Two or more lampholders having a common mounting or mounted on each other. It may include switches or dropping resistors, provided these items control the lamps only. Excludes:FIXTURE, LIGHTING.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED04585*)
AHGFALAMPHOLDER QUANTITY
THE NUMBER OF LAMPHOLDERS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AHGFA10*)
AARAATERMINAL QUANTITY
THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARAA10*)
AEUHALAMP ACCOMMODATION QUANTITY
THE NUMBER OF LAMPS THAT CAN BE ACCOMMODATED BY THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEUHA10*)
AEUJDLAMP BASE TYPE ACCOMMODATED
INDICATES THE TYPE OF LAMP BASE THE ITEM WILL ACCOMMODATE.
Enter the applicable reply code from the table below
(AEUJDCB*;AEUJDCL$DDK*)
| Table 1 |
| Reply Code (AD36) | Reply |
| AA | ADMEDIUM SCREW |
| AB | ADMEDIUM SCREW SKIRTED |
| LG | B15D/19 |
| FW | B15D/24X17 |
| FX | B15D/27X22 |
| FY | B15D/29X26 |
| LH | B15S/19 |
| GA | B15S/24X17 |
| GB | B15S/27X22 |
| GC | B15S/29X26 |
| LK | B22D/22 |
| GD | B22D/25X26 |
| LJ | B22D-3/25X26 |
| GE | B22D-54 |
| GF | B22D-68 |
| LL | B22S/22 |
| LF | B9.5S/11 |
| LQ | BA15D |
| LR | BA15S |
| FL | BA20D |
| FM | BA20S |
| FN | BA21D-3 |
| FP | BA21S-3 |
| LM | BA7S/11 |
| LN | BA9S/13 |
| LP | BA9S/14 |
| FQ | BAY 15D |
| FR | BAY 15S |
| AE | BRASS FERRULE |
| GJ | BY22D |
| AF | CANDELABRA SCREW |
| AG | CANDELABRA SCREW SKIRTED |
| AH | CARTRIDGE TWO PIN POLARIZED |
| AJ | CERAMIC TUBULAR WITH FLEXIBLE WIRE LEADS |
| FC | DISK |
| AK | DISK LUMILINE |
| AL | DISK WITH THREE SOLDERING PINS, 1 1/8 INCH DIA. |
| AM | DISK WITH THREE SOLDERING PINS, 1 3/8 INCH DIA. |
| AN | DISK WITH THREE WIRE LEADS |
| AP | DOUBLE CONTACT BAYONET CANDELABRA |
| AQ | DOUBLE CONTACT BAYONET CANDELABRA EXPORT |
| AR | DOUBLE CONTACT BAYONET CANDELABRA INDEXING |
| AS | DOUBLE CONTACT BAYONET CANDELABRA SKIRTED |
| AT | DOUBLE CONTACT BAYONET PINLESS |
| AU | DOUBLE CONTACT CANDELABRA PREFOCUS |
| AV | DOUBLE CONTACT MEDIUM BAYONET EXPORT |
| AW | DOUBLE CONTACT MEDIUM RING |
| AX | DOUBLE CONTACT MINATURE FLANGED |
| AY | DOUBLE INTERMEDIATE SCREW |
| AZ | DOUBLE SLIDE |
| LT | E10/12 |
| LW | E10/13 |
| JE | E10/19X13 |
| LX | E12/15 |
| LY | E12/20X15 |
| LZ | E14/20 |
| JG | E14/23X15 |
| JH | E14/25X17 |
| MA | E17/20 |
| MB | E26/24 |
| KS | E26D |
| MC | E27/25 |
| MD | E27/27 |
| JJ | E27/51X39 |
| HN | E27-3 FIN PREFOCUS |
| ME | E39/41 |
| MF | E40/41 |
| MG | E40/45 |
| JD | E5/15X6 |
| LS | E5/9 |
| MH | EP10/14X11 |
| BA | EXTENDED MOGUL END PRONG WITH CERAMIC BLOCK |
| KD | FA4 |
| GQ | FA6 |
| GR | FC6.4-0.8 |
