A mechanical device driven by vacuum to produce the necessary motion to operate a windshield wiper.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED15773*)
APHPDMANUAL OPERATION FACILITY
AN INDICATION OF WHETHER OR NOT A MANUAL OPERATION FACILITY IS PROVIDED.
Enter the applicable reply code from the table below
(APHPDB)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
BJYDJACTUATING SHAFT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ACTUATING SHAFT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BJYDJLC2.0*;BJYDJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BJYFJACTUATING SHAFT LARGEST DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF AN ACTUATING SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BJYFJAB2.0*;BJYFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) BDB WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (BJYB)
IF STYLE/REPLY CODE(s) BDC WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (AMWL)
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDBDB*;APGFDBDC$DBDC*)
| Table 1 |
| Reply Code (AK54) | Reply |
| BDB | OSCILLATING ARM |
| BDC | RECIPROCATING ARM |
BJYB*BTHROW ANGLE IN DEG
THE ANGLE OF THROW,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BJYBB2.0)
AMWL*JSTROKE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE STROKE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMWLJAA2.0*;AMWLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BHMQ, YOU MUST ANSWER MRC (ASHM and AYDZ)
BHMQDCONTROL VALVE
AN INDICATION OF WHETHER OR NOT A CONTROL VALVE IS PROVIDED.
Enter the applicable reply code from the table below
(BHMQDC)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
ASHM*DVALVE TYPE
INDICATES THE TYPE OF VALVE.
Enter the applicable reply code from the table below
(ASHMDAJ)
| Table 1 |
| Reply Code (AL80) | Reply |
| AJ | INTEGRAL |
| AK | SEPARABLE |
AYDZ*DSPEED TYPE
INDICATES THE TYPE OF SPEED FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AYDZDAB)
| Table 1 |
| Reply Code (AL77) | Reply |
| AB | CONSTANT |
| AG | VARIABLE |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BJYC, YOU MUST ANSWER MRC (ABHE) or (ARFH and ANKC and BPHG and ARFJ)
IF STYLE/REPLY CODE(s) C WERE ENTERED FOR MRC BJYC, YOU MUST ANSWER MRC (BNPL) or (ARFH and ANKC and BPHG and ARFJ)
BJYCDCONNECTION FITTING
AN INDICATION OF WHETHER OR NOT A CONNECTION FITTING IS INCLUDED.
Enter the applicable reply code from the table below
(BJYCDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ABHE*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHEJLB2.0*;ABHEJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BNPL*JCONNECTION INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BNPLJAA2.0*;BNPLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARFH*DCONNECTION THREAD LOCATION
INDICATES THE LOCATION OF THE THREADS ON THE CONNECTION.
Enter the applicable reply code from the table below
(ARFHDABX)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
ANKC*ACONNECTION THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CONNECTION.
Enter the alpha-numeric reply with a minimum of one character.
(ANKCAQ0)
BPHG*DCONNECTION THREAD SERIES DESIGNATOR
A DESIGNATOR INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE THREADED CONNECTION.
Enter the applicable reply code from the table below
(BPHGDBX*;BPHGDNT$DSS*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| BX | NC |
| NQ | NEF |
| BY | NF |
| CB | NF-1 |
| CC | NF-2 |
| SF | NPSF |
| NP | NPT |
| NT | NPTF |
| AQ | NS |
| SJ | SI |
| SK | SI-M |
| NF | UNF |
ARFJ*DCONNECTION THREAD DIRECTION
THE DIRECTION OF THE CONNECTION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ARFJDR)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
IF STYLE/REPLY CODE(s) FQ WERE ENTERED FOR MRC BJYG, YOU MUST ANSWER MRC (AAUB and BFHF)
IF STYLE/REPLY CODE(s) FR WERE ENTERED FOR MRC BJYG, YOU MUST ANSWER MRC (ASMM)
IF STYLE/REPLY CODE(s) FS WERE ENTERED FOR MRC BJYG, YOU MUST ANSWER MRC (BJYH)
IF STYLE/REPLY CODE(s) BG WERE ENTERED FOR MRC BJYG, YOU MUST ANSWER MRC (AGVN and AJYY and AKAF and AKAL)
BJYGDACTUATING SHAFT END CONNECTION TYPE
INDICATES THE TYPE OF END CONNECTION PROVIDED ON THE ACTUATING SHAFT.
