A truck without a cab or driver's compartment, having the controls and driver's seat mounted on the platform body. The controls may be adjustable to permit the driver to operate the vehicle while walking. It may have troop seat(s) as an integral part of the body which folds flush with the platform when not in use. It may also have all-wheel drive and selective front or all-wheel steering.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED21847*)
CNTJ*JRATED LOAD CAPACITY
THE LOAD CAPACITY OF THE ITEM AS RATED BY THE MANUFACTURER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNTJJBY2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BX | METRIC TONS |
| BY | TONS |
CPKD*JVEHICLE MAXIMUM GROSS WEIGHT
THE MAXIMUM WEIGHT OF A FULLY EQUIPPED VEHICLE AND ALLOWABLE PAYLOAD OF CARGO OR PASSENGERS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CPKDJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| BX | METRIC TONS |
| AS | POUNDS |
AGDHAWHEEL QUANTITY
THE NUMBER OF WHEELS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AGDHA10*)
AGDJADRIVE WHEEL QUANTITY
THE NUMBER OF DRIVE WHEELS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AGDJA10*)
CNTKDDRIVE AXLE LOCATION
INDICATES THE LOCATION OF THE DRIVE AXLE ON THE ITEM.
Enter the applicable reply code from the table below
(CNTKDABC*;CNTKDABJ$DABC*;CNTKDABJ$$DABC*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABC | FRONT |
| ABJ | REAR |
IF STYLE/REPLY CODE(s) MM WERE ENTERED FOR MRC CNTL, YOU MUST ANSWER MRC (CNTM)
IF STYLE/REPLY CODE(s) MN WERE ENTERED FOR MRC CNTL, YOU MUST ANSWER MRC (CNTN)
CNTLDAXLE DRIVE TYPE
INDICATES THE TYPE OF MECHANISM USED TO TRANSMIT POWER AT THE REAR WHEELS.
Enter the applicable reply code from the table below
(CNTLDML*;CNTLDMR$$DCD*)
| Table 1 |
| Reply Code (AG25) | Reply |
| ML | AIR MOTOR |
| CD | CHAIN |
| MM | CONVENTIONAL |
| MN | DOUBLE REDUCTION |
| EE | ELECTRIC MOTOR |
| HB | HYDRAULIC MOTOR |
| MR | SINGLE REDUCTION |
CNTM*AAXLE SPEED QUANTITY
THE NUMBER OF REAR AXLE SPEEDS.
Enter the numeric reply with a minimum of one digit.
(CNTMA10*)
CNTN*DPOWER DIVIDER UNIT
AN INDICATION OF WHETHER OR NOT A POWER DIVIDER UNIT IS INCLUDED.
Enter the applicable reply code from the table below
(CNTNDB*;CNTNDC$DB*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
CNTP*DFRONT AXLE ENGAGING MECHANISM TYPE
INDICATES THE TYPE OF FRONT AXLE ENGAGING MECHANISM.
Enter the applicable reply code from the table below
(CNTPDFCG*;CNTPDBDR$DBDQ*)
| Table 1 |
| Reply Code (AK54) | Reply |
| BDQ | AUTOMATIC |
| FCG | CONSTANT |
| BDR | MANUAL |
CNTRJNOMINAL WHEELBASE
THE NOMINAL DISTANCE BETWEEN FRONT AND REAR AXLES OR BETWEEN THE FRONT AXLE AND CENTER POINT OF REAR MULTI-AXLE ASSEMBLIES/TANDEMS,TRIDEMS,ETC./.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNTRJC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| L | MILLIMETERS |
CNTS*JFRONT WHEEL TREAD NOMINAL WIDTH
THE NOMINAL TREAD DISTANCE BETWEEN THE CENTERS OF THE FRONT WHEELS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNTSJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| L | MILLIMETERS |
CNTT*JREAR WHEEL TREAD NOMINAL WIDTH
THE NOMINAL TREAD DISTANCE BETWEEN THE CENTERS OF THE REAR WHEELS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNTTJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| L | MILLIMETERS |
AKDJDPRIME MOVER TYPE
INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT.
