A switch with a quick-acting mechanism actuated by a highly delicate tactile contact. It may include a timer function. Includes membrane switch. Excludes: SWITCH,FLEXIBLE; SWITCH,PRESSURE; and SWITCH,THERMOSTATIC.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00399*)
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3CEPDPCA000*;MATT3CEPDPCA000$DPCBC00*;MATT3CEPDPCA000$$DPCBC00*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3CEP | CASE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL7075 | ALUMINUM ALLOY 7075 |
| BND000 | BRONZE |
| BNAAAA | BRONZE CAST |
| CLD000 | CERAMIC |
| CRA000 | CHROMIUM |
| CRB000 | CHROMIUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| FBA000 | FIBER |
| FG0000 | FIBERGLASS |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| RBR000 | HARD RUBBER |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| LRA000 | LEATHER |
| LRE000 | LEATHER ARTIFICIAL |
| MGB000 | MAGNESIUM ALLOY |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCJ000 | PLASTIC MELAMINE |
| PCCB00 | PLASTIC NYLON |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAK00 | PLASTIC SILICONE |
| PCBC00 | PLASTIC STYRENE |
| CLB000 | PORCELAIN |
| STA000 | STEEL |
| ST0302 | STEEL COMP 302 |
| ST0304 | STEEL COMP 304 |
| ST0316 | STEEL COMP 316 |
| STB000 | STEEL CORROSION RESISTING |
| AAA012 | THERMOPLASTIC |
| WDC000 | WOOD |
| WDL000 | WOOD MAHOGANY |
| WDR000 | WOOD OAK |
| WDE000 | WOOD WALNUT |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
AFXEJMAXIMUM VOLTAGE RATING IN VOLTS
THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE IN AN ALTERNATING CURRENT AND/OR DIRECT CURRENT CIRCUIT,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFXEJC2.0*;AFXEJC2.0$JC2.0*;AFXEJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AE16) | Reply |
| B | AC |
| C | DC |
CXQRJCONTACT LOAD CURRENT RATING AT MAXIMUM RATED VOLTAGE
THE AMOUNT OF CURRENT THE CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED VOLTAGE,WITH A SPECIFIED LOAD.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQRJAALC2.0*;CXQRJAALC2.0$$JAALC2.1*)
| Table 1 |
| Reply Code (AC30) | Reply |
| A | AMPERES |
| L | MILLIAMPERES |
| Table 2 |
| Reply Code (AK53) | Reply |
| AD | INDUCTIVE |
| AL | LAMP |
| AM | MOTOR |
| AC | RESISTIVE |
| Table 3 |
| Reply Code (AE16) | Reply |
| B | AC |
| A | AMP |
| C | DC |
IF STYLE/REPLY CODE(s) 1M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ)
IF STYLE/REPLY CODE(s) 2M OR 3M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABXD and ADAQ and ABPM)
IF STYLE/REPLY CODE(s) 4M OR 5M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and ADAU and ABXD and ADAQ)
IF STYLE/REPLY CODE(s) 6M OR 7M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ)
IF STYLE/REPLY CODE(s) 8M, 9M, 20M, 22M OR 23M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAU and ADAT and ABKQ)
IF STYLE/REPLY CODE(s) 10M, 11M, 12M, 13M, 21M OR 24M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and AEBW and ABKQ)
IF STYLE/REPLY CODE(s) 14M, 15M, 18M OR 19M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAU and ADAT and ABXD and ABKQ)
IF STYLE/REPLY CODE(s) 16M OR 17M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAU and ADAT and AEBW and ABXD and ABKQ)
IF STYLE/REPLY CODE(s) 25M OR 27M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and ADAU and ADAQ and AEBW)
IF STYLE/REPLY CODE(s) 26M OR AAA WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and ADAU and ADAQ)
IF STYLE/REPLY CODE(s) 41M, 42M, 46M, 48M, 59M, 60M, 65M, 66M, 67M, 68M, 69M, 70M, 71M OR 72M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWE and AFWD and AFWC and AFWH)
