An insulator that is essentially thin, flat, and round in shape, with or without holes. The general shape may vary by the addition of such features as beveled edges, indented surfaces, through-hole key and/or peripheral flats. It may have one or more holes off center; if there are two or more holes, one may be centrally located. Excludes:MOUNTING PAD, ELECTRICAL-ELECTRONIC COMPONENT.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED18295*)
IF STYLE/REPLY CODE(s) E1 OR E22 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABKW)
IF STYLE/REPLY CODE(s) E2 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQZZ and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E3 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and AGPX and ABKV and CRTT)
IF STYLE/REPLY CODE(s) E4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AFFL and ABTB and ABKW and CRTT and AGPX and ABKV and AASY and CRKY)
IF STYLE/REPLY CODE(s) E5 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CRKY and CQSH and ABRD and ABRC and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRC and CQSH and CRKY and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQSH and CRKY and ABKV and CFNT and BXCZ and ABKW and ABRC)
IF STYLE/REPLY CODE(s) E8, E9, E10, E11 OR E12 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQSH and CRKY and ABKV and ABKW and ABRC)
IF STYLE/REPLY CODE(s) E13 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQSH and ABRC and ABRD and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E14 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CRKY and CQSH and ABRC and ABRD and AGML and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E15 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRC and ACDK and CRKY and AGML and ABRD and CQSH and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E16 OR E18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQSH and ABRC and ABRD and CRKY and ABKV and ABKW)
IF STYLE/REPLY CODE(s) E17 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQZZ and ABRC and CRTB and ABKV and CQDL and ABRD and CQSH and CRKY and ABKW)
IF STYLE/REPLY CODE(s) E20 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AASY and ABRC and CRTB and ABRD and CRKY and CQSH and ABKV and AGMM and ACDK and ABKW and AGML)
IF STYLE/REPLY CODE(s) E21 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPR and AJEK and CCFJ and ABKW and CQDN and CRYZ and BZLN and CFNT and BXCZ and ABKV)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLE4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BZ10086 | E1 | FLAT, ROUND |
| BZ10095 | E10 | DRILLED, FLAT |
| BZ10096 | E11 | DRILLED, FLAT |
| BZ10097 | E12 | DRILLED, FLAT |
| BZ10098 | E13 | DRILLED, FLAT |
| BZ10099 | E14 | DRILLED, FLAT |
| BZ10100 | E15 | DRILLED, FLAT |
| BZ10101 | E16 | DRILLED, FLAT |
| BZ10102 | E17 | DRILLED, FLATTED |
| BZ10103 | E18 | DRILLED, FLAT |
| BZ10087 | E2 | FLATTED, ROUND |
| BZ10104 | E20 | DRILLED, FLATTED |
| BZ10105 | E21 | ROUND, SLOTTED |
| BZ10106 | E22 | FLAT, ROUND |
| BZ10088 | E3 | FLANGED ROUND |
| BZ10089 | E4 | FLANGED ROUND |
| BZ10090 | E5 | DRILLED, FLAT |
| BZ10091 | E6 | DRILLED, FLAT |
| BZ10092 | E7 | DRILLED, FLAT |
| BZ10093 | E8 | DRILLED, FLAT |
| BZ10094 | E9 | DRILLED, FLAT |
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJAB2.0*;AASYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAC2.0*;ABKVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAC2.0*;ABKWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPR*JFIRST STEP DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPRJAC2.0*;ABPRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRC*JFIRST HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRCJAA2.0*;ABRCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRD*JSECOND HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRDJAB2.0*;ABRDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACDK*BFIRST ANGULAR SPACING IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACDKB2.0)
AFFL*JMOUNTING BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFFLJAB2.0*;AFFLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGML*JTHIRD HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGMLJAA2.0*;AGMLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGMM*JFOURTH HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGMMJAA2.0*;AGMMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGPX*JSHOULDER OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHOULDER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGPXJAB2.0*;AGPXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEK*JFIRST STEP HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEKJAB2.0*;AJEKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAB2.0*;ASDBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BXCZ*JFIRST COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXCZJAC2.0*;BXCZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BZLN*JSECOND COUNTERBORE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BZLNJAB2.0*;BZLNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CCFJ*JSECOND COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CCFJJAC2.0*;CCFJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFNT*JFIRST COUNTERBORE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFNTJAB2.0*;CFNTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQDL*JFOURTH HOLE SPACING
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQDLJAA2.0*;CQDLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQDN*JFIRST SLOT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQDNJAB2.0*;CQDNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQSH*JFIRST HOLE SPACING
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQSHJAC2.0*;CQSHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQZZ*JDISTANCE FROM OUTSIDE FLATTED PORTION TO OPPOSITE SURFACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQZZJAB2.0*;CQZZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRKY*JSECOND HOLE SPACING
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRKYJAC2.0*;CRKYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRTB*JTHIRD HOLE SPACING
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRTBJAC2.0*;CRTBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRTT*JSHOULDER DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRTTJAB2.0*;CRTTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRYZ*JFIRST SLOT DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRYZJAA2.0*;CRYZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
STLC*HSURFACE TREATMENT AND LOCATION
THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM AND ITS LOCATION. PLEASE USE MRC SFTT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Tables 1 & 2 below.