| BB | FERRULE CONTACT |
| BC | FLEXIBLE STRAP |
| BD | FLEXIBLE WIRE LEADS |
| FE | FOUR PIN |
| BE | FOUR PIN CIRCLINE |
| BF | FOUR PIN INDEXING |
| KW | G10Q |
| MN | G16T/23X22 |
| MP | G17Q-7-FOUR PIN INDEXING |
| GP | G19 |
| HG | G22 |
| KL | G38 |
| GK | G4 |
| GL | G5.3 |
| MJ | G6.35 - 15 |
| MK | G6.35 - 20 |
| ML | G6.35 - 25 |
| MM | G6.35 - 30 |
| GN | G9.5 |
| BG | GIANT FIVE PIN |
| BH | GLASS GROOVE |
| BJ | GUNSIGHT SCREW |
| MW | GX17Q-7-FOUR PIN INDEXING |
| MQ | GX6.35 - 15 |
| MR | GX6.35 - 20 |
| MS | GX6.35 - 25 |
| MT | GX6.35 - 30 |
| HJ | GX9.5 |
| HM | GY16 |
| NA | GY17Q-7-FOUR PIN INDEXING |
| MX | GY6.35 - 15 |
| MY | GY6.35 - 20 |
| MZ | GY6.35 - 25 |
| NY | GY6.35 - 30 |
| HL | GY9.5 |
| FB | INSTRUMENT SLIDE |
| NB | INSULATED KOLLSMAN SCREW |
| BK | INSULATED SLEEVE WITH FLEXIBLE WIRE LEADS |
| BL | INTERMEDIATE SCREW |
| BM | INTERMEDIATE SCREW EXPORT |
| BN | KNURLED SCREW |
| NC | KOLLSMAN SCREW |
| AC | LARGE INDEX RING |
| BQ | LARGE THREE PIN |
| BR | LOCKING FOUR PIN |
| BS | MEDIUM BIPIN |
| BT | MEDIUM BIPOST |
| BU | MEDIUM PREFOCUS |
| BV | MEDIUM SCREW |
| BW | MEDIUM SCREW EXPORT |
| BX | MEDIUM SCREW SKIRTED |
| BY | MEDIUM SIDE PRONG |
| BZ | METAL SLEEVE WITH FLEXIBLE WIRE LEADS |
| CA | MIDGET FLANGED |
| CB | MIDGET GROOVED |
| CC | MIDGET SCREW |
| CD | MINIATURE BAYONET |
| CE | MINIATURE BAYONET PINLESS |
| CF | MINIATURE BAYONET SKIRTED |
| CG | MINIATURE BIPIN |
| CH | MINIATURE CANDELABRA SCREW |
| CJ | MINIATURE CAP CONICAL END |
| CK | MINIATURE CAP CYLINDRICAL END |
| CL | MINIATURE PINLESS |
| CM | MINIATURE SCREW |
| CN | MINIATURE TWO PIN |
| CP | MOGUL BIPIN |
| CQ | MOGUL BIPOST |
| CR | MOGUL END PRONG |
| CS | MOGUL END PRONG WITH CERAMIC BLOCK |
| CT | MOGUL PREFOCUS |
| CU | MOGUL SCREW |
| CV | MOGUL SCREW EXPORT |
| CW | MOUNTING LUGS-BEADED WIRE LEADS |
| CX | OCTAL FIVE PIN |
| CY | OCTAL THREE PIN |
| CZ | OVAL SMALL FOUR PIN |
| HR | P14.5S |
| HS | P18S |
| HT | P28D |
| ND | P28S/24 |
| NE | P28S/33 |
| HY | P36D |
| HZ | P36S |
| NF | P38S |
| NG | P38S WITH 3 FLATS |
| NH | P40S/41 |
| NJ | P40S/55 |
| NK | P43T-38 |
| NL | P45T-41 |
| KN | P46S WITH 3 FLATS |
| JB | PG22-6.35 |
| JC | PK22S |
| FD | POLARIZED SUBMINIATURE BIPIN |
| DA | RADIO FOUR PIN |
| DB | RECESSED DOUBLE CONTACT |
| DC | RECESSED SINGLE CONTACT |
| DD | RECTANGULAR RECESSED SINGLE CONTACT |
| JY | S12S |
| NP | S5.5S |
| NQ | S5.7S/8 |
| KJ | SIDE CLIPS |
| KK | SIDE CLIPS AND COLORED END |
| DE | SINGLE CONTACT BAYONET CANDELABRA |
| DF | SINGLE CONTACT BAYONET CANDELABRA EXPORT |
| DG | SINGLE CONTACT BAYONET CANDELABRA INDEXING |
