A device designed to prevent foreign particles from entering the air intake system of an internal combustion engine or air compressor. Excludes:mufflers.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED10118*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDZNB000*;MATTDPCP000$DFBX000*;MATTDPCP000$$DFBX000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| FBX000 | FELT |
| GSA000 | GLASS |
| FEG000 | IRON WROUGHT |
| AAA044 | LAMINATED PLASTIC |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCDL00 | PLASTIC POLYAMIDE GLASS FILLED |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| STA000 | STEEL |
| ZSC000 | STEEL ALLOY |
| ST1020 | STEEL COMP 1020 |
| ST0321 | STEEL COMP 321 |
| STB000 | STEEL CORROSION RESISTING |
| ZNB000 | ZINC |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) AG WERE ENTERED FOR MRC ALTR, YOU MUST ANSWER MRC (ALGJ)
ALTRDFILTER TYPE
INDICATES THE TYPE OF FILTER USED WITH THE ITEM.
Enter the applicable reply code from the table below
(ALTRDAF)
| Table 1 |
| Reply Code (AH81) | Reply |
| AF | DRY |
| AG | OIL BATH |
| AH | OIL WETTED |
ALGJ*JOIL CAPACITY
THE VOLUME OF OIL THE ITEM WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALGJJBS2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BS | CENTILITER |
| AN | OUNCES |
| AR | PINTS |
ARYEDPRESSURE RELIEF VALVE
AN INDICATION OF WHETHER OR NOT A PRESSURE RELIEF VALVE IS INCLUDED.
Enter the applicable reply code from the table below
(ARYEDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ARTJGOUTLET LOCATION
THE LOCATION OF THE OUTLET.
Enter clear text.
(ARTJGCLEARTEXT)
ARYFDBACKFIRE VALVE
AN INDICATION OF WHETHER OR NOT A BACKFIRE VALVE IS INCLUDED.
Enter the applicable reply code from the table below
(ARYFDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) AB WERE ENTERED FOR MRC ARYG, YOU MUST ANSWER MRC (ARYH and ARYT and AMCA and ARYW) or (ARYH and ARYT and AMCA and ARYX)
IF STYLE/REPLY CODE(s) AE WERE ENTERED FOR MRC ARYG, YOU MUST ANSWER MRC (ARZF)
ARYGDINLET TYPE
THE TYPE OF INLET INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(ARYGDAE)
| Table 1 |
| Reply Code (AH98) | Reply |
| AE | OPEN |
| AB | SLEEVE |
IF STYLE/REPLY CODE(s) BJ WERE ENTERED FOR MRC ARZG, YOU MUST ANSWER MRC (SHPE and ARZH)
IF STYLE/REPLY CODE(s) BK WERE ENTERED FOR MRC ARZG, YOU MUST ANSWER MRC (ARZP and ADHZ and ARZR) or (ARZP and ARZQ and ARZR)
IF STYLE/REPLY CODE(s) BG WERE ENTERED FOR MRC ARZG, YOU MUST ANSWER MRC (ARZS and ARZT and AAJF and APJC)
ARZGDOUTLET TYPE
THE TYPE OF OUTLET INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(ARZGDBK)
| Table 1 |
| Reply Code (AB76) | Reply |
| BJ | FLANGED |
| BK | SLEEVE |
| BG | THREADED |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC ARZW, YOU MUST ANSWER MRC (ASAA and ADQB) or (ASAB and ADQB)
ARZWDREMOTE LOCATION INLET ADAPTER
AN INDICATION AS TO WHETHER OT NOT AN INLET ADAPTER FOR REMOTE LOCATION IS INCLUDED.
Enter the applicable reply code from the table below
(ARZWDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AHZVDSUBMERSIBILITY
AN INDICATION OF WHETHER OR NOT AN ITEM IS CAPABLE OF OPERATION WHILE SUBMERGED.
Enter the applicable reply code from the table below
(AHZVDAB)
| Table 1 |
| Reply Code (AG86) | Reply |
| AC | NONSUBMERSIBLE |
| AB | SUBMERSIBLE |
ARYC*DAIR CLEANER TYPE
AN INDICATION OF THE TYPE OF AIR CLEANER USED WITH THE ITEM.
Enter the applicable reply code from the table below
(ARYCDAB)
| Table 1 |
| Reply Code (AL65) | Reply |
| AB | PERMANENT |
| AC | THROW-AWAY |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAA2.0*;ABKVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAA2.0*;ABGLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC ARYD, YOU MUST ANSWER MRC (NMBR)
ARYD*DELEMENT REPLACEABILITY
AN INDICATION OF WHETHER OR NOT THE ELEMENT IS REPLACEABLE.
Enter the applicable reply code from the table below
(ARYDDC)
| Table 1 |
| Reply Code (AG84) | Reply |
| C | NONREPLACEABLE |
| B | REPLACEABLE |
NMBR*AQUANTITY
A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.
Enter the numeric reply with a minimum of one digit.
(NMBRA10*)
ARYH*GSLEEVE LOCATION
THE LOCATION OF THE SLEEVE.
Enter clear text.
