An electrically driven hammer designed for the impact driving of items such as inserted chisels, masonry drills and like items. It may include working tools, ejector pins, and the like. In operation the tool is not fixed and is controlled by hand.

FSC Information

5130	Hand Tools, Power Driven

Colloquial Information

H2805	CHIPPING HAMMER,ELECTRIC
H5390	HAMMER,SCALING,ELECTRIC
J6305	CAULKING HAMMER,ELECTRIC
H9135	SCALING HAMMER,ELECTRIC

Change List

NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.

Enter the item name code.

AMSEJVOLTAGE RATING

THE VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AMSEJKC2.0*;AMSEJKC2.0$$JKC2.1*)

Table 1
	Reply Code (AB63)	Reply
	K	KILOVOLTS
	V	VOLTS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BRZZDPLUG CONNECTOR TYPE

INDICATES THE TYPE OF PLUG CONNECTOR PROVIDED.

Enter the applicable reply code from the table below

(BRZZDAM*;BRZZDAL$DAQ*)

Table 1
	Reply Code (AK12)	Reply
	AL	2-PRONG
	AM	3-PRONG
	AQ	4-PRONG

ABHPJOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BSJTDELECTRIC POWER OPERATION METHOD

THE MEANS BY WHICH ELECTRICITY IS USED TO POWER THE OPERATING MECHANISM OF THE ITEM.

Enter the applicable reply code from the table below

Table 1
	Reply Code (AC58)	Reply
	CE	MAGNETIC
	HD	MOTOR

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (FAAZ and ACZB and ACUS)

IF STYLE/REPLY CODE(s) C WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (ACUT)

ACDCDCURRENT TYPE

INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.

Enter the applicable reply code from the table below

(ACDCDB*;ACDCDC$DB*)

Table 1
	Reply Code (AB62)	Reply
	B	AC
	C	DC

ACZBJFREQUENCY RATING

THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ACZBJKB2.0*;ACZBJKB2.0$$JKB2.1*)

Table 1
	Reply Code (AC32)	Reply
	E	HERTZ
	K	KILOHERTZ

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

THE NUMBER OF ALTERNATING CURRENT PHASES.

Enter the applicable reply code from the table below

(FAAZDA*;FAAZDB$DC*)

Table 1
	Reply Code (AD02)	Reply
	A	SINGLE
	C	THREE
	B	TWO

ACUS*BALTERNATING CURRENT RATING IN AMPS

THE ALTERNATING CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES.

Enter a reply with a minimum of one digit on either side of the decimal point.

ACUT*BDIRECT CURRENT RATING IN AMPS

THE DIRECT CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(ACUTB2.0*;ACUTB2.0$$BM2.0*)

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	C	MAXIMUM

AKUL*BIMPACT BLOWS PER MINUTE

THE NUMBER OF IMPACT BLOWS WHICH THE ITEM WILL MAKE WITHIN A SPECIFIC PERIOD OF TIME.

Enter a reply with a minimum of one digit on either side of the decimal point.

IF STYLE/REPLY CODE(s) AB1 OR AB12 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and BGML and BWLP and BGMJ and ATCG)

IF STYLE/REPLY CODE(s) AB2 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (AAZW and ATCH and AAZX and ALEB and ATCG and BGMH and BWLP and BGMJ and BGML)

IF STYLE/REPLY CODE(s) AB3 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and BWLP and BGMJ and ATCG)

IF STYLE/REPLY CODE(s) AB4 OR AB17 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BWLP and ATCG)

IF STYLE/REPLY CODE(s) AB5 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and AAZW and BGMP and AAZX and ALEB and ATCG and BGML and BGMJ and BWLP)

IF STYLE/REPLY CODE(s) AB6 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and ATCH and BGML and ATCG and ALEB and BGMK and ABMZ)

IF STYLE/REPLY CODE(s) AB7, AB11 OR AB19 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB8 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and BGML and ATCG and BGMK and ABMZ)

IF STYLE/REPLY CODE(s) AB9 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMH and BGML and ABPA and BGMK and ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB10 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMR and ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB13 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (ABPA and ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB14 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB15 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (ABGG and ATCG and ABMZ)

IF STYLE/REPLY CODE(s) AB16 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BWLP and ABGD and ATCG)

IF STYLE/REPLY CODE(s) AB18 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (AAZW and ATCH and BGMH and ATCG and AAZX and ALEB and BGML and BGMK and ABMZ)

IF STYLE/REPLY CODE(s) AB20 WERE ENTERED FOR MRC BSJM, YOU MUST ANSWER MRC (BGMM and BGMS and BGMN and ATCG and ABMZ)

BSJM*LACCOMMODATED TOOL SHANK STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK THAT THE TOOL WILL ACCOMMODATE.

Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AH10776	AB1	HEXAGON
AH10784	AB10	STRAIGHT
AH10785	AB11	STRAIGHT
AH10786	AB12	QUARTER
AH10787	AB13	CYLINDRICAL
AH10790	AB14	TAPER
AH10791	AB15	PARKER TAPER
AH10792	AB16	SQUARE
AH10793	AB17	SOLID SQUARE
AH10794	AB18	DIFFERENTIAL
AH10788	AB19	STRAIGHT
AH10777	AB2	HEXAGON
AH10789	AB20	STRAIGHT
AH10778	AB3	COMBINATION
AH10807	AB4	STRAIGHT
AH10779	AB5	HEXAGON
AH10780	AB6	ROUND
AH10781	AB7	ROUND
AH10782	AB8	DIFFERENTIAL
AH10783	AB9	COMPOUND

AAZW*JSECOND SHOULDER DIAMETER

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAZWJAC2.0*;AAZWJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AAZX*JSECOND SHOULDER LENGTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAZXJAC2.0*;AAZXJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABGD*JSLOT LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABGDJAA2.0*;ABGDJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABGGJAC2.0*;ABGGJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABPA*JUNDERCUT DIAMETER

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABPAJAC2.0*;ABPAJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ALEB*JRETAINER WIDTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ALEBJAB2.0*;ALEBJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATCG*JSHANK OVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHANK.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ATCGJAC2.0*;ATCGJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ATCH*JRETAINER DIAMETER

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ATCHJAA2.0*;ATCHJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMH*JFIRST SHOULDER DIAMETER

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMHJAB2.0*;BGMHJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMJ*JFLAT LENGTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMJJAA2.0*;BGMJJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMK*JROUND TANG LENGTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMKJAB2.0*;BGMKJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGML*JFIRST SHOULDER LENGTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMLJAA2.0*;BGMLJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMM*JRETAINER GROOVE WIDTH

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMMJAA2.0*;BGMMJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMN*JRETAINER GROOVE DIAMETER

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMNJAC2.0*;BGMNJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMP*JWIDTH ACROSS RETAINER FLATS

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMPJAA2.0*;BGMPJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMR*JDISTANCE BETWEEN RETAINER GROOVE CENTER AND FLANGE

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMRJAC2.0*;BGMRJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BGMS*JDISTANCE BETWEEN SHANK END AND RETAINER GROOVE

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BGMSJAC2.0*;BGMSJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BWLP*JSHANK WIDTH ACROSS FLATS

THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF THE SHANK.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BWLPJAC2.0*;BWLPJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BSJW*JMASONRY DRILL SIZE

DESIGNATES THE MASONRY DRILL SIZE OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BSJWJAA2.0*;BSJWJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDDPD*;CBBLDFDJ$$DAGJ*)

Table 1
	Reply Code (AN47)	Reply
	FLV	AUXILIARY SIDE HANDLE
	DPD	CARRYING CASE
	FCF	DOUBLE INSULATED
	FDJ	ELECTROMAGNETIC INTERFERENCE SUPPRESSION
	AGJ	FUNGUS RESISTANT TREATMENT

AKYD*GACCESSORY COMPONENTS AND QUANTITY

THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.

Enter clear text.

(AKYDGCLEARTEXT)

AQFK*GLOUDNESS LEVEL IN DECIBELS

THE LEVEL OF A SIGNAL OR SOUND RELATIVE TO A SPECIFIC DISTANCE,EXPRESSED IN DECIBELS.

Enter clear text.

(AQFKGCLEARTEXT)

ALVS*BVIBRATION LEVEL IN METERS PER SECOND SQUARED

A NUMERIC VALUE INDICATING THE VIBRATION OUTPUT OF THE ITEM EXPRESSED IN METERS PER SECOND SQUARED.

Enter a reply with a minimum of one digit on either side of the decimal point.

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

FTLD*GFUNCTIONAL DESCRIPTION

DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.

Enter the reply from the applicable document.

(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)