Enter the applicable reply code from the table below
(AKDJDAC*;AKDJDAE$$DDH*)
| Table 1 |
| Reply Code (AG27) | Reply |
| AC | DIESEL ENGINE |
| DH | ELECTRIC |
| AE | GASOLINE ENGINE |
| DD | GASOLINE-ELECTRIC MOTOR |
AAXZACYLINDER QUANTITY
THE NUMBER OF CYLINDERS INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAXZA10*)
ALKKBENGINE BRAKE HORSEPOWER
THE POWER ACTUALLY DELIVERED BY THE ENGINE,AT A SPECIFIED SPEED,WHICH IS AVAILABLE FOR DRIVING THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALKKB2.0)
CTNY*JBRAKE POWER RATING
THE BRAKE POWER DELIVERED BY THE ITEM FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTNYJL2.0*)
| Table 1 |
| Reply Code (AC33) | Reply |
| L | KILOWATTS |
| W | WATTS |
CXQS*JENGINE POWER RATING
THE POWER PRODUCED BY THE ENGINE UNDER STANDARD OPERATING CONDITIONS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQSJNA2.0*)
| Table 1 |
| Reply Code (AJ20) | Reply |
| NA | HORSEPOWER |
| FG | KILOWATTS |
| HA | WATTS |
ALKL*BENGINE HORSEPOWER RATING SPEED IN RPM
THE ROTARY SPEED OF THE ENGINE AT WHICH THE HORSEPOWER RATING IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALKLB2.0)
CWNG*BENGINE KILOWATT RATING SPEED IN RPM
THE ROTARY SPEED OF THE ENGINE AT WHICH THE KILOWATT RATING IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CWNGB2.0)
BQXD*JPISTON DISPLACEMENT
THE VOLUME DISPLACED BY A PISTON IN A SINGLE STROKE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQXDJBA2.0*;BQXDJBA2.0$$JBA2.1*)
| Table 1 |
| Reply Code (AD42) | Reply |
| C | CUBIC CENTIMETERS |
| B | CUBIC INCHES |
| K | LITERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AAC WERE ENTERED FOR MRC AXJD, YOU MUST ANSWER MRC (AXJH)
IF STYLE/REPLY CODE(s) AAM WERE ENTERED FOR MRC AXJD, YOU MUST ANSWER MRC (CNTX and AXJF)
AXJDDTRANSMISSION TYPE
INDICATES THE TYPE OF TRANSMISSION USED TO TRANSFER DEVELOPED MECHANICAL ENERGY TO THE DRIVE UNIT.
Enter the applicable reply code from the table below
(AXJDDAAM)
| Table 1 |
| Reply Code (AM54) | Reply |
| AAM | AUTOMATIC |
| AAC | MANUAL |
AXJH*AFORWARD SPEED QUANTITY
THE NUMBER OF FORWARD SPEEDS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AXJHA10*)
CNTX*AFORWARD SPEED RANGE QUANTITY
THE NUMBER OF FORWARD SPEED RANGES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(CNTXA10*)
AXJF*AFORWARD SPEED QUANTITY PER RANGE
THE NUMBER OF FORWARD SPEEDS IN EACH RANGE.
Enter the numeric reply with a minimum of one digit.
(AXJFA10*)
IF STYLE/REPLY CODE(s) AAZ OR ABA WERE ENTERED FOR MRC CNTY, YOU MUST ANSWER MRC (CNTZ)
CNTY*DTRANSMISSION ADJUNCT TYPE
INDICATES THE TYPE OF ADJUNCT TRANSMISSION PROVIDED.
Enter the applicable reply code from the table below
(CNTYDAAZ*;CNTYDABB$DABA*;CNTYDABB$$DABA*)
| Table 1 |
| Reply Code (AM54) | Reply |
| AAZ | AUXILIARY |
| ABB | OVERDRIVE |
| ABA | TRANSFER |
CNTZ*ATRANSMISSION ADJUNCT SPEED QUANTITY
THE NUMBER OF SPEEDS PROVIDED IN THE TRANSMISSION ADJUNCT.