(ARYHGCLEARTEXT)
ARYT*ASLEEVE CONNECTION QUANTITY
THE NUMBER OF SLEEVE CONNECTION(S)FURNISHED WITH THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ARYTA10*)
AMCA*JSLEEVE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLEEVE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMCAJAB2.0*;AMCAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARYW*JSLEEVE OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,WITH TERMINATED POINTS ON THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARYWJAA2.0*;ARYWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARYX*JSLEEVE INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARYXJAB2.0*;ARYXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARYY*DSLEEVE FLANGE SHAPE
THE PHYSICAL CONFIGURATION OF THE SLEEVE FLANGE.
Enter the applicable reply code from the table below
(ARYYDBM)
| Table 1 |
| Reply Code (AD07) | Reply |
| BM | OBLONG |
| BT | OVAL |
| RD | ROUND |
| SQ | SQUARE |
ARYZ*JSLEEVE FLANGE MOUNTING PROVISION AND QUANTITY
INDICATES THE TYPE AND NUMBER OF SLEEVE FLANGE MOUNTING PROVISION(S) PROVIDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ARYZJGY2*)
| Table 1 |
| Reply Code (AB89) | Reply |
| GY | HOLES |
| GG | STUDS |
ARZA*JSLEEVE FLANGE MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE FLANGE MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARZAJAC2.0*;ARZAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARZB*ASLEEVE FLANGE MOUNTING PROVISION THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE SLEEVE FLANGE MOUNTING PROVISION.
Enter the alpha-numeric reply with a minimum of one character.
(ARZBAL5)
ARZC*DSLEEVE FLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A SLEEVE FLANGE MOUNTING PROVISION.
Enter the applicable reply code from the table below
(ARZCDNP)
| Table 1 |
| Reply Code (AH06) | Reply |
| NP | NPT |
| NC | UNC |
| NF | UNF |
ARZD*DSLEEVE FLANGE MOUNTING PROVISION THREAD DIRECTION
THE DIRECTION OF THE SLEEVE FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ARZDDL)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ARZE*GSLEEVE FLANGE MOUNTING PROVISION SPACING
A MEASUREMENT OF THE SPACING OF THE SLEEVE FLANGE MOUNTING PROVISION.
Enter clear text.
(ARZEGCLEARTEXT)
ARZF*DELEMENT TYPE
THE TYPE OF ELEMENT(S) USED WITH THE ITEM.
Enter the applicable reply code from the table below
(ARZFDAD)
| Table 1 |
| Reply Code (AL67) | Reply |
| AB | FREE FLOW |
| AC | HOODED |
| AD | LOUVERED |
| AE | PERFORATED |
| AF | RECESSED HORN |
| AG | SCREEN |
SHPE*DSHAPE
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(SHPEDAXP)
| Table 1 |
| Reply Code (AD07) | Reply |
| Z | ANY ACCEPTABLE |
| BMF | FLAT STEPPED |
| AJG | IRREGULAR |
| BM | OBLONG |
| ALC | OVAL |
| BT | OVAL |
| ANC | RECTANGLE |
| AND | RECTANGULAR |
| RT | RECTANGULAR |
| RD | ROUND |
| SQ | SQUARE |
| AXP | TRIANGULAR |
| TR | TRIANGULAR |
ARZH*JFLANGE MOUNTING PROVISION AND QUANTITY
THE TYPE AND NUMBER OF FLANGE MOUNTING PROVISIONS INCLUDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ARZHJGY2*)
| Table 1 |
| Reply Code (AB89) | Reply |
| GY | HOLES |
| GG | STUDS |
ARZJ*JFLANGE BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARZJJAB2.0*;ARZJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARZK*AFLANGE MOUNTING PROVISION THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE FLANGE MOUNTING PROVISION.
Enter the alpha-numeric reply with a minimum of one character.
(ARZKAE1)
ARZL*DFLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A FLANGE MOUNTING PROVISION.
Enter the applicable reply code from the table below
(ARZLDBY)
| Table 1 |
| Reply Code (AH06) | Reply |
| BX | NC |
| BY | NF |
| NP | NPT |
| NC | UNC |
| NF | UNF |
ARZM*DFLANGE MOUNTING PROVISION THREAD DIRECTION
THE DIRECTION OF THE FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ARZMDL)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ARZN*GFLANGE MOUNTING PROVISION SPACING
A MEASUREMENT OF THE SPACING OF THE FLANGE MOUNTING PROVISION.
Enter clear text.
(ARZNGCLEARTEXT)
ARZP*DOUTLET SLEEVE TYPE
THE TYPE OF OUTLET SLEEVE USED ON THE ITEM.
Enter the applicable reply code from the table below
(ARZPDAC)
| Table 1 |
| Reply Code (AH46) | Reply |
| AC | INTERNAL |
| AD | PROTRUDING |
ADHZ*JMOUNTING OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADHZJAA2.0*;ADHZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARZQ*JMOUNTING INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARZQJAB2.0*;ARZQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARZR*DINTEGRAL CLAMP
AN INDICATION AS TO WHETHER OR NOT AN INTEGRAL CLAMP IS INCLUDED.
