An instrument used for checking thermocouples and pyrometers. It is designed with a compensator which can be adjusted so that the measured electromotive force, corrected to a standard reference temperature, can be read directly from a scale. It can be used as a pH meter. Excludes:RESISTOR, VARIABLE, WIRE WOUND; RESISTOR, VARIABLE, NONWIRE WOUND; METER, HYDROGEN ION TEST; and PYROMETER (as modified).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED07344*)
BFHZDMEASUREMENT TYPE
INDICATES THE TYPE OF MEASUREMENT PROVIDED.
Enter the applicable reply code from the table below
(BFHZDCB*;BFHZDCE$$DCD*)
| Table 1 |
| Reply Code (AJ52) | Reply |
| A | ANY ACCEPTABLE |
| CA | BRIDGE CIRCUIT |
| CB | ELECTRONIC CIRCUIT |
| CD | MILLIVOLT CIRCUIT |
| CC | MOVING COIL RATIOMETER |
| CE | POTENTIOMETER CIRCUIT |
| CF | THERMOELECTRICAL CIRCUIT |
| CG | WHEATSTONE BRIDGE CIRCUIT |
ATEQDSCALE TYPE
INDICATES THE TYPE OF SCALE.
Enter the applicable reply code from the table below
(ATEQDAS*;ATEQDBW$$DCD*)
| Table 1 |
| Reply Code (AM12) | Reply |
| A | ANY ACCEPTABLE |
| AW | ARC |
| AX | BLACK INK FUSED IN YELLOW GLASS TUBE |
| AY | BRIDGE |
| AZ | BROAD ARC DIAL |
| BA | CALIBRATED BRASS |
| AP | CIRCULAR |
| BB | CONCAVE HORIZONTAL |
| BC | CONCENTRIC |
| BD | CONCENTRIC ARC DIAL |
| BE | CONCENTRIC DIAL |
| BF | CONCENTRIC ROTATING DIAL |
| BG | DIAL |
| EC | DIGITAL |
| BH | DISK |
| BJ | DRUM |
| BK | ECCENTRIC |
| BL | ENCLOSED GLASS |
| BM | ENGRAVED BRASS |
| BN | ENGRAVED STEM |
| BP | ENGRAVED TUBE |
| BQ | ETCHED FLAT GLASS |
| BR | ETCHED STEM |
| BS | ETCHED TUBE |
| BT | FUSED STEM |
| AS | HORIZONTAL |
| BW | INCLOSED METAL |
| BX | INCLOSED PAPER |
| BY | METAL BACK |
| BZ | METAL NONMAGNETIC |
| CA | METER DIAL |
| CB | MULTIPLE |
| CC | PAPER |
| CD | PLASTIC |
| CE | SINGLE |
| CF | STEM |
| AT | VERTICAL |
APSKJSCALE RANGE
AN INDICATION OF THE SCALE RANGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(APSKJBDM32.0/P50.0*;APSKJBDM32.0/P50.0$$JBD*;APSKJBDM32.0/P50.0$JBDM32.0/P50.0*)
| Table 1 |
| Reply Code (AJ20) | Reply |
| BA | ATMOSPHERE |
| KC | BAR |
| BB | BRAKE MEAN EFFECTIVE PRESSURE |
| BC | BRAKE MEAN EFFECTIVE PRESSURE TORQUE PRESSURE |
| BD | CAPACITY |
| BE | CENTIMETERS |
| BF | CENTIMETERS OF WATER |
| BG | CONTENTS |
| BH | CUBIC CENTIMETERS |
| BJ | CUBIC FEET |
| BK | CUBIC FEET AT 70 DEG F |
| BL | CUBIC FEET OF GAS |
| BM | DEG CELSIUS |
| BN | DEG FAHRENHEIT |
| AS | DEGREES |
| BP | FEET |
| BQ | FEET OF ALTITUDE |
| BR | FEET OF DEPTH |
| BS | FEET OF SALT WATER |
| BT | FEET OF SEA WATER |
| BW | FEET OF WATER |
| BX | FEET PER HOUR |
| HT | FEET PER MINUTE |
| HX | FEET PER SECOND |
| BY | FOOT POUNDS |