| DH | SINGLE CONTACT BAYONET CANDELABRA PINLESS |
| DJ | SINGLE CONTACT CANDELABRA PINLESS |
| DK | SINGLE CONTACT CANDELABRA PREFOCUS |
| DL | SINGLE CONTACT MEDIUM BAYONET EXPORT |
| DM | SINGLE CONTACT MINIATURE FLANGED |
| FF | SINGLE PIN |
| DN | SINGLE PIN FLUTED |
| AD | SMALL INDEX RING |
| DP | SPADE PIN |
| DQ | SPADE SINGLE CONTACT TERMINAL |
| JR | SPECIAL 1.7X0.35 MM THREAD |
| JM | SPECIAL 10BA THREAD |
| NN | SPECIAL 2 BA THREAD |
| JQ | SPECIAL 2.2X0.45 MM THREAD |
| JP | SPECIAL 4.0X0.70 MM THREAD |
| JN | SPECIAL 5/32 WHIT THREAD |
| JL | SPECIAL 8BA THREAD |
| DV | SPECIAL 952 SCREW |
| DW | SPECIAL 952 SCREW WITH DIMMER SLEEVE |
| JS | SPECIAL 953 SCREW |
| DR | SPECIAL FIVE PIN |
| NM | SPECIAL KOLLSMAN SCREW |
| DS | SPECIAL MINIATURE, ONE AND ONE-HALF TURN THREAD |
| DU | SPECIAL NO.10-64 THREAD |
| DT | SPECIAL SLEEVE |
| DX | SUBMIDGET FLANGED |
| DY | SUBMINIATURE TWO PIN |
| DZ | SURGICAL FLANGE, STYLE 1 |
| NR | SV7/6.8 |
| NS | SV7/8 |
| NT | SV8.5/5 |
| NW | SV8.5/6.5 |
| NX | SV8.5/8 |
| GX | T4.6 |
| GY | T5.5 |
| GZ | T5.5K |
| HA | T5.5KM/ |
| HB | T5.8 |
| HC | T6.5 |
| HD | T6.6 |
| HE | T6.8 |
| HF | T7 |
| EE | TELEPHONE SLIDE NO.ONE |
| EF | TELEPHONE SLIDE NO.TWO |
| EG | TELEPHONE SLIDE SPECIAL |
| EH | THREE CONTACT LUGS |
| EJ | THREE CONTACT MEDIUM BAYONET |
| EK | THREE CONTACT MEDIUM SCREW |
| EL | THREE CONTACT MOGUL SCREW |
| EM | THREE PRONG-TWO PRONG |
| EN | THREE SCREW TERMINALS |
| EP | THREE SLIP-ON TERMINALS |
| EQ | THREE WIRE LEADS |
| EZ | TWO BUTTON |
| ER | TWO CONTACT LUGS |
| FA | TWO PIN PREFOCUS |
| ES | TWO SCREW TERMINALS |
| ET | TWO SLIP-ON TERMINALS |
| EU | UNTHREADED CYLINDER W/SCREW TERMINAL |
| EV | VENTILATED LARGE INDEXING RING |
| KF | W10.6X8.5D |
| LB | W2.1X9.5D |
| KE | W2X4.6D |
| LC | W3.3X10.4D |
| EW | WEDGE |
| EX | WIRE TERMINALS, DOWN |
| EY | WIRE TERMINALS, UP |
| KG | X511 |
IF STYLE/REPLY CODE(s) ACC OR AEG WERE ENTERED FOR MRC CSCF, YOU MUST ANSWER MRC (AHHZ)
CSCFDTERMINAL TYPE
INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the applicable reply code from the table below
(CSCFDAAM*;CSCFDACC$DAFH*;CSCFDACC$$DAFH*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ABL | BINDING POST |
| ADB | CLIP |
| ACN | CONNECTOR, PLUG |
| AAF | CONNECTOR, RECEPTACLE |
| AAH | FERRULE |
| AME | INSULATION PIERCING |
| ABU | MALE PLUG |
| AAM | PIN |
| AFH | PLUG |
| ACZ | QUICK DISCONNECT, MALE |
| ABQ | SCREW |
| ATQ | SCREW W/SOLDER LUG |
| ASD | SETSCREW |
| AFF | SOLDER LUG |
| AAS | SOLDER STUD |
| ATD | SPIKE |
| AEN | SPRING |
| ABB | TAB, SOLDER LUG |
| ATE | TAB, SOLDERLESS LUG |
