Any material specifically designed and constructed to resist deterioration from the action of heat, gas, chemicals or liquids and used to create a tight seal. It is supplied in loose form or in coils, spirals, spools or cut lengths, usually having a square or round cross section. For rubber items having a round cross section, see RUBBER ROUND SECTION. Excludes:ROPE, ASBESTOS; CALKING COTTON; and CALKING LEAD. See also PACKING, PREFORMED; and OAKUM.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED04531*)
ABRYJLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJYB2.0*;ABRYJYB2.0$$JYB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Y | YARDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDRC0017*;MATTDRC0007$DLBD000*;MATTDRC0007$$DLBD000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5056 | ALUMINUM ALLOY 5056 |
| ASA000 | ASBESTOS |
| ASB000 | ASBESTOS CHRYSOTILE |
| WXB000 | BEESWAX |
| CNA000 | CARBON |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CKA000 | CORK |
| CCA000 | COTTON |
| FBX000 | FELT |
| FBA000 | FIBER |
| FG0000 | FIBERGLASS |
| FBT000 | FLAX |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| GFA000 | GRAPHITE |
| LBC000 | GREASE |
| FBL000 | HEMP |
| FEF000 | IRON ALLOY |
| FBK000 | JUTE |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| LRA000 | LEATHER |
| AYA000 | MICA |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| LBD000 | OIL |
| LBA000 | OIL LUBRICATING |
| PPA000 | PAPER |
| LBJ000 | PETROLATUM |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCAAD0 | PLASTIC FLUOROCARBON |
| PCCB00 | PLASTIC NYLON |
| PCP000 | PLASTIC POLYAMIDE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PVFH00 | PLASTIC VINYLIDENE FLUORIDE HEXAFLUOROPROPYLENE |
| RSD000 | RESIN |
| RSC000 | RESIN NATURAL |
| RSA000 | RESIN SYNTHETIC |
| RCE000 | RUBBER |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0022 | RUBBER BUTADIENE-STYRENE CLASS SBR |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RC0013 | RUBBER FLUOROCARBON CLASS FPM |
| RCAH00 | RUBBER FOAM |
| RC0017 | RUBBER ISOBUTYLENE-ISOPRENE CLASS IIR |
| RCA000 | RUBBER NATURAL |
| RCAC00 | RUBBER NEOPRENE |
| RC0020 | RUBBER POLYISOPRENE NATURAL CLASS NR |
| RC0012 | RUBBER POLYMETHYLENE-PERFLUOROALKYLENE CLASS FKM |
| RC0023 | RUBBER POLYSULFIDE CLASS T |
| RCZ000 | RUBBER POLYURETHANE |
| RC0021 | RUBBER SILICONE CLASS Q |
| RCB000 | RUBBER SYNTHETIC |
| SLC000 | SILICON |
| SLK000 | SILICONE |
| ZRV000 | SILICONE SPONGE |
| MSG000 | SPONGE |
| STA000 | STEEL |
| ST0304 | STEEL COMP 304 |
| STB000 | STEEL CORROSION RESISTING |
| SNA000 | TIN ALLOY |
| WLA000 | WOOL |
| WL0014 | WOOL COMP 12R1 |
| WL0021 | WOOL COMP 16R3 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
AASHJMINIMUM TENSILE STRENGTH
THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AASHJL2.0*;AASHJL2.0$$JL2.1*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| L | KILOPASCALS |
| V | POUNDS PER SQUARE INCH |
ABJHJTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
PTRM*BTOTAL RECOVERED MATERIALS PERCENTAGE
THE PERCENTAGE OF THE TOTAL RECOVERED OR RECYCLED MATERIAL, FROM MANUFACTURING PROCESSES OR CONSUMER, INCLUDED IN THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(PTRMB2.0)
PPRM*BPOST-CONSUMER RECOVERED MATERIALS PERCENTAGE
THE PERCENTAGE OF THE POST-CONSUMER RECOVERED OR RECYCLED MATERIAL INCLUDED IN THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(PPRMB2.0)
AARN*DFABRICATION METHOD
THE PROCESS USED IN MANUFACTURING THE ITEM.
Enter the applicable reply code from the table below
(AARNDAD*;AARNDGR$DAN*;AARNDGR$$DAN*)
| Table 1 |
| Reply Code (AA62) | Reply |
| KG | ACCORDION-FOLDED |
| KF | ACCORDION-PLEATED |
| AB | BRAIDED |
| AN | CAST |
| AP | CELLULAR, EXPLODED |
| AQ | CELLULAR, UNEXPLODED |
| AC | COMPRESSED |
| AD | CORRUGATED |
| KH | CRIMPED |
| GR | EXTRUDED |
| AT | LAMINATED |
| DT | LATTICED |
| AX | LOOSE FIBROUS |
| AM | MOLDED |
| EY | OVEREXPANDED |
| AS | ROLLED |
| AU | SHREDDED |
| JZ | SKIVED |
| AR | SOLID |
| AY | TWISTED |
| AW | WOVEN |
| DX | WOVEN LATTICE |
| EX | WRAPPED |
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ211*;HZRDDHAZ276$$DHAZ285*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ007 | ASPHALT |
| HAZ012 | COPPER |
| HAZ211 | GREASE |
| HAZ029 | LEAD |
| HAZ265 | OIL |
| HAZ276 | PETROLEUM |
| HAZ285 | PLASTIC |
| HAZ303 | SILVER |
LBMA*DLUBRICATION MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES WITH WHICH THE ITEM IS LUBRICATED.
Enter the applicable reply code from the table below
(LBMADGFA000*;LBMADPCAF00$DLBD000*;LBMADPCAF00$$DLBD000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ASA000 | ASBESTOS |
| MSB000 | GLYCERIN |
| GFA000 | GRAPHITE |
| LBC000 | GREASE |
| AYA000 | MICA |
| LBD000 | OIL |
| LBE000 | OIL MINERAL |
| LBJ000 | PETROLATUM |
| PCP000 | PLASTIC POLYAMIDE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| MSK000 | TALLOW |
| WXA000 | WAX |
| WXC000 | WAX PARAFFIN |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVL)
IF STYLE/REPLY CODE(s) 2, 3, 4, 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 24, 25, 26, 27, 28, 33, 34 OR 36 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVN and ADWH)
IF STYLE/REPLY CODE(s) 7 OR 30 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVL and ADVN)
IF STYLE/REPLY CODE(s) 21 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVN and ADWH and ADWJ)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVK and ADVL)
IF STYLE/REPLY CODE(s) 29 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABNH and ADVN and ADWH)
IF STYLE/REPLY CODE(s) 31 OR 32 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVK and ADVL and ADVN)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVK and ADVN and ADWH)
IF STYLE/REPLY CODE(s) 37 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADVN and ADWH)
AAGR*LCROSS-SECTIONAL SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAGRL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1416 | 1 | CIRCULAR |
| AAH1425 | 10 | V |
| AAH1426 | 11 | V |
| AAH1427 | 12 | SPECIAL |
| AAH1428 | 13 | U |
| AAH1429 | 14 | U |
| AAH1430 | 15 | U |
| AAH1431 | 16 | SPECIAL |
| AAH1432 | 17 | GROOVED |
| AAH1433 | 18 | V |
| AAH1434 | 19 | V |
| AAH1417 | 2 | TRIANGULAR |
| AAH1435 | 20 | ANGLE |
| AAH1436 | 21 | DELTA |
| AAH1437 | 22 | U |
| AAH1438 | 23 | CIRCULAR W/ CENTER APERTURE |
| AAH1439 | 24 | SQUARE W/ OBLONG APERTURE |
| AAH1440 | 25 | D |
| AAH1441 | 26 | V |
| AAH1442 | 27 | U |
| AAH1443 | 28 | SPECIAL |
| AAH1444 | 29 | ANGLE |
| AAH1418 | 3 | RECTANGULAR |
| AAH1445 | 30 | D |
| AAH1446 | 31 | OPEN EYE |
| AAH1447 | 32 | CLOSED EYE |
| AAH1448 | 33 | SPECIAL |
| AAH1449 | 34 | SPECIAL |
| AAH1450 | 35 | SQUARE W/ CENTER APERTURE |
| AAH1451 | 36 | SQUARE |
| AAH1452 | 37 | CLOSED EYE |
| AAH1419 | 4 | OVAL |
| AAH1420 | 5 | OVAL |
| AAH1421 | 6 | D |
| AAH1422 | 7 | KEYHOLE |
| AAH1423 | 8 | SPECIAL |
| AAH1424 | 9 | U |
ADVK*JCROSS SECTION INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVKJAA2.0*;ADVKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVL*JCROSS SECTION OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVLJAB2.0*;ADVLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVN*JCROSS-SECTIONAL HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A CROSS SECTION,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVNJAA2.0*;ADVNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADWH*JCROSS-SECTIONAL WIDTH
A MEASUREMENT OF THE CROSS SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWHJAC2.0*;ADWHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNH*JMINOR WIDTH
THE SMALLEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNHJAA2.0*;ABNHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADWJ*JANGLE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWJJAA2.0*;ADWJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDEYU)
| Table 1 |
| Reply Code (AN47) | Reply |
| EYU | MEETS/EXCEEDS AFFIRMATIVE PROCUREMENT PROGRAM REQUIREMENTS |
CSXS*JANGLE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSXSJD2.0*;CSXSJD2.0$$JD2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| D | DEGREES |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
IF STYLE/REPLY CODE(s) JH WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (PPRM)
IF STYLE/REPLY CODE(s) JG WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (BDPK)
IF STYLE/REPLY CODE(s) BQ OR BV WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (ALAX)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDBQ*;ENACDJH$$DBV*)
| Table 1 |
| Reply Code (EN02) | Reply |
| JG | ASBESTOS ALTERNATIVE PRODUCTS |
| JH | COMPREHENSIVE PROCUREMENT GUIDELINE - PAPER AND PAPER PRODUCTS - MISCELLANEOUS PAPERS |
| BQ | FILMS - NON-DURABLE - BIOBASED |
| BV | FILMS - SEMI-DURABLE - BIOBASED |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
IF STYLE/REPLY CODE(s) AM WERE ENTERED FOR MRC ECAT, YOU MUST ANSWER MRC (ALAX)
IF STYLE/REPLY CODE(s) AL WERE ENTERED FOR MRC ECAT, YOU MUST ANSWER MRC (BDPK)
IF STYLE/REPLY CODE(s) RC WERE ENTERED FOR MRC ECAT, YOU MUST ANSWER MRC (PPRM)
ECAT*DENVIRONMENTAL ATTRIBUTE CATEGORY
THE CATEGORY THAT DEFINES THIS ITEM'S ENVIRONMENTAL ATTRIBUTE.
Enter the applicable reply code from the table below
(ECATDAM*;ECATDRC$$DAL*)
| Table 1 |
| Reply Code (EN02) | Reply |
| AL | ASBESTOS ALTERNATIVE |
| AM | BIOBASED CONTENT |
| RC | RECYCLED CONTENT |
ALAX*BBIOBASED CONTENT PERCENTAGE
THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALAXB2.0)
BDPK*JASBESTOS CONTENT PERCENTAGE
THE ASBESTOS CONTENT OF THE ITEM,EXPRESSED IN PERCENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDPKJA2.0*;BDPKJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
BDNZ*JDENSITY RATING
AN INDICATION OF THE RATED DENSITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDNZJDB2.0*;BDNZJDB2.0$$JDB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| DB | KILOGRAMS PER CUBIC METER |
| DA | POUNDS PER CUBIC FOOT |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information