FSC Information

6515	Medical and Surgical Instruments, Equipment, and Supplies

Colloquial Information

No Colloquials assigned to this Approve Item Name at this time

Change List

MRC CPMD has been deleted

NAMEDITEM NAME

NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.

Enter the item name code.

(NAMED14238*)

AZCJ*AINDIVIDUAL MOTOR QUANTITY

THE NUMBER OF INDIVIDUAL MOTORS PROVIDED.

Enter the numeric reply with a minimum of one digit.

(AZCJA10*)

AZKJ*DMOTOR CURRENT TYPE

INDICATES THE TYPE OF CURRENT REQUIRED TO OPERATE THE MOTOR.

Enter the applicable reply code from the table below

(AZKJDC*;AZKJDB$$DB*)

Table 1
	Reply Code (AB62)	Reply
	B	AC
	C	DC

AZKK*BMOTOR VOLTAGE IN VOLTS

THE TOTAL ELECTRICAL VOLTAGE OF THE MOTOR,EXPRESSED IN VOLTS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AZKKB2.0*;AZKKB2.0$BM2.0;AZKKB2.0$$BM2.0*)

ACDC*DCURRENT TYPE

INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.

Enter the applicable reply code from the table below

(ACDCDB*;ACDCDC$DC*)

Table 1
	Reply Code (AB62)	Reply
	B	AC
	C	DC

AMSE*JVOLTAGE RATING

THE VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AMSEJVA2.0*;AMSEJVA2.0$JVA2.0*;AMSEJVA2.0$$JVA2.1*)

Table 1
	Reply Code (AB63)	Reply
	K	KILOVOLTS
	V	VOLTS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABJL*BWATTAGE RATING IN WATTS

THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(ABJLB2.0)

ASQQ*BHORSEPOWER RATING

THE RATED HORSEPOWER OF THE ITEM. PLEASE USE MRC ANCY IN PLACE OF THIS DISCONTINUED MRC.

Enter a reply with a minimum of one digit on either side of the decimal point.

(ASQQB2.0)

BRXN*DHEAT TRANSFER METHOD

THE MEANS BY WHICH THE HEAT IS TRANSFERRED.

Enter the applicable reply code from the table below

(BRXNDAY*;BRXNDAZ$DAT*)

Table 1
	Reply Code (AK43)	Reply
	AT	BOILING WATER
	AW	DRY HEAT
	AX	FLOWING STEAM
	AY	HOT OIL
	AZ	PRESSURE STEAM

BDWT*DHEATING METHOD

THE MEANS BY WHICH THE ITEM IS HEATED.

Enter the applicable reply code from the table below

(BDWTDBJ*;BDWTDAH$DAB*;BDWTDAH$$DAB*)

Table 1
	Reply Code (AM63)	Reply
	AB	ELECTRICAL
	BM	EXTERNAL HEAT
	BJ	FUEL
	AG	GAS
	BN	GASOLINE BURNER
	AH	STEAM FROM REMOTE STEAM SOURCE

ABKW*JOVERALL HEIGHT

THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABHP*JOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABMK*JOVERALL WIDTH

AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGZL*ASHELF QUANTITY

THE NUMBER OF SHELVES FURNISHED WITH THE ITEM.

Enter the numeric reply with a minimum of one digit.

(BGZLA10*)

AAXX*DMOUNTING TYPE

INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.

Enter the applicable reply code from the table below

(AAXXDAABM*;AAXXDAACH$$DAACF*)

Table 1
	Reply Code (AA78)	Reply
	AACX	ADJUSTABLE LEGS
	A	ANY ACCEPTABLE
	AACZ	BASE
	AACY	BUTTONS
	AABR	CABINET
	AABT	CASTER
	AABW	CRUTCH TIPS
	AABN	DESK
	AABX	DOOR
	AABY	DRESSING CART
	ABP	FEET
	AABZ	FLOOR
	AACT	FOUR FEET
	AACW	FOUR MOLDED PLASTIC FEET
	AACA	GLIDE
	AACH	HOUSING BASE RUBBER FEET
	AACB	LEGS
	AACC	NONHEAT CONDUCTIVE FEET
	AACD	PEDESTAL
	AACE	PORTABLE STAND
	AABS	RECESSED CABINET
	AACF	RECTANGULAR BASE
	AACG	REMOVABLE LEGS
	AACJ	RUNNERS
	AACK	SHIPPING CASE
	AABP	STAND
	AACM	STANDARD OPERATING TABLE
	AACN	SUPPORTING FRAME
	AACP	SWIVEL CASTERS
	AACQ	TABLE
	AACR	TUBULAR STAND
	AABQ	WALL
	AACL	WALL BRACKET
	AACS	WALL RECESSED
	AABM	WHEEL

ADJT*JINSIDE WIDTH

AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADJTJAA2.0*;ADJTJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADJU*JINSIDE LENGTH

A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADJUJAC2.0*;ADJUJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AFMQ*JINSIDE HEIGHT

AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM,IN DISTINCTION FROM DEPTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AFMQJAA2.0*;AFMQJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AARX*JINSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AARXJAC2.0*;AARXJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BJHJ*ACASTER QUANTITY

THE NUMBER OF CASTERS PROVIDED ON THE ITEM.