| APP | TAPPED HOLE |
| ABC | THREADED HOLE |
| ABD | THREADED STUD |
| ABH | UNTHREADED HOLE |
| ACC | WIRE LEAD |
| AEG | WIRE LEAD W/LUG |
AHHZ*JWIRING PROVISION LENGTH
THE MEASUREMENT OF EACH WIRING PROVISION OF AN ITEM TAKEN FROM THE BODY TO THE ENDS OF THE WIRING PROVISION,INCLUDING ANY TERMINATIONS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHHZJAB2.0*;AHHZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) A1, A2, A3, A4, A5 OR A6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABKV)
IF STYLE/REPLY CODE(s) A22, A29 OR A30 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABKV and ABTB)
IF STYLE/REPLY CODE(s) A7 OR A8 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABNM and ABMK and ABKW)
IF STYLE/REPLY CODE(s) A9, A10, A11, A12, A14, A15, A19, A25, A26, A27, A28, A33, A42, A43, A44, A45 OR A46 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABKV)
IF STYLE/REPLY CODE(s) A34, A35, A36, A37, A38, A39, A40 OR A41 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABKV)
IF STYLE/REPLY CODE(s) A13, A24, A31 OR A32 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABHP and ABMK)
IF STYLE/REPLY CODE(s) A16 OR A23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and ABKW)
IF STYLE/REPLY CODE(s) A17, A18 OR A20 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTH and ABMK and ABKW)
IF STYLE/REPLY CODE(s) A21 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABTH and ABKW)
IF STYLE/REPLY CODE(s) A55 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABTB)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA32*;STYLLA22$$LA43*)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAD1090 | A1 | KEYLESS |
| AAD1099 | A10 | WIRE LEADS |
| AAD1100 | A11 | WIRE LEADS |
| AAD1101 | A12 | WIRE LEADS |
| AAD1102 | A13 | KEYLESS |
| AAD1103 | A14 | RING |
| AAD1104 | A15 | PUSH |
| AAD1105 | A16 | SIGN AND FIXTURE |
| AAD1106 | A17 | SIGN AND FIXTURE |
| AAD1107 | A18 | SIGN AND FIXTURE |
| AAD1108 | A19 | SIGN AND FIXTURE |
| AAD1091 | A2 | PUSH |
| AAD1109 | A20 | SIGN AND FIXTURE |
| AAD1110 | A21 | SIGN AND FIXTURE |
| AAD1111 | A22 | SIGN AND FIXTURE |
| AAD1112 | A23 | GROOVED |
| AAD1113 | A24 | GROOVED |
| AAD1114 | A25 | PLAIN |
| AAD1115 | A26 | PLAIN |
| AAD1116 | A27 | RING |
| AAD1117 | A28 | DIE CAST |
| AAD1118 | A29 | DIE CAST |
| AAD1092 | A3 | KEY |
| AAD1119 | A30 | DIE CAST |
| AAD1120 | A31 | PULL |
| AAD1121 | A32 | KEY LESS |
| AAD1122 | A33 | SIGN ONE PIECE |
| AAD1123 | A34 | CANDELABRA |
| AAD1124 | A35 | CANDELABRA |
| AAD1125 | A36 | SCREW |
| AAD1126 | A37 | CANDELABRA |
| AAD1127 | A38 | CANDELABRA |
