Excludes:COLORIMETER, PHOTOELECTRIC.

FSC Information

6630	Chemical Analysis Instruments

Colloquial Information

No Colloquials assigned to this Approve Item Name at this time

Change List

MRC PDNB has been added

MRC ZZZP has been deleted

NAMEDITEM NAME

NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.

Enter the item name code.

(NAMED16886*)

ANEHDDESIGN DESIGNATION

THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER OR USE FOR WHICH THE ITEM IS INTENDED.

Enter the applicable reply code from the table below

(ANEHDBSY*;ANEHDAJK$DAJL*)

Table 1
	Reply Code (AJ50)	Reply
	AJK	ASTM
	BSY	BECKMAN
	AJL	DUB0SCQ
	AJM	LOVIBOND

AWPTDINCLINED DESIGN FEATURE

AN INDICATION OF WHETHER OR NOT AN INCLINED DESIGN FEATURE IS INCLUDED.

Enter the applicable reply code from the table below

(AWPTDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

AWPWDDIRECT READING FEATURE

AN INDICATION OF WHETHER OR NOT A DIRECT READING FEATURE IS INCLUDED.

Enter the applicable reply code from the table below

(AWPWDB)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ATZAACUP QUANTITY

THE NUMBER OF CUPS PROVIDED.

Enter the numeric reply with a minimum of one digit.

(ATZAA10*)

ATZB*JOPEN END INSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPEN END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ATZBJAB2.0*;ATZBJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATZC*JOPEN END OUTSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPEN END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ATZCJAA2.0*;ATZCJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATZD*JBOTTOM END OUTSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ATZDJAB2.0*;ATZDJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATZFDPLUNGER LOWER END BEVEL

AN INDICATION OF WHETHER OR NOT A PLUNGER LOWER END BEVEL IS INCLUDED.

Enter the applicable reply code from the table below

(ATZFDB)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ATZG*BBEVEL ANGLE IN DEG

THE ANGLE OF THE BEVEL,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(ATZGB2.0)

AWPXJPLUNGER OVERALL DIAMETER

A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A PLUNGER.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AWPXJAC2.0*;AWPXJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AWPYJPLUNGER LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF A PLUNGER,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AWPYJAC2.0*;AWPYJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATZHDPLUNGER CORRECT ALIGNMENT LOCATING PIN

AN INDICATION OF WHETHER OR NOT A PLUNGER CORRECT ALIGNMENT LOCATING PIN/S/ IS INCLUDED.

Enter the applicable reply code from the table below

(ATZHDB)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ATZJDMICRO ATTACHMENT

AN INDICATION OF WHETHER OR NOT A MICRO ATTACHMENT(S) IS INCLUDED.

Enter the applicable reply code from the table below

(ATZJDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ACDCDCURRENT TYPE

INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.

Enter the applicable reply code from the table below

(ACDCDD)

Table 1
	Reply Code (AB62)	Reply
	B	AC
	D	AC/DC
	C	DC

AHGFALAMPHOLDER QUANTITY

THE NUMBER OF LAMPHOLDERS INCLUDED ON THE ITEM.

Enter the numeric reply with a minimum of one digit.

(AHGFA10*)

AEWR*ALAMP QUANTITY

THE NUMBER OF LAMPS INCLUDED WITH THE ITEM.

Enter the numeric reply with a minimum of one digit.

(AEWRA10*)

AEWX*BLAMP VOLTAGE RATING IN VOLTS

THE VOLTAGE FOR WHICH THE LAMP IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AEWXB2.0)

AEWS*BLAMP WATTAGE RATING IN WATTS

THE RATED POWER THAT A LAMP CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AEWSB2.0)

AEWW*BLAMP CANDLEPOWER RATING IN FOOTCANDLES

THE CANDLEPOWER,OR MEASUREMENT OF LUMINOUS INTENSITY FOR WHICH THE LAMP IS RATED,EXPRESSED IN FOOTCANDLES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AEWWB2.0)

ATZQ*BLAMP LUMINOSITY IN LUMENS

THE MEASUREMENT OF LUMINOUS FLUX FOR WHICH THE LAMP IS RATED,EXPRESSED IN LUMENS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(ATZQB2.0)

AMPS*BCURRENT RATING IN AMPS

THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AMPSB2.0)

AEWT*LLAMP BULB SHAPE STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE LAMP BULB.

Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.

(AEWTL18)

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAF1489	1	DESIGNATION A
AAF1498	10	DESIGNATION PAR
AAF1499	11	DESIGNATION PAR
AAF1500	12	DESIGNATION PS
AAF1501	13	DESIGNATION R
AAF1502	14	DESIGNATION RP
AAF1503	15	DESIGNATION S
AAF1504	16	DESIGNATION S
AAF1505	17	DESIGNATION S
AAF1506	18	DESIGNATION T
AAF1507	19	DESIGNATION T
AAF1490	2	DESIGNATION B
AAF1508	20	DESIGNATION T
AAF1509	21	DESIGNATION T
AAF1510	22	DESIGNATION TL
AAF1511	23	DESIGNATION CYL
AAF1491	3	DESIGNATION B
AAF1492	4	DESIGNATION C
AAF1493	5	DESIGNATION F
AAF1494	6	DESIGNATION FE
AAF1495	7	DESIGNATION G
AAF1496	8	DESIGNATION GG
AAF1497	9	DESIGNATION P

AEWU*ALAMP BULB SIZE DESIGNATOR

THE DESIGNATION THAT DESCRIBES THE SIZE AND CONFIGURATION OF A LAMP BULB.

Enter the alpha-numeric reply with a minimum of one character.