Enter the numeric reply with a minimum of one digit.
(CNTZA10*)
CNYWDBRAKE ACTUATION METHOD
THE MEANS BY WHICH THE BRAKES ARE ACTUATED.
Enter the applicable reply code from the table below
(CNYWDAAQ*;CNYWDAAN$DAAE*;CNYWDAAN$$DAAE*)
| Table 1 |
| Reply Code (AK88) | Reply |
| AAM | AIR |
| AAE | ELECTRIC |
| AAN | HYDRAULIC |
| AAP | MECHANICAL |
| AAQ | VACUUM |
IF STYLE/REPLY CODE(s) AACQ WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (CNZC)
IF STYLE/REPLY CODE(s) AACR WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (CNZB)
IF STYLE/REPLY CODE(s) AACX WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (AMKG and CNZF and CNZG)
IF STYLE/REPLY CODE(s) AADB WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (AYTC and CNZD)
IF STYLE/REPLY CODE(s) AADF WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (CHZG)
IF STYLE/REPLY CODE(s) AADG WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (CNZH)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAADG*;CBBLDAAGV$DAADM*;CBBLDAAGV$$DAADM*)
| Table 1 |
| Reply Code (AN47) | Reply |
| ARL | 110 VOLT CABLE, 25 FOOT LENGTH |
| AADM | A-FRAME |
| ABW | AIR BRAKE EMERGENCY SYSTEM |
| AADN | AIR CONDITIONING |
| AADP | ARTICULATED DESIGN |
| ACP | BATTERY HEATER |
| ABX | BATTERY HEATER W/THERMOSTAT |
| ARJ | BATTERY OPERATED PLANT HEATER |
| AADQ | BODY BASE CONVEYOR |
| AACA | BODY CREW COMPARTMENT |
| AADR | CAB PROTECTOR |
| AACC | CHUTE OPENING |
| ABY | DRIVE HUBS |
| ARG | DRIVERS COMPARTMENT AIR CONDITIONING |
| ABZ | DRIVERS COMPARTMENT HEATING |
| AACD | ELECTRICAL OUTLET |
| ARH | ENGINE RADIATOR HEATER |
| AACE | FABRIC TOP |
| AAGT | FLASHING RED LIGHT |
| AACF | FOLD DOWN SIDE |
| ACS | FRONT BUMPER PULL HOOKS |
| AACG | HEAVY DUTY CLUTCH |
| AACH | HEAVY DUTY COOLING SYSTEM |
| ACQ | HIGH LIFT BODY MECHANISM |
| AACJ | HOIST LOCKING DEVICE |
| ARK | HORIZONTAL SPINNING DISC SPREADER |
| ACA | HYDRAULIC DIGGER |
| ACB | HYDRAULIC POLE GRABBER |
| AACK | INSULATED |
| ACM | INTERPHONES |
| AAGU | JACK BRACKETS SUPPORT |
| AACL | LIQUID SUMP TANK |
| AACM | LOAD COMPACTER |
| ACE | LOADING RAMP |
| AACN | MATERIALS HANDLING CONTAINER |
| AACP | OUTRIGGER |
| ACK | OVERDRIVE |
| AACQ | POLE DERRICK |
| AACR | PORTABLE CONVEYOR CHUTE |
| ACR | POWER DIVIDER UNIT |
| ACF | POWER PLANT HEATER |
| AACS | POWER STEERING |
| AAGV | POWER TAKE-OFF |
| ACC | PULLEY |
| ACL | RADIO |
| AACT | RADIO EQUIPMENT PROVISION |
| ACG | REAR BUMPER |
| AACW | REAR MOUNTED ROLLER |
| AACX | REFRIGERATION UNIT |
| ACH | RIGHT HAND DRIVE |
| AACY | SIDE CURTAIN |
| AAGW | SIREN |
| AACZ | SLIDING ROOF |
| ACJ | SPOTLIGHT |
| AADA | STABILIZING JACK |
| ARM | STORM WINDOW |
| AADB | TAILGATE |
| AADC | TARPAULIN |
| AADD | TOP BOWS |
| AADE | TOWING PINTLE HOOK |
| AADF | TRAILER BRAKE CONNECTION |
| AADG | TURRET |
| AADH | UNDERWATER FORDING SYSTEM |
| AADJ | WINDOW BLACKOUT SHIELD |
| ACN | WINTERIZATION KIT |
CNZB*JCHUTE NOMINAL LENGTH
A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CHUTE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNZBJM2.0*;CNZBJM2.0$$JM2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| M | METERS |
CNZC*DDERRICK LOCATION
INDICATES THE LOCATION OF THE DERRICK.