| AAD1128 | A39 | CANDELABRA |
| AAD1093 | A4 | PULL |
| AAD1129 | A40 | CANDELABRA |
| AAD1130 | A41 | CANDELABRA |
| AAD1131 | A42 | BAYONET |
| AAD1132 | A43 | CANDLE |
| AAD1133 | A44 | CANDLE |
| AAD1134 | A45 | CANDLE |
| AAD1135 | A46 | CANDLE |
| AAD1094 | A5 | KEYLESS |
| AAD1136 | A55 | THRU-HOLE |
| AAD1095 | A6 | KEYLESS |
| AAD1096 | A7 | W/STARTER SOCKET |
| AAD1097 | A8 | W/O STARTER SOCKET |
| AAD1098 | A9 | KEYLESS |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAB2.0*;ABKVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAC2.0*;ABNMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAC2.0*;ABTBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTH*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES
THE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTHJAB2.0*;ABTHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDCPA)
| Table 1 |
| Reply Code (AB28) | Reply |
| CPA | MOUNTING STRIP |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDRAB*;AXGYDAAE$DAHM*;AXGYDAAE$$DAHM*)
| Table 1 |
| Reply Code (AM39) | Reply |
| ABC | BRACKET |
| ABD | BUSHING |
| CBB | CAM LOCK |
| ABH | CLAMP |
| CBC | CLAMPING BAR |
| AFL | CLIP |
| AFN | CONDUIT |
| BJV | CONNECTOR PLUG |
| AME | CORD GRIP |
| AMF | COUPLING RING |
| BVH | EXTERNAL THREADED |
| EAA | EXTERNALLY THREADED RING |
| ACR | FLANGE |
| GAB | GLUE |
| AMM | GROOVE |
| ACP | HOLE |
| BLA | HOLE FOR SCREW |
| AGG | HOOK |
| BVJ | INTERNAL THREADED |
| BSJ | LOCK RING |
| AHM | LOOP CLAMP |
| AED | PANEL |
| AMS | PENDANT |
| PAC | PENDANT W PORCELAIN BUSHING |
| PAB | PENDANT W/ COMPOSITION BUSHING |
| AAD | PIN |
| APF | PLUG |
| ABS | RETAINER RING |
| RAA | RETAINING EAR |
| RAB | RETAINING PIN |
| ABY | SLOT |
| AJE | SNAP BUTTON |
| AHL | SNAP RING |
| AJG | SNAP-IN CATCH |
| AEF | SOCKET |
| AJH | SPEED NUT |
| ANK | STRIP |
| AAE | STUD |
| ACD | TERMINAL |
| AFA | THREADED BUSHING |
| AKA | THREADED CATCH |
| AHF | THREADED HOLE |
| AHD | TWIST LOCK |
| ACQ | UNTHREADED HOLE |
| AKH | V-SPRING |
| AHV | WIRE LEAD |
| BBP | YOKE |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAC*;BBRGDAE$DAC*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AE | GENERAL PURPOSE WAREHOUSE |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDZNA000*;SFTT3AEEDZNA000$DANA000*;SFTT3AEEDZNA000$$DANA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3BBP | SHELL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| ENA000 | ENAMEL |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| AGA000 | SILVER |
| ZNA000 | ZINC |
CQRG*DBODY MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BODY IS FABRICATED.
