An item whose reflection properties are similar to those of a radar target. It is designed for fixed position installation so that its range and azimuth, with respect to the equipment with which it is used is known. It is normally used for the calibration of a radar set. See also TARGET, RADAR.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED19080*)
ALBNJREFLECTING ELEMENT OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE REFLECTING ELEMENT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALBNJAC2.0*;ALBNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALBP*JREFLECTING ELEMENT OVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE REFLECTING ELEMENT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALBPJAC2.0*;ALBPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALBR*JREFLECTING ELEMENT OVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE REFLECTING ELEMENT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALBRJAC2.0*;ALBRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALBS*JREFLECTING ELEMENT OVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE REFLECTING ELEMENT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALBSJAC2.0*;ALBSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALBTJREFLECTING ELEMENT FREQUENCY RATING
THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE REFLECTING ELEMENT IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALBTJEA2.0*;ALBTJEA2.0$$JEA2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| G | GIGAHERTZ |
| E | HERTZ |
| K | KILOHERTZ |
| M | MEGAHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGUC*AUNIT PACKAGE QUANTITY
THE NUMBER OF ITEMS CONTAINED IN THE UNIT PACKAGE.
Enter the numeric reply with a minimum of one digit.
(AGUCA10*)
AGXZ*DUNIT PACKAGE TYPE
INDICATES THE TYPE OF CONTAINER IN WHICH THE ITEM OF SUPPLY IS PACKAGED. PLEASE USE MRC ALQG IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AGXZDAJ*;AGXZDAH$DAK*)
| Table 1 |
| Reply Code (AE96) | Reply |
| AE | BAG |
| AB | BOX |
| AH | CAN |
| AJ | CARTON |
| AK | CASE |
AKWA*GJOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM NAME
THE NAME ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM.USE MRC AKSJ AND RELATIONSHIP TO MRC AMSB
Enter clear text.
(AKWAGCLEARTEXT)
AKWB*GJOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM TYPE NUMBER
THE TYPE NUMBER ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM. USE MRC AMSB
Enter clear text.
(AKWBGCLEARTEXT)
IF STYLE/REPLY CODE(s) P WERE ENTERED FOR MRC RADC, YOU MUST ANSWER MRC (RADD)
RADC*DRADIOACTIVE CONTENT
AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS.
Enter the applicable reply code from the table below
(RADCDP)
| Table 1 |
| Reply Code (AN54) | Reply |
| P | CONTAINS RADIOACTIVE MATERIAL |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
RADD*JRADIONUCLIDES DATA
THE NAME AND AMOUNT OF THE RADIONUCLIDE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(RADDJJHAAGJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| JF | CURIES |
| JH | MICROCURIES |
| JG | MILLICURIES |
| Table 2 |
| Reply Code (AN55) | Reply |
| AAAB | ACTINIUM (89) AC-227 |
| AAAC | ACTINIUM (89) AC-228 |
| AAAD | AMERICIUM (95) AM-241 |
| AAAE | AMERICIUM (95) AM-243 |
| AAAF | ANTIMONY (51) SB-122 |
| AAAG | ANTIMONY (51) SB-124 |
| AAAH | ANTIMONY (51) SB-125 |
| AAAJ | ARGON (18) AR-37 |
| AAAK | ARGON (18) AR-41 |
| AAAL | ARGON (18) AR-41, UNCOMPRESSED |
| AAAM | ARSENIC (33) AS-73 |
| AAAN | ARSENIC (33) AS-74 |
| AAAP | ARSENIC (33) AS-76 |
| AAAQ | ARSENIC (33) AS-77 |
| AAAR | ASTATINE (85) AT-211 |
| AAAS | BARIUM (56) BA-131 |
| AAAT | BARIUM (56) BA-133 |
| AAAW | BARIUM (56) BA-140 |
| AAAX | BERKELIUM (97) BK-249 |
| AAAY | BERYLLIUM (4) BE-7 |
| AAAZ | BISMUTH (83) BI-206 |
| AABA | BISMUTH (83) BI-207 |
| AABB | BISMUTH (83) BI-210 |
| AABC | BISMUTH (83) BI-212 |
| AABD | BROMINE (35) BR-82 |
| AABE | CADMIUM (48) CD-109 |
| AABG | CADMIUM (48) CD-115 |
| AABF | CADMIUM (48) CD-115M |
| AABH | CALCIUM (20) CA-45 |
| AABJ | CALCIUM (20) CA-47 |
| AABK | CALIFORNIUM /98/ CF-249 |
| AABL | CALIFORNIUM /98/ CF-250 |
| AABM | CALIFORNIUM /98/ CF-252 |
| AABN | CARBON (6) C-14 |
| AABP | CERIUM (58) CE-141 |
| AABQ | CERIUM (58) CE-143 |
| AABR | CERIUM (58) CE-144 |
| AABS | CESIUM (55) CS-131 |
| AABW | CESIUM (55) CS-134 |
| AABT | CESIUM (55) CS-134M |
| AABX | CESIUM (55) CS-135 |
| AABY | CESIUM (55) CS-136 |
| AABZ | CESIUM (55) CS-137 |
| AACA | CHLORINE (17) CL-36 |
| AACB | CHLORINE (17) CL-38 |
| AACC | CHROMIUM (24) CR-51 |
| AACD | COBALT (27) CO-56 |
| AACE | COBALT (27) CO-57 |
| AACG | COBALT (27) CO-58 |
| AACF | COBALT (27) CO-58M |
| AACH | COBALT (27) CO-60 |
| AACJ | COPPER (29) CU-64 |
| AACK | CURIUM (96) CM-242 |
| AACL | CURIUM (96) CM-243 |
| AACM | CURIUM (96) CM-244 |
| AACN | CURIUM (96) CM-245 |
| AACP | CURIUM (96) CM-246 |
| AACQ | DYSPROSIUM (66) DY-154 |
| AACR | DYSPROSIUM (66) DY-165 |
| AACS | DYSPROSIUM (66) DY-166 |
| AACT | ERBIUM (68) ER-169 |
| AACW | ERBIUM (68) ER-171 |
| AACX | EUROPIUM (63) EU-150 |
| AACZ | EUROPIUM (63) EU-152 |
| AACY | EUROPIUM (63) EU-152M |
| AADA | EUROPIUM (63) EU-154 |
| AADB | EUROPIUM (63) EU-155 |
| AADC | FLUORINE (9) F-18 |
| AADD | GADOLINIUM (64) GD-153 |
| AADE | GADOLINIUM (64) GD-159 |
| AADF | GALLIUM (31) GA-67 |
| AADG | GALLIUM (31) GA-72 |
| AADH | GERMANIUM (32) GE-71 |
| AADJ | GOLD (79) AU-193 |
| AADK | GOLD (79) AU-194 |
| AADL | GOLD (79) AU-195 |
| AADM | GOLD (79) AU-196 |
| AADN | GOLD (79) AU-198 |
| AADP | GOLD (79) AU-199 |
| AADQ | HAFNIUM (72) HF-181 |
| AADR | HOLMIUM (67) HO-166 |
| AADS | INDIUM (49) IN-113M |
| AADT | INDIUM (49) IN-114M |
| AADX | INDIUM (49) IN-115 |
| AADW | INDIUM (49) IN-115M |
| AADY | IODINE (53) I-124 |
| AADZ | IODINE (53) I-125 |
| AAEA | IODINE (53) I-126 |
| AAEB | IODINE (53) I-129 |
| AAEC | IODINE (53) I-131 |
| AAED | IODINE (53) I-132 |
| AAEE | IODINE (53) I-133 |
| AAEF | IODINE (53) I-134 |
| AAEG | IODINE (53) I-135 |
| AAEH | IRIDIUM (77) IR-190 |
| AAEJ | IRIDIUM (77) IR-192 |
| AAEK | IRIDIUM (77) IR-194 |
| AAEL | IRON (26) FE-55 |
| AAEM | IRON (26) FE-59 |
| AAEQ | KRYPTON (36) KR-85 |
| AAER | KRYPTON (36) KR-85, UNCOMPRESSED |
| AAEN | KRYPTON (36) KR-85M |
| AAEP | KRYPTON (36) KR-85M, UNCOMPRESSED |
| AAES | KRYPTON (36) KR-87 |