| BZ | GALLONS |
| CA | GALLONS OF LIQUID NITROGEN |
| CB | GALLONS OF LIQUID OXYGEN |
| CC | GALLONS OF OIL |
| CD | GALLONS OF WATER |
| LS | HECTOPASCAL |
| AW | INCHES |
| CE | INCHES ABSOLUTE PRESSURE BELOW BAROMETER |
| CF | INCHES HG |
| CG | INCHES OF KEROSENE |
| CH | INCHES OF MERCURY |
| CJ | INCHES OF MERCURY ABSOLUTE PRESSURE |
| CK | INCHES OF PRESSURE |
| CL | INCHES OF VACUUM |
| CM | INCHES OF WATER |
| CN | INCHES OF WATER PRESSURE |
| CP | KILOGRAMS |
| CQ | KILOGRAMS PER CENTIMETER |
| CR | KILOGRAMS PER SQUARE CENTIMETER |
| CS | KNOTS |
| CT | KNOTS AIR SPEED |
| CW | KNOTS PER HOUR |
| CX | LITERS |
| CY | LITERS OF LIQUID AIR |
| CZ | LITERS PER MINUTE |
| DA | METERS |
| DB | MICRONS |
| JA | MICRONS OF MERCURY |
| DC | MILES |
| DD | MILES PER HOUR |
| DE | MILES PER HOUR AIR SPEED |
| DF | MILLIBARS |
| DG | MILLIMETERS |
| DH | MILLIMETERS OF MERCURY |
| JF | MILLIVOLTS |
| AG | MINUTE |
| DJ | OUNCES |
| DK | OUNCES PER SQUARE INCH |
| AX | PERCENT |
| AY | POUNDS |
| DL | POUNDS LOAD |
| DM | POUNDS OF AIR PER MINUTE |
| DN | POUNDS OF NITROGEN |
| DP | POUNDS OF VACUUM PER SQUARE INCH |
| DQ | POUNDS PER SQUARE INCH |
| HP | POUNDS PER SQUARE INCH ABSOLUTE |
| DR | POUNDS PRESSURE |
| DS | POUNDS PRESSURE PER SQUARE INCH |
| DT | POUNDS PRESSURE PER SQUARE ROOT INCH |
| DW | PRESSURE |
| DX | PRESSURE RATIO |
| DY | STANDARD CUBIC CENTIMETER |
| DZ | TANK |
| EA | TONS |
| EB | TONS PRESSURE |
| EC | UNITS |
| AP | VOLTS |
AWAGJSCALE SMALLEST INCREMENT
THE SMALLEST VALUE BETWEEN THE MARKINGS ON A SCALE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWAGJAN2.0*;AWAGJAN2.0$$JAN2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LM | BAR |
| MP | CENTIMETER |
| AC | CUBIC CENTIMETERS |
| CY | CUBIC FEET |
| CP | CUBIC INCHES |
| GT | DEG CELSIUS |
| GW | DEG FAHRENHEIT |
| CE | DEGREES |
| GG | FOOT |
| AF | GALLONS |
| LW | HECTOPASCAL |
| BC | INCHES |
| FR | INCHES OF MERCURY |
| AJ | KILOGRAMS |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| CC | LITERS |
| CK | METERS |
| GD | MICRONS |
| KN | MILLIBARS |
| HC | MILLIMETERS |
| KZ | MILLIMETERS OF MERCURY |
| KX | MILLIVOLTS |
| AN | OUNCES |
| KY | OUNCES PER SQUARE INCH |
| AS | POUNDS |
| FB | POUNDS PER SQUARE INCH |
| BY | TONS |
| NA | VOLT |
| MZ | VOLTAGE DIRECT CURRENT |
AMQYDINSTALLATION DESIGN
THE INSTALLATION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AMQYDAF)
| Table 1 |
| Reply Code (AJ17) | Reply |
| CA | MOUNTED |
| AF | PORTABLE |
IF STYLE/REPLY CODE(s) AAW WERE ENTERED FOR MRC BHLW, YOU MUST ANSWER MRC (BHLZ and AKRG and BHMB)
BHLWDINDICATING POINT TYPE
INDICATES THE TYPE OF INDICATING POINT PROVIDED.