Enter the applicable reply code from the table below
(CNZCDABJ)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABC | FRONT |
| ABJ | REAR |
AYTC*DHINGE LOCATION
INDICATES THE LOCATION OF THE HINGE/S/ ON THE ITEM.
Enter the applicable reply code from the table below
(AYTCDABD*;AYTCDABA$$DABA*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABA | BOTTOM |
| ABD | TOP |
CNZD*DTAILGATE OPERATION METHOD
THE MEANS BY WHICH THE TAILGATE IS OPERATED.
Enter the applicable reply code from the table below
(CNZDDAAAF)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAAF | MANUAL |
| AABG | POWER |
AMKG*DPOWER UNIT TYPE
INDICATES THE TYPE OF POWER UNIT INCLUDED WITH THE ITEM.
Enter the applicable reply code from the table below
(AMKGDABC*;AMKGDAAE$$DABC*)
| Table 1 |
| Reply Code (AJ13) | Reply |
| ABC | ELECTRIC MOTOR |
| AAE | GASOLINE ENGINE |
CNZF*JMAINTAINED INSIDE TEMP RATING
THE RATED INSIDE TEMPERATURE THAT IS MAINTAINED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNZFJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CNZG*JOUTSIDE TEMP AT WHICH INSIDE TEMP IS MAINTAINED
THE OUTSIDE TEMPERATURE AT WHICH THE INSIDE TEMPERATURE IS MAINTAINED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNZGJF2.0*;CNZGJF2.0$$JF2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CNZH*DTURRET TYPE
INDICATES THE TYPE OF TURRET PROVIDED.
Enter the applicable reply code from the table below
(CNZHDFDA)
| Table 1 |
| Reply Code (AK54) | Reply |
| FDB | NONTRAVERSING |
| FDA | TRAVERSING |
CPJR*AINTERIOR ELECTRICAL OUTLET VOLTAGE
THE VOLTAGE OF THE INTERIOR ELECTRICAL OUTLET/S/.
Enter the alpha-numeric reply with a minimum of one character.
(CPJRAM2)
CHZG*DTRAILER BRAKE CONNECTION TYPE
INDICATES THE TYPE OF TRAILER BRAKE CONNECTION(S) PROVIDED ON THE ITEM.
Enter the applicable reply code from the table below
(CHZGDEG*;CHZGDGJ$$DDJ*)
| Table 1 |
| Reply Code (AG25) | Reply |
| EG | AIR |
| GJ | ELECTRIC |
| DJ | HYDRAULIC |
| EA | VACUUM |
CNZPJCARGO AREA NOMINAL LENGTH
A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CARGO AREA.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNZPJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
CNZQJCARGO AREA NOMINAL WIDTH
A NOMINAL MEASUREMENT OF THE CARGO AREA TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNZQJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| C | CENTIMETERS |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
CPBGDOPERATOR CONTROL DESIGN
THE DESIGN OF THE CONTROLS FOR THE OPERATOR.
Enter the applicable reply code from the table below
(CPBGDFDL*;CPBGDFDM$$DATB*)
| Table 1 |
| Reply Code (AK54) | Reply |
| FDL | SITTING |
| FDM | STANDING |
| ATB | WALKING |
BYJFDSEAT TYPE
INDICATES THE TYPE OF SEAT PROVIDED.
