A tachometer that consists of indicator(s), generating transmitter(s), and the necessary connections.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED07113*)
APQBDUNIT TYPE
INDICATES THE TYPE OF UNIT.
Enter the applicable reply code from the table below
(APQBDCMQ*;APQBDCMK$DCMR*)
| Table 1 |
| Reply Code (AK95) | Reply |
| A | ANY ACCEPTABLE |
| AMG | CENTRIFUGAL |
| AMH | CHRONOMETRIC |
| CFK | DIODE |
| ALS | ELECTRICALLY OPERATED |
| CMQ | FLASHTUBE |
| CHC | LAMP |
| ADA | MAGNETIC |
| AMJ | PHOTOELECTRIC CELL |
| CMR | SELF-GENERATING |
| CMK | TRANSDUCER |
BGNY*BTIME INTERVAL IN SECONDS
THE MEASUREMENT OF TIME BETWEEN EVENTS,EXPRESSED IN SECONDS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BGNYB2.0*;BGNYB2.0$$BM2.0*)
IF STYLE/REPLY CODE(s) CJ WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (AHGJ)
AAXXDMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDBM*;AAXXDA$DHX*)
| Table 1 |
| Reply Code (AA78) | Reply |
| A | ANY ACCEPTABLE |
| CJ | PANEL |
| BM | PEDESTAL |
| HX | RIGID STEM |
AHGJ*DMOUNTING FEATURE TYPE
INDICATES THE TYPE OF FEATURE USED TO MOUNT THE ITEM.
Enter the applicable reply code from the table below
(AHGJDC*;AHGJDB$DA*)
| Table 1 |
| Reply Code (AF30) | Reply |
| A | ANY ACCEPTABLE |
| B | FLUSH |
| C | SURFACE |
APSJASCALE QUANTITY
THE NUMBER OF SCALES ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(APSJA10*)
BGPQDSCALE MEASUREMENT UNIT
AN INDICATION OF THE UNIT OF MEASURE FOR WHICH THE SCALE IS DESIGNED.
Enter the applicable reply code from the table below
(BGPQDFC*;BGPQDA$$DFE*)
| Table 1 |
| Reply Code (AG67) | Reply |
| A | ANY ACCEPTABLE |
| FE | FEET PER MINUTE |
| CG | PERCENT |
| FC | REVOLUTIONS PER MINUTE |
| FD | REVOLUTIONS PER SECOND |
ANSZFSCALE MEASUREMENT RANGE
THE MINIMUM AND MAXIMUM NUMERIC VALUES REPRESENTING THE MEASUREMENT COVERAGE OF A SCALE.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(ANSZFM2.0/P4.7*)
AWAGJSCALE SMALLEST INCREMENT
THE SMALLEST VALUE BETWEEN THE MARKINGS ON A SCALE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWAGJFD2.0*;AWAGJFD2.0$$JFD2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| FE | FEET PER MINUTE |
| FH | METERS PER MINUTE |
| CG | PERCENT |
| FC | REVOLUTIONS PER MINUTE |
| FD | REVOLUTIONS PER SECOND |
AQPS*DMAJOR GRADUATION COLOR
THE HUE OR TINT OF THE MAJOR GRADUATION.
Enter the applicable reply code from the table below
(AQPSDYE0009*;AQPSDBL0036$DRE0000*;AQPSDBL0036$$DRE0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AL0000 | ALUMINUM |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| MS0073 | CHROME |
| CR0000 | CREAM |
| GR0000 | GREEN |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| SL0000 | SILVER |
| WH0000 | WHITE |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
AQPT*DMINOR GRADUATION COLOR
THE HUE OR TINT OF THE MINOR GRADUATION.
Enter the applicable reply code from the table below
(AQPTDCR0000*;AQPTDGR0000$DAL0000*;AQPTDGR0000$$DAL0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AL0000 | ALUMINUM |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| MS0073 | CHROME |
| CR0000 | CREAM |
| GR0000 | GREEN |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| SL0000 | SILVER |
| WH0000 | WHITE |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
BGPBDLUMINOUS SCALE
AN INDICATION OF WHETHER OR NOT A LUMINOUS SCALE IS PROVIDED.
Enter the applicable reply code from the table below
(BGPBDC*;BGPBDB$DB*;BGPBDB$$DB*)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
ASPC*APOINTER QUANTITY
THE NUMBER OF POINTERS INCLUDED.
Enter the numeric reply with a minimum of one digit.
(ASPCA10*)
ASPE*GPOINTER MARKING
AN INDICATION OF THE MARKING/S/ ON THE POINTER.
Enter clear text.
(ASPEGCLEARTEXT)
ASSS*DPOINTER COLOR
THE HUE OR TINT OF THE POINTER.
Enter the applicable reply code from the table below
(ASSSDA*;ASSSDSL0000$$DCR0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AL0000 | ALUMINUM |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| MS0073 | CHROME |
| CR0000 | CREAM |
| GR0000 | GREEN |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| SL0000 | SILVER |
| WH0000 | WHITE |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
ASPD*DPOINTER FINISH
AN INDICATION OF THE FINISH ON THE POINTER.
