A rigid piece of abrasive with or without mounting facilities. Items having such mounting facilities as a fixed spindle, a threaded insert, or an arbor hole are designed for mounting on a grinding machine, tool chuck or mandrel. Items without mounting facilities are designed to be secured in a wheel holder by means of spring clamps.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED02613*)
ATPRBMAXIMUM SPEED RATING IN RPM
THE MAXIMUM SPEED AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ATPRB2.0)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AAUB and BCDX and AHDA and AHDC and AHDD)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AAUB and BCDX and AHDC and AHDA and AHDB and AHDE)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDF and AAUB and AHDA)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABMH and AAUB and BCDX and ABMD and AHDA)
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDE and AHDC and AHDB and BCDX and AHDA and AAUB and ABGG)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDF and AAUB and BCDX and AHDC and AHDA and AHDB)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AHDA and AAUB and BCDX and AHDC and AHDD)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDF and BCDX)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDB and AAUB and AHDE)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDA and AAUB and BCDX and ABMD and ABMH)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AAUB and BCDX and AHDC and AHDA and ABMD and AHDD and ABMH)
IF STYLE/REPLY CODE(s) 13, 14 OR 16 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AHDD and AHDA and BCDX and ABMD and ABMH and AAUB)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABXQ and AHDA and BCDX and ABMD and ABMH and AHDD and AAUB and AHDC)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ABMD and AHDC and AAUB and BCDX and AHDA and AHDE)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AAUB and BCDX and AHDA)
IF STYLE/REPLY CODE(s) 34 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDE and AAUB and BCDX and AHDA)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDF and AHDA and AAUB)
IF STYLE/REPLY CODE(s) 36, 37, 39, 42, 43, 47 OR 51 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB)
IF STYLE/REPLY CODE(s) 38 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB)
IF STYLE/REPLY CODE(s) 40 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDE and BCDX and AAUB)
IF STYLE/REPLY CODE(s) 41 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDE and BCDX and AAUB)
IF STYLE/REPLY CODE(s) 44 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB and AHDF)
IF STYLE/REPLY CODE(s) 45 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDE and AAUB and BCDX)
IF STYLE/REPLY CODE(s) 46 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and ABMD and ABMH and AAUB and AHDB and AHDE)
IF STYLE/REPLY CODE(s) 48 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDF and AAUB)
IF STYLE/REPLY CODE(s) 49, 50 OR 55 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB and AHDE)
IF STYLE/REPLY CODE(s) 52 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDB and AAUB and AHDE)
IF STYLE/REPLY CODE(s) 53 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB)
IF STYLE/REPLY CODE(s) 54 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB and AHDA)
IF STYLE/REPLY CODE(s) 56 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AAUB and BCDX and AHDB and ABGG)
IF STYLE/REPLY CODE(s) 57 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AAUB and BCDX)
IF STYLE/REPLY CODE(s) 58 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AAUB and BCDX)
IF STYLE/REPLY CODE(s) 59 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB and AHDE and ABMD)
IF STYLE/REPLY CODE(s) 60 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AAUB and ABGG)
IF STYLE/REPLY CODE(s) 82, 84, 86 OR 87 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and ABGG)