Enter the applicable reply code from the table below
(BYJFDATD*;BYJFDCJW$DFHS*)
| Table 1 |
| Reply Code (AK54) | Reply |
| FHR | BENCH TYPE FRONT AND REAR |
| FHS | BENCH TYPE FRONT, INDIVIDUAL TYPE REAR |
| CJW | BUCKET |
| ATD | FOLDING |
| FHW | INDIVIDUAL TYPE FRONT AND REAR |
| FHT | INDIVIDUAL TYPE FRONT, BENCH TYPE REAR |
| APP | SWING |
CPBHDSEAT REMOVABILITY
AN INDICATION OF WHETHER OR NOT THE SEAT IS REMOVABLE.
Enter the applicable reply code from the table below
(CPBHDC*;CPBHDB$DB*)
| Table 1 |
| Reply Code (AC29) | Reply |
| C | NONREMOVABLE |
| B | REMOVABLE |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CPKC*JVEHICLE CURB WEIGHT
THE WEIGHT OF A FULLY EQUIPPED VEHICLE IN OPERATING CONDITION WITH A FULL COMPLEMENT OF FUEL,LUBRICANTS,AND COOLANT,BUT WITHOUT CREW OR PAYLOAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CPKCJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
CPJS*JRATED CUBIC CARRYING CAPACITY
A MEASUREMENT OF THE CARRYING CAPACITY OF THE ITEM RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CPJSJDR2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| GX | CUBIC METERS |
| DR | CUBIC YARDS |
AKSL*DPURPOSE FOR WHICH DESIGNED
THE PURPOSE FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AKSLDCF*;AKSLDCW$$DCS*)
| Table 1 |
| Reply Code (AG95) | Reply |
| CS | AIRCRAFT |
| CT | AIRCRAFT HANGER |
| BS | ARTILLERY REPAIR SHOP |
| BT | AUTOMOTIVE REPAIR SHOP |
| BX | CONSTRUCTION EQUIPMENT REPAIR SHOP |
| BY | ELECTRICAL REPAIR SHOP |
| DG | HOUSE FOOD SUPPLIES |
| CA | LIGHT MAINTENANCE SHOP |
| CW | LINE CONSTRUCTION |
| CX | LINE MAINTENANCE |
| CC | MACHINE SHOP |
| CD | ORDNANCE MAINTENANCE SHOP |
| DF | PIPELINE CONSTRUCTION |
| DE | PIPELINE MAINTENANCE |
| CE | POLE SETTING AND MAINTENANCE |
| CF | SMALL ARMS REPAIR SHOP |
| CG | STREET LIGHT MAINTENANCE |
| CY | TELEPHONE INSTALLATION |
| CZ | TELEPHONE MAINTENANCE |
| CJ | TIRE REPAIR SHOP |
| CK | TOOL REPAIR SHOP |
| DH | TRANSPORT FOOD SUPPLIES |
| CL | WELDING SHOP |
CPJW*GBODY MANUFACTURER CODE AND MODEL NUMBER
THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE BODY FURNISHED WITH THE ITEM AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA IN PLACE OF THIS DISCONTINUED MRC WITH USE OF ISAC.
Enter clear text.
(CPJWGCLEARTEXT)
AGEA*GENGINE/MOTOR MANUFACTURER CODE AND MODEL NUMBER
THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE ENGINE/MOTOR (PRIME MOVER) FURNISHED WITH THE ITEM AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA IN PLACE OF THIS DISCONTINUED MRC.
Enter clear text.
(AGEAGCLEARTEXT)
CPJX*GCHASSIS MANUFACTURER CODE AND MODEL NUMBER
THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE CHASSIS AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter clear text.
(CPJXGCLEARTEXT)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAV0)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAO0)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AATDMGA000*;MATT3AATDMGA000$DMGA000*;MATT3AATDMGA000$$DMGA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| MGA000 | MAGNESIUM |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information