A tool with a striking face on one or both ends of a metallic weighted head fixed crosswise to a handle. It is used to strike and/or drive objects, or beat malleable materials. For items stocked without FACE, HAMMER, INSERTED, see HOLDER, INSERTED HAMMER FACE. Excludes:DRIVER, COOPER'S and mechanical hammers. See also MALLET (as modified).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED05970*)
CYNEDHEAD MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE HEAD IS FABRICATED.
Enter the applicable reply code from the table below
(CYNEDCUA000*;CYNEDPBA000$DPCAP00*;CYNEDPBA000$$DPCAP00*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| FEC000 | IRON MALLEABLE |
| PBA000 | LEAD |
| LRA000 | LEATHER |
| PCA000 | PLASTIC |
| PCN000 | PLASTIC PHENOLIC |
| PCAR00 | PLASTIC POLYTRIFLUOROETHYLENE |
| PCAP00 | PLASTIC VINYL |
| RCE000 | RUBBER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| SNB000 | TIN |
| WDC000 | WOOD |
CYASDHANDLE MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE HANDLE IS FABRICATED.
Enter the applicable reply code from the table below
(CYASDSTB000*;CYASDRCE000$DGSB000*;CYASDRCE000$$DGSB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| FEC000 | IRON MALLEABLE |
| PBA000 | LEAD |
| LRA000 | LEATHER |
| PCA000 | PLASTIC |
| PCN000 | PLASTIC PHENOLIC |
| PCAR00 | PLASTIC POLYTRIFLUOROETHYLENE |
| PCAP00 | PLASTIC VINYL |
| RCE000 | RUBBER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| SNB000 | TIN |
| WDC000 | WOOD |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASNJHANDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASNJAC2.0*;AASNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 36, 37, 43, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 61, 63, 64, 73, 75, 76, 77, 78, 79, 81, 8A, 14A, 21A, 22A, 22B, 32A, 55A, 56A, 80, 80A, 70, 71, 72 OR 74 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHRU)
IF STYLE/REPLY CODE(s) 33, 38, 39, 40, 41, 42, 44, 45, 57, 58, 59, 60, 38A, 38B, 39A, 39B, 40A, 40B OR 59A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHRU and AASV)
IF STYLE/REPLY CODE(s) 34 OR 35 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASHR)
IF STYLE/REPLY CODE(s) 62 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ARGG)
IF STYLE/REPLY CODE(s) 65, 66, 67 OR 68 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASHR and ARGG)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL11)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AH10689 | 1 | BLACKSMITH'S CROSS-PEEN |
| AH10698 | 10 | SHIPFITTERS |
| AH10699 | 11 | BOILERMAKER'S, DOUBLE-FACE |
| AH10700 | 12 | MACHINIST'S RIVETING |
| AH10701 | 13 | TINNER'S RAISING |
| DR03053 | 14 | UPHOLSTERER'S |
| DR03054 | 14A | UPHOLSTERER'S W/CLAW ON HANDLE |
| AH10703 | 15 | GEOLOGIST'S |
| AH10704 | 16 | MACHINIST'S BALL-PEEN |
| AH10705 | 17 | MACHINIST'S CROSS-PEEN |
| AH10706 | 18 | MACHINIST'S STRAIGHT-PEEN |
| AH10707 | 19 | COOPER'S |
| AH10690 | 2 | SCALING |
| AH10708 | 20 | SHOEMAKER'S |
| DR03055 | 21 | CARPENTER'S RIPPING, STRAIGHT-CLAW |
| DR03056 | 21A | CARPENTER'S RIPPING, STRAIGHT-CLAW W/PLAIN NECK |
| DR03057 | 22 | CARPENTER'S NAILING CURVED-CLAW |
| DR03058 | 22A | CARPENTER'S NAILING CURVED-CLAW W/PLAIN NECK |
| DR03059 | 22B | CARPENTER'S NAILING CURVED-CLAW SQUARE FACE |
| AH10711 | 23 | FARRIER'S, DRIVING |
| AH10712 | 24 | FARRIER'S SHARPENING |
| AH10713 | 25 | FARRIER'S FITTING |
| AH10714 | 26 | FARRIER'S, TURNING |
| AH10715 | 27 | MAUL, SHIP |
| AH10716 | 28 | MAUL, WOODCHOPPER'S |
| AH10717 | 29 | SLEDGE, STONE |
| AH10691 | 3 | TINNERS, SETTING |
| AH10718 | 30 | STRIKING |
| AH10719 | 31 | MAUL, RAILROAD TRACK, STANDARD |
| DR03060 | 32 | NAPPING |
| DR03061 | 32A | STUNNING |
| AH10721 | 33 | HAND-DRILLING |
| AH10722 | 34 | SOFT-HEAD |
| AH10723 | 35 | SOFT-FACE, REGULAR FACES |
| AH10724 | 36 | SPALLING, DOUBLE FACE |
| AH10725 | 37 | MASON'S SINGLE-FACE |
| DR03062 | 38 | BODYWORKER'S BUMPING |
| DR03063 | 38A | BODYWORKER'S BUMPING |
| DR03064 | 38B | BODYWORKER'S BUMPING |
| DR03065 | 39 | BODYWORKER'S DINGING |
| DR03066 | 39A | BODYWORKER'S DINGING |