Enter the applicable reply code from the table below
(BJYGDFS*;BJYGDFR$DBG*;BJYGDFR$$DBG*)
| Table 1 |
| Reply Code (AB76) | Reply |
| FQ | DRILLED |
| FR | PIVOT ARM |
| FS | SERRATED |
| BG | THREADED |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJLC2.0*;AAUBJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFHF*JDISTANCE FROM SHAFT HOLE CENTER TO END
THE DISTANCE FROM THE SHAFT HOLE CENTER TO THE END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFHFJLC2.0*;BFHFJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASMM*ACONNECTION QUANTITY
THE NUMBER OF CONNECTIONS FURNISHED.
Enter the numeric reply with a minimum of one digit.
(ASMMA10*)
BJYH*DSERRATION SHAPE
THE PHYSICAL CONFIGURATION OF THE SERRATIONS.
Enter the applicable reply code from the table below
(BJYHDBK)
| Table 1 |
| Reply Code (AD07) | Reply |
| BK | STRAIGHT |
| TA | TAPERED |
AGVN*ASHAFT THREAD SIZE
DESIGNATES THE SHAFT THREAD DIAMETER AND NUMBER OF THREADS PER INCH.
Enter the alpha-numeric reply with a minimum of one character.
(AGVNAF3)
AJYY*DSHAFT THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SHAFT THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(AJYYDSK*;AJYYDNF$DSJ*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| AQ | NS |
| SJ | SI |
| SK | SI-M |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
AKAF*DSHAFT THREAD DIRECTION
THE DIRECTION OF THE SHAFT THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AKAFDR)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
AKAL*JSHAFT SCREW THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF SHAFT SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKALJLA2.0*;AKALJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) ABC WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (ABTJ and ABTB and BJYJ)
IF STYLE/REPLY CODE(s) AYM WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AJSE and AMCA and BJYL and BJYM and BJYN)
AXGYDMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDABW*;AXGYDAJR$DAAE*;AXGYDAJR$$DAAE*)
| Table 1 |
| Reply Code (AM39) | Reply |
| AAC | BOLT |
| ABC | BRACKET |
| AGG | HOOK |
| BGA | NUT |
| ABW | SCREW |
| AJR | STRUT |
| AAE | STUD |
| AYM | THREADED SLEEVE |
| BPF | WASHER |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJLA2.0*;ABTBJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BJYN*DSLEEVE THREAD DIRECTION
THE DIRECTION OF THE SLEEVE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(BJYNDL)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
BJYM*DSLEEVE THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATIONS APPLIED TO A SLEEVE.
Enter the applicable reply code from the table below
(BJYMDSK*;BJYMDSM$DSJ*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| AQ | NS |
| SJ | SI |
| SK | SI-M |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
BJYL*ASLEEVE THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED SLEEVE.
Enter the alpha-numeric reply with a minimum of one character.
(BJYLAA7)
AMCA*JSLEEVE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLEEVE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMCAJAB2.0*;AMCAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJSE*JSLEEVE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SLEEVE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJSEJLB2.0*;AJSEJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BJYJ, YOU MUST ANSWER MRC (AQPN and BJYK and ACJC)
BJYJ*DMOUNTING HOLE THREAD PROVISION
AN INDICATION OF WHETHER OR NOT THE MOUNTING HOLE IS THREADED.
Enter the applicable reply code from the table below
(BJYJDB)
| Table 1 |
| Reply Code (AE00) | Reply |
| B | THREADED |
| C | UNTHREADED |
AQPN*AMOUNTING HOLE THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A MOUNTING HOLE.
Enter the alpha-numeric reply with a minimum of one character.
(AQPNAC2)
BJYK*DMOUNTING HOLE THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATIONS APPLIED TO A MOUNTING HOLE.
Enter the applicable reply code from the table below
(BJYKDNC*;BJYKDSK$DSM*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| AQ | NS |
| SJ | SI |
| SK | SI-M |
| NC | UNC |
| NF | UNF |
ACJC*DMOUNTING HOLE THREAD DIRECTION
THE DIRECTION OF THE MOUNTING HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACJCDR)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ALXY*GMOUNTING HOLE SPACING
THE SPACING BETWEEN THE MOUNTING HOLES.
Enter clear text.
(ALXYGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information