IF STYLE/REPLY CODE(s) 83 OR 85 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDB)
IF STYLE/REPLY CODE(s) 81, 108, 109, 110, 113, 114, 116, 118, 119, 121, 122, 127, 128, 130, 132, 139, 141, 143, 146, 151, 153, 155, 167, 168, 175 OR 185 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX)
IF STYLE/REPLY CODE(s) 123 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX)
IF STYLE/REPLY CODE(s) 210 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and ADYT and AHDG)
IF STYLE/REPLY CODE(s) 211 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (BCDX and AHDH and AHDG)
IF STYLE/REPLY CODE(s) 212 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (ADYT and AHDG and AHDF and BCDX)
IF STYLE/REPLY CODE(s) 213 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDH and AHDF and BCDX and ADYT and AHDG)
IF STYLE/REPLY CODE(s) 214 WERE ENTERED FOR MRC CZHQ, YOU MUST ANSWER MRC (AHDF and BCDX and AHDH and ADYT and AHDG)
CZHQLWHEEL STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WHEEL.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CZHQL48)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BR10001 | 1 | SAUCER |
| BR10010 | 10 | TAPERED TWO SIDES |
| BR10053 | 108 | PLUG, CONICAL END W/SQUARE TIP |
| DQ00301 | 109 | CONICAL W/FLAT TIP |
| BR10011 | 11 | RECESSED ONE SIDE |
| DQ00302 | 110 | CONICAL W/ROUND TIP |
| BR10056 | 113 | PLUG, CONICAL END, TAPERED BASE W/ ROUND TIP |
| BR10057 | 114 | CONE, CURVED SIDES W/ FLAT BASE |
| BR10059 | 116 | PLUG W/ POINTED TIP |
| BR10061 | 118 | NEEDLE |
| BR10062 | 119 | PLUG W/ROUND TIP |
| BR10012 | 12 | RELIEVED ONE SIDE/RECESSED OTHER SIDE |
| BR10064 | 121 | ROUND END, V-TAPER W/FLAT BASE |
| BR10065 | 122 | STRAIGHT W/ROUND TIP |
| BR10066 | 123 | SPHERICAL |
| BR10068 | 125 | V-TAPER, FLAT BASE W/V-TAPER END RELIEF |
| BR10070 | 127 | V-TAPER |
| BR10071 | 128 | TRUNCATED CONE |
| BR10013 | 13 | RELIEVED AND RECESSED SAME SIDE |
| BR10073 | 130 | DOUBLE SAUCER W/POINT |
| BR10075 | 132 | CYLINDRICAL W/ROUND END RELIEF |
| DQ00304 | 139 | LONG ELIPSE |
| BR10014 | 14 | RELIEVED AND RECESSED ONE SIDE/RECESSED THE OTHER SIDE |
| BR10081 | 141 | CONE,ROUND TIP W/TAPERED BASE |
| BR10083 | 143 | TEARDROP |
| BR10086 | 146 | ROUNDED WHEEL W/HUB |
| BR10015 | 15 | RELIEVED AND RECESSED ONE SIDE/RELIEVED THE OTHER SIDE |
| BR10091 | 151 | INVERTED SAUCER |
| BR10093 | 153 | ELIPTICAL SAUCER |
| BR10095 | 155 | V-TAPER W/CONCAVE AND RELIEF |
| BR10016 | 16 | RELIEVED AND RECESSED BOTH SIDES |
| BR10107 | 167 | V-TAPER, V-END RELIEF W/FLAT BASE |
| BR10108 | 168 | V-TAPER, CONCAVE END RELIEF W/FLAT BASE |
| BR10017 | 17 | DEPRESSED CENTER |
| BR10115 | 175 | V-TAPER, FLAT BOTTOM W/CONVEX TOP |
| BR10125 | 185 | CYLINDRICAL |
| BR10129 | 189 | WHEEL W/ HUB |
| BR10002 | 2 | RELIEVED TWO SIDES |
| BR10130 | 210 | NUT INSERTED |
| BR10131 | 211 | STUD INSERTED, PLAIN |
| BR10132 | 212 | PLATE MOUNTED |
| BR10133 | 213 | STUD INSERTED PLATE MOUNTED |
| BR10134 | 214 | CYLINDER TYPE WIRE WOUND |
| BR10003 | 3 | DISH |
| BR10018 | 33 | SPECIAL "A" |
| BR10019 | 34 | SPECIAL "B" |
| BR10020 | 35 | SPECIAL "C" |
| BR10021 | 36 | SPECIAL "CD" |
| BR10022 | 37 | SPECIAL "CW" |
| BR10023 | 38 | SPECIAL "DB" |
| BR10024 | 39 | SPECIAL "E" |
| BR10004 | 4 | STRAIGHT CUP |
| BR10025 | 40 | SPECIAL "F" |
| BR10026 | 41 | SPECIAL "GG" |
| BR10027 | 42 | SPECIAL "I" |
| BR10028 | 43 | SPECIAL "K" |
| BR10029 | 44 | SPECIAL "L" |
| BR10030 | 45 | SPECIAL "M" |
| BR10031 | 46 | SPECIAL "OM:" |
| BR10032 | 47 | SPECIAL "PT" |
| BR10033 | 48 | SPECIAL "Q" |
| BR10034 | 49 | SPECIAL "RD" |
| BR10005 | 5 | RECESSED TWO SIDES |
| BR10035 | 50 | SPECIAL "SW" |
| BR10036 | 51 | SPECIAL "TH" |
| BR10037 | 52 | SPECIAL "TS" |
| BR10038 | 53 | SPECIAL "W" |
| BR10039 | 54 | SPECIAL "Y" |
| BR10040 | 55 | SPECIAL "Z" |
| BR10041 | 56 | SPECIAL "ZA" |
