A container usually made of duck cloth or other flexible material suitable for carrying drinking and cooking water. It may have a spout faucet and a carrying handle(s) or shoulder strap. Excludes:BAG, DRINKING WATER STORAGE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED11488*)
ARQTDOPENING LOCATION
THE LOCATION OF THE OPENING ON THE ITEM.
Enter the applicable reply code from the table below
(ARQTDAJD*;ARQTDDNF$$DABA*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| AJD | ALONG VERTICAL CORNER |
| ABA | BOTTOM |
| AJB | CENTER FRONT PANEL |
| AJC | CENTER SIDE PANEL |
| DNF | ENDS |
| AHL | ONE END |
| ADD | ONE SIDE |
| ABD | TOP |
IF STYLE/REPLY CODE(s) A1 OR A3 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and AQPL and ARRR)
IF STYLE/REPLY CODE(s) A2 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and AQPL and ARRS)
IF STYLE/REPLY CODE(s) A4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and AQPL)
IF STYLE/REPLY CODE(s) A5, A12 OR A15 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABFY and ABKW and ABMK)
IF STYLE/REPLY CODE(s) A6, A7, A8, A9, A20, A21, A30 OR A33 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABMK)
IF STYLE/REPLY CODE(s) A10 OR A26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ADAV)
IF STYLE/REPLY CODE(s) A13 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAV)
IF STYLE/REPLY CODE(s) A14 OR A25 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) A16, A17, A24 OR A35 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADJT and AFEF and AFMQ)
IF STYLE/REPLY CODE(s) A18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABFY and ABKW and ABMK)
IF STYLE/REPLY CODE(s) A19, A32 OR A34 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW)
IF STYLE/REPLY CODE(s) A22 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADJT and AJRL)
IF STYLE/REPLY CODE(s) A23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADJT and ADJU and AFMQ)
IF STYLE/REPLY CODE(s) A27 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABMK and ARRT)
IF STYLE/REPLY CODE(s) A28 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK)
IF STYLE/REPLY CODE(s) A29 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ARRR and ARRW)
IF STYLE/REPLY CODE(s) A31 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ARRR and ARRW)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA14)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAM1529 | A1 | SELF-OPENING/AUTOMATIC |
| AAM1538 | A10 | CYLINDRICAL |
| AAM1539 | A12 | RECTANGULAR |
| AAM1540 | A13 | UTILITY CYLINDRICAL |
| AAM1541 | A14 | UTILITY-SQUARE |
| AAM1542 | A15 | EQUIPMENT W/FORMED ATTACHED COVER |
| AAM1543 | A16 | EQUIPMENT W/ATTACHED FLAP |
| AAM1544 | A17 | EQUIPMENT W/FORMED DETACHABLE COVER |
| AAM1545 | A18 | EQUIPMENT |
| AAM1546 | A19 | EQUIPMENT |
| AAM1530 | A2 | SQUARE |
| AAM1547 | A20 | EQUIPMENT |
| AAM1548 | A21 | EQUIPMENT |
| AAM1549 | A22 | EQUIPMENT |
| AAM1550 | A23 | CARGO |
| AAM1551 | A24 | EQUIPMENT |
| AAM1552 | A25 | EQUIPMENT |
| AAM1553 | A26 | STORAGE |
| AAM1554 | A27 | STORAGE |
| AAM1555 | A28 | TRIANGULAR |
| AAM1556 | A29 | TRAPEZOID |
| AAM1531 | A3 | SATCHEL BOTTOM |
| AAM1557 | A30 | EQUIPMENT |
| AAM1558 | A31 | EQUIPMENT |
| AAM1559 | A32 | EQUIPMENT |
| AAM1560 | A33 | FLAT WITH ZIPLOCK CLOSURE |
| DQ00423 | A34 | EXTRACTION COLLAR |
| DQ00919 | A35 | HANDLING |
| AAM1532 | A4 | FLAT |
| AAM1533 | A5 | PROTECTIVE |
| AAM1534 | A6 | PROTECTIVE |
| AAM1535 | A7 | FLAT W/TAG |
| AAM1536 | A8 | PROTECTIVE |
| AAM1537 | A9 | FLAT TUBULAR |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAA2.0*;ABFYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAA2.0*;ADAVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJT*JINSIDE WIDTH
AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJTJAC2.0*;ADJTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJU*JINSIDE LENGTH
A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJUJAB2.0*;ADJUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFEF*JINSIDE DEPTH
AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFEFJAA2.0*;AFEFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFMQ*JINSIDE HEIGHT
AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFMQJAB2.0*;AFMQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJRL*JMINOR INSIDE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJRLJAA2.0*;AJRLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AQPL*JFACE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AQPLJAB2.0*;AQPLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARRR*JBOTTOM WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRRJAC2.0*;ARRRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARRS*JGUSSET WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRSJAA2.0*;ARRSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARRT*JNECK OPENING WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRTJAC2.0*;ARRTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARRW*JTOP WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE TOP TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRWJAB2.0*;ARRWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARRE*JNOMINAL TEXTILE WEIGHT AND LOCATION
THE NOMINAL WEIGHT OF THE TEXTILE AND ITS LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARREJAGAJA2.0*;ARREJAGAJA2.0$$JAGAJA2.1*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AP | GRAMS PER SQUARE METER |
| AG | OUNCES PER SQUARE YARD |
| Table 2 |
| Reply Code (AJ91) | Reply |
| AJA | CUSHIONING |
| AHY | FIFTH WALL |
| AHS | FIRST WALL |
| AHX | FOURTH WALL |
| AHT | SECOND WALL |
| AHR | SINGLE WALL |
| AHZ | SIXTH WALL |
| AHW | THIRD WALL |
ARRF*JNOMINAL MATERIAL THICKNESS AND LOCATION
THE NOMINAL MEASUREMENT BETWEEN TWO PLANE SURFACES OF THE MATERIAL AS DISTINGUISHED FROM LENGTH OR WIDTH,AND ITS LOCATION. PLEASE USE MRC AAVY WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRFJLAHY2.0*;ARRFJLAHY2.0$$JLAHY2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AJ91) | Reply |
| AJA | CUSHIONING |
| AHY | FIFTH WALL |
| AHS | FIRST WALL |
| AHX | FOURTH WALL |
| AHT | SECOND WALL |
| AHR | SINGLE WALL |
| AHZ | SIXTH WALL |
| AHW | THIRD WALL |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDBU*;ADZCDAB$$DND*)
| Table 1 |
| Reply Code (AA65) | Reply |
| AA | ABRASION RESISTANT |
| AB | ACID RESISTANT |
| JL | ANTISTATIC TREATED |
| WD | BACTERIA RESISTANT |
| ND | DUST RESISTANT |
| BB | FIRE RESISTANT |
| AD | FIRE RETARDANT |
| GP | FUNGUS RESISTANT |
| BU | GREASE |
| BD | HIGH TEMPERATURE |
| GR | HUMIDITY RESISTANT |
| NS | HYDROSTATIC RESISTANT |
| GF | INSECT PROOF |
| WE | LEAK RESISTANT |
| AS | LOW TEMPERATURE |
| AJ | MILDEW RESISTANT |
| AAW | MOISTURE RESISTANT |
| DH | ODOR |
| AK | OIL RESISTANT |
| AFZ | PUNCTURE RESISTANT |
| AEN | TEAR RESISTANT |
| FM | TEMPERATURE RESISTANT |
| BQ | VAPOR |
| DZ | WATER REPELLENT |
| BS | WATER RESISTANT |
| AQ | WATERPROOF |
| BT | WEATHER RESISTANT |
ARRH*JLIQUID CAPACITY
THE VALUE WHICH REFLECTS THE AMOUNT OF LIQUID THE ITEM IS DESIGNED TO ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARRHJC2.0*)
| Table 1 |
| Reply Code (AB10) | Reply |
| L | LITERS |
| U | OUNCES |
| C | PINTS |
ARRJ*JHANDLING DEVICE AND QUANTITY
THE PROVISION(S) INCLUDED IN THE DESIGN OF THE ITEM TO FACILITATE CARRYING,TRANSPORTING,OR LIFTING AND THE NUMBER OF EACH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ARRJJAT2*;ARRJJAT2$$JAT3*)