Enter the applicable reply code from the table below
(CQRGDPCG000*;CQRGDPCA000$DST1009*;CQRGDPCA000$$DST1009*)
| Table 1 |
| Reply Code (MA01) | Reply |
| PCA000 | PLASTIC |
| PCG000 | PLASTIC DIALLYL PHTHALATE |
| ST1009 | STEEL COMP 1009 |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3BCVDPCM000*;MATT3BCVDPCM000$DPCJ000*;MATT3BCVDPCM000$$DPCJ000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3BBP | SHELL |
| 3BCV | MOUNTING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CSA000 | CELLULOSE |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0091 | COPPER ALLOY 360 |
| CU0104 | COPPER ALLOY 511 |
| FBA000 | FIBER |
| GSA000 | GLASS |
| NLA000 | NICKEL |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCH000 | PLASTIC EPOXY |
| PCJ000 | PLASTIC MELAMINE |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| CLB000 | PORCELAIN |
| RCE000 | RUBBER |
| STA000 | STEEL |
| ST0303 | STEEL COMP 303 |
| STB000 | STEEL CORROSION RESISTING |
| WDC000 | WOOD |
| ZNB000 | ZINC |
AHGG*ALAMPHOLDER MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE LAMPHOLDER.
Enter the alpha-numeric reply with five character(s) exactly.
(AHGGAE4J7X)
AHGH*ALAMPHOLDER MANUFACTURER PART NUMBER
THE IDENTIFYING PART NUMBER ASSIGNED TO THE LAMPHOLDER BY THE MANUFACTURER.
Enter the alpha-numeric reply with a minimum of one character.
(AHGHAA0)
ELEC*BVOLTAGE IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ELECB2.0*;ELECB2.0$$BM2.0*)
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0*;AMPSB2.0$$BM2.0*)
ABJL*BWATTAGE RATING IN WATTS
THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ABJLB2.0*;ABJLB2.0$$BM2.0*)
AHGJ*DMOUNTING FEATURE TYPE
INDICATES THE TYPE OF FEATURE USED TO MOUNT THE ITEM.
Enter the applicable reply code from the table below
(AHGJDB*;AHGJDC$DA*;AHGJDC$$DA*)
| Table 1 |
| Reply Code (AF30) | Reply |
| A | ANY ACCEPTABLE |
| B | FLUSH |
| C | SURFACE |
ACUP*AMOUNTING DEVICE QUANTITY
THE NUMBER OF MOUNTING DEVICES USED AS A MEANS OF ATTACHING THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACUPA10*)
IF STYLE/REPLY CODE(s) B1 OR B15 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (ABRY and AKQJ and AKQK and ABGL)
IF STYLE/REPLY CODE(s) B2 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (AKQK and HGTH and ABGL)
IF STYLE/REPLY CODE(s) B3, B9 OR B14 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (HGTH and ABVG and ABGL and ABTD)
IF STYLE/REPLY CODE(s) B4, B6, B8, B10 OR B13 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (HGTH and ABTD and ABVG and ABGL and AKQK)
IF STYLE/REPLY CODE(s) B5 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (AKQK and ABGL and HGTH and ABRY)
IF STYLE/REPLY CODE(s) B7 OR B11 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (AKQK and AKQJ and ABGL and HGTH)
IF STYLE/REPLY CODE(s) B12 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (AKQJ and HGTH and AKQK and ABRY)
IF STYLE/REPLY CODE(s) B16 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (ABRY and ABVG and ABGL and ABTD)
IF STYLE/REPLY CODE(s) B17 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (AKQK and ABGL and ABRY)