IF STYLE/REPLY CODE(s) 43M, 45M OR 47M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWE and AFWC and AFWD and AFWJ)
IF STYLE/REPLY CODE(s) 44M, 53M, 54M, 55M, 56M OR 77M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWD and AFWE and AFWC and AFWG and AFWH)
IF STYLE/REPLY CODE(s) 49M, 50M, 51M, 52M, 57M, 58M, 61M, 62M, 63M OR 64M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWE and AFWD and AFWC)
IF STYLE/REPLY CODE(s) 73M, 74M, 75M, 76M, 78M, 79M OR 80M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWC and AFWD and AFWE and AFWJ and AFWH)
IF STYLE/REPLY CODE(s) 81M OR 82M WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AFWB and AFWD and AFWF)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL15M)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AN10149 | 10M | HOLE MOUNTED |
| AN10150 | 11M | HOLE MOUNTED |
| AN10151 | 12M | HOLE MOUNTED |
| AN10152 | 13M | HOLE MOUNTED |
| AN10153 | 14M | BUSHING/HOLE MOUNTED |
| AN10154 | 15M | BUSHING/HOLE MOUNTED |
| AN10155 | 16M | BUSHING/HOLE MOUNTED |
| AN10156 | 17M | BUSHING/HOLE MOUNTED |
| AN10157 | 18M | BUSHING/HOLE MOUNTED |
| AN10158 | 19M | BUSHING/HOLE MOUNTED |
| AN10140 | 1M | BUSHING MOUNTED |
| AN10159 | 20M | HOLE MOUNTED |
| AN10160 | 21M | HOLE MOUNTED |
| AN10161 | 22M | HOLE MOUNTED |
| AN10162 | 23M | HOLE MOUNTED |
| AN10163 | 24M | HOLE MOUNTED |
| AN10164 | 25M | HOLE MOUNTED |
| AN10165 | 26M | HOLE MOUNTED |
| AN10166 | 27M | HOLE MOUNTED |
| AN10141 | 2M | BUSHING MOUNTED |
| AN10142 | 3M | BUSHING MOUNTED |
| AN10167 | 41M | HOLE MOUNTED |
| AN10168 | 42M | HOLE MOUNTED |
| AN10169 | 43M | HOLE MOUNTED |
| AN10170 | 44M | HOLE MOUNTED |
| AN10171 | 45M | HOLE MOUNTED |
| AN10172 | 46M | HOLE MOUNTED |
| AN10173 | 47M | HOLE MOUNTED |
| AN10174 | 48M | HOLE MOUNTED |
| AN10175 | 49M | RH ACCESS COVER |
| AN10143 | 4M | BUSHING MOUNTED |
| AN10176 | 50M | LH ACCESS COVER |
| AN10177 | 51M | RH ACCESS COVER |
| AN10178 | 52M | LH ACCESS COVER |
| AN10179 | 53M | HOLE MOUNTED |
| AN10180 | 54M | HOLE MOUNTED |
| AN10181 | 55M | HOLE MOUNTED |
| AN10182 | 56M | HOLE MOUNTED |
| AN10183 | 57M | RH ACCESS COVER |
| AN10184 | 58M | LH ACCESS COVER |
| AN10185 | 59M | RH ACCESS COVER |
| AN10144 | 5M | BUSHING MOUNTED |
| AN10186 | 60M | LH ACCESS COVER |
| AN10187 | 61M | RH ACCESS COVER |
| AN10189 | 62M | LH ACCESS COVER |
| AN10190 | 63M | RH ACCESS COVER |
| AN10191 | 64M | LH ACCESS COVER |
| AN10192 | 65M | RH ACCESS COVER |
| AN10193 | 66M | LH ACCESS COVER |
| AN10194 | 67M | RH ACCESS COVER |
| AN10195 | 68M | LH ACCESS COVER |
| AN10196 | 69M | RH ACCESS COVER |
| AN10145 | 6M | HOLE MOUNTED |
| AN10197 | 70M | LH ACCESS COVER |
| AN10198 | 71M | RH ACCESS COVER |
| AN10199 | 72M | LH ACCESS COVER |
| AN10200 | 73M | HOLE MOUNTED |
| AN10201 | 74M | HOLE MOUNTED |
| AN10202 | 75M | HOLE MOUNTED |
| AN10203 | 76M | HOLE MOUNTED |
| AN10204 | 77M | HOLE MOUNTED |
| AN10205 | 78M | HOLE MOUNTED |
| AN10206 | 79M | HOLE MOUNTED |
| AN10146 | 7M | HOLE MOUNTED |
| AN10207 | 80M | HOLE MOUNTED |
| AN10208 | 81M | BUSHING MOUNTED |
| AN10209 | 82M | BUSHING MOUNTED |
| AN10147 | 8M | HOLE MOUNTED |
| AN10148 | 9M | HOLE MOUNTED |
| DR11442 | AAA | HOLE MOUNTED |
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5, 6, 7 OR 8 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUR and AFUS and AFUU)
IF STYLE/REPLY CODE(s) 9, 10, 22, 23, 24, 25, 26, 27, 34, 60, 65 OR 10A WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUR and AFUS)
IF STYLE/REPLY CODE(s) 11, 13, 14, 15, 16, 17, 18, 19, 20, 21, 50, 54, 55, 56, 57, 58 OR 59 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUT and AFGK and AFUS)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUT and AFGK and AFUS and AFUU)