Enter the applicable reply code from the table below
(ASPDDG*;ASPDDD$$DC*)
| Table 1 |
| Reply Code (AB54) | Reply |
| A | ANY ACCEPTABLE |
| F | FLUORESCENT |
| B | FLUORESCENT PAINT |
| G | PHOSPHORESCENT |
| C | PHOSPHORESCENT PAINT |
| R | RADIOACTIVE |
| D | RADIUM |
BGPC*DPOINTER MOVEMENT DIRECTION
AN INDICATION OF THE DIRECTION IN WHICH THE POINTER MOVES.
Enter the applicable reply code from the table below
(BGPCDAAB*;BGPCDAAE$$DAAD*)
| Table 1 |
| Reply Code (AN16) | Reply |
| A | ANY ACCEPTABLE |
| AAB | CLOCKWISE |
| AAC | COUNTERCLOCKWISE |
| AAD | LEFT TO RIGHT |
| AAE | RIGHT TO LEFT |
AQKC*ADIAL QUANTITY
THE NUMBER OF DIALS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AQKCA10*)
AQZB*DNUMERAL COLOR
THE HUE OR TINT OF THE NUMERAL.
Enter the applicable reply code from the table below
(AQZBDCR0000*;AQZBDA$$DSL0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AL0000 | ALUMINUM |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| MS0073 | CHROME |
| CR0000 | CREAM |
| GR0000 | GREEN |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| SL0000 | SILVER |
| WH0000 | WHITE |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
ARCG*DDIAL BACKGROUND COLOR
THE HUE OR TINT OF THE DIAL BACKGROUND.
Enter the applicable reply code from the table below
(ARCGDBL0000*;ARCGDSL0000$$DYE0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AL0000 | ALUMINUM |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| MS0073 | CHROME |
| CR0000 | CREAM |
| GR0000 | GREEN |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| SL0000 | SILVER |
| WH0000 | WHITE |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
ASTKDDIAL ILLUMINATION
AN INDICATION OF WHETHER OR NOT DIAL ILLUMINATION
Enter the applicable reply code from the table below
(ASTKDC)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
AEWY*DLAMP TYPE
INDICATES THE FORM,CONSTRUCTION,OR TYPE OF LAMP WHICH DISTINGUISHES IT FROM OTHER LIKE ITEMS.
Enter the applicable reply code from the table below
(AEWYDAD)
| Table 1 |
| Reply Code (AD48) | Reply |
| A | ANY ACCEPTABLE |
| AD | FLUORESCENT |
| AF | INCANDESCENT |
| AK | NEON |
AEWX*BLAMP VOLTAGE RATING IN VOLTS
THE VOLTAGE FOR WHICH THE LAMP IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEWXB2.0*;AEWXB2.0$$BM2.0*)
ANRXDCASE SHAPE
THE GENERAL OUTSIDE CONFIGURATION OF THE CASE.
Enter the applicable reply code from the table below
(ANRXDRD*;ANRXDRT$DLB*)
| Table 1 |
| Reply Code (AD07) | Reply |
| A | ANY ACCEPTABLE |
| LB | FAN |
| BC | IRREGULAR |
| DP | L |
| BT | OVAL |
| RT | RECTANGULAR |
| RD | ROUND |
| SQ | SQUARE |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAA2.0*;ADAVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAC2.0*;ABFYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAYX*DDRIVE CONNECTION TYPE
INDICATES THE TYPE OF CONNECTION BETWEEN THE PRIME MOVER AND THE SHAFT.
Enter the applicable reply code from the table below
(AAYXDBJ*;AAYXDBK$$DBM*)
| Table 1 |
| Reply Code (AA85) | Reply |
| A | ANY ACCEPTABLE |
| BJ | FLEXIBLE |
| BK | SLOTTED |
| BL | SQUARE |
| BM | THREADED |
AKCT*DSHAFT ROTATION DIRECTION
THE DIRECTION OF ROTATION OF A ROTATING SHAFT AS VIEWED FROM THE DRIVE END.
Enter the applicable reply code from the table below
(AKCTDB*;AKCTDE$$DC*)
| Table 1 |
| Reply Code (AC84) | Reply |
| B | CLOCKWISE |
| E | CLOCKWISE/COUNTERCLOCKWISE |
| C | COUNTERCLOCKWISE |
BGPLDMANUAL RESET
AN INDICATION OF WHETHER OR NOT A MANUAL RESET IS PROVIDED.
Enter the applicable reply code from the table below
(BGPLDC)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
AMQYDINSTALLATION DESIGN
THE INSTALLATION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AMQYDAJ*;AMQYDAF$DAF*)
| Table 1 |
| Reply Code (AJ17) | Reply |
| AJ | FIXED |
| AF | PORTABLE |
ACDCDCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDC*;ACDCDB$DD*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| D | AC/DC |
| C | DC |
ELECBVOLTAGE IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ELECB2.0*;ELECB2.0$$BM2.0*)
AJSS*JFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJSSJB2.0*;AJSSJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDB$DC*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| E | SINGLE/THREE |
| C | THREE |
| B | TWO |
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRTA000*;PRMTDAGA000$DIRA000*;PRMTDAGA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000R2.0*;PMWTJPDA000R2.0$JPDA000R2.0*;PMWTJPDA000R2.0$$JPDA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3CEPDALB000*;MATT3CEPDALB000$DALA000*;MATT3CEPDALB000$$DALA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CEP | CASE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| PCA000 | PLASTIC |
| STA000 | STEEL |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information