| AAET | KRYPTON (36) KR-87, UNCOMPRESSED |
| AAEW | LANTHANUM (57) LA-140 |
| AAEX | LEAD (82) PB-203 |
| AAEY | LEAD (82) PB-210 |
| AAEZ | LEAD (82) PB-212 |
| AAFA | LUTECIUM (71) LU-172 |
| AAFB | LUTECIUM (71) LU-177 |
| AAFC | MAGNESIUM (12) MG-28 |
| AAFD | MANGANESE (25) MN-52 |
| AAFE | MANGANESE (25) MN-54 |
| AAFF | MANGANESE (25) MN-56 |
| AAFH | MERCURY (80) HG-197 |
| AAFG | MERCURY (80) HG-197M |
| AAFJ | MERCURY (80) HG-203 |
| AAFK | MIXED FISSION PRODUCTS MF-P |
| AAFL | MOLYBDENUM (42) MO-99 |
| AAFM | NEODYMIUM (60) ND-147 |
| AAFN | NEODYMIUM (60) ND-149 |
| AAFP | NEPTUNIUM (93) NP-237 |
| AAFQ | NEPTUNIUM (93) NP-239 |
| AAFR | NICKEL (28) NI-56 |
| AAFS | NICKEL (28) NI-59 |
| AAFT | NICKEL (28) NI-63 |
| AAFW | NICKEL (28) NI-65 |
| AAFX | NIOBIUM (41) NB-93M |
| AAFY | NIOBIUM (41) NB-95 |
| AAFZ | NIOBIUM (41) NB-97 |
| AAGA | OSMIUM (76) OS-185 |
| AAGC | OSMIUM (76) OS-191 |
| AAGB | OSMIUM (76) OS-191M |
| AAGD | OSMIUM (76) OS-193 |
| AAGE | PALLADIUM (46) PD-103 |
| AAGF | PALLADIUM (46) PD-109 |
| AAGG | PHOSPHORUS (15) P-32 |
| AAGH | PLATINUM (78) PT-191 |
| AAGJ | PLATINUM (78) PT-193 |
| AAGK | PLATINUM (78) PT-193M |
| AAGM | PLATINUM (78) PT-197 |
| AAGL | PLATINUM (78) PT-197M |
| AAGN | PLUTONIUM (94) PU-238 |
| AAGP | PLUTONIUM (94) PU-239 |
| AAGQ | PLUTONIUM (94) PU-240 |
| AAGR | PLUTONIUM (94) PU-241 |
| AAGS | PLUTONIUM (94) PU-242 |
| AAGT | POLONIUM (84) PO-210 |
| AAGW | POTASSIUM (19) K-42 |
| AAGX | POTASSIUM (19) K-43 |
| AAGY | PRASEODYMIUM (59) PR-142 |
| AAGZ | PRASEODYMIUM (59) PR-143 |
| AAHA | PROMETHIUM (61) PM-147 |
| AAHB | PROMETHIUM (61) PM-149 |
| AAHC | PROTACTINIUM (91) PA-230 |
| AAHD | PROTACTINIUM (91) PA-231 |
| AAHE | PROTACTINIUM (91) PA-233 |
| AAHF | RADIUM (88) RA-223 |
| AAHG | RADIUM (88) RA-224 |
| AAHH | RADIUM (88) RA-226 |
| AAHJ | RADIUM (88) RA-228 |
| AAHK | RADON (86) RN-220 |
| AAHL | RADON (86) RN-222 |
| AAHM | RHENIUM (75) RE-183 |
| AAHN | RHENIUM (75) RE-186 |
| AAHP | RHENIUM (75) RE-187 |
| AAHQ | RHENIUM (75) RE-188 |
| AAHR | RHENIUM (75) RE-NATURAL |
| AAHS | RHODIUM (45) RH-103M |
| AAHT | RHODIUM (45) RH-105 |
| AAHW | RUBIDIUM (37) RB-86 |
| AAHX | RUBIDIUM (37) RB-87 |
| AAHY | RUBIDIUM (37) RB-NATURAL |
| AAJA | RUTHENIUM (44) RU-103 |
| AAJB | RUTHENIUM (44) RU-105 |
| AAJC | RUTHENIUM (44) RU-106 |
| AAHZ | RUTHENIUM (44) RU-97 |
| AAJD | SAMARIUM (62) SM-145 |
| AAJE | SAMARIUM (62) SM-147 |
| AAJF | SAMARIUM (62) SM-151 |
| AAJG | SAMARIUM (62) SM-153 |
| AAJH | SCANDIUM (21) SC-46 |
| AAJJ | SCANDIUM (21) SC-47 |
| AAJK | SCANDIUM (21) SC-48 |
| AAJL | SELENIUM (34) SE-75 |
| AAJM | SILICON (14) SI-31 |
| AAJN | SILVER (47) AG-105 |
| AAJP | SILVER (47) AG-110M |
| AAJQ | SILVER (47) AG-111 |
| AAJR | SODIUM (11) NA-22 |
| AAJS | SODIUM (11) NA-24 |
| AAJW | STRONTIUM (38) SR-85 |
| AAJT | STRONTIUM (38) SR-85M |
| AAJX | STRONTIUM (38) SR-89 |
| AAJY | STRONTIUM (38) SR-90 |
| AAJZ | STRONTIUM (38) SR-91 |
| AAKA | STRONTIUM (38) SR-92 |
| AAKB | SULPHUR (16) S-35 |
| AAKC | TANTALUM (73) TA-182 |
| AAKE | TECHNETIUM (43) TC-96 |
| AAKD | TECHNETIUM (43) TC-96M |
| AAKG | TECHNETIUM (43) TC-97 |
