An assembled unit consisting of a commonly mounted centrifugal pump(s), prime mover(s), and the necessary components to provide for a complete operation.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED17988*)
AHYVJMAXIMUM DISCHARGE FLOW RATE
THE MAXIMUM RATED CAPACITY DELIVERED BY THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYVJE2.0*;AHYVJE2.0$$JE2.1*)
| Table 1 |
| Reply Code (AC64) | Reply |
| M | GALLONS PER MINUTE |
| E | LITERS PER MINUTE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
AHYWJDISCHARGE PRESSURE
THE PRESSURE OF THE MEDIA DELIVERED BY THE ITEM AT MAXIMUM RATED DISCHARGE CAPACITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYWJG2.0*;AHYWJG2.0$$JG2.1*)
| Table 1 |
| Reply Code (AB18) | Reply |
| C | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
AHYXJTOTAL HEAD
THE SUM OF THE TOTAL DISCHARGE HEAD AND THE TOTAL SUCTION LIFT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYXJF2.0*;AHYXJF2.0$$JF2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
AHYYJSUCTION LIFT
THE VERTICAL DISTANCE FROM THE LEVEL OF SUPPLY TO THE CENTER OF THE PUMP.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYYJF2.0*;AHYYJF2.0$$JF2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
AHYZJOPERATING SPEED AT RATED CAPACITY
THE SPEED OF THE ITEM REQUIRED TO PRODUCE ITS RATED CAPACITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYZJE2.0*;AHYZJE2.0$$JE2.1*)
| Table 1 |
| Reply Code (AA22) | Reply |
| D | REVOLUTIONS PER MINUTE |
| E | STROKES PER MINUTE |
AHZADPUMPING ELEMENT OPERATING POSITION
THE POSITION IN WHICH THE PUMPING ELEMENT/S/ IS DESIGNED TO OPERATE.
Enter the applicable reply code from the table below
(AHZADD)
| Table 1 |
| Reply Code (AC60) | Reply |
| D | VERTICAL |
| B | HORIZONTAL |
AHZEDCENTRIFUGAL PUMP DESIGN
THE DESIGN OF A CENTRIFUGAL PUMP AS DETERMINED BY THE DIRECTION OF MEDIA FLOW WITH RESPECT TO THE AXIS OF THE SHAFT.
Enter the applicable reply code from the table below
(AHZEDA)
| Table 1 |
| Reply Code (AA80) | Reply |
| A | AXIAL FLOW |
| C | MIXED FLOW |
| B | RADIAL FLOW |
AHZFACENTRIFUGAL PUMP IMPELLER QUANTITY
THE NUMBER OF IMPELLERS INCORPORATED IN THE CENTRIFUGAL PUMP.
Enter the numeric reply with a minimum of one digit.
(AHZFA10*)
AHZGDCENTRIFUGAL PUMP IMPELLER SUCTION TYPE
INDICATES THE TYPE OF SUCTION PRODUCED BY THE IMPELLER OF THE CENTRIFUGAL PUMP.
Enter the applicable reply code from the table below
(AHZGDB*;AHZGDC$$DC*)
| Table 1 |
| Reply Code (AF09) | Reply |
| B | DOUBLE |
| C | SINGLE |
AAYDASTAGE QUANTITY
THE NUMBER OF STAGES INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYDA10*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ACKL*DMEDIA FOR WHICH DESIGNED
THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACKLDCQ*;ACKLDAS$DFC*;ACKLDAS$$DFC*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AB | AIR |
| AC | ALCOHOL |
| DV | ALKALI SOLUTION |
| AF | AMMONIA |
| EN | BLEACHING LIQUIDS |
| EP | BRINE |
| AR | BUTANE |
| EQ | CALCIUM SALT SOLUTION |
| AS | CARBON DIOXIDE |
| BB | ETHYLENE GLYCOL |
| ER | FERROUS SULFATE |
| GX | FOAM |
| ES | FREON USE REFRIGERANT |
| AED | FUEL |
| HA | GLYCERINE |
| AEL | HYDRAULIC FLUID |
| BS | HYDROCARBON FUELS AND OILS |
| EU | HYDROCHLORIC ACID |
| BU | INGESTED LIQUIDS |
| FS | INSECTICIDES |
| DT | LIQUID |
| WD | LITHIUM BROMIDE |
| EV | METHANOL |
| LW | METHYLENE CHLORIDE |
| EW | NAPHTHA |
| CF | NITRIC ACID |
| CJ | NITROGEN, LIQUID |
| CL | OIL |
| CP | OXYGEN, LIQUID |
| EX | PHOTOGRAPHIC DEVELOPERS |
| CQ | PROPANE |
| EY | RADIOACTIVE LIQUIDS |
| FW | REFRIGERANTS |
| EZ | SEWAGE |
| FA | SODIUM HYDROXIDE |
| FB | SODIUM PHOSPHATE |
| FC | SULFURIC ACID |
| WC | WATER, DISTILLED |
| DH | WATER, FRESH |
| DL | WATER, SALT |