Enter the applicable reply code from the table below
(ARZRDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ARZS*AMOUNTING PROVISION THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE MOUNTING PROVISION.
Enter the alpha-numeric reply with a minimum of one character.
(ARZSAP3)
ARZT*DMOUNTING PROVISION THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A MOUNTING PROVISION.
Enter the applicable reply code from the table below
(ARZTDAQ)
| Table 1 |
| Reply Code (AH06) | Reply |
| BY | NF |
| SF | NPSF |
| NP | NPT |
| NT | NPTF |
| AQ | NS |
| UN | UN |
| NC | UNC |
| NF | UNF |
| NS | UNS |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDL)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
APJC*DTHREAD LOCATION
INDICATES THE LOCATION OF THE THREAD ON THE ITEM.
Enter the applicable reply code from the table below
(APJCDABX)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
ASAA*JADAPTER OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ADAPTER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASAAJAA2.0*;ASAAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASAB*JADAPTER INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ADAPTER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASABJAA2.0*;ASABJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) CK WERE ENTERED FOR MRC ADQB, YOU MUST ANSWER MRC (ASAC and ASAD and ASAE)
ADQB*DSECURING DEVICE TYPE
INDICATES THE TYPE OF DEVICE USED TO FASTEN THE ITEM.
Enter the applicable reply code from the table below
(ADQBDCK)
| Table 1 |
| Reply Code (AC52) | Reply |
| CJ | INTEGRAL CLAMP |
| CK | THREAD CONNECTION |
ASAC*AINLET ADAPTER THREAD SIZE
DESIGNATES THE INLET ADAPTER THREAD DIAMETER AND NUMBER OF THREADS PER INCH.
Enter the alpha-numeric reply with a minimum of one character.
(ASACAN1)
ASAD*DINLET ADAPTER THREAD SERIES DESIGNATOR
A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF AN INLET ADAPTER.
Enter the applicable reply code from the table below
(ASADDNP)
| Table 1 |
| Reply Code (AH06) | Reply |
| NP | NPT |
| NC | UNC |
| NF | UNF |
ASAE*DINLET ADAPTER THREAD DIRECTION
THE DIRECTION OF THE INLET ADAPTER THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ASAEDR)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
IF YOU ANSWER MRC ASAF, YOU MUST ANSWER MRC (ASAG and ASAH)
ASAF*APRECLEANER QUANTITY
THE NUMBER OF PRECLEANERS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ASAFA10*)
ASAG*GPRECLEANER LOCATION
INDICATES THE LOCATION OF THE PRECLEANER/S/ ON THE ITEM.
Enter clear text.
(ASAGGCLEARTEXT)
ASAH*DEXTENDED TUBE
AN INDICATION OF WHETHER OR NOT AN EXTENDED TUBE(S) IS INCLUDED.
Enter the applicable reply code from the table below
(ASAHDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ANTN*GSPECIFIC USE
THE REQUIRED PURPOSE OR APPLICATION FOR WHICH THE ITEM IS DESIGNED.
Enter clear text.
(ANTNGCLEARTEXT)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
KZTS*DCOGNIZANT SERVICE
THE MILITARY SERVICE THAT INITIALLY PROCURED THE ITEM FROM THE CONTRACTOR.
Enter the applicable reply code from the table below
(KZTSDN)
| Table 1 |
| Reply Code (AP57) | Reply |
| F | UNITED STATES AIR FORCE |
| M | UNITED STATES MARINE CORPS |
| N | UNITED STATES NAVY |
| A | USA |
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAO2)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAD0)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ277*;HZRDDHAZ092$$DHAZ285*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ012 | COPPER |
| HAZ092 | MAGNESIUM |
| HAZ277 | PHENOL |
| HAZ285 | PLASTIC |
| HAZ052 | ZINC |
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
AJJW*ACOMPONENT QUANTITY
THE NUMBER OF COMPONENTS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJJWA10*)
AJJX*DCOMPONENT DOCUMENT ORIGIN
THE ORIGINATOR /GOVERNMENTAL,INDUSTRIAL,OR OTHERWISE/ OF THE AVAILABLE DOCUMENT WHICH LISTS THE COMPONENT/S/ OF THE ITEM.
Enter the applicable reply code from the table below
(AJJXDAD*;AJJXDAF$DAD*;AJJXDAF$$DAD*)
| Table 1 |
| Reply Code (AF59) | Reply |
| AF | GOVERNMENT |
| AD | INDUSTRIAL |
AJJY*ADOCUMENT SOURCE
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER SOURCE,WHICH CONTROLS THE DOCUMENT.
Enter the alpha-numeric reply with five character(s) exactly.
(AJJYAF4T0S)
AJKC*GSUPPLY ITEMS AND QUANTITIES
A LISTING OF THOSE MAJOR COMPONENTS WHICH ARE COMPRISED OF A NATIONAL STOCK NUMBER,AN ITEM NAME,STANDARDIZED NAME,OR PART NAME,AND THE NUMBER OF EACH.
Enter clear text.
(AJKCGCLEARTEXT)
AYDS*GEND ITEM NAME
THE APPROVED ITEM NAME OR PART NAME OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter clear text.
(AYDSGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information