(STLCHCSDCD00002.0*;STLCHCSDCD00002.0$HCSDCD00002.0*;STLCHCSDCD00002.0$$HCSDCD00002.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| BSE | BASE |
| CAP | CAP |
| CSD | CENTER STUD |
| ETM | ELECTRICAL TERMINATION |
| FCB | FIRST COUNTERBORE |
| GKT | GASKET |
| MTB | MOUNTING BASE |
| MTF | MOUNTING FACILITY |
| AAD | OVERALL |
| SCB | SECOND COUNTERBORE |
| SNK | SHANK |
| SLD | SHIELD |
| Table 2 |
| Reply Code (AD09) | Reply |
| AN0000 | ANODIZED |
| AAAAAA | ANY ACCEPTABLE |
| BA0000 | BLACK OXIDE |
| BA0001 | BLACK OXIDE, MIL-F-495 |
| CD0000 | CADMIUM |
| CDR000 | CADMIUM PLATED |
| CDAL00 | CADMIUM PLATED W/CHROMATE |
| CD0008 | CADMIUM, QQ-P-416, TYPE 2, CLASS 2 |
| CD0014 | CADMIUM, QQ-P-416, TYPE 2, CLASS C |
| CNW000 | CHROMATE TREATMENT |
| GB0000 | GALVANIZED |
| GL0000 | GLAZED |
| NF0000 | NICKEL |
| NFG000 | NICKEL PLATED |
| NF0109 | NICKEL PLATING, QQ-N-290 |
| PH0000 | PHOSPHATE |
| PH0002 | PHOSPHATE, MIL-C-16232-CANCELED |
| AG0000 | SILVER |
| SJF000 | SOLDER COATED |
| SJC000 | SOLDER DIP, HOT |
| SN0004 | TIN PLATE, MIL-T-10727, TYPE 1 OR 2 |
| SNF000 | TIN PLATED |
| SN0002 | TIN PLATED, MIL-T-10727, TYPE 1 |
| SN0003 | TIN PLATED, MIL-T-10727, TYPE 2 |
| TD0000 | TINNED DIPPED, HOT |
| VA0001 | VARNISHED, MIL-V-173 |
| ZN0000 | ZINC |
| ZN0006 | ZINC, QQ-Z-325, TYPE 2, CLASS 3 |
AAPC*DIDENTIFICATION CODE COLOR
THE APPLICATION OF COLOR OR A SERIES OF COLORS FOR THE EXPRESSED PURPOSE OF IDENTIFYING THE SPECIFIC FUNCTIONAL DESIGN AND/OR THE SYSTEM APPLICATION OF AN ITEM.