| EK | WATER, WASTE |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAKX*;CBBLDALA$$DAGJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AGJ | FUNGUS RESISTANT TREATMENT |
| AKX | INTEGRAL RELIEF VALVE |
| AKZ | SELF-PRIMING |
| ALA | SUBMERSIBLE |
IF STYLE/REPLY CODE(s) AF, AJ, AK, AL OR AM WERE ENTERED FOR MRC AHZP, YOU MUST ANSWER MRC (AHZQ)
AHZP*DVOLUME CONTROL TYPE
INDICATES THE TYPE OF DEVICE USED TO CONTROL THE OUTPUT OR CAPACITY OF AN ITEM.
Enter the applicable reply code from the table below
(AHZPDAL)
| Table 1 |
| Reply Code (AH83) | Reply |
| AF | HYDRAULIC CYLINDER |
| AM | PRESSURE COMPENSATION |
| AG | PUSH-PULL |
| AH | ROTARY |
| AJ | SERVO MOTOR |
| AK | SERVO PISTON |
| AL | SYNCHRO |
AHZQ*DCONTROL LOCATION
INDICATES THE LOCATION OF THE CONTROL ON THE ITEM.
Enter the applicable reply code from the table below
(AHZQDGL*;AHZQDEW$$DGK*)
| Table 1 |
| Reply Code (AE46) | Reply |
| EW | CENTER |
| GK | LEFT SIDE |
| GL | RIGHT SIDE |
AHZS*DOPERATION RELATIONSHIP DESIGN
AN INDICATION OF HOW THE ITEMS ARE DESIGNED TO OPERATE IN RELATION TO EACH OTHER.
Enter the applicable reply code from the table below
(AHZSDC)
| Table 1 |
| Reply Code (AF56) | Reply |
| B | ALTERNATE |
| C | INDEPENDENT |
| D | SIMULTANEOUS |
AENCAPUMP QUANTITY
THE NUMBER OF PUMPS INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AENCA10*)
IF YOU ANSWER MRC AAYT, YOU MUST ANSWER MRC (AAYU)
AAYT*AINTAKE CONNECTION QUANTITY
THE NUMBER OF INTAKE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYTA10*)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AAYU, YOU MUST ANSWER MRC (ASWT)
AAYU*DINTAKE CONNECTION TYPE
INDICATES THE TYPE OF INTAKE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYUDBC*;AAYUDAP$DAN*;AAYUDAP$$DAN*)
| Table 1 |
| Reply Code (AA84) | Reply |
| BG | BELL MOUTH |
| BH | BUTT WELD |
| BK | COMPRESSION TUBE |
| AQ | FLANGED |
| AB | FLARED TUBE |
| BJ | OCTAGON FLANGE |
| AD | OVAL FLANGE |
| BC | QUICK DISCONNECT |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AH | TRIANGULAR FLANGE |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
ASWT*JINTAKE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INTAKE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(ASWTJNH2.0*;ASWTJNH2.0$$JNH2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JF | UNJF |
| NS | UNS |
AAYVADISCHARGE CONNECTION QUANTITY
THE NUMBER OF DISCHARGE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYVA10*)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AAYW, YOU MUST ANSWER MRC (ASAZ)
AAYWDDISCHARGE CONNECTION TYPE
INDICATES THE TYPE OF DISCHARGE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYWDAN*;AAYWDBG$$DAL*)
| Table 1 |
| Reply Code (AA84) | Reply |
| BG | BELL MOUTH |
| BH | BUTT WELD |
| BK | COMPRESSION TUBE |
| AQ | FLANGED |
| AB | FLARED TUBE |
| BJ | OCTAGON FLANGE |
| AD | OVAL FLANGE |
| BC | QUICK DISCONNECT |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AL | THREADED EXTERNAL |
| AM | THREADED INTERNAL |
| AH | TRIANGULAR FLANGE |
| AN | UNTHREADED EXTERNAL |
| AP | UNTHREADED INTERNAL |
ASAZ*JDISCHARGE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE DISCHARGE CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(ASAZJBS2.0*;ASAZJBS2.0$$JBS2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JF | UNJF |
| NS | UNS |
IF STYLE/REPLY CODE(s) AD WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAXS and AAXH and CSYL and ACDC and ELEC and AMPS and AKNA and ADZC and BFMF)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAXH and CSYL and ADQX and AAYP)
IF STYLE/REPLY CODE(s) AH, AK, AP OR AQ WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAXH and CSYL and ADQX)
IF STYLE/REPLY CODE(s) AC, AE OR AF WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAXS and AAXH and CSYL)
AKDJ*DPRIME MOVER TYPE
INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT.