Enter the numeric reply with a minimum of one digit.

(BJHJA10*)

ANEX*ACARRYING CASE QUANTITY

THE NUMBER OF CARRYING CASES INCLUDED.

Enter the numeric reply with a minimum of one digit.

(ANEXA10*)

AKYD*GACCESSORY COMPONENTS AND QUANTITY

THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.

Enter clear text.

(AKYDGCLEARTEXT)

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDETF*;CBBLDAQE$DCTD*;CBBLDAQE$$DCTD*)

Table 1
	Reply Code (AN47)	Reply
	ASQ	ADJUSTABLE
	ESX	AIR TUBE
	BHQ	AUTOCLAVABLE
	CSF	AXLE FRONT/REAR WHEEL
	CSG	BED END ACCESSORY SOCKET
	CSH	BED END ADJUSTABLE LEGS
	CZK	BICYCLE FRONT/REAR WHEEL
	BVM	BLOOD/OIL IMPERVIOUS
	DLM	BRAKING
	AMP	CASE
	CKV	CATCH LOCK CLOSURE FASTENER
	ESZ	CHAMBER
	BUV	CONDUCTIVE
	DLN	CRANK SPRING ELEVATING
	CTC	CUP
	ETG	CUSHION FRONT/REAR TIRE
	ETA	CYLINDRICAL
	DMS	DISK FRONT/REAR WHEEL
	AQE	DISPOSABLE
	DMT	ELECTRIC LEG
	CFU	END
	EES	END TAPER TO ACCOMMODATE TIP
	ATH	FIXED
	DRM	FOLDING LEG
	CFV	HAND
	DMU	HAND SPRING ELEVATING
	CRV	HOOK AND PILE CLOSURE
	CRU	HOOK-ON CUFF
	BCG	INDIVIDUALLY SEALED
	DMV	LEVER SPRING ELEVATING
	CTD	LID
	DRN	LOWER SHELF
	DMW	MANUAL LEG
	ETB	MANUAL OPERATION
	EYU	MEETS/EXCEEDS AFFIRMATIVE PROCUREMENT PROGRAM REQUIREMENTS
	CEV	NONALLERGENIC/NONTOXIC
	BVL	NONCONDUCTIVE
	AQP	NONSTERILE
	CGU	ORAL
	CGV	OVULATION
	BMQ	PERFORATION
	DMX	PNEUMATIC TIRE
	EHB	POCKET
	CHU	RECTAL
	ETC	RECTANGULAR
	DWW	RECTANGULAR TUBULAR BED END
	AQS	REUSABLE
	ELV	ROUND TUBULAR BED END
	CDU	SIDE
	BVT	SLIDE FASTENER CLOSURE
	CDV	SLIDING
	CHV	SNAP CATCH FASTENER CLOSURE
	ESP	SOLID FRONT/REAR TIRE
	ESQ	SOLID TIRE
	ESR	SPRING MATTRESS RETAINER
	ESS	SQUARE TUBULAR BED END
	EST	STATIONARY BED END CASTER
	AFM	STERILE
	ESY	SUSPENSION BAIL
	ESU	SWIVEL BED END CASTER
	ESV	SWIVEL CASTER FRONT/REAR WHEEL MOUNTING
	ESW	SWIVEL YOKE FRONT/REAR WHEEL MOUNTING
	CEU	TABLE TOP GUARD RAIL
	ADW	TAMPER PROOF CAP
	ETD	TANK
	ETE	TILTING-ROTATING UNIT
	ETF	TRANSFORMER/RECTIFIER
	CJU	TUBERCULAR
	BYZ	W/RESET
	CJV	WRAPAROUND SLEEVE
	CKU	ZIPPER CLOSURE

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ENAC*DENVIRONMENTAL ATTRIBUTE CODE

INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.

Enter the applicable reply code from the table below

(ENACDJH)

Table 1
	Reply Code (EN02)	Reply
	JH	COMPREHENSIVE PROCUREMENT GUIDELINE - PAPER AND PAPER PRODUCTS - MISCELLANEOUS PAPERS
	JL	COMPREHENSIVE PROCUREMENT GUIDELINE - PAPER AND PAPER PRODUCTS - PRINTING AND WRITING PAPERS

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)