| DR03067 | 39B | BODYWORKER'S DINGING |
| AH10692 | 4 | TACK |
| DR03068 | 40 | BODYWORKER'S OFFSET DINGING |
| DR03069 | 40A | BODYWORKER'S OFFSET DINGING |
| DR03070 | 40B | BODYWORKER'S OFFSET DINGING |
| AH10729 | 41 | BODYWORKER'S, POINT-DINGING |
| AH10730 | 42 | BODYWORKER'S, LONG-PICK, DINGING |
| AH10731 | 43 | BRICKLAYER'S |
| AH10732 | 44 | BODYWORKER'S ROUGHING OUT |
| AH10733 | 45 | BODYWORKER'S, FENDER-BUMPER |
| AH10734 | 46 | SAW SETTING AND SWAGING |
| AH10735 | 47 | SAW SETTING AND SWAGING |
| AH10736 | 48 | PITON, MOUNTAIN |
| AH10737 | 49 | TACK, CLAW HEAD |
| AH10693 | 5 | SLEDGE, BLACKSMITH'S, CROSS-PEEN |
| AH10738 | 50 | LINEMAN'S |
| AH10739 | 51 | SOFT-HEAD |
| AH10740 | 52 | HARD AND SOFT FACE |
| AH10741 | 53 | MAUL, RAILROAD TRACK, PITTSBURGH BELL |
| AH10742 | 54 | SAWMAKER'S CROSS-PEEN |
| DR03071 | 55 | TACK |
| DR03072 | 55A | TACK W/CLAW ON HANDLE |
| DR03956 | 56 | UPHOLSTERER'S, TRIMMING |
| DR03957 | 56A | UPHOLSTERER'S, TRIMMING W/CLAW ON HANDLE |
| AH10745 | 57 | BODYWORKER'S, ROUGHING-OUT |
| AH10746 | 58 | BODYWORKER'S, OFFSET BUMPING |
| DR03073 | 59 | BODYWORKER'S, PICK AND SURFACING |
| DR03074 | 59A | BODYWORKER'S, PICK AND SURFACING |
| AH10694 | 6 | TINNERS, RIVETING |
| AH10748 | 60 | BODYWORKER'S, FORMING |
| AH10749 | 61 | METALWORKER'S, PLANISHING |
| AH10750 | 62 | CHASING |
| AH10751 | 63 | JEWELER'S |
| AH10752 | 64 | WELDER'S |
| AH10753 | 65 | SPLIT HEAD, INSERTED FACE |
| AH10754 | 66 | PRESS-IN, INSERTED FACE |
| AH10755 | 67 | SCREW-IN, INSERTED FACE |
| AH10756 | 68 | PRESS-ON, INSERTED FACE |
| AH10695 | 7 | SLEDGE, BLACKSMITH'S STRAIGHT-PEEN |
| DQ01146 | 70 | TUBE SPLIT |
| DQ01147 | 71 | CARPENTER'S |
| DQ01148 | 72 | MASON'S |
| AH10757 | 73 | JOINER'S |
| DQ01149 | 74 | SQUARE SOFT-HEAD |
| AH10758 | 75 | BODYWORKER'S, GROOVING |
| AH10759 | 76 | BODYWORKER'S BUMPING |
| AH10760 | 77 | BODYWORKER'S, BORDERING |
| AH10761 | 78 | RIVETING |
| AH10762 | 79 | SLEDGE, BLACKSMITH'S CROSS-PEEN FRENCH TYPE |
| DR03051 | 8 | SLEDGE, BLACKSMITH'S DOUBLE-FACED |
| DR03075 | 80 | BODYWORKER'S PLANISHING SINGLE FACE |
| DR03076 | 80A | BODYWORKER'S PLANISHING SINGLE FACE |
| AH10764 | 81 | ELECTRICIAN'S |
| DR03052 | 8A | SLEDGE, BLACKSMITH'S OR ENGINEER'S DOUBLE FACED |
| AH10697 | 9 | ENGINEER'S, CROSS-PEEN |
AHRU*JHEAD WEIGHT
A RELATIVE MEASURE OF THE MASS OF A HEAD WITH RESPECT TO ITS DENSITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHRUJAZ2.0*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AZ | GRAMS |
| BA | KILOGRAMS |
| AY | OUNCES |
| AX | POUNDS |
ASHR*JWEIGHT
A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASHRJAX2.0*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AZ | GRAMS |
| BA | KILOGRAMS |
| AY | OUNCES |
| AX | POUNDS |
AHRZ*DFACE MATERIAL
THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT.
Enter the applicable reply code from the table below
(AHRZDALA000*;AHRZDSTA000$DALB000*;AHRZDSTA000$$DALB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| FEC000 | IRON MALLEABLE |
| PBA000 | LEAD |
| LRA000 | LEATHER |
| PCA000 | PLASTIC |
| PCN000 | PLASTIC PHENOLIC |
| PCAR00 | PLASTIC POLYTRIFLUOROETHYLENE |
| PCAP00 | PLASTIC VINYL |
| RCE000 | RUBBER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| SNB000 | TIN |
| WDC000 | WOOD |
AASV*JHEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASVJAC2.0*;AASVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ARGG*JFACE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FACE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARGGJAA2.0*;ARGGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFCK*;CBBLDBCN$DFCF*;CBBLDBCN$$DFCF*)
| Table 1 |
| Reply Code (AN47) | Reply |
| FCF | DOUBLE INSULATED |
| BCN | INSULATED |
| FCJ | LEATHER HANDLE GRIP |
| DQG | MAGNETIC |
| BKW | NONMAGNETIC |
| AHJ | NONSPARKING |
| FCK | RUBBER HANDLE GRIP |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDNR*;ENACDNZ$$DNR*)
| Table 1 |
| Reply Code (EN02) | Reply |
| NZ | PLASTICS REMOVAL IN THE MARINE ENVIRONMENT (PRIME) PRODUCT |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information