Enter the applicable reply code from the table below
(AKDJDAE)
| Table 1 |
| Reply Code (AG27) | Reply |
| AC | DIESEL ENGINE |
| AD | ELECTRIC MOTOR |
| AF | GAS TURBINE |
| AE | GASOLINE ENGINE |
| AH | HYDRAULIC MOTOR |
| AK | PNEUMATIC MOTOR |
| AL | STEAM ENGINE |
| AM | STEAM TURBINE |
| AP | WATER MOTOR |
| AQ | WATER TURBINE |
AAXS*DPRIME MOVER COOLING MEDIUM
THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE PRIME MOVER. USE MRC ACZV AND ISAC TO TABLE 0094
Enter the applicable reply code from the table below
(AAXSDCL*;AAXSDCP$$DWD*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AB | AIR |
| AC | ALCOHOL |
| DV | ALKALI SOLUTION |
| AF | AMMONIA |
| EN | BLEACHING LIQUIDS |
| EP | BRINE |
| AR | BUTANE |
| EQ | CALCIUM SALT SOLUTION |
| AS | CARBON DIOXIDE |
| BB | ETHYLENE GLYCOL |
| ER | FERROUS SULFATE |
| GX | FOAM |
| ES | FREON USE REFRIGERANT |
| AED | FUEL |
| HA | GLYCERINE |
| AEL | HYDRAULIC FLUID |
| BS | HYDROCARBON FUELS AND OILS |
| EU | HYDROCHLORIC ACID |
| BU | INGESTED LIQUIDS |
| FS | INSECTICIDES |
| DT | LIQUID |
| WD | LITHIUM BROMIDE |
| EV | METHANOL |
| LW | METHYLENE CHLORIDE |
| EW | NAPHTHA |
| CF | NITRIC ACID |
| CJ | NITROGEN, LIQUID |
| CL | OIL |
| CP | OXYGEN, LIQUID |
| EX | PHOTOGRAPHIC DEVELOPERS |
| CQ | PROPANE |
| EY | RADIOACTIVE LIQUIDS |
| FW | REFRIGERANTS |
| EZ | SEWAGE |
| FA | SODIUM HYDROXIDE |
| FB | SODIUM PHOSPHATE |
| FC | SULFURIC ACID |
| WC | WATER, DISTILLED |
| DH | WATER, FRESH |
| DL | WATER, SALT |
| EK | WATER, WASTE |
AAXH*APRIME MOVER QUANTITY
THE NUMBER OF PRIME MOVERS INCORPORATED IN THE UNIT.
Enter the numeric reply with a minimum of one digit.