Enter the applicable reply code from the table below
(BHLWDAAW)
| Table 1 |
| Reply Code (AJ44) | Reply |
| AAW | MULTIPLE |
| AAT | SINGLE |
BHLZ*GCONTROL SWITCH TYPE
INDICATES THE TYPE OF CONTROL SWITCH.
Enter clear text.
(BHLZGCLEARTEXT)
AKRG*APOINT QUANTITY
THE NUMBER OF POINTS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AKRGA10*)
BHMB*AOFF POSITION QUANTITY
THE NUMBER OF OFF POSITION(S) PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BHMBA10*)
BHMC*DCASE TYPE
INDICATES THE TYPE OF CASE PROVIDED.
Enter the applicable reply code from the table below
(BHMCDAES*;BHMCDABG$$DACG*)
| Table 1 |
| Reply Code (AJ95) | Reply |
| A | ANY ACCEPTABLE |
| AEN | BOX W/HANDLE |
| AFD | CARRYING CASE W/HANDLE |
| ABG | CORROSION RESISTANT |
| AAD | DRIPPROOF |
| ABJ | DUST TIGHT |
| AAE | DUSTPROOF |
| AEP | DUSTPROOF W/LEATHER CARRYING STRAP |
| AAH | EXPLOSION PROOF |
| AFE | EXPLOSION PROOF W/CARRYING CASE |
| AER | FUMEPROOF |
| AES | FUMEPROOF W/HINGED DOOR |
| AET | FUNGUSPROOF W/HINGED LID |
| AAK | HERMETICALLY SEALED |
| AEW | HINGED LID CARRYING CASE W/HANDLE |
| ABT | MOISTURE PROOF |
| AEX | MOISTURE PROOF W/HINGED DOOR |
| ACH | SHOCK PROOF |
| ACG | SHOCK RESISTANT |
| AEY | SHOCKPROOF CASE W/HANDLE |
| AEZ | SPARKPROOF |
| AFA | SPARKPROOF W/TELESCOPE HOLDER |
| ACJ | SPLASH PROOF |
| AFB | SPLASH PROOF W/HANDLE |
| AFC | VAPORPROOF |
| ACR | VIBRATION PROOF |
| AAY | WATERPROOF |
AWZJ*DPOWER SOURCE
THE SOURCE OF POWER WHICH PROVIDES THE ENERGY REQUIRED FOR THE OPERATION OF THE ITEM.
Enter the applicable reply code from the table below
(AWZJDCF*;AWZJDBJ$DCF*;AWZJDBJ$$DCF*)
| Table 1 |
| Reply Code (AG27) | Reply |
| BJ | EXTERNAL |
| CF | INTERNAL |
BGKS*GSCALE ACCURACY
THE DEGREE OF CONFORMITY OF A SCALE MEASUREMENT TO A STANDARD OR A TRUE VALUE.
Enter clear text.
(BGKSGCLEARTEXT)
AMNK*GSCALE CALIBRATION
AN INDICATION OF THE MANNER IN WHICH THE SCALE IS CALIBRATED.
Enter clear text.