| AAKF | TECHNETIUM (43) TC-97M |
| AAKJ | TECHNETIUM (43) TC-99 |
| AAKH | TECHNETIUM (43) TC-99M |
| AAKK | TELLURIUM (52) TE-125M |
| AAKM | TELLURIUM (52) TE-127 |
| AAKL | TELLURIUM (52) TE-127M |
| AAKP | TELLURIUM (52) TE-129 |
| AAKN | TELLURIUM (52) TE-129M |
| AAKQ | TELLURIUM (52) TE-131M |
| AAKR | TELLURIUM (52) TE-132 |
| AAKS | TERBIUM (65) TB-160 |
| AAKT | THALLIUM (81) TL-200 |
| AAKW | THALLIUM (81) TL-201 |
| AAKX | THALLIUM (81) TL-202 |
| AAKY | THALLIUM (81) TL-204 |
| AAKZ | THORIUM (90) TH-227 |
| AALA | THORIUM (90) TH-228 |
| AALB | THORIUM (90) TH-230 |
| AALC | THORIUM (90) TH-231 |
| AALD | THORIUM (90) TH-232 |
| AALE | THORIUM (90) TH-234 |
| AALF | THORIUM (90) TH-NATURAL |
| AALG | THULIUM (69) TM-168 |
| AALH | THULIUM (69) TM-170 |
| AALJ | THULIUM (69) TM-171 |
| AALK | TIN (50) SN-113 |
| AALL | TIN (50) SN-117M |
| AALM | TIN (50) SN-121 |
| AALN | TIN (50) SN-125 |
| AALP | TRITIUM (1) H-3 |
| AALQ | TRITIUM (1) H-3 AS GAS, LUMINOUS PAINT, OR ADSORBED ON SOLID MATERIAL |
| AALR | TUNGSTEN (74) W-181 |
| AALS | TUNGSTEN (74) W-185 |
| AALT | TUNGSTEN (74) W-187 |
| AALW | URANIUM (92) U-230 |
| AALX | URANIUM (92) U-232 |
| AALY | URANIUM (92) U-233 |
| AALZ | URANIUM (92) U-234 |
| AAMA | URANIUM (92) U-235 |
| AAMB | URANIUM (92) U-236 |
| AAMC | URANIUM (92) U-238 |
| AAMF | URANIUM (92) U-DEPLETED |
| AAME | URANIUM (92) U-ENRICHED |
| AAMD | URANIUM (92) U-NATURAL |
| AAMG | VANADIUM (23) V-48 |
| AAMH | VANADIUM (23) V-49 |
| AAMJ | XENON (54) XE-125 |
| AAMK | XENON (54) XE-131M |
| AAML | XENON (54) XE-131M, UNCOMPRESSED |
| AAMM | XENON (54) XE-133 |
| AAMN | XENON (54) XE-133, UNCOMPRESSED |
| AAMP | XENON (54) XE-135 |
| AAMQ | XENON (54) XE-135, UNCOMPRESSED |
| AAMR | YTTERBIUM (70) YB-175 |
| AAMS | YTTRIUM (39) Y-88 |
| AAMT | YTTRIUM (39) Y-90 |
| AAMX | YTTRIUM (39) Y-91 |
| AAMW | YTTRIUM (39) Y-91M |
| AAMY | YTTRIUM (39) Y-92 |
| AAMZ | YTTRIUM (39) Y-93 |
| AANA | ZINC (30) ZN-65 |
| AANC | ZINC (30) ZN-69 |
| AANB | ZINC (30) ZN-69M |
| AAND | ZIRCONIUM (40) ZR-93 |
| AANE | ZIRCONIUM (40) ZR-95 |
| AANF | ZIRCONIUM (40) ZR-97 |
PKWT*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PKWTJKG2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDRHA000$DPTA000*;PRMTDRHA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000F2.0*;PMWTJPDA000F2.0$$JPDA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAA7)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAB3)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDALB000*;MATT3AEEDALB000$DSTA000*;MATT3AEEDALB000$$DSTA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACW | FRAME |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HWW | REFLECTING ELEMENT |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| STA000 | STEEL |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDPNA000*;SFTT3AEEDPNA000$DPNA000*;SFTT3AEEDPNA000$$DPNA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACW | FRAME |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HWW | REFLECTING ELEMENT |
| Table 2 |
| Reply Code (SF01) | Reply |
| PNA000 | PAINT |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information