| Table 1 |
| Reply Code (AD28) | Reply |
| BW | BECKET |
| DS | D-RING |
| DP | D-RING W/TAB |
| BY | HANDLE |
| DT | HOOK |
| BX | LOOP |
| BZ | ROPE |
| AK | SHOULDER STRAP |
| DQ | SLIDE LOCK KEEPER |
| AT | SLING |
| DR | SNAP HOOK |
| BS | STRAP |
ACSY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. PLEASE USE MRC TMQY IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ACSYJVR2*;ACSYJVR2$$JVR3*)
| Table 1 |
| Reply Code (AB87) | Reply |
| ZQ | ADAPTER, CATHETER |
| VZ | BOTTOM PAD |
| LD | CAP PLUG OUTLET |
| LE | CLAIM CHECK TAG |
| LF | COLLECTING TUBE |
| LM | COMBINATION PADLOCK |
| CP | COVER |
| VT | DRAIN ASSEMBLY |
| LG | FAUCETS |
| LH | FILLER NOZZLES W/PLUGS |
| VR | HOOD OVERFLOW OUTLET |
| LJ | HUMIDITY INDICATOR |
| VS | INPUT ASSEMBLY |
| LK | INSERTS |
| LL | INTERNAL BOTTOM PAD |
| CT | SCREW |
| LN | STERILIZATION INDICATOR |
| PS | STOPPER |
| LP | THREADED PLUG OUTLET |
| VW | TOP OPENING OUTLET |
| VY | TUBE |
| VV | TUBE OUTLET |
| VX | TUBE SHUT-OFF CLAMP |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
IF STYLE/REPLY CODE(s) BQ OR BV WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (ALAX)
IF STYLE/REPLY CODE(s) E7, E8 OR JL WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (PPRM)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDE7*;ENACDBQ$$DBV*)
| Table 1 |
| Reply Code (EN02) | Reply |
| E8 | COMPREHENSIVE PROCUREMENT GUIDELINE - NON-PAPER OFFICE PRODUCTS - PLASTIC ENVELOPES |
| E7 | COMPREHENSIVE PROCUREMENT GUIDELINE - NON-PAPER OFFICE PRODUCTS - PLASTIC TRASH BAGS |
| JK | COMPREHENSIVE PROCUREMENT GUIDELINE - PAPER AND PAPER PRODUCTS - PAPERBOARD AND PACKAGING PRODUCTS |
| JL | COMPREHENSIVE PROCUREMENT GUIDELINE - PAPER AND PAPER PRODUCTS - PRINTING AND WRITING PAPERS |
| BQ | FILMS - NON-DURABLE - BIOBASED |
| BV | FILMS - SEMI-DURABLE - BIOBASED |
ALAX*BBIOBASED CONTENT PERCENTAGE
THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALAXB2.0)
PPRM*BPOST-CONSUMER RECOVERED MATERIALS PERCENTAGE
THE PERCENTAGE OF THE POST-CONSUMER RECOVERED OR RECYCLED MATERIAL INCLUDED IN THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(PPRMB2.0)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAE*;BBRGDAC$DAJ*;BBRGDAC$$DAJ*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
AFJL*DFUMIGATION
AN INDICATION OF WHETHER OR NOT AN ITEM IN STORAGE REQUIRES EXPOSURE TO THE ACTION OF FUMES FOR THE PURPOSE OF DISINFECTION.
Enter the applicable reply code from the table below
(AFJLDC)
| Table 1 |
| Reply Code (AE40) | Reply |
| C | NOT REQUIRED |
| B | REQUIRED |
ARRQ*ACOMMERCIAL SIZE
THE SIZE BY WHICH THE ITEM IS COMMERCIALLY RECOGNIZED.
Enter the alpha-numeric reply with a minimum of one character.
(ARRQAK8)
AFJE*GSPECIFIC EQUIPMENT ACCOMMODATED
THE NAME OF THE EQUIPMENT THE ITEM IS SPECIFICALLY DESIGNED TO ACCOMMODATE.
Enter clear text.
(AFJEGCLEARTEXT)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3BASDPCAC00*;MATT3BASDPCAC00$DRCB000*;MATT3BASDPCAC00$$DRCB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3BAS | SINGLE WALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| CSA000 | CELLULOSE |
| CCA000 | COTTON |
| PCP000 | PLASTIC POLYAMIDE |
| PCX000 | PLASTIC POLYETHYLENE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| PCAP00 | PLASTIC VINYL |
| RCE000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CN | CUBIC INCHES |
ASBC*JNOMINAL BASIS WEIGHT
THE NOMINAL WEIGHT BASED ON A SPECIFIED AMOUNT,SIZE,OR THE LIKE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASBCJAAK2.0*)
| Table 1 |
| Reply Code (AL62) | Reply |
| AAK | GRAMS PER SQUARE METER |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information