IF STYLE/REPLY CODE(s) B18 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (HGTH and AKQK and ABRY)
IF STYLE/REPLY CODE(s) B19 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (HGTH and ABVG and AKQK and ABTD)
IF STYLE/REPLY CODE(s) B20 OR B21 WERE ENTERED FOR MRC CRWG, YOU MUST ANSWER MRC (ABGL and HGTH)
CRWG*LMOUNTING BRACKET STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING BRACKET.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CRWGLB7)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAD1137 | B1 | DOWN |
| AAD1146 | B10 | UP |
| AAD1147 | B11 | UP |
| AAD1148 | B12 | UP |
| AAD1149 | B13 | UP |
| AAD1150 | B14 | UP |
| AAD1151 | B15 | STRAIGHT |
| AAD1152 | B16 | STRAIGHT |
| AAD1153 | B17 | STRAIGHT |
| AAD1154 | B18 | LEFT |
| AAD1155 | B19 | RIGHT |
| AAD1138 | B2 | DOWN |
| AAD1156 | B20 | SPRING TENSION |
| AAD1157 | B21 | SPRING TENSION |
| AAD1139 | B3 | DOWN |
| AAD1140 | B4 | DOWN |
| AAD1141 | B5 | DOWN |
| AAD1142 | B6 | DOWN |
| AAD1143 | B7 | DOWN |
| AAD1144 | B8 | UP |
| AAD1145 | B9 | UP |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAB2.0*;ABGLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAA2.0*;ABVGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKQJ*JCENTER TO CENTER DISTANCE BETWEEN BRACKET MOUNTING HOLES
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKQJJAB2.0*;AKQJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKQK*JBRACKET MOUNTING HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKQKJAB2.0*;AKQKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HGTH*JHEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(HGTHJAA2.0*;HGTHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) C1, C2, C4, C6, C7, C8, C9, C10, C11 OR C12 WERE ENTERED FOR MRC AJUX, YOU MUST ANSWER MRC (AEUR and AHGK)
IF STYLE/REPLY CODE(s) C3 OR C5 WERE ENTERED FOR MRC AJUX, YOU MUST ANSWER MRC (AEUS and AEUR)
IF STYLE/REPLY CODE(s) C13 WERE ENTERED FOR MRC AJUX, YOU MUST ANSWER MRC (AEUS and AHGK)
AJUX*LMOUNTING CLIP STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING CLIP.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AJUXLC10)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAD1158 | C1 | UP |
| AAD1167 | C10 | DOWN |
| AAD1168 | C11 | DOWN |
| AAD1169 | C12 | DOWN & UNDER |
| AAD1170 | C13 | STRAIGHT & UNDER |
| AAD1159 | C2 | UP |
| AAD1160 | C3 | UP |
| AAD1161 | C4 | UP |
| AAD1162 | C5 | UP |
| AAD1163 | C6 | UP |
| AAD1164 | C7 | UP |
| AAD1165 | C8 | UP |
| AAD1166 | C9 | UP |
AEUR*JCLIP HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEURJAB2.0*;AEURJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEUS*JCLIP LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEUSJAA2.0*;AEUSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHGK*JCLIP WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHGKJAC2.0*;AHGKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDAI*;ABFEDCH$DAP*;ABFEDCH$$DAP*)
| Table 1 |
| Reply Code (AB27) | Reply |
| AA | ACID RESISTANT |
| A | ANY ACCEPTABLE |
| AB | CEMENT TIGHT |
| DJ | CORROSION RESISTANT |
| FS | DRIPTIGHT |
| AC | DRIPTIGHT-NEMA TYPE 2 |
| CF | DUSTPROOF |