IF STYLE/REPLY CODE(s) 28, 29, 30, 31, 32, 33 OR 35 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUT and AFUS)
IF STYLE/REPLY CODE(s) 36, 38 OR 39 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFGK and AFUS)
IF STYLE/REPLY CODE(s) 37, 62 OR 63 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFGK and AFUT)
IF STYLE/REPLY CODE(s) 40, 41, 42 OR 43 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUT and AFGK and AFUU)
IF STYLE/REPLY CODE(s) 44, 45, 46 OR 47 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUW and AFUV and AFGK and AFUU)
IF STYLE/REPLY CODE(s) 48 OR 49 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUV and AFUW and AFUU)
IF STYLE/REPLY CODE(s) 51 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUW and AFUV and AFGK and AFUS)
IF STYLE/REPLY CODE(s) 52 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUR and AFGK and AFUS)
IF STYLE/REPLY CODE(s) 53 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUT and AFUR and AFGK and AFUS)
IF STYLE/REPLY CODE(s) 61 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFGK and AFUR)
IF STYLE/REPLY CODE(s) 64 WERE ENTERED FOR MRC AFUQ, YOU MUST ANSWER MRC (AFUS)
AFUQLACTUATOR STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ACTUATOR.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AFUQL54)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AN10255 | 1 | ROUND |
| AN10264 | 10 | ROUND, FLUSH |
| AN10265 | 10A | ROUND, FLUSH |
| AN10266 | 11 | ROUND, DUAL |
| AN10267 | 12 | RECTANGULAR |
| AN10268 | 13 | RECTANGULAR |
| AN10269 | 14 | RECTANGULAR |
| AN10270 | 15 | RECTANGULAR |
| AN10271 | 16 | RECTANGULAR |
| AN10272 | 17 | RECTANGULAR |
| AN10273 | 18 | RECTANGULAR |
| AN10274 | 19 | RECTANGULAR |
| AN10256 | 2 | ROUND |
| AN10275 | 20 | RECTANGULAR |
| AN10276 | 21 | RECTANGULAR |
| AN10277 | 22 | ROUND |
| AN10278 | 23 | ROUND |
| AN10279 | 24 | ROUND |
| AN10280 | 25 | ROUND |
| AN10281 | 26 | ROUND |
| AN10282 | 27 | ROUND |
| AN10283 | 28 | RECTANGULAR |
| AN10284 | 29 | RECTANGULAR |
| AN10257 | 3 | ROUND |
| AN10285 | 30 | RECTANGULAR |
| AN10286 | 31 | RECTANGULAR |
| AN10287 | 32 | RECTANGULAR |
| AN10288 | 33 | FORKED |
| AN10289 | 34 | ROUND |
| AN10290 | 35 | RECTANGULAR |
| AN10291 | 36 | FORMED ROD |
| AN10292 | 37 | FORMED ROD |
| AN10293 | 38 | CAST/STAMPED |
| AN10294 | 39 | CAST/STAMPED |
| AN10258 | 4 | ROUND |
| AN10295 | 40 | LEAF |
| AN10296 | 41 | LEAF |
| AN10297 | 42 | LEAF |
| AN10298 | 43 | LEAF |
| AN10299 | 44 | ROLLER ARM |
| AN10300 | 45 | ROLLER ARM |
| AN10301 | 46 | ROLLER ARM |
| AN10302 | 47 | ROLLER ARM |
| AN10303 | 48 | ROLLER PLUNGER |
| AN10304 | 49 | ROLLER PLUNGER |
| AN10259 | 5 | ROUND |
| AN10305 | 50 | NONADJUSTABLE ARM |
| AN10306 | 51 | ROLLER ARM |
| AN10308 | 52 | ADJUSTABLE ARM |
| AN10307 | 53 | ADJUSTABLE ARM |
| AN10309 | 54 | PIVOTED |
| AN10310 | 55 | PIVOTED |
| AN10311 | 56 | PIVOTED |
| AN10312 | 57 | PIVOTED |
| AN10313 | 58 | NONPIVOTED |
| AN10314 | 59 | NONPIVOTED |
| AN10260 | 6 | ROUND |
| AN10315 | 60 | FLEXIBLE |
| AN10316 | 61 | CHAIN |
| AN10317 | 62 | ROUND |
| AN10318 | 63 | RECTANGULAR |
| AN10319 | 64 | ROUND, THREADED |
| AN10320 | 65 | UNDERCUT,PAN HEAD |
| AN10261 | 7 | ROUND |
| AN10262 | 8 | ROUND |
| AN10263 | 9 | ROUND, STEPPED |
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AEBV)
AXGYDMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDAGH*;AXGYDAGQ$$DAGR*)
| Table 1 |
| Reply Code (AM39) | Reply |
| ABB | BASE |
| ABC | BRACKET |
| AFL | CLIP |
| ACR | FLANGE |
| AGQ | FLUSH |
| ABL | FRICTION |
| AGR | HANGER |
| AGT | INSIDE ROD |
| AAB | INTEGRAL |
| AGH | INTERNAL THREAD |
| AHH | MALE PRONG |
| AED | PANEL |