| BR10042 | 57 | SPECIAL "ZB" |
| BR10043 | 58 | SPECIAL "ZC" |
| BR10044 | 59 | SPECIAL "ZD" |
| BR10006 | 6 | FLARING CUP |
| BR10045 | 60 | SPECIAL "ZE" |
| BR10007 | 7 | RELIEVED ONE SIDE |
| BR10008 | 8 | STRAIGHT |
| BR10046 | 81 | PLUG, SQUARE END |
| BR10047 | 82 | PLUG, ROUND END |
| BR10048 | 83 | PLUG, CONICAL END, SQUARE TIP |
| BR10049 | 84 | PLUG, CONICAL END, ROUND TIP |
| BR10050 | 85 | CONE, SQUARE TIP |
| BR10051 | 86 | CONE, CURVED SIDE |
| BR10052 | 87 | CONE, ROUND TIP |
| BR10009 | 9 | CYLINDER |
ABMH*JRECESS DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RECESS,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMHJAC2.0*;ABMHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMD*JRECESS DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECESS,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMDJAB2.0*;ABMDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAC2.0*;AAUBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXQ*JFLATTED PORTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXQJAC2.0*;ABXQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADYT*JCENTER HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADYTJAB2.0*;ADYTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDA*JHOLE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDAJAA2.0*;AHDAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDB*JOUTSIDE FLAT DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDBJAA2.0*;AHDBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDC*JINSIDE FLAT DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDCJAA2.0*;AHDCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDD*JRELIEF DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDDJAC2.0*;AHDDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDE*JEDGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN EDGE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDEJAA2.0*;AHDEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDF*JGRINDING FACE WALL THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDFJAB2.0*;AHDFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDG*JUSABLE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDGJAC2.0*;AHDGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDH*JSTUD PROTRUSION LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE STUD THAT EXTENDS ABOVE THE BASE OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDHJAA2.0*;AHDHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BCDX*JWHEEL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BCDXJAC2.0*;BCDXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJLA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
AJMS*AABRASIVE STANDARD MICRON SIZE DESIGNATOR
A DESIGNATION OF THOSE ABRASIVE SIZES USUALLY PREPARED BY METHODS OF SEPARATION OTHER THAN BY SIEVING AND USUALLY SMALLER THAN SIEVE SIZES.
Enter the numeric reply with a minimum of one digit.
(AJMSA10*)
IF STYLE/REPLY CODE(s) 1, 9 OR 10 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (ABMZ)
IF STYLE/REPLY CODE(s) 2, 4, 7 OR 8 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (ASDB)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (BFRH and ABGL)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (ABMZ and AHEG and ABTH)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (ABMZ and BFRH and ABGL and ABGG)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (ABGG and BFRH and ASDB)
ADQK*LMOUNTING OPENING SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MOUNTING OPENING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ADQKL3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BR10159 | 1 | ROUND |
| BR10168 | 10 | ROUND WITH TWO SLOTS |
| BR10169 | 11 | SPECIAL DIAMOND |
| BR10160 | 2 | DIAMOND |
| BR10161 | 3 | RECTANGULAR WITH ROUNDED ENDS |
| BR10162 | 4 | SQUARE WITH ROUNDED CORNERS |
| BR10163 | 5 | DOUBLE HOLE |
| BR10164 | 6 | SPECIAL RECTANGULAR |
| BR10165 | 7 | SQUARE |
| BR10166 | 8 | HEXAGON |
| BR10167 | 9 | ROUND WITH FOUR SLOTS |
ABGG*JRADIUS
THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGGJLA2.0*;ABGGJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAB2.0*;ABGLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAB2.0*;ABMZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTH*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES
THE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTHJAA2.0*;ABTHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHEG*JPILOT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PILOT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHEGJAB2.0*;AHEGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFRH*JOPENING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE OPENING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFRHJAC2.0*;BFRHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
THDS*JTHREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(THDSJNSTEXT1234*)
| Table 1 |
| Reply Code (AH06) | Reply |
| BF | BSF |
| SM | ISO M |
| SS | ISO S |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5 OR 10 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (AHDJ)
IF STYLE/REPLY CODE(s) 7, 8, 9, 12 OR 15 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (AHDJ and AHDK)
ADER*LMOUNTING STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ADERL15)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BR10170 | 1 | ONE DIAMETER |
| BR10179 | 10 | ONE DIAMETER |
| BR10181 | 12 | TWO DIAMETERS |
| BR10184 | 15 | TWO DIAMETERS |
| BR10171 | 2 | ONE DIAMETER |
| BR10172 | 3 | ONE DIAMETER |
| BR10173 | 4 | ONE DIAMETER |
| BR10174 | 5 | ONE DIAMETER |
| BR10176 | 7 | TWO DIAMETERS |
| BR10177 | 8 | TWO DIAMETERS |
| BR10178 | 9 | TWO DIAMETERS |
AHDJ*JFIRST BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDJJAC2.0*;AHDJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDK*JSECOND BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDKJAB2.0*;AHDKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSXS*JANGLE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSXSJD2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| D | DEGREES |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAC2.0*;ADUMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDBTY*;ALBYDBTW$$DBTX*)
| Table 1 |
| Reply Code (AH21) | Reply |
| BTW | AGGREGATE, HARD WORKING |
| BUB | BRICK WORKING |
| BUC | CINDER BLOCK WORKING |
| BTX | CONCRETE WORKING |
| BTZ | CUTOFF |
| AAG | DENTAL |
| BTV | GLASS WORKING |
| BUA | GRINDING WOOD |
| BTT | MASONRY WORKING |
| AAJ | METALWORKING |
| BTU | STONE POLISHING |
| BUD | VALVE SEAT GRINDING |
| BTY | VEGETABLE PEELING |
| AAK | WOODWORKING |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDBUS)
| Table 1 |
| Reply Code (AM39) | Reply |
| BUN | ARBOR HOLE |
| BUQ | NUT INSERT |
| BUP | PERMANENTLY MOUNTED ON MANDREL |
| BUR | PLATE WITH COUNTERSUNK MOUNTING HOLES |
| BUT | PLATE WITH MOUNTING HOLES |
| BZG | SPINDLE |
| BUS | STUD INSERT |
| ACH | THREADED INSERT |
AHCS*AABRASIVE GRAIN STRUCTURE DESIGNATOR
THE NUMBER OR SYMBOL DESIGNATING THE STRUCTURE OR GRAIN SPACING WHICH IS DETERMINED BY THE PROPORTION AND ARRANGEMENT OF THE ABRASIVE AND BOND.
Enter the alpha-numeric reply with a minimum of one character.
(AHCSAE1)
AJMV*AAVERAGE PARTICLE SIZE DESIGNATOR
A DESIGNATION INDICATING THE AVERAGE SIZE OF THE PARTICLES.
Enter the alpha-numeric reply with a minimum of one character.
(AJMVAM4)
AJGJ*ASEDIMENTATION GRIT SIZE DESIGNATOR
A DESIGNATION INDICATING THE RATED SIZE OF THE INDIVIDUAL SEDIMENTATION GRIT PARTICLES.
Enter the alpha-numeric reply with a minimum of one character.
(AJGJAE4)
AHCN*ASCREEN GRIT SIZE DESIGNATOR
A DESIGNATION INDICATING THE RATED SIZE OF THE INDIVIDUAL PARTICLES,SOMETIMES EXPRESSED AS A MESH SIZE.
Enter the numeric reply with a minimum of one digit.
(AHCNA10*)
AHDP*JBOLT CIRCLE HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDPJAB2.0*;AHDPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATA*BCOUNTERSINK ANGLE IN DEG
THE INCLUDED ANGLE OF THE COUNTERSINK,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AATAB2.0)
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWYJAA2.0*;AAWYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZJAA2.0*;AAWZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADBG*JNUT THICKNESS
A MEASUREMENT BETWEEN THE OPPOSITE FLAT SURFACES OF THE NUT,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADBGJAB2.0*;ADBGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDL)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
AHDQ*JSPINDLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPINDLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDQJAA2.0*;AHDQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDR*JSPINDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A SPINDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDRJAB2.0*;AHDRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDS*JSPINDLE THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS OF THE SPINDLE ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHDSJAA2.0*;AHDSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHDY*DABRASIVE BOND GRADE DESIGNATION
A DESIGNATION INDICATING THE RELATIVE STRENGTH /HOLDING POWER/ OF THE BOND WHICH HOLDS THE ABRASIVE GRAINS IN PLACE.
Enter the applicable reply code from the table below
(AHDYDAE)
| Table 1 |
| Reply Code (AF20) | Reply |
| AB | A SOFT |
| AC | B SOFT |
| AD | C SOFT |
| AE | D SOFT |
| AF | E SOFT |
| AG | F SOFT |
| AH | G SOFT |
| AJ | H SOFT |
| AK | I MEDIUM |
| AL | J MEDIUM |
| AM | K MEDIUM |
| AN | L MEDIUM |
| AP | M MEDIUM |
| AQ | N MEDIUM |
| AR | O MEDIUM |
| AS | P MEDIUM |
| AT | Q HARD |
| AU | R HARD |
| AV | S HARD |
| AW | T HARD |
| AX | U HARD |
| AY | V HARD |
| AZ | W HARD |
| BA | X HARD |
| BB | Y HARD |
| BC | Z HARD |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDAM0000*;HUESDYE0000$DCL0000*;HUESDYE0000$$DCL0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AM0000 | AMBER |
| BL0000 | BLACK |
| BU0000 | BLUE |
| BR0000 | BROWN |
| CL0000 | CLEAR |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| LD0000 | OLIVE DRAB |
| RG0000 | ORANGE |
| RE0000 | RED |
| RU0000 | RUSSET |
| TA0000 | TAN |
| VL0000 | VIOLET |
| WA0000 | WALNUT |
| WH0000 | WHITE |
| YE0000 | YELLOW |
IF YOU ANSWER MRC HDCL, YOU MUST ANSWER MRC (HUES)
HDCL*JCOLOR DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(HDCLJEATEXT1234*;HDCLJEATEXT1234$$JEATEXT1234*;HDCLJEATEXT1234$JEATEXT1234*;HDCL1BJEATEXT1234*;HDCL1BJEATEXT1234$$JEATEXT1234*;HDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP93) | Reply |
| M | 10TH COLOR RESPONSE |
| N | 11TH COLOR RESPONSE |
| P | 12TH COLOR RESPONSE |
| Q | 13TH COLOR RESPONSE |
| R | 14TH COLOR RESPONSE |
| S | 15TH COLOR RESPONSE |
| T | 16TH COLOR RESPONSE |
| U | 17TH COLOR RESPONSE |
| W | 18TH COLOR RESPONSE |
| X | 19TH COLOR RESPONSE |
| B | 1ST COLOR RESPONSE |
| Y | 20TH COLOR RESPONSE |
| Z | 21ST COLOR RESPONSE |
| V | 22ND COLOR RESPONSE |
| C | 2ND COLOR RESPONSE |
| D | 3RD COLOR RESPONSE |
| E | 4TH COLOR RESPONSE |
| F | 5TH COLOR RESPONSE |
| H | 6TH COLOR RESPONSE |
| J | 7TH COLOR RESPONSE |
| K | 8TH COLOR RESPONSE |
| L | 9TH COLOR RESPONSE |
| G | ALL COLOR RESPONSE |
| A | SINGLE COLOR RESPONSE |
AAUG*JSHANK LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A SHANK,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUGJAB2.0*;AAUGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDNR*;ENACDNZ$$DNZ*)
| Table 1 |
| Reply Code (EN02) | Reply |
| NZ | PLASTICS REMOVAL IN THE MARINE ENVIRONMENT (PRIME) PRODUCT |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ANTN*GSPECIFIC USE
THE REQUIRED PURPOSE OR APPLICATION FOR WHICH THE ITEM IS DESIGNED.
Enter clear text.
(ANTNGCLEARTEXT)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information