(AMNKGCLEARTEXT)
BGLB*JSCALE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A SCALE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGLBJAB2.0*;BGLBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDWDC000*;MATT3AEEDWDC000$DALA000*;MATT3AEEDWDC000$$DALA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CEP | CASE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| WDC000 | WOOD |
| WDR000 | WOOD OAK |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAB2.0*;ABFYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDARN*;AXGYDARS$DAQP*;AXGYDARS$$DAQP*)
| Table 1 |
| Reply Code (AM39) | Reply |
| A | ANY ACCEPTABLE |
| AQP | BACKPLATE |
| ABB | BASE |
| ADG | BAYONET |
| AAC | BOLT |
| ABC | BRACKET |
| ABD | BUSHING |
| ARK | CARRYING CASE |
| ABF | CASE |
| ARL | CENTER BACK 1/4 NPT FIXED CONNECTION |
| ABH | CLAMP |
| AFL | CLIP |
| ARN | CONNECTION |
| ARP | EXTERNAL NPTF CONNECTION |
| ARQ | EXTERNAL PIPE CONNECTION |
| ARR | EXTERNAL PIPE THREAD 1/8 NPT |
| ARS | EXTERNAL STRAIGHT THREAD CONNECTION |
| AFT | EXTERNAL THREAD |
| ACR | FLANGE |
| ARW | FLANGE BASE |
| ART | FLARED TUBE CONNECTION |
| AGQ | FLUSH |
| ARX | FLUSH FLANGE |
| ARY | FLUSH PANEL |
| ACP | HOLE |
| ARZ | INLET CONNECTION |
| ASA | INLET PIPE CONNECTION |
| ASB | INSERT TYPE STOP NUTS |
| ASC | INSERTED NUTS |
| AGH | INTERNAL THREAD |
| ASD | LOCKNUT |
| ABN | LUG |
| ASE | METAL CASE FIXED |
| ASF | METAL CASE FLANGE |
| ASG | METAL CASE RUBBER WASHER |
| ASH | METAL CASE SEPARABLE SOCKET |
| ASJ | NPTF FITTING |
| AED | PANEL |
| ASK | PANEL FLANGE |
| ASM | PANEL W/SCREWS |
| ASL | PEDESTAL |
| ASN | PIN CLIP |
| ASP | PIPE FITTING |
| ASQ | PLASTIC CASE FIXED |
| AEE | PLATE |
| APF | PLUG |
| AST | PORTABLE METAL CASE |
| ASW | PORTABLE METAL CUP CASE |
| ASX | PORTABLE WOOD BACK |
| ASR | PORTABLE WOOD BACK CUP CASE |
| ASY | PRESSURE BOSS AND 10050-12 |
| ASZ | RIGID STEM |
| ATA | RUBBER BUSHING |
| ATB | RUBBER GROMMET |
| ABW | SCREW |
| AQY | SEMIFLUSH |
| ATC | SEMIFLUSH PANEL |
| ARM | SHOCKPROOF CASE |
| BPZ | SOCKET STEM |
| AJM | STAND |
| ATD | STOP NUTS |
| ATE | STRAIGHT PIPE THREAD |
| AAE | STUD |
| AEG | SURFACE |
| ATF | SURFACE WALL |
| ARD | TABLE |
| ACS | THREAD |
| ATG | THREADED BOSS |
| AFA | THREADED BUSHING |
| AHF | THREADED HOLE |
| ATH | THREADED INLET CONNECTION |
| ATJ | THREADED MALE CONNECTION |
| ATK | THREADED NECK |
| ATL | THREADED PIPE CONNECTION |
| ATM | THREADED SOCKET |
| ATN | THREADED STEM |
| AET | THREADED STUD |
| ATP | TOP HOOK |
| ATQ | UNION CONNECTION |
| ARE | UNIVERSAL |
| ATR | VENT HOLE PLUG |
| ATS | WALL |
| AEJ | WALL BRACKET |
| ATT | WALL FLANGE |
| AKK | WELDED |
| ATW | WOOD CASE PORTABLE |
BHMH*DMOUNTING CONNECTION LOCATION
INDICATES THE MOUNTING CONNECTION LOCATION.