(AEWUAL3)

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

AEWV*LLAMP BASE STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASE OF THE LAMP.

(AEWVL29)

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAF1386	1	MIDGET SCREW
AAF1394	10	DOUBLE CONTACT CANDELABRA PREFOCUS
DR02776	11	DOUBLE CONTACT BAYONET CANDELABRA SKIRTED
AAF1396	12	SLIDE
DR02777	13	DOUBLE CONTACT BAYONET CANDELABRA INDEXING
DR02788	14A	SINGLE PIN T-5
DR02789	14B	SINGLE PIN T-6
DR02790	14C	SINGLE PIN T-8
DR02791	14D	SINGLE PIN T-12
DR02778	15	MEDIUM BIPOST
DR02792	16A	MINIATURE BIPIN
DR02793	16B	MEDIUM BIPIN T-8
DR02794	16C	MEDIUM BIPIN T-12
DR02795	16D	MOGUL BIPIN
AAF1399	17	THREE CONTACT LUGS
DR02779	18	4-PIN
AAF1401	19	SCREW TERMINALS
AAF1387	2	MIDGET FLANGE
DR02780	20	MOGUL BIPOST
DR02796	21A	THREE CONTACT MEDIUM SCREW
DR02797	21B	THREE CONTACT MOGUL SCREW
DR02798	22A	MINIATURE SCREW
DR02799	22B	CANDELABRA SCREW
DR02800	22C	INTERMEDIATE SCREW
DR02801	22D	MEDIUM SCREW
DR02802	22E	ADMEDIUM SCREW
DR02803	22F	MOGUL SCREW
DR02804	23A	MEDIUM PREFOCUS
DR02805	23B	MOGUL PREFOCUS
DR02806	24A	SINGLE CONTACT CANDELABRA PINLESS
DR02807	24B	MINIATURE PINLESS
DR02808	25A	CANDELABRA SCREW SKIRTED
DR02809	25B	MEDIUM SCREW SKIRTED
DR02810	25C	ADMEDIUM SCREW SKIRTED
AAF1403	26	SPECIAL GUNSIGHT SCREW
DR02781	27	SPECIAL 952
AAF1440	28A	3 PRONG
AAF1441	28B	2 PRONG
AAF1405	29	SPECIAL INSTRUMENT SLIDE
DR02773	3	KOLLSMAN
AAF1406	30	MOUNTING LUGS AND BEADED WIRE LEADS
AAF1407	31	BRASS FERRULE
AAF1408	32	THREE CONTACT MEDIUM BAYONET
AAF1409	33	FLEXIBLE LEAD
AAF1410	34	DOUBLE CONTACT CANDELABRA PINLESS
AAF1411	35	DOUBLE INTERMEDIATE SCREW
AAF1412	36	SURGICAL FLANGE, STYLE 1
AAF1413	37	SURGICAL FLANGE, STYLE 2
AAF1414	38	SURGICAL SCREW
AAF1415	39	DOUBLE CONTACT MEDIUM RING
AAF1389	4	MINIATURE FLANGE
AAF1416	40	B AND H RING
AAF1417	41	SMALL INDEXING RING
AAF1418	42	LARGE INDEXING RING
AAF1419	43	VENTED LARGE INDEXING RING
AAF1442	44A	MOGUL END PRONG
AAF1443	44B	TWO CONTACT LUGS
AAF1420	45	MEDIUM SIDE PRONG
DR02782	46	GROOVED MIDGET
AAF1422	47	UNTHREADED CYLINDER WITH SCREW TERMINAL
DR02783	48	4-PIN INDEXING
DR02784	49	MINIATURE 2-PIN
AAF1390	5	DISK
AAF1425	50	BRASS FERRULE, STYLE 2
AAF1426	51	POLARIZED SUBMINIATURE BIPIN
AAF1427	52	TAB
DR02785	53	GLASS GROOVE
AAF1429	54	RECESSED SINGLE CONTACT
AAF1430	55	RECESSED DOUBLE CONTACT
DR02774	6	SINGLE CONTACT BAYONET CANDELABRA INDEXING
DR02786	7A	SINGLE CONTACT BAYONET CANDELABRA
DR02775	8	DOUBLE CONTACT BAYONET CANDELABRA
AAF1393	9	SINGLE CONTACT CANDELABRA PREFOCUS

AFAX*ALAMP INDUSTRY NUMBER

THE MEANS ESTABLISHED TO IDENTIFY THE LAMP BY AN INDUSTRY STANDARD NUMBER.

Enter the alpha-numeric reply with a minimum of one character.

(AFAXAM7)

AEWZ*DLAMP TRANSPARENCY

THE ABILITY OF THE LAMP OR PORTION OF THE LAMP TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION.

Enter the applicable reply code from the table below

(AEWZDAC)

Table 1
	Reply Code (AF93)	Reply
	AB	CLEAR
	AC	FROSTED

AWPZDCASE LOCKING DEVICE

AN INDICATION OF WHETHER OR NOT A CASE LOCKING DEVICE IS INCLUDED.

Enter the applicable reply code from the table below

(AWPZDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ATZRDINSCRIPTION

AN INDICATION OF WHETHER OR NOT AN INSCRIPTION IS INCLUDED.

Enter the applicable reply code from the table below

(ATZRDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

ATZS*GLEGEND INSCRIPTION

THE INSCRIPTION AFFIXED TO OR STAMPED ON THE ITEM,EXCLUDING THE PART NUMBER.

Enter clear text.

(ATZSGCLEARTEXT)

AKYN*GFURNISHED ITEMS AND QUANTITY

THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.

Enter clear text.

(AKYNGCLEARTEXT)

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH