An item designed to transmit manual, rotary or linear motion to other devices. May include detachable or nondetachable stud (shaft), pointer, or skirt. It may have reference markings in the form of dots, arrows, hairlines, and/or symbols which may be used in conjunction with a calibrated panel, vernier indicator, and the like to indicate the position or motion of items. For items having spokes or simulated spokes radiating from near the center to near the outside rim of the item and relatively thin round disk-shaped items 3 inches (76.2 mm) in diameter or over, see HANDWHEEL. For items calibrated in units or series of divisions to denote relative positioning of devices see DIAL, CONTROL. Excludes:DOORKNOB; and HANDLE (as modified).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED03263*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDPCR000*;MATTDPCBL00$DPCP000*;MATTDPCBL00$$DPCP000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL0028 | ALUMINUM ALLOY A380.0 |
| CUB000 | COPPER ALLOY |
| FEB000 | IRON CAST |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCD000 | PLASTIC ACRYLIC |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCBN00 | PLASTIC CELLULOSE ACETATE BUTYRATE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX002 | POLYETHYLENE TEREPHTHALATE GLYCOL (PETG) |
| STA000 | STEEL |
| ZSC000 | STEEL ALLOY |
| ST0303 | STEEL COMP 303 |
| STB000 | STEEL CORROSION RESISTING |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) A10 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV)
IF STYLE/REPLY CODE(s) A1, A2, A3, A6, A18, A19, A20, A35 OR A37 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABGL and ABRY and ADUM)
IF STYLE/REPLY CODE(s) A44C WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADUM and ABGL and ABTV)
IF STYLE/REPLY CODE(s) A16 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABGL and ABHA and ADUM)
IF STYLE/REPLY CODE(s) A5 OR A26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABRY and ADUM)
IF STYLE/REPLY CODE(s) A44, A44A OR A44B WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADUM and ABTV and ABKV)
IF STYLE/REPLY CODE(s) A31 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHA and ABKV and ADUM)
IF STYLE/REPLY CODE(s) A4, A7, A8, A9, A4A, A13, A14, A24, A28, A29, A33, A36, A38, A40, A41, A42 OR A38A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ADUM)
IF STYLE/REPLY CODE(s) A11, A12, A17 OR A21 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADUM and ASDB)
IF STYLE/REPLY CODE(s) A15, A22, A23, A27, A32 OR A39 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABGL and ADUM)
IF STYLE/REPLY CODE(s) A46 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABRY)
IF STYLE/REPLY CODE(s) A25 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABRY and ABGL)
IF STYLE/REPLY CODE(s) A43 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADUM and ABRY)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA38A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BK10038 | A1 | BAR |
| BK10047 | A10 | BALL |
| BK10048 | A11 | HEXAGON |
| BK10049 | A12 | OCTAGON |
| BK10050 | A13 | ACORN (DOME) |
| BK10051 | A14 | CROWN |
| BK10052 | A15 | TRIANGULAR |
| BK10053 | A16 | FLUTED FOILS |
| BK10054 | A17 | SQUARE |
| BK10055 | A18 | SQUARE OR RECTANGULAR WITH BAR FACE |
| BK10056 | A19 | CROSS |
| BK10039 | A2 | BAR WITH SINGLE POINTER |
| BK10057 | A20 | TEAR-DROP (EGG-SHAPED) |
| BK10059 | A21 | DECAGON |
| BK10058 | A22 | POINTER |
| BK10060 | A23 | ROUND WITH CRANK |
| BK10061 | A24 | BEEHIVE |
| BK10062 | A25 | ROUND WITH SINGLE POINTER |
| BK10063 | A26 | ROUND WITH CROSS FACE |
| BK10064 | A27 | ROUND WITH EXTENDED BAR FACE |
| BK10065 | A28 | SEMI-BALL |
| BK10066 | A29 | ROUND WITH ARCHED BAR |
| BK10040 | A3 | BAR WITH DOUBLE POINTER |
| BK10067 | A31 | ROUND WITH FLUTED FOILS |
| BK10068 | A32 | POINTED WITH ARCHED BAR |
| BK10069 | A33 | COUNTERSUNK WITH CROWN |
| BK10070 | A35 | RECTANGULAR W/ROUNDED EDGES |
| BK10071 | A36 | ANGULAR SEMI-ROUND |
| BK10072 | A37 | BAR WITH CONCAVE SIDES |
| BK10073 | A38 | SKIRTED/ROUND WITH CONCAVE TOP |
| DQ00035 | A38A | SKIRTED ROUND WITH WINDOW |
| BK10074 | A39 | SKIRTED/ROUND WITH DOUBLE FIN LEVER |
| BK10041 | A4 | ROUND |
| BK10075 | A40 | ROUND WITH FIN LEVER AND SLOTTED BACK |
| BK10076 | A41 | ROUND WITH CROWN |
| BK10077 | A42 | TAPERED WITH COUNTERSUNK FACE |
| BK10078 | A43 | BAR WITH SINGLE POINTER AND FLARED SKIRT |
| BK10079 | A44 | ROUND CONCENTRIC |
| DQ00036 | A44A | SKIRTED ROUND CONCENTRIC |
| DQ00037 | A44B | CONCENTRIC WITH SINGLE FIN LEVER |
| DQ00038 | A44C | CONCENTRIC WITH DOUBLE FIN LEVER |
| BK10081 | A46 | MUSHROOM |
| DQ00034 | A4A | ROUND FLUTED |
| BK10042 | A5 | ROUND WITH FIN LEVER |
| BK10043 | A6 | ROUND WITH BAR LEVER |
| BK10044 | A7 | ROUND WITH BAR FACE |
| BK10045 | A8 | ROUND WITH SINGLE POINTED BAR FACE |
| BK10046 | A9 | ROUND WITH TRIANGULAR FACE |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAA2.0*;ABGLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAC2.0*;ABKVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAB2.0*;ABRYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTV*JKNOB PORTION DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTVJAB2.0*;ABTVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAA2.0*;ADUMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAA2.0*;ASDBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHA*AFLUTED FOIL QUANTITY
THE NUMBER OF CURVED INDENTATIONS SEPARATED BY GROOVES.
Enter the numeric reply with a minimum of one digit.
(ABHAA10*)
IF STYLE/REPLY CODE(s) AB WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ABFR) or (THSD)
IF STYLE/REPLY CODE(s) BT WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ABFR) or (ABFU) or (CBSC) or (THSD)
IF STYLE/REPLY CODE(s) GY WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ABFU) or (CBSC) or (THSD)
IF STYLE/REPLY CODE(s) XX WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ABFX)
IF STYLE/REPLY CODE(s) BQ WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (ABGU)
IF STYLE/REPLY CODE(s) NW, TD OR XR WERE ENTERED FOR MRC ABSX, YOU MUST ANSWER MRC (THSD)
ABSX*DATTACHMENT METHOD
THE MEANS USED TO ATTACH THE ITEM.
Enter the applicable reply code from the table below
(ABSXDCA*;ABSXDAD$DAJ*;ABSXDAD$$DAJ*)
| Table 1 |
| Reply Code (AB47) | Reply |
| CA | CENTER HOLE |
| AB | CLAMP |
| NW | COLLET |
| SW | FLANGE MOUNTED |
| CP | HOLE |
| GY | MACHINE SCREW |
| AC | NUT |
| BQ | PIN |
| AD | PRESS FIT |
| TG | PUSH-ON |
| XR | SCREW ON |
| BT | SETSCREWS |
| CD | SHAFT |
| TD | STUD |
| AJ | THREADED HOLES |
| XT | UNTHREADED COUNTERBORED AND STEPPED HOLE |
| XW | UNTHREADED COUNTERBORED AND TAPERED HOLE |
| XS | UNTHREADED COUNTERBORED HOLE |
| XX | UNTHREADED STUD |
| NQ | WOOD SCREW |
Reference NotesRefer to Reference Drawings when determining reply.
Refer to Reference Drawings for assitance in answering this MRC.
ABFR*ASETSCREW HOLE QUANTITY
THE NUMBER OF SETSCREW HOLES INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ABFRA10*)
CBSC*DSCREW DRIVE TYPE
INDICATES THE TYPE OF DRIVE PROVIDED FOR TURNING,ROTATING,OR POSITIONING THE SCREW.
Enter the applicable reply code from the table below
(CBSCDMF*;CBSCDNE$DKQ*)
| Table 1 |
| Reply Code (AG25) | Reply |
| LR | CROSS RECESS TYPE 1 |
| LS | CROSS RECESS TYPE 11 |
| MH | CROSS RECESS TYPE 1A |
| NC | FOUR SPLINE |
| ND | HEXAGON SOCKET |
| NM | POZIDRIVE |
| NE | SIX SPLINE |
| MF | SLOT |
| KQ | SQUARE SOCKET |
ABFU*JDISTANCE FROM HOLE CENTER TO KNOB/SKIRT BASE
THE DISTANCE FROM THE CENTER OF THE HOLE TO THE BASE OF THE KNOB OR BASE OF SKIRT IF WITH INTEGRALLY MOLDED SKIRT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFUJAB2.0*;ABFUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGU*DPIN ACCOMMODATION TYPE
THE PARTICULAR SHAPE OF THE PIN ACCOMMODATION AND WHETHER OR NOT THE PIN IS INCLUDED.
Enter the applicable reply code from the table below
(ABGUDA)
| Table 1 |
| Reply Code (AB30) | Reply |
| B | STRAIGHT PIN TYPE W/O PIN |
| A | STRAIGHT PIN TYPE W/PIN |
| D | TAPERED PIN TYPE W/O PIN |
| C | TAPERED PIN TYPE W/PIN |
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3AEEDSS*;THSD3AEEDSS$DNJ*;THSD3AEEDSS$$DNJ*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACK | BUSHING |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AZY | RECEPTACLE |
| 3CIN | SCREW HOLE |
| 3CIO | SOCKET INTERNAL |
| 3CIP | SOCKET EXTERNAL |
| 3CIQ | SETSCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| NP | NPT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| NS | UNS |
IF STYLE/REPLY CODE(s) D1 OR D7 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (AGRJ and CRXS)
IF STYLE/REPLY CODE(s) D2 OR D8 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (AGRJ and CSBR and CRXS and AAZT)
IF STYLE/REPLY CODE(s) D3 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (ABGA and ABGF and AGRJ and CRXS)
IF STYLE/REPLY CODE(s) D4 OR D6 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (ADJV and AGRJ and CRXS)
IF STYLE/REPLY CODE(s) D9 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (AATB and CRXS)
IF STYLE/REPLY CODE(s) D10 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (ADJV and CRXS)
IF STYLE/REPLY CODE(s) D12 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (ADJV and AGXF and CRXS)
IF STYLE/REPLY CODE(s) D14 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (AGRJ and CSZB and CRXS)
IF STYLE/REPLY CODE(s) D15 WERE ENTERED FOR MRC ABFX, YOU MUST ANSWER MRC (ABGH and AGRJ and CRXS)
ABFX*LUNTHREADED STUD STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE UNTHREADED STUD.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABFXLD3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BK10026 | D1 | ROUND |
| BK10034 | D10 | SQUARE |
| BK10035 | D12 | RECTANGULAR |
| BK10036 | D14 | TAPERED |
| BK10037 | D15 | STEPPED |
| BK10027 | D2 | ROUND-SLOTTED |
| BK10028 | D3 | ROUND-GROOVE |
| BK10029 | D4 | FLATTED, ONE SIDE |
| BK10030 | D6 | FLATTED, TWO SIDES PARALLEL |
| BK10031 | D7 | SERRATED |
| BK10032 | D8 | SERRATED-SLOTTED |
| BK10033 | D9 | HEXAGON |
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATBJAC2.0*;AATBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZT*JSLOT DEPTH
THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZTJAC2.0*;AAZTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGA*JGROOVE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGAJAB2.0*;ABGAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAA2.0*;ABGFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGH*JSTEP DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGHJAC2.0*;ABGHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJV*JOUTSIDE WIDTH
AN OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJVJAB2.0*;ADJVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGRJ*JSTUD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STUD,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGRJJAA2.0*;AGRJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGXF*JSTUD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE STUD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGXFJAA2.0*;AGXFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRXS*JSTUD OVERALL DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRXSJAB2.0*;CRXSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSBR*JSTUD SLOT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBRJAC2.0*;CSBRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSZB*JSTUD TAPER ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSZBJDC2.0*;CSZBJDC2.0$$JDC2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGJ*JSTEP LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE STEP,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGJJLA2.0*;ABGJJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3AZYJA2.0*;CQJX3AZYJA2.0$JA2.0*;CQJX3AZYJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACK | BUSHING |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AZY | RECEPTACLE |
| 3CIN | SCREW HOLE |
| 3CIO | SOCKET INTERNAL |
| 3CIP | SOCKET EXTERNAL |
| 3CIQ | SETSCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CTTC3ACKJEXT2.0*;CTTC3ACKJEXT2.0$JEXT2.0*;CTTC3ACKJEXT2.0$$JEXT2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACK | BUSHING |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AZY | RECEPTACLE |
| 3CIN | SCREW HOLE |
| 3CIO | SOCKET INTERNAL |
| 3CIQ | SETSCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CMLP3CIOAR0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ACK | BUSHING |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AZY | RECEPTACLE |
| 3CIN | SCREW HOLE |
| 3CIO | SOCKET INTERNAL |
| 3CIP | SOCKET EXTERNAL |
| 3CIQ | SETSCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
ABHG*DGRIPPING SURFACE CONDITION
THE TEXTURE OF THAT PORTION OF THE ITEM WHICH IS DESIGNED TO BE GRASPED.
Enter the applicable reply code from the table below
(ABHGDAAE)
| Table 1 |
| Reply Code (AB32) | Reply |
| AAF | GRIP AID |
| AAE | SMOOTH |
IF STYLE/REPLY CODE(s) E25 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (ADJU and ADJT)
IF STYLE/REPLY CODE(s) E1 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and AAUJ and AAUK and ABSA)
IF STYLE/REPLY CODE(s) E3 OR E4 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and ADJT)
IF STYLE/REPLY CODE(s) E5 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AFMV)
IF STYLE/REPLY CODE(s) E6 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and ABSF and ABSJ)
IF STYLE/REPLY CODE(s) E7 OR E8 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and ABRR and ABRV)
IF STYLE/REPLY CODE(s) E12 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX)
IF STYLE/REPLY CODE(s) E10 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (ADJT and ADJU)
IF STYLE/REPLY CODE(s) E11 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AEJJ and CWBL)
IF STYLE/REPLY CODE(s) E16 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (ADJT)
IF STYLE/REPLY CODE(s) E17 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (ADJT and CTTH)
IF STYLE/REPLY CODE(s) E18 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and AAWY and AAWZ and ABFY)
IF STYLE/REPLY CODE(s) E19 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and ABFY and ABGE and CSKC)
IF STYLE/REPLY CODE(s) E20 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and ABFY and ABSF and ABSJ)
IF STYLE/REPLY CODE(s) E9 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX)
IF STYLE/REPLY CODE(s) E24 WERE ENTERED FOR MRC ABHH, YOU MUST ANSWER MRC (AARX and AAWY and AAWZ and ABFY and ADWA and CTKT)
ABHH*LSHAFT ACCOMMODATION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT ACCOMMODATION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABHHLE5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BK10151 | E1 | SPLINE |
| BK10159 | E10 | RECTANGULAR |
| BK10160 | E11 | SECTOR |
| BK10161 | E12 | INVOLUTE SERRATION |
| BK10162 | E16 | SQUARE |
| BK10163 | E17 | SQUARE WITH DIAGONAL CORNER |
| BK10164 | E18 | COUNTERBORED |
| BK10165 | E19 | TAPERED |
| BK10166 | E20 | INTERNAL KEY ROUND |
| BK10167 | E24 | COUNTERBORED WITH GROOVE |
| BK10168 | E25 | FLATTED THREE SIDES |
| BK10152 | E3 | FLATTED, TWO SIDES PARALLEL |
| BK10153 | E4 | FLATTED ONE SIDE |
| BK10154 | E5 | HEXAGON |
| BK10155 | E6 | KEY |
| BK10156 | E7 | SINGLE KEYWAY |
| BK10157 | E8 | DOUBLE KEYWAY |
| BK10158 | E9 | ROUND |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAC2.0*;AARXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUJ*JSPLINE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUJJAB2.0*;AAUJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUK*JSPLINE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUKJAB2.0*;AAUKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWYJAA2.0*;AAWYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZJAA2.0*;AAWZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAC2.0*;ABFYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGE*JTAPERED END MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGEJAA2.0*;ABGEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRR*JKEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRRJAB2.0*;ABRRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRV*JKEYWAY DEPTH
A MEASUREMENT FROM THE TOP SURFACE TO THE BOTTOM OF THE KEYWAY GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRVJAA2.0*;ABRVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSF*JKEY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSFJAC2.0*;ABSFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSJ*JKEY DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE KEY,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSJJAC2.0*;ABSJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJT*JINSIDE WIDTH
AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJTJAC2.0*;ADJTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJU*JINSIDE LENGTH
A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJUJAC2.0*;ADJUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADWA*JINNER GROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INNER GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWAJAB2.0*;ADWAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJJ*JINSIDE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJJJAC2.0*;AEJJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFMV*JINSIDE WIDTH ACROSS FLATS
A MEASUREMENT OF THE INSIDE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFMVJAB2.0*;AFMVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTKT*JINNER GROOVE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTKTJAB2.0*;CTKTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTTH*JINSIDE WIDTH ACROSS CORNERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTTHJAA2.0*;CTTHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSKC*JTAPER ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSKCJDA2.0*;CSKCJDA2.0$$JDA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWBL*JSECTOR ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWBLJRB2.0*;CWBLJRB2.0$$JRB2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSA*ASPLINE QUANTITY
THE NUMBER OF SPLINES ON OR IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ABSAA10*)
CSKT*DPOINTER DESIGN
INDICATES WHETHER OR NOT THE POINTER IS DESIGNED AS AN INTEGRAL PART OF THE ITEM.
Enter the applicable reply code from the table below
(CSKTDAE)
| Table 1 |
| Reply Code (AH97) | Reply |
| AC | DETACHABLE |
| AE | NONDETACHABLE |
IF YOU ANSWER MRC CRWX, YOU MUST ANSWER MRC (ABSL)
CRWX*DSKIRT DESIGN
INDICATES WHETHER OR NOT THE SKIRT IS DESIGNED AS AN INTEGRAL PART OF THE ITEM.
Enter the applicable reply code from the table below
(CRWXDAC)
| Table 1 |
| Reply Code (AH97) | Reply |
| AC | DETACHABLE |
| AE | NONDETACHABLE |
IF STYLE/REPLY CODE(s) F1, F2, F3 OR F4 WERE ENTERED FOR MRC ABSL, YOU MUST ANSWER MRC (CRPJ)
ABSL*LSKIRT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SKIRT.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABSLLF3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BK10169 | F1 | FLARED |
| BK10170 | F2 | STEPPED |
| BK10171 | F3 | RING |
| BK10172 | F4 | STRAIGHT |
CRPJ*JSKIRT OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRPJJAA2.0*;CRPJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSP*DREFERENCE MARKING
A VISIBLE TRACING OR IMPRESSION,AND THE LIKE,OF ALPHA AND/OR NUMERIC CHARACTERS,SYMBOLS,AND THE LIKE.
Enter the applicable reply code from the table below
(ABSPDNL*;ABSPDES$DHF*;ABSPDES$$DHF*)
| Table 1 |
| Reply Code (AB44) | Reply |
| QX | 1 TO 19 SPACED 15 DEGREES APART |
| KB | 0 THROUGH 2 |
| HK | 0 THROUGH 7 |
| QW | 0 THROUGH 9 |
| QQ | 0 TO 100 |
| LB | 0 TO 7 |
| LC | 0 TO 9 |
| KD | 1 |
| KE | 1 THROUGH 10 |
| RA | 1 THROUGH 4 |
| LH | 1 THROUGH 8 |
| RB | 10 |
| PX | 100 |
| RF | 108 |
| KG | 1K |
| JX | 2 |
| KH | 2K |
| LA | 3 |
| RS | 4 |
| RT | 5 |
| RW | 6 |
| RX | 7 |
| RY | 8 |
| RZ | 9 |
| GP | A |
| HL | A B |
| CG | ADJUSTING KNOB |
| LS | ADJUSTMENT |
| CH | AIR |
| AH | AIR HEATER USE WHILE CRANKING ONLY |
| CJ | ALIGN INPUT |
| CK | ARC |
| BF | ARROW |
| BY | ARROW W/COURSE IN MIDDLE |
| BR | ARROW W/NUMERAL 2 |
| CQ | AUDIO |
| CW | B |
| CZ | BAR SET |
| CY | BAR W/LUMINOUS LINES |
| DA | BARO |
| DB | BOMB OFF |
| DD | BRILL |
| DE | C |
| DF | CAGE |
| DK | CALIBRATION |
| DQ | CHANNEL NO. |
| DR | CHOKE |
| DS | CIRCLE |
| DT | CIRCLE W/X INSIDE |
| DW | CIRCUIT |
| CM | CLOSE |
| BP | CLOSE-OPEN |
| DY | COARSE |
| EB | D |
| EC | DECREASE |
| ED | DETAIL |
| HT | DF |
| EH | DIM |
| EJ | DIRECT |
| EL | DOT |
| EM | DOUBLE ARROW |
| EN | DOWN |
| ES | E |
| EW | ELEV |
| FD | F |
| FE | FEET PER MINUTE |
| FF | FILM SPEED |
| FG | FILTER |
| FJ | FINE |
| FK | FLAP |
| FM | FOCUS |
| FR | FRICTION |
| FS | FRICTION INCREASE |
| DX | FUEL |
| FX | FWD |
| FY | G |
| FZ | GAIN |
| GA | GROOVE |
| BE | HALF INDICATION LINE |
| JC | HDG |
| JD | HDG SET |
| GB | HEAD |
| GC | HEATER |
| GE | HIGH |
| GD | HIGH-LOW |
| NC | INCREASE |
| GG | INCREASE OUTPUT |
| BG | INDEX LINE |
| GH | INDICATING LINE |
| GJ | INDICATOR DOT |
| QJ | INDICATOR LINE |
| BBM | INDICATOR WITH ARROW PAINTED IN YELLOW ORANGE |
| GK | INTENSITY |
| NB | KNOB |
| JF | LEFT |
| BN | LIFT |
| CN | LIGHT |
| GW | LIMIT |
| FL | LINE |
| GX | LOCK |
| GY | LOCK RELEASE |
| LU | LOCK-UNLOCK |
| HC | LOW |
| HF | M |
| LG | MAINSWITCH |
| MT | MARK TIME-ARROW |
| JH | MAX |
| KW | MAX W |
| JJ | MC/115 |
| KX | MICROPHONE |
| KA | N |
| NM | NONE |
| KZ | NORMAL |
| GQ | O |
| HW | OFF |
| FN | OFF-ON |
| CP | ON |
| LK | ONLY |
| CL | OPEN |
| LL | OPEN-CLOSE |
| JY | P |
| LR | PEDAL |
| LW | PITCH |
| EF | POINTER |
| LX | PRESS START |
| PT | PRESS TO TALK |
| MB | PRESS TO TURN |
| MC | PRIMER |
| MG | PULL |
| MD | PULL OUT |
| MH | PULL OUT BEFORE PRESET TUNING |
| LY | PULL STOP |
| MK | PULL TO RESET SWITCH |
| ML | PULL TO TURN |
| GZ | PULL TO UNLOCK |
| MM | PULL TO UNLOCK DELAYED SWEEP |
| MW | PUSH TO DAMP |
| MX | PUSH TO JETT. |
| MY | PUSH TO RELEASE |
| MZ | PUSH TO SET |
| NA | PUSH TO TURN |
| BK | R, 1, 2, 3 |
| AD | R, 2, 3 |
| BJ | RAISED NUMBERS 1 TO 8 EQUALLY SPACED |
| NE | RECLINE |
| NG | RELEASE |
| NH | RETICLE |
| NK | RF |
| NL | RIGHT |
| JP | S |
| PN | S3 |
| JQ | SCALE |
| NN | SCALE IN TENS |
| NP | SCAN |
| NQ | SENSITIVITY |
| JR | SET |
| NT | SIDE |
| NW | SIGNAL |
| NZ | SINGLE DOT |
| PB | SINGLE GROOVE |
| BH | SINGLE LINE |
| PC | SLOT |
| SF | SLOW-FAST |
| PD | SPEED BRAKE |
| PE | SPOT |
| PF | SQ |
| LF | STANDBY |
| PG | STEAM |
| PH | STORE |
| PJ | STOW |
| PK | SWIVEL |
| TA | T |
| PS | THROTTLE |
| PW | TILT |
| HH | TIME |
| TR | TO INCREASE RESISTANCE |
| HJ | TRIANGLE |
| PZ | TUNING |
| MN | TURN |
| QA | TURN TO SET |
| BL | TURN W/ARROWS POINTING RIGHT AND LEFT |
| QB | TWO DOTS |
| BZ | TWO LINES |
| QC | UHF |
| EP | UP |
| EY | V |
| QD | V GROOVE |
| JT | VAR |
| QF | VHF |
| QG | VIDEO |
| EA | VOLUME |
| QH | W |
| QK | WATER SUPPLY |
| WD | WHITE DOT |
| WL | WHITE LINE |
| QM | WINDSHIELD WIPER |
| JW | X |
| TT | Z |
IF STYLE/REPLY CODE(s) G1 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (AATR and AAZE)
IF STYLE/REPLY CODE(s) G2 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (AAZE and CSYT)
IF STYLE/REPLY CODE(s) G3 OR G4 WERE ENTERED FOR MRC AAZF, YOU MUST ANSWER MRC (AATR and AAZE and ABSN)
AAZF*LSHANK STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAZFLG3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BK10173 | G1 | STRAIGHT |
| BK10174 | G2 | TAPERED |
| BK10175 | G3 | CONCAVE |
| BK10176 | G4 | CONVEX |
AATR*JSHANK LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHANK,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATRJAB2.0*;AATRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZE*JSHANK DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY OF THE SHANK AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZEJAC2.0*;AAZEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSN*JSHANK RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSNJAA2.0*;ABSNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSYT*JCHAMFER ANGLE
THE INCLUDED ANGLE OF THE CHAMFER(S).
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYTJDA2.0*;CSYTJDA2.0$$JDA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJQE*DMATERIAL TRANSPARENCY
THE ABILITY OF THE MATERIAL TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION.
Enter the applicable reply code from the table below
(AJQEDAE)
| Table 1 |
| Reply Code (AF93) | Reply |
| AB | CLEAR |
| AE | OPAQUE |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDRE0000*;HUESDBU0000$DGY0003*;HUESDBU0000$$DGY0003*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BL0039 | BLACK, LUSTERLESS |
| BU0000 | BLUE |
| CL0000 | CLEAR |
| GY0049 | GRAY, DARK GULL |
| GY0029 | GRAY, FED STD 595, 36231 |
| GY0002 | GRAY, LIGHT |
| GY0003 | GRAY, SLATE |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| NA0000 | NATURAL |
| LD0000 | OLIVE DRAB |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
IF YOU ANSWER MRC HDCL, YOU MUST ANSWER MRC (HUES)
HDCL*JCOLOR DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(HDCLJEATEXT1234*;HDCLJEATEXT1234$$JEATEXT1234*;HDCLJEATEXT1234$JEATEXT1234*;HDCL1BJEATEXT1234*;HDCL1BJEATEXT1234$$JEATEXT1234*;HDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP93) | Reply |
| M | 10TH COLOR RESPONSE |
| N | 11TH COLOR RESPONSE |
| P | 12TH COLOR RESPONSE |
| Q | 13TH COLOR RESPONSE |
| R | 14TH COLOR RESPONSE |
| S | 15TH COLOR RESPONSE |
| T | 16TH COLOR RESPONSE |
| U | 17TH COLOR RESPONSE |
| W | 18TH COLOR RESPONSE |
| X | 19TH COLOR RESPONSE |
| B | 1ST COLOR RESPONSE |
| Y | 20TH COLOR RESPONSE |
| Z | 21ST COLOR RESPONSE |
| V | 22ND COLOR RESPONSE |
| C | 2ND COLOR RESPONSE |
| D | 3RD COLOR RESPONSE |
| E | 4TH COLOR RESPONSE |
| F | 5TH COLOR RESPONSE |
| H | 6TH COLOR RESPONSE |
| J | 7TH COLOR RESPONSE |
| K | 8TH COLOR RESPONSE |
| L | 9TH COLOR RESPONSE |
| G | ALL COLOR RESPONSE |
| A | SINGLE COLOR RESPONSE |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAR1)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJLB2.0*;AASAJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCPG*;CBBLDFNY$DCPG*)
| Table 1 |
| Reply Code (AN47) | Reply |
| CPG | KNURLED KNOB |
| FNY | ROHS DIRECTIVE COMPLIANCE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPRF000*;SFTTDENA000$DCMA000*;SFTTDENA000$$DCMA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| XXG000 | BLACK OXIDE |
| CDA000 | CADMIUM |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| CMA000 | CHROMATE |
| ENA000 | ENAMEL |
| NLA000 | NICKEL |
| AAA000 | PAINTED |
| PSA000 | PASSIVATE |
| AAA004 | POWDER COATED |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| AAAAAB | ZINC NICKEL |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAG8)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ029*;HZRDDHAZ011$$DHAZ008*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ029 | LEAD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
Enter the word CAGE immediately followed by a colon, followed by a space then the 5 position Commercial and Government Entity (CAGE) Code, followed by a space and the letters PN immediately followed by a colon, a space and the part/model/reference number.
AVMF*AADDITIVE MANUFACTURING CAGE AND PART/MODEL NUMBER
THE ADDITIVE MANUFACTURER'S FIVE-DIGIT CAGE DESIGNATION AND THE PART/MODEL NUMBER.
CAGE: XXXXX PN: XXXXXXXXX
CAGE: XXXXX PN: XXXXXXXXX AND CAGE: XXXXX PN: XXXXXXXXX
(AVMFACAGE: 30003 PN: 4866113-485-AM*;AVMFACAGE: 30003 PN: 4866113-485-AM$$CAGE: 30003 PN: 5977224-120-AM)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDQD*;ENACDQH$$DAK*)
| Table 1 |
| Reply Code (EN02) | Reply |
| QD | HEXAVALENT CHROMIUM ALTERNATIVE |
| AK | NON-CADMIUM PRODUCT |
| QH | NON-LEAD ALTERNATIVE PRODUCTS |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJE3CINJAM32.0/P50.0*;AAJE3CINJAM32.0/P50.0$$JA*;AAJE3CINJAM32.0/P50.0$JAM32.0/P50.0*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3CIN | SCREW HOLE |
| 3CIQ | SETSCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)