| AD | DUSTPROOF-NEMA TYPE 13 |
| DY | DUSTTIGHT |
| AE | DUSTTIGHT-NEMA TYPE 5 |
| CE | EXPLOSION PROOF |
| FA | EXPLOSION PROOF NEC CL. I, GP. CD |
| AF | EXPLOSION PROOF NEC CL.I, GP.ABCD;CL.II, GP.EFG;CL.III |
| AH | EXPLOSION PROOF NEC CL.I, GP.BC;CL.II, GP.EFG;CL.III |
| AG | EXPLOSION PROOF NEC CL.I, GP.BCD;CL.II, GP.EFG;CL.III |
| AJ | EXPLOSION PROOF NEC CL.I, GP.CD;CL.II, GP.EFG;CL.III |
| AL | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.EFG |
| AK | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.EFG;CL.III |
| AM | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.G |
| AN | EXPLOSION PROOF NEC CL.II, GP.EFG;CL.III |
| DK | FUNGUS PROOF |
| CH | FUNGUS RESISTANT |
| AT | GASTIGHT |
| AP | GENERAL PURPOSE-NEMA TYPE 1 |
| BR | MOISTURE RESISTANT |
| N | NOT RATED |
| CJ | OILTIGHT |
| AQ | OILTIGHT-NEMA TYPE 11 |
| EM | RAINTIGHT |
| AR | RAINTIGHT-NEMA TYPE 3R |
| DZ | SUBMERSIBLE |
| AS | SUBMERSIBLE-NEMA TYPE 6 |
| FM | VIBRATION PROOF |
| CN | WATERTIGHT |
| AU | WATERTIGHT-NEMA TYPE 4 |
| DX | WEATHERPROOF |
| AV | WEATHERPROOF-NEMA TYPE 3 |
AEUU*DACCESSORY MOUNTING PROVISION
THE PROVISIONS FURNISHED FOR MOUNTING ACCESSORIES IN OR ON THE ITEM.
Enter the applicable reply code from the table below
(AEUUDF*;AEUUDE$DD*;AEUUDE$$DD*)
| Table 1 |
| Reply Code (AD37) | Reply |
| B | GROOVE |
| D | INTEGRAL SHADE HOLDER |
| H | LEDGE |
| E | METAL CLIP |
| F | RIM |
| G | SQUARE SHANK |
| C | THREAD |
AHGL*AMOUNTING STRIP MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE MOUNTING STRIP.
Enter the alpha-numeric reply with five character(s) exactly.
(AHGLAS0O2A)
AHGM*AMOUNTING STRIP MANUFACTURER PART NUMBER
THE IDENTIFYING PART NUMBER ASSIGNED TO THE MOUNTING STRIP BY THE MANUFACTURER.
Enter the alpha-numeric reply with a minimum of one character.
(AHGMAF5)
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
AKNA*DINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAH*;AKNADAD$DA*;AKNADAD$$DA*)
| Table 1 |
| Reply Code (AG85) | Reply |
| A | ANY ACCEPTABLE |
| AH | FULLY INCLOSED |
| AD | HERMETICALLY SEALED |
| AB | UNINCLOSED |
AAPL*JTORQUE LOAD RATING
THE ABILITY OF AN ITEM TO WITHSTAND A SPECIFIED TORQUE LOAD WITHOUT FRACTURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAPLJD2.0*)
| Table 1 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| K | CENTIMETER-KILOGRAMS |
| A | INCH-OUNCES |
| G | INCH-POUNDS |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AJCN*DPROTECTIVE STORAGE FEATURE
THE PECULIAR STORAGE FEATURE/S/ REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(AJCNDCV*;AJCNDCZ$DCZ*;AJCNDCZ$$DCZ*)
| Table 1 |
| Reply Code (AA65) | Reply |
| CV | GENERAL PURPOSE |
| CZ | SECURITY |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDB)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CTJS*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMERED BY PACKAGING OR PACKING MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJSJGMC2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| GM | GRAMS |
| KG | KILOGRAMS |
| OZ | OUNCES |
| LB | POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information