FSC Information

4020	Fiber Rope, Cordage, and Twine

Colloquial Information

No Colloquials assigned to this Approve Item Name at this time

Change List

MRC AMXF has been deleted

MRC AJRS has been deleted

NAMEDITEM NAME

NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.

Enter the item name code.

(NAMED05026*)

ADAVJOVERALL DIAMETER

A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABRYJLENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABRYJFA2.0*;ABRYJFA2.0$$JFA2.1*)

Table 1
	Reply Code (AA05)	Reply
	F	FEET
	M	METERS
	Y	YARDS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AARX*JINSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AARXJAB2.0*;AARXJAB2.0$JAB2.0*;AARXJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABHP*JOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJLC2.0*;ABHPJLC2.0$JLC2.0*;ABHPJLC2.0$$JLC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABVV*JPIN DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABVVJLC2.0*;ABVVJLC2.0$JLC2.0*;ABVVJLC2.0$$JLC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ACVU*JSTOCK DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STOCK,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ACVUJLA2.0*;ACVUJLA2.0$JLA2.0*;ACVUJLA2.0$$JLA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADJT*JINSIDE WIDTH

AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADJTJAA2.0*;ADJTJAA2.0$JAA2.0*;ADJTJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADJU*JINSIDE LENGTH

A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADJUJAA2.0*;ADJUJAA2.0$JAA2.0*;ADJUJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGCW*JWIRE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AGCWJLC2.0*;AGCWJLC2.0$JLC2.0*;AGCWJLC2.0$$JLC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AHMS*JUPPER LOOP INSIDE DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AHMSJAA2.0*;AHMSJAA2.0$JAA2.0*;AHMSJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CTZR*JDISTANCE FROM BAIL CENTER TO HOLE CENTER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CTZRJAA2.0*;CTZRJAA2.0$JAA2.0*;CTZRJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AHMT*JLOWER LOOP INSIDE DIAMETER

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AHMTJAB2.0*;AHMTJAB2.0$JAB2.0*;AHMTJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AHNS*JLEG END THICKNESS

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AHNSJAA2.0*;AHNSJAA2.0$JAA2.0*;AHNSJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AJRE*JBEARING SURFACE TO BEARING SURFACE DISTANCE

NONE.MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJREJAA2.0*;AJREJAA2.0$JAA2.0*;AJREJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AJRP*JINSIDE WIDTH BETWEEN EYES

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJRPJLA2.0*;AJRPJLA2.0$JLA2.0*;AJRPJLA2.0$$JLA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BRYZ*JDISTANCE ACROSS THROAT

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BRYZJAA2.0*;BRYZJAA2.0$JAA2.0*;BRYZJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AARN*DFABRICATION METHOD

THE PROCESS USED IN MANUFACTURING THE ITEM.

Enter the applicable reply code from the table below

(AARNDAB*;AARNDFT$DAY*)

Table 1
	Reply Code (AA62)	Reply
	AB	BRAIDED
	HY	CABLE LAID
	FT	PLAITED
	AY	TWISTED
	AW	WOVEN

AJXN*JBREAKING STRENGTH

THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJXNJNTA2.0*;AJXNJNTA2.0$$JNTA2.1*)

Table 1
	Reply Code (AB16)	Reply
	DN	DECANEWTONS
	KL	KILOGRAMS
	NT	NEWTONS
	LB	POUNDS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

APEA*DSURFACE CONDITION

THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. PLEASE USE MRC SFCD IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable reply code from the table below

(APEADBBD)

Table 1
	Reply Code (AK39)	Reply
	A	ANY ACCEPTABLE
	BGZ	BONDED
	BAQ	GLAZED
	BCZ	MERCERIZED
	BBD	NATURAL
	AAX	POLISHED
	BDE	SOFT
	BHA	WAXED

MATT*DMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(MATT3HOUDPCY000*;MATT3HOUDPCY000$DFBL000*;MATT3HOUDPCY000$$DFBL000*)

Table 1
	ISAC Field Indicator (5000)	Location
	3ACN	CORE
	3AEE	OVERALL
	3BAE	SOCKET
	3BDO	RING
	3DMY	ALL ATTACHMENTS
	3DNA	FIRST INTERMEDIATE ATTACHMENT
	3DNB	SECOND INTERMEDIATE ATTACHMENT
	3DNC	THIRD INTERMEDIATE ATTACHMENT
	3DND	FOURTH INTERMEDIATE ATTACHMENT
	3DNE	FIFTH INTERMEDIATE ATTACHMENT
	3DNS	SECOND TERMINAL ATTACHMENT FIRST END
	3DNT	THIRD TERMINAL ATTACHMENT FIRST END
	3DNU	FOURTH TERMINAL ATTACHMENT FIRST END
	3DNV	SECOND TERMINAL ATTACHMENT SECOND END
	3DNW	THIRD TERMINAL ATTACHMENT SECOND END
	3DNX	FOURTH TERMINAL ATTACHMENT SECOND END
	3DNY	ROPE
	3DNZ	THIMBLE
	3DOA	FIRST TERMINAL ATTACHMENT FIRST END
	3DOB	FIRST TERMINAL ATTACHMENT SECOND END
	3HOU	LOCATION NOT OTHERWISE SPECIFIED
	3JCN	FIFTH TERMINAL ATTACHMENT FIRST END
	3JCP	FIFTH TERMINAL ATTACHMENT SECOND END

Table 2
	Reply Code (MA01)	Reply
	ALA000	ALUMINUM
	CUB000	COPPER ALLOY
	CCA000	COTTON
	FBA000	FIBER
	FBL000	HEMP
	AAA013	MANILA
	PCA000	PLASTIC
	PCCX00	PLASTIC ARAMID
	PCP000	PLASTIC POLYAMIDE (NYLON)
	PCW000	PLASTIC POLYESTER
	PCX000	PLASTIC POLYETHYLENE
	PCY000	PLASTIC POLYETHYLENE TEREPHTHALATE (PET)
	PCAB00	PLASTIC POLYOLEFIN
	PCAC00	PLASTIC POLYPROPYLENE
	PCDA01	POLYAMIDE NYLON
	PCX002	POLYETHYLENE TEREPHTHALATE GLYCOL (PETG)
	RCB000	RUBBER SYNTHETIC
	STA000	STEEL
	ST1035	STEEL COMP 1035
	ST0304	STEEL COMP 304

Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.

MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION

THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.

Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.

(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)

Table 1
	ISAC Field Indicator (5000)	Location
	3ACN	CORE
	3AEE	OVERALL
	3BAE	SOCKET
	3BDO	RING
	3DMY	ALL ATTACHMENTS
	3DNA	FIRST INTERMEDIATE ATTACHMENT
	3DNB	SECOND INTERMEDIATE ATTACHMENT
	3DNC	THIRD INTERMEDIATE ATTACHMENT
	3DND	FOURTH INTERMEDIATE ATTACHMENT
	3DNE	FIFTH INTERMEDIATE ATTACHMENT
	3DNS	SECOND TERMINAL ATTACHMENT FIRST END
	3DNT	THIRD TERMINAL ATTACHMENT FIRST END
	3DNU	FOURTH TERMINAL ATTACHMENT FIRST END
	3DNV	SECOND TERMINAL ATTACHMENT SECOND END
	3DNW	THIRD TERMINAL ATTACHMENT SECOND END
	3DNX	FOURTH TERMINAL ATTACHMENT SECOND END
	3DNY	ROPE
	3DNZ	THIMBLE
	3DOA	FIRST TERMINAL ATTACHMENT FIRST END
	3DOB	FIRST TERMINAL ATTACHMENT SECOND END
	3HOU	LOCATION NOT OTHERWISE SPECIFIED
	3JCN	FIFTH TERMINAL ATTACHMENT FIRST END
	3JCP	FIFTH TERMINAL ATTACHMENT SECOND END

Table 2
	Reply Code (AP33)	Reply
	Q	AEROSPACE MATERIAL SPEC STD
	J	AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
	G	ASSN STD
	A	COMMERCIAL ITEM DESCRIPTION
	K	DEF STAN/SPEC
	B	FED SPEC
	C	FED STD
	L	GOVERNMENT STD/SPEC
	N	INTERNATIONAL STD/SPEC
	F	MFR REF
	D	MIL SPEC
	E	MIL STD
	H	NATIONAL SPEC
	P	NATIONAL STD
	M	NATIONAL STD/SPEC

Table 3
	Reply Code (AP18)	Reply
	M	10TH MATERIAL RESPONSE
	N	11TH MATERIAL RESPONSE
	P	12TH MATERIAL RESPONSE
	Q	13TH MATERIAL RESPONSE
	R	14TH MATERIAL RESPONSE
	S	15TH MATERIAL RESPONSE
	T	16TH MATERIAL RESPONSE
	U	17TH MATERIAL RESPONSE
	W	18TH MATERIAL RESPONSE
	X	19TH MATERIAL RESPONSE
	B	1ST MATERIAL RESPONSE
	Y	20TH MATERIAL RESPONSE
	Z	21ST MATERIAL RESPONSE
	V	22ND MATERIAL RESPONSE
	C	2ND MATERIAL RESPONSE
	D	3RD MATERIAL RESPONSE
	E	4TH MATERIAL RESPONSE
	F	5TH MATERIAL RESPONSE
	H	6TH MATERIAL RESPONSE
	J	7TH MATERIAL RESPONSE
	K	8TH MATERIAL RESPONSE
	L	9TH MATERIAL RESPONSE
	G	ALL MATERIAL RESPONSES
	A	SINGLE MATERIAL RESPONSE

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

AFJQ*JSTORAGE TEMP RANGE

THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.

(AFJQJFM32.0/P50.0*)

Table 1
	Reply Code (AB36)	Reply
	C	CELSIUS
	F	FAHRENHEIT

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

AFJF*DSPECIFIC USE

THE REQUIRED PURPOSE OR APPLICATION FOR WHICH THE ITEM IS DESIGNED.

Enter the applicable reply code from the table below

(AFJFDLS*;AFJFDQF$DQE*)

Table 1
	Reply Code (AD34)	Reply
	QA	BASTING
	LP	BRAIDING
	QB	CARPET STITCHING
	LQ	COIL WINDING MACHINE
	QC	CROCHETING
	QD	DARNING
	LR	HAND KNITTING
	QE	HEAVY LEATHER
	LS	LUBRICATING
	QF	RUG WEAVING
	LT	WEAVING

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

This MRC replaced MRC ZZZP

The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.

PDNB*APURCHASE DESCRIPTION IDENTIFICATION

THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.

Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.

(PDNBA81A37-30624A*)

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

PPRM*BPOST-CONSUMER RECOVERED MATERIALS PERCENTAGE

THE PERCENTAGE OF THE POST-CONSUMER RECOVERED OR RECYCLED MATERIAL INCLUDED IN THE ITEM.

Enter a reply with a minimum of one digit on either side of the decimal point.

(PPRMB2.0)

ENVA*DENVIRONMENTAL ATTRIBUTE

THE SPECIFIC ATTRIBUTE OF THE ITEM THAT QUALIFIES IT AS AN ENVIRONMENTALLY PREFERABLE PRODUCT.

Enter the applicable reply code from the table below

(ENVADAAG)

Table 1
	Reply Code (EN00)	Reply
	AAG	CONTAINS RECYCLED MATERIAL

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)