Enter clear text.
(ATJLGCLEARTEXT)
AYHQ*GENGINE MANUFACTURER IDENTIFYING NUMBER
THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE ENGINE.
Enter clear text.
(AYHQGCLEARTEXT)
BKXMADRUM QUANTITY
THE NUMBER OF DRUMS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BKXMA10*)
CGWFJBOOM OVERALL LENGTH
THE LONGEST DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BOOM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CGWFJFC2.0*;CGWFJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASZHDBOOM DESIGN
THE DESIGN OF THE BOOM.
Enter the applicable reply code from the table below
(ASZHDAY*;ASZHDAD$DAD*)
| Table 1 |
| Reply Code (AH47) | Reply |
| AY | NONTELESCOPING |
| AD | TELESCOPING |
CGWGBBOOM MAXIMUM ANGLE IN DEG
THE MAXIMUM BOOM ANGLE,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CGWGB2.0)
IF STYLE/REPLY CODE(s) C WERE ENTERED FOR MRC CGWH, YOU MUST ANSWER MRC (CGWJ)
CGWHDBOOM CONTINUOUS ROTATION FEATURE
AN INDICATION OF WHETHER OR NOT A FEATURE THAT PERMITS CONTINUOUS ROTATION OF THE BOOM IS INCLUDED.
Enter the applicable reply code from the table below
(CGWHDC*;CGWHDB$DB*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
CGWJ*BBOOM MAXIMUM ROTATION IN DEG
THE MAXIMUM BOOM ROTATION,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CGWJB2.0)
CGWK*DBOOM EXTENSION TYPE
INDICATES THE TYPE OF BOOM EXTENSION PROVIDED.
Enter the applicable reply code from the table below
(CGWKDBPD*;CGWKDBPF$DBPE*;CGWKDBPF$$DBPE*)
| Table 1 |
| Reply Code (AK95) | Reply |
| A | ANY ACCEPTABLE |
| BPD | GOOSENECK |
| BPE | MIDDLE BOOM |
| CBA | STRAIGHT 3 SECTION |
| BPF | STRAIGHT JIB |
| BPG | TELESCOPIC |
AZBTLWHEEL ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE WHEEL(S).
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AZBTL15)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAG1531 | 1 | SINGLE WHEELS, SINGLE AXLE AT CENTER |
| AAG1540 | 10 | SINGLE WHEELS, SINGLE AXLES, ONE EACH EN D AND CENTER |
| AAG1541 | 11 | SINGLE WHEELS, TANDEM IN-LINE AXLES, LOW BOY TYPE ONE END |
| AAG1542 | 12 | DUAL WHEELS, SINGLE AXLE AT CENTER |
| AAG1543 | 13 | DUAL WHEELS, SINGLE AXLE, OFF CENTER |
| AAG1544 | 14 | DUAL WHEELS, SINGLE AXLE ONE END |
| AAG1545 | 15 | DUAL WHEELS, TANDEM SINGLE AXLES, ONE EN D |
| AAG1546 | 16 | DUAL WHEELS, TANDEM SINGLE AXLES ATCENTE R |
| AAG1547 | 17 | DUAL WHEELS, SINGLE AXLE AT EACH END |
| AAG1548 | 18 | DUAL WHEELS, IN-LINE SINGLE AXLES, LOW B OY TYPE ONE END |
| AAG1549 | 19 | DUAL WHEELS, TRIPLE SINGLE AXLES ONE END |
| AAG1532 | 2 | SINGLE WHEELS SINGLE AXLE OFF CENTER |
| AAG1550 | 20 | DUAL WHEELS, SINGLE AXLES, ONE EACH ENDAND CENTER |
| AAG1551 | 21 | DUAL WHEELS, TANDEM IN-LINE AXLES, LOW B OY TYPE ONE END |
| AAG1552 | 22 | DUAL WHEELS, IN-LINE SINGLE AXLES, LOWBO Y TYPE ONE END, DUAL WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1553 | 23 | DUAL WHEELS, TANDEM IN-LINE AXLES, LOWBO Y TYPE ONE END, DUAL WHEELS, IN-LINE SINGLE AXLES LOWBOY TYPE OPPOSITE END |
| AAG1554 | 24 | DUAL WHEELS, SINGLE AXLE ONE END, SINGLEWHEELS, SINGLE AXLE, DOLLY TYPE OPPOSITE END |
| AAG1555 | 25 | DUAL WHEELS, SINGLE AXLE ONE END, SINGLEWHEELS, SINGLE AXLE OPPOSITE END |
| AAG1556 | 26 | DUAL WHEELS, TANDEM SINGLE AXLES ONE END , SINGLE WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1557 | 27 | DUAL WHEELS, TANDEM SINGLE AXLES ONE END , DUAL WHEELS SINGLE AXLE, OPPOSITE END |
| AAG1558 | 28 | DUAL WHEELS, TANDEM SINGLE AXLES, EACH E ND |
| AAG1559 | 29 | SINGLE WHEEL, TANDEM SINGLE AXLES, EACHEND |
| AAG1533 | 3 | SINGLE WHEELS, SINGLE AXLE AT END |
| AAG1560 | 30 | DUAL WHEELS, TANDEM SINGLE AXLES ONE END , SINGLE WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1561 | 31 | SINGLE WHEELS, TRIPLE SINGLE AXLES ONE E ND, SINGLE WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1562 | 32 | SINGLE WHEELS, TRIPLE SINGLE AXLES ONE E ND, SINGLE WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1563 | 33 | SINGLE WHEELS, TANDEM IN-LINE SINGLE AXL ES, LOWBOY TYPE ONE END, SINGLE WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1564 | 34 | SINGLE WHEELS, TANDEM IN-LINE SINGLE AXL ES LOWBOY TYPE ONE END, SINGLE WHEELS, SINGLE AXLE, OPPOSITE END |
| AAG1565 | 35 | SINGLE WHEELS IN-LINE SINGLE AXLE LOWBOYTYPE, ONE END |
| AAG1566 | 36 | SINGLE WHEELS, IN-LINE SINGLE AXLE LOWBO Y TYPE, ONE END SINGLE WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1567 | 37 | SINGLE WHEELS, IN-LINE SINGLE AXLES, LOW BOY TYPE, ONE END, SINGLE WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1568 | 38 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLES , LOWBOY TYPE ONE END, SINGLE WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1569 | 39 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLES , LOWBOY TYPE ONE END, DUAL WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1534 | 4 | SINGLE WHEELS, TANDEM SINGLE AXLES AT CE NTER |