Enter the applicable reply code from the table below
(BHMHDBHM*;BHMHDDTP$DBJC*;BHMHDDTP$$DBJC*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| A | ANY ACCEPTABLE |
| AAZ | BACK |
| BHJ | BACK, CENTER |
| BHK | BACK, LOWER |
| BHL | BACK, RIGHT |
| ADC | BOTH SIDES |
| ABA | BOTTOM |
| BHM | BOTTOM REAR |
| AHP | CENTER |
| ABB | END |
| BHN | LEFT REAR BOTTOM |
| ACF | LEFT SIDE |
| BHP | LEFT SIDE TOP |
| BHQ | LOWER |
| BHS | LOWER FRONT |
| AEN | LOWER LEFT HAND SIDE |
| BHT | LOWER REAR LEFT SIDE |
| DTM | LOWER REAR RIGHT SIDE |
| AEP | LOWER RIGHT HAND SIDE |
| CLD | LOWER SIDE |
| BHW | ON 4 CORNERS |
| ACR | RIGHT SIDE |
| ACZ | SIDE |
| ABD | TOP |
| BHY | TOP BACK |
| AQK | TOP CENTER |
| DTN | TOP CENTER REAR |
| DTP | TOP LEFT REAR |
| BHZ | TOP LEFT SIDE |
| DTQ | TOP RIGHT REAR |
| AER | TOP RIGHT SIDE |
| BEK | TOP SIDE |
| AYM | UPPER |
| BJA | UPPER BACK |
| BJB | UPPER FRONT |
| BJC | UPPER LEFT RIGHT SIDE |
| BJD | UPPER LEFT SIDE |
| BJE | UPPER REAR RIGHT SIDE |
| AET | UPPER RIGHT HAND SIDE |
| BJF | UPPER SIDE |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAA2.0*;ABKGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJLA2.0*;ABTBJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BCCL*ASTUD QUANTITY
THE NUMBER OF STUD(S) PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BCCLA10*)
BHMJ*DSTUD LOCATION
INDICATES THAT PORTION OF AN ITEM ON WHICH THE STUD IS LOCATED.
Enter the applicable reply code from the table below
(BHMJDBJF*;BHMJDACR$$DACZ*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| A | ANY ACCEPTABLE |
| AAZ | BACK |
| BHJ | BACK, CENTER |
| BHK | BACK, LOWER |
| BHL | BACK, RIGHT |
| ADC | BOTH SIDES |
| ABA | BOTTOM |
| BHM | BOTTOM REAR |
| AHP | CENTER |
| ABB | END |
| BHN | LEFT REAR BOTTOM |
| ACF | LEFT SIDE |
| BHP | LEFT SIDE TOP |
| BHQ | LOWER |
| BHS | LOWER FRONT |
| AEN | LOWER LEFT HAND SIDE |
| BHT | LOWER REAR LEFT SIDE |
| DTM | LOWER REAR RIGHT SIDE |
| AEP | LOWER RIGHT HAND SIDE |
| CLD | LOWER SIDE |
| BHW | ON 4 CORNERS |
| ACR | RIGHT SIDE |
| ACZ | SIDE |
| ABD | TOP |
| BHY | TOP BACK |
| AQK | TOP CENTER |
| DTN | TOP CENTER REAR |
| DTP | TOP LEFT REAR |
| BHZ | TOP LEFT SIDE |
| DTQ | TOP RIGHT REAR |
| AER | TOP RIGHT SIDE |
| BEK | TOP SIDE |
| AYM | UPPER |
| BJA | UPPER BACK |
| BJB | UPPER FRONT |
| BJC | UPPER LEFT RIGHT SIDE |
| BJD | UPPER LEFT SIDE |
| BJE | UPPER REAR RIGHT SIDE |
| AET | UPPER RIGHT HAND SIDE |
| BJF | UPPER SIDE |
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDAUA000$DPDA000*;PRMTDAUA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000F2.0*;PMWTJPDA000F2.0$$JPDA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA0002.0*;PMLCJPDA0002.0$JPDA0002.0*;PMLCJPDA0002.0$$JPDA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAF4)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAN5)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ277*;HZRDDHAZ252$$DHAZ008*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ027 | IRIDIUM |
| HAZ237 | MANGANESE |
| HAZ252 | NICKEL |
| HAZ277 | PHENOL |
| HAZ303 | SILVER |
| HAZ052 | ZINC |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information