Table 1
	Reply Code (AD07)	Reply
	AAB	A
	AHT	HORIZONTAL RECTANGULAR
	ALL	PARALLEL PIPED
	BKX	PLANE PARALLEL
	APL	ROUND
	BKZ	SLOPE
	ASF	SPIRAL
	ATG	STRAIGHT
	AYL	U-TUBE
	AYS	VERTICAL OVAL

CYLFDCOIL REFRIGERANT TYPE FOR WHICH DESIGNED

INDICATES THE TYPE REFRIGERANT THE COIL IS DESIGNED TO USE.

Enter the applicable reply code from the table below

(CYLFDAAC*;CYLFDAAB$DAAS*;CYLFDAAB$$DAAS*)

Table 1
	Reply Code (AB75)	Reply
	AAB	AIR
	AFE	FREON 12
	AAC	FRESH WATER
	AAE	REFRIGERANT
	AAS	REFRIGERANT R-12
	AAW	REFRIGERANT R-22
	AAF	SALT WATER

CYGNDTUBE MATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE TUBE IS FABRICATED.

Enter the applicable reply code from the table below

(CYGNDSTA000*;CYGNDAL0063$DSTB000*;CYGNDAL0063$$DSTB000*)

Table 1
	Reply Code (MA01)	Reply
	ALB000	ALUMINUM ALLOY
	AL0063	ALUMINUM ALLOY A332.0
	AL0002	ALUMINUM ALLOY A356.0
	CUA000	COPPER
	CUB000	COPPER ALLOY
	NLB000	NICKEL ALLOY
	PCA000	PLASTIC
	CLB000	PORCELAIN
	STA000	STEEL
	ST1009	STEEL COMP 1009
	ST0079	STEEL COMP 303SE
	STB000	STEEL CORROSION RESISTING
	ZNB000	ZINC
	ZNA000	ZINC ALLOY

CWQSJINLET NOMINAL INSIDE DIAMETER

THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CWQSJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

CWRCJINLET NOMINAL OUTSIDE DIAMETER

THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CWRCJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

CWRNJOUTLET NOMINAL INSIDE DIAMETER

THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CWRNJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

CWSDJOUTLET NOMINAL OUTSIDE DIAMETER

THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CWSDJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

BBJXDMOUNTING POSITION

THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED.

Enter the applicable reply code from the table below

(BBJXDAAF*;BBJXDAAP$DAAF*)

Table 1
	Reply Code (AM84)	Reply
	AAP	HORIZONTAL
	AAF	VERTICAL

CYLG*DFIN ARRANGEMENT TYPE

INDICATES THE TYPE ARRANGEMENT OF THE FINS ON THE ITEM.

Enter the applicable reply code from the table below

(CYLGDADM*;CYLGDADN$DADL*)

Table 1
	Reply Code (AK33)	Reply
	ADL	CONFIGURATED PLATE
	ADM	CRIMPED SPIRAL
	ADN	FLAT PLATE
	ADP	SMOOTH SPIRAL

CYLE*DFIN MATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FIN IS FABRICATED.

Enter the applicable reply code from the table below

(CYLEDST0079*;CYLEDCLB000$DPCA000*;CYLEDCLB000$$DPCA000*)

Table 1
	Reply Code (MA01)	Reply
	ALB000	ALUMINUM ALLOY
	AL0063	ALUMINUM ALLOY A332.0
	AL0002	ALUMINUM ALLOY A356.0
	CUA000	COPPER
	CUB000	COPPER ALLOY
	NLB000	NICKEL ALLOY
	PCA000	PLASTIC
	CLB000	PORCELAIN
	STA000	STEEL
	ST1009	STEEL COMP 1009
	ST0079	STEEL COMP 303SE
	STB000	STEEL CORROSION RESISTING
	ZNB000	ZINC
	ZNA000	ZINC ALLOY

SFTT*DSURFACE TREATMENT

THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.

Enter the applicable reply code from the table below

(SFTTDENE000*;SFTTDCRA000$DCMA000*;SFTTDCRA000$$DCMA000*)

Table 1
	Reply Code (SF01)	Reply
	CMA000	CHROMATE
	CRA000	CHROMIUM
	CUB000	COPPER ALLOY
	DCA000	DICHROMATE
	MSG000	ELECTROPLATED COPPER
	MSH000	ELECTROPLATED STEEL
	ENA000	ENAMEL
	END000	ENAMEL BAKED
	ENE000	ENAMEL GLOSS
	PBA000	LEAD
	PNA000	PAINT
	PHA000	PHOSPHATE

IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)

STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION

THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.

Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.

(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)

Table 1
	Reply Code (AP33)	Reply
	G	ASSN STD
	A	COMMERCIAL ITEM DESCRIPTION
	K	DEF STAN/SPEC
	B	FED SPEC
	C	FED STD
	L	GOVERNMENT STD/SPEC
	N	INTERNATIONAL STD/SPEC
	F	MFR REF
	D	MIL SPEC
	E	MIL STD
	H	NATIONAL SPEC
	P	NATIONAL STD
	M	NATIONAL STD/SPEC

Table 2
	Reply Code (AP39)	Reply
	M	10TH TREATMENT RESPONSE
	N	11TH TREATMENT RESPONSE
	P	12TH TREATMENT RESPONSE
	Q	13TH TREATMENT RESPONSE
	R	14TH TREATMENT RESPONSE
	S	15TH TREATMENT RESPONSE
	B	1ST TREATMENT RESPONSE
	C	2ND TREATMENT RESPONSE
	D	3RD TREATMENT RESPONSE
	E	4TH TREATMENT RESPONSE
	F	5TH TREATMENT RESPONSE
	H	6TH TREATMENT RESPONSE
	J	7TH TREATMENT RESPONSE
	K	8TH TREATMENT RESPONSE
	L	9TH TREATMENT RESPONSE
	G	ALL TREATMENT RESPONSES
	A	SINGLE TREATMENT RESPONSE

AAJU*JOVERALL LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAJUJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

AAJV*JOVERALL WIDTH

AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAJVJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

AAJT*JOVERALL HEIGHT

THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAJTJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

AWGF*JEFFECTIVE COOLING AREA

THE AMOUNT OF EFFECTIVE COOLING AREA.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AWGFJF2.0*)

Table 1
	Reply Code (AC51)	Reply
	F	SQUARE FEET
	M	SQUARE METERS

ADZC*DENVIRONMENTAL PROTECTION

THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.

Enter the applicable reply code from the table below

(ADZCDABX*;ADZCDADC$DAEF*;ADZCDADC$$DAEF*)

Table 1
	Reply Code (AA65)	Reply
	ABX	ABRASION RESISTANT
	ADC	AIRTIGHT
	AEP	ICE RESISTANT
	ABE	SHOCK RESISTANT
	AEF	STAIN RESISTANT
	ABJ	VIBRATION RESISTANT
	ABM	WEATHERPROOF

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDBLX*;CBBLDANN$$DAAB*)

Table 1
	Reply Code (AN47)	Reply
	ANN	AIR RELEASE VALVE
	ART	COOLANT HOLE
	CXX	COOLING FIN
	BLX	DRAIN PLUG
	AAB	ENDS SEALED FOR REFRIGERATION SERVICE
	CSD	MOUNTING ATTACHMENT
	ANX	THERMAL INSULATED
	CBK	VENTILATED
	EBB	VENTURI FLOW

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)