Enter the applicable reply code from the table below
(AAPCDGY0000*;AAPCDGR0000$DBL0000*;AAPCDGR0000$$DBL0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AM0000 | AMBER |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BU0000 | BLUE |
| BR0000 | BROWN |
| BR0008 | BROWN, CHOCOLATE |
| BR0071 | BROWN, GRAY |
| BR0003 | BROWN, LIGHT |
| MS0013 | BUFF |
| CL0000 | CLEAR |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| GR0026 | GREEN, GRAY |
| NA0000 | NATURAL |
| LD0000 | OLIVE DRAB |
| RG0000 | ORANGE |
| RE0000 | RED |
| RE0020 | RUBY |
| SL0000 | SILVER |
| TA0000 | TAN |
| VL0000 | VIOLET |
| WH0000 | WHITE |
| YE0000 | YELLOW |
UKBG*JDIELECTRIC MATERIAL VOLTAGE RATING PER UNIT THICKNESS
THE MAXIMUM POTENTIAL GRADIENT THE INSULATING MATERIAL CAN WITHSTAND,PER UNIT THICKNESS,WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(UKBGJAB2.0*)
| Table 1 |
| Reply Code (AP24) | Reply |
| AC | KILOVOLTS PER MILLIMETER |
| AB | VOLTS PER MIL /0.001 INCH/ |
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
BDPK*JASBESTOS CONTENT PERCENTAGE
THE ASBESTOS CONTENT OF THE ITEM,EXPRESSED IN PERCENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDPKJC2.0*;BDPKJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) JG WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (BDPK)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDJG)
| Table 1 |
| Reply Code (EN02) | Reply |
| JG | ASBESTOS ALTERNATIVE PRODUCTS |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDLB*;ADZCDCY$$DMP*)
| Table 1 |
| Reply Code (AA65) | Reply |
| LB | ELECTRIC ARCING |
| GP | FUNGUS RESISTANT |
| CY | HEAT RESISTANT |
| MP | MILDEW PROOFED |
| AJ | MILDEW RESISTANT |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDF)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000R2.0*;PMWTJPDA000R2.0$$JPDA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPDA000*;PRMTDRTA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ008*;HZRDDHAZ052$$DHAZ042*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ008 | CADMIUM |
| HAZ052 | ZINC |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AYKDWDM000*;MATT3AYKDWDM000$DRCE000*;MATT3AYKDWDM000$$DRCE000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABE | BASE |
| 3AEE | OVERALL |
| 3AHZ | MOUNTING FACILITY |
| 3AYK | GASKET |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ADA000 | ADHESIVE |
| ALD000 | ALUMINA |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL6061 | ALUMINUM ALLOY 6061 |
| ALE000 | ALUMINUM OXIDE |
| ASA000 | ASBESTOS |
| BEC000 | BERYLLIUM OXIDE |
| CNA000 | CARBON |
| CSA000 | CELLULOSE |
| CLD000 | CERAMIC |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| FBA000 | FIBER |
| AAA035 | FIBERGLASS CLOTH REINFORCED SILICONE RUBBER |
| GSA000 | GLASS |
| GSU000 | GLASS CLOTH |
| GSB000 | GLASS FIBER |
| AAA044 | LAMINATED PLASTIC |
| AYA000 | MICA |
| PPA000 | PAPER |
| PPJ000 | PAPERBOARD |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCE000 | PLASTIC ALKYD |
| PCG000 | PLASTIC DIALLYL PHTHALATE |
| PCH000 | PLASTIC EPOXY |
| PCJ000 | PLASTIC MELAMINE |
| PCBB00 | PLASTIC METHACRYLATE |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCDL00 | PLASTIC POLYAMIDE GLASS FILLED |
| PCQ000 | PLASTIC POLYCAPROLACTAM |
| PCR000 | PLASTIC POLYCARBONATE |
| PCT000 | PLASTIC POLYCHLOROTRIFLUOROETHYLENE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCZ000 | PLASTIC POLYHEXAMETHYLENE ADIPAMIDE |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| PCAA00 | PLASTIC POLYHEXAMETHYLENE SEBACAMIDE |
| PCAAAA | PLASTIC POLYPHENYLENE OXIDE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAAAB | PLASTIC POLYUNDECANOAMIDE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| PCAK00 | PLASTIC SILICONE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PCAP00 | PLASTIC VINYL |
| WDM000 | PRESSBOARD |
| RSB000 | RESIN SILICONE |
| RCE000 | RUBBER |
| RC0021 | RUBBER SILICONE CLASS Q |
| RCB000 | RUBBER SYNTHETIC |
| SLD000 | SILICA |
| STA000 | STEEL |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCLJMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABE | BASE |
| 3AEE | OVERALL |
| 3AHZ | MOUNTING FACILITY |
| 3AYK | GASKET |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information