| AAG1570 | 40 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLESLOWBOY TYPE, ONE END SINGLE WHEELS, SINGLE AXLE, OPPOSITE END |
| AAG1571 | 41 | DUAL WHEELS, TRIPLE SINGLE AXLES ONE END , SINGLE WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1572 | 42 | DUAL WHEELS, TRIPLE SINGLE AXLES ONE END , SINGLE WHEELS, TANDEM SINGLE AXLES, OPPOSITE END |
| AAG1573 | 43 | DUAL WHEELS, TRIPLE SINGLE AXLES ONE END , DUAL WHEELS SINGLE AXLE OPPOSITE END |
| AAG1574 | 44 | DUAL WHEELS, TRIPLE SINGLE AXLES, ONE EN D, DUAL WHEELS TANDEM SINGLE AXLES OPPOSITE |
| AAG1575 | 45 | DUAL WHEELS, TANDEM IN-LINE, SINGLE AXLE S, LOWBOY TYPE ONE END, SINGLE WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1576 | 46 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLESLOWBOY TYPE ONE END, SINGLE WHEELS TANDEM SINGLE AXLES OPPOSITE END |
| AAG1577 | 47 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLESLOWBOY TYPE ONE END, DUAL WHEELS, SINGLE AXLE OPPOSITE END |
| AAG1578 | 48 | DUAL WHEELS, TANDEM IN-LINE SINGLE AXLES , LOWBOY TYPE ONE END, DUAL WHEELS, TANDEM SINGLE AXLES OPPOSITE END |
| AAG1579 | 49 | SINGLE WHEELS, SINGLE AXLE ONE END,SINGL E WHEEL, SINGLE AXLE TRICYCLE TYPE OPPOSITE END |
| AAG1535 | 5 | SINGLE WHEELS, TANDEM SINGLE AXLES AT EN D |
| AAG1536 | 6 | SINGLE WHEELS, SINGLE AXLE EACH END |
| AAG1537 | 7 | SINGLE WHEELS SINGLE AXLE ONE END, SINGL E AXLE DOLLY SET OPPOSITE END |
| AAG1538 | 8 | SINGLE WHEELS, TANDEM SINGLE AXLES ONE E ND, SINGLE AXLE OPPOSITE END |
| AAG1539 | 9 | SINGLE WHEEL, TRIPLE SINGLE AXLE ON END |
CGWLAREAR DRIVE WHEEL QUANTITY
THE NUMBER OF REAR DRIVE WHEELS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(CGWLA10*)
CGWM*AFRONT DRIVE WHEEL QUANTITY
THE NUMBER OF FRONT DRIVE WHEELS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(CGWMA10*)
AGDQASTEERABLE WHEEL QUANTITY
THE NUMBER OF STEERABLE WHEELS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AGDQA10*)
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC CHHP, YOU MUST ANSWER MRC (APHE)
CHHPDOUTRIGGERS
AN INDICATION OF WHETHER OR NOT OUTRIGGERS ARE INCLUDED.
Enter the applicable reply code from the table below
(CHHPDB*;CHHPDC$DB*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
APHE*DOPERATION METHOD
THE MEANS USED TO OPERATE THE ITEM.
Enter the applicable reply code from the table below
(APHEDAABG*;APHEDAAAF$DAABG*)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAAF | MANUAL |
| AABG | POWER |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC CHXG, YOU MUST ANSWER MRC (ASFH and CNXQ and CHXH and CHXJ)
CHXGDPILE DRIVER
AN INDICATION OF WHETHER OR NOT A PILE DRIVER IS INCLUDED.
Enter the applicable reply code from the table below
(CHXGDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ASFH*JLEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A LEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASFHJFC2.0*;ASFHJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CNXQ*JBOOM LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNXQJFA2.0*;CNXQJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHXH*JHAMMER WEIGHT
A RELATIVE MEASURE OF THE MASS OF THE HAMMER WITH RESPECT TO ITS DENSITY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHXHJAJB2.0*;CHXHJAJB2.0$$JAJB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHXJ*JMAXIMUM PILE DIAMETER ACCOMMODATED
THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A PILE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHXJJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CHXKDCRANE OPERATOR CAB
AN INDICATION OF WHETHER OR NOT A CRANE OPERATOR(S) CAB IS INCLUDED.
Enter the applicable reply code from the table below
(CHXKDB*;CHXKDC$DB*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
PKWT*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PKWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
KZTS*DCOGNIZANT SERVICE
THE MILITARY SERVICE THAT INITIALLY PROCURED THE ITEM FROM THE CONTRACTOR.
Enter the applicable reply code from the table below
(KZTSDN)
| Table 1 |
| Reply Code (AP57) | Reply |
| F | UNITED STATES AIR FORCE |
| N | UNITED STATES NAVY |
| A | USA |
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAS3)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAI1)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information