| ADC | PRESS FIT |
| AEZ | PRINTED CIRCUIT |
| AHK | RETAINING PLATE |
| ABW | SCREW |
| AGY | SCREW CLAMP |
| AGZ | SCREW LOCK |
| AAF | SETSCREW |
| ABY | SLOT |
| AHB | SPRING CONTACT |
| AJR | STRUT |
| AAE | STUD |
| AHC | SWEATED |
| ACD | TERMINAL |
| AFA | THREADED BUSHING |
| AJZ | THREADED BUSHING W/PANEL SEAL |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| BTW | UNTHREADED BUSHING |
| ACQ | UNTHREADED HOLE |
AKNADINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAH*;AKNADAD$DAB*)
| Table 1 |
| Reply Code (AG85) | Reply |
| AH | FULLY INCLOSED |
| AD | HERMETICALLY SEALED |
| AB | UNINCLOSED |
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAF2*;TTQYJAAF2$$JAAF3*;TTQYJAAF2$JAAF2*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ABL | BINDING POST |
| AEM | BUS BAR |
| AEP | CABLE W/CONNECTOR |
| ADB | CLIP |
| AEB | COMPRESSION |
| ACN | CONNECTOR, PLUG |
| AAF | CONNECTOR, RECEPTACLE |
| AFL | CRIMP |
| AJT | ELECTRON TUBE BASE |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| ADA | QUICK DISCONNECT, FEMALE |
| ACZ | QUICK DISCONNECT, MALE |
| ABQ | SCREW |
| AEL | SOCKET, INTEGRATED WIRE TERMINATION |
| AAS | SOLDER STUD |
| AEK | SOLDERLESS LUG |
| AEN | SPRING |
| ABX | TAB W/SCREW |
| ABB | TAB, SOLDER LUG |
| ABD | THREADED STUD |
| ACB | TURRET |
| ACM | WIRE HOOK |
| ACC | WIRE LEAD |
| ACD | WIRE LOOP |
| AFM | WIRE WRAP |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQJAA2.0*;ABKQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRLD*JNONPILE-UP CONTACT ARRANGEMENT
THE DESIGNATION THAT IDENTIFIES THE ELECTRICAL CONFIGURATION OF A NONPILE-UP CONTACT GROUP INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CRLD3AMQJAB2*;CRLD3AMQJAB2$$JAB3*;CRLD3AMQJAB2$JAB2*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AMP | FIRST SWITCH UNIT |
| 3AMQ | SECOND SWITCH UNIT |
| 3AMR | THIRD SWITCH UNIT |
| 3AMZ | SINGLE SWITCH UNIT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AG28) | Reply |
| BB | FOUR THROW, DOUBLE MAKE, NORMALLY OPEN, MOMENTARY ACTION |
| BA | FOUR THROW, NORMALLY OPEN, MOMENTARY ACTION |
| BC | FOUR WAY |
| AH | POLE, DOUBLE THROW, BOTH POSITIONS MAINTAINED |
| AL | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, ONE POSITION MOMENTARY |
| AJ | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER, BOTH POSITIONS MAINTAINED |
| AM | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER, ONE POSITION MOMENTARY |
| AK | POLE, DOUBLE THROW, ONE POSITION MOMENTARY |
| AP | POLE, DOUBLE THROW, ONE POSITION MOMENTARY, TWO POSITIONS MAINTAINED |
| AR | POLE, DOUBLE THROW, PERMANENT INTERNAL JUMPERS, BOTH POSITIONS MAINTAINED |
| AN | POLE, DOUBLE THROW, THREE POSITIONS MAINTAINED |
| AQ | POLE, DOUBLE THROW, TWO POSITIONS MOMENTARY |
| AA | POLE, SINGLE THROW, BOTH POSITIONS MAINTAINED |
| AB | POLE, SINGLE THROW, DOUBLE MAKE, BOTH POSITIONS MAINTAINED |
| CB | POLE, SINGLE THROW, DOUBLE MAKE, BOTH POSITIONS MAINTAINED, WITH CONTACT ON ARM |
| AC | POLE, SINGLE THROW, DUAL CONTACT, BOTH POSITIONS MAINTAINED |
| AG | POLE, SINGLE THROW, NORMALLY CLOSED, DOUBLE BREAK, MOMENTARY ACTION |
| CG | POLE, SINGLE THROW, NORMALLY CLOSED, DOUBLE BREAK, MOMENTARY ACTION, WITH CONTACT ON ARM. |
| AF | POLE, SINGLE THROW, NORMALLY CLOSED, MOMENTARY ACTION |
| AE | POLE, SINGLE THROW, NORMALLY OPEN, DOUBLE MAKE, MOMENTARY ACTION |
| CE | POLE, SINGLE THROW, NORMALLY OPEN, DOUBLE MAKE, MOMENTARY ACTION, WITH CONTACT ON ARM |
| AD | POLE, SINGLE THROW, NORMALLY OPEN, MOMENTARY ACTION |
| AS | TWO CIRCUIT, BOTH POSITIONS MAINTAINED |
| AT | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, BOTH POSITIONS MAINTAINED |
| AW | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, ONE POSITION MOMENTARY |
| AU | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER WITH NO EXTERNAL TERMINAL, BOTH POSITIONS MAINTAINED |
| AX | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER WITH NO EXTERNAL TERMINAL, ONE POSITION MOMENTARY |
| AZ | TWO CIRCUIT, DOUBLE MAKE, TWO POSITIONS MOMENTARY |
| AV | TWO CIRCUIT, ONE POSITION MOMENTARY |
| AY | TWO CIRCUIT, TWO POSITIONS MOMENTARY |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQDK*APILE-UP CONTACT FORM ARRANGEMENT
THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,THAT COLLECTIVELY DESCRIBE THE SWITCHING STRUCTURE OF A PILE-UP CONTACT GROUP.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CQDK3ANAAK8)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ANA | FIRST POSITION |
| 3ANB | SECOND POSITION |
| 3ANK | SINGLE POSITION |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAC2.0*;ABKRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAC2.0*;ABPMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXD*JBUSHING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A BUSHING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXDJAC2.0*;ABXDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAA2.0*;ADAQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBW*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBWJAC2.0*;AEBWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBX*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO DIAMETER
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE DIAMETER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBXJAA2.0*;AEBXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEHT*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHTJAA2.0*;AEHTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUN*JCENTER TO CENTER DISTANCE BETWEEN COVER PLATE MOUNTING HOLES
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUNJAB2.0*;AFUNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWB*JHOUSING DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOUSING, AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWBJAA2.0*;AFWBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWC*JHOUSING HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWCJAB2.0*;AFWCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWD*JHOUSING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOUSING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWDJAB2.0*;AFWDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWE*JHOUSING WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HOUSING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWEJAB2.0*;AFWEJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWF*JHOUSING BUSHING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWFJAC2.0*;AFWFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWG*JCENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWGJAA2.0*;AFWGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWH*JCENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWHJAB2.0*;AFWHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWJ*JCENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWJJAB2.0*;AFWJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJWX*JMOUNTING SURFACE TO TERMINAL END DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJWXJAB2.0*;AJWXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWYZ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING SUPPORT AND NEAREST TERMINAL
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWYZJAB2.0*;CWYZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AFCG*ASWITCH ACTUATOR QUANTITY
THE NUMBER OF ACTUATORS PROVIDED IN THE ITEM FOR SELECTION OF SWITCHING POSITIONS.
Enter the numeric reply with a minimum of one digit.
(AFCGA10*)
AFGK*JACTUATOR LENGTH
THE MEASUREMENT OF THE DISTANCE THAT THE ACTUATOR PROTRUDES FROM THE BODY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFGKJAB2.0*;AFGKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUR*JACTUATOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACTUATOR,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFURJAC2.0*;AFURJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUS*JACTUATOR HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUSJAA2.0*;AFUSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUT*JACTUATOR WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACTUATOR,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUTJAB2.0*;AFUTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUU*JACTUATOR FREE POSITION HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUUJAB2.0*;AFUUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUV*JACTUATOR ROLLER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUVJAC2.0*;AFUVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFUW*JACTUATOR ROLLER WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFUWJAA2.0*;AFUWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSJN*JSWITCH ACTUATING FORCE
THE AMOUNT OF FORCE REQUIRED TO ACTUATE THE SWITCH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSJNJAB2.0*;CSJNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA56) | Reply |
| C | AMPERE-TURNS |
| D | CENTIMETER-GRAMS |
| E | GRAMS |
| A | INCH-OUNCES |
| W | NEWTONS |
| H | OUNCES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRRM*JSWITCH RELEASE FORCE
THE AMOUNT TO WHICH THE ACTUATING FORCE MUST BE REDUCED TO PERMIT THE SWITCH TO BECOME UNACTUATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRRMJEC2.0*;CRRMJEC2.0$$JEC2.1*)
| Table 1 |
| Reply Code (AA56) | Reply |
| C | AMPERE-TURNS |
| D | CENTIMETER-GRAMS |
| E | GRAMS |
| A | INCH-OUNCES |
| W | NEWTONS |
| H | OUNCES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXQQ*JACTUATOR MOVEMENT
THE MOVEMENT OF THE SWITCH ACTUATOR.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQQJAFLB2.0*;CXQQJAFLB2.0$$JAFLB2.1*)
| Table 1 |
| Reply Code (AL77) | Reply |
| AF | DIFFERENTIAL |
| BN | OVERTRAVEL |
| BM | PRETRAVEL |
| Table 2 |
| Reply Code (AA05) | Reply |
| D | DEGREES |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 5, 7, 8 OR 26 WERE ENTERED FOR MRC AFVV, YOU MUST ANSWER MRC (AFVY and AFVX)
IF STYLE/REPLY CODE(s) 2, 3, 4 OR 6 WERE ENTERED FOR MRC AFVV, YOU MUST ANSWER MRC (AFVX)
IF STYLE/REPLY CODE(s) 9, 10, 11, 12, 13, 14 OR 31 WERE ENTERED FOR MRC AFVV, YOU MUST ANSWER MRC (AFVY)
AFVV*LACTUATOR ADAPTER STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ACTUATOR ADAPTER.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AFVVL14)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AN10321 | 1 | PUSHBUTTON |
| AN10330 | 10 | PUSHBUTTON |
| AN10331 | 11 | PUSHBUTTON |
| AN10332 | 12 | PUSHBUTTON |
| AN10333 | 13 | ROLLER PLUNGER |
| AN10334 | 14 | PUSHBUTTON |
| AN10335 | 15 | ROLLER LEAF |
| AN10336 | 16 | LEAF |
| AN10337 | 17 | ROLLER ARM |
| AN10338 | 18 | ROLLER ARM |
| AN10339 | 19 | ROLLER ARM |
| AN10322 | 2 | PUSHBUTTON |
| AN10340 | 20 | LEAF |
| AN10341 | 21 | LEAF |
| AN10342 | 22 | WIRE |
| AN10343 | 23 | ROLLER ARM |
| AN10344 | 24 | NONADJUSTABLE ARM |
| AN10345 | 25 | NONADJUSTABLE ARM |
| AN10346 | 26 | PUSH |
| AN10347 | 27 | PUSHBUTTON |
| AN10378 | 28 | LEAF |
| AN10348 | 29 | ROLLER LEAF |
| AN10323 | 3 | PUSHBUTTON |
| AN10349 | 30 | ROLLER LEAF |
| AN10350 | 31 