(AAXHA10*)
CSYL*JPRIME MOVER POWER RATING
THE RATED POWER OF THE PRIME MOVER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYLJS2.0*)
| Table 1 |
| Reply Code (AC33) | Reply |
| H | HORSEPOWER |
| S | HORSEPOWER METRIC |
| L | KILOWATTS |
| W | WATTS |
IF STYLE/REPLY CODE(s) B OR D WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (FREQ and FAAZ)
ACDC*DCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDC)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| D | AC/DC |
| C | DC |
ELEC*BVOLTAGE IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ELECB2.0*;ELECB2.0$$BM2.0*)
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0*;FREQB2.0$$BM2.0*)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDC*;FAAZDB$$DA*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| E | SINGLE/THREE |
| C | THREE |
| B | TWO |
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0*;AMPSB2.0$$BM2.0*)
AKNA*DINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAH*;AKNADAE$$DAP*)
| Table 1 |
| Reply Code (AG85) | Reply |
| AH | FULLY INCLOSED |
| AE | OPEN |
| AP | PARTIALLY INCLOSED |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDAQ)
| Table 1 |
| Reply Code (AA65) | Reply |
| CR | DRIPPROOF |
| DQ | DUST-IGNITION PROOF |
| BW | EXPLOSION PROOF |
| GN | FUNGUS PROOF |
| DR | OILPROOF |
| CP | SPLASH PROOF |
| DS | SPLASHTIGHT |
| CK | SUBMERSIBLE |
| KM | VAPORPROOF |
| AQ | WATERPROOF |
| BX | WATERTIGHT |
ADQX*JPOWER DRIVE OPERATING PRESSURE
THE PRESSURE REQUIRED TO ACTUATE THE POWER DRIVEN UNIT. PLEASE USE MRC CQCN IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQXJC2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| C | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
AAYP*JEXHAUST PRESSURE
THE GAGE PRESSURE OF THE EXPANDED STEAM AFTER DRIVING THE PRIME MOVER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYPJB2.0*)
| Table 1 |
| Reply Code (AA95) | Reply |
| B | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
AAXX*DMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDBC)
| Table 1 |
| Reply Code (AA78) | Reply |
| BF | BASE |
| AAD | BRACKET |
| BH | CASTER |
| ABR | FLANGE |
| ABV | FOOT |
| BJ | FRAME |
| BK | FRAME W/CASTERS |
| BC | HAND TRUCK |
| AT | SKID |
| AV | TRAILER |
| ADG | UNTHREADED HOLE |
| AU | WHEEL |
| BB | WHEELBARROW |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AFJP*DSPECIAL HANDLING FEATURE
THAT UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(AFJPDE)
| Table 1 |
| Reply Code (AD43) | Reply |
| D | FLAMMABLE |
| E | FRAGILE |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
AHZK*AEND ITEM NAME
THE APPROVED ITEM NAME OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the alpha-numeric reply with a minimum of one character.
(AHZKAL0)
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAZA000*;PRMTDPTA000$DIRA000*;PRMTDPTA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPTA000R2.0*;PMWTJPTA000R2.0$$JPTA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAC2.0*;AJAFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAC2.0*;AJAGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAC2.0*;AJAHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFHR*DACCESSORY COMPONENTS
THE ADDITIONAL PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter the applicable reply code from the table below
(AFHRDAKX*;AFHRDAKZ$$DALA*)
| Table 1 |
| Reply Code (AE15) | Reply |
| AAG | ADJUSTABLE AUTOMATIC DISCHARGE CHECK VALVE |
| AAH | COMBINATION PRESSURE AND VACUUM GAGE |
| AKY | DISCHARGE HOSE W/QUICK DISCONNECT FITTING |
| AAJ | ELECTRIC POWER CABLE |
| AAK | FLOW RATE GAGE |
| AAL | FOAM PROPORTIONER VALVE |
| AAM | GATE VALVES |
| AKX | GO-NO GO GAGE |
| AAN | LIFTING AND TIE-DOWN PROVISIONS |
| ALA | NONAUTOMATIC NOZZLE |
| ALB | PRIME MOVER CONTROLLER |
| AAP | SUCTION CHECK VALVE |
| AKZ | SUCTION HOSE W/QUICK DISCONNECT FITTING |
| AAQ | THREE-WAY SELECTOR VALVE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDANA000*;SFTTDANA000$DANA000*;SFTTDANA000$$DANA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAA0)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
BFMF*DCOOLING METHOD
THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable reply code from the table below
(BFMFDAAJ)
| Table 1 |
| Reply Code (AN05) | Reply |
| AAB | AIR TO AIR COOLED |
| AAY | BLOWER COOLED |
| AAP | FORCED AIR |
| AAZ | PIPE VENTILATED |
| ABS | SELF VENTILATED |
| AAH | WATER COOLED |
| AAJ | WATER-AIR COOLED |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3HOUDFEA000*;MATT3HOUDFEA000$DPCA000*;MATT3HOUDFEA000$$DPCA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HUT | PUMP BASIC |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| CUB000 | COPPER ALLOY |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| NLA000 | NICKEL |
| PCA000 | PLASTIC |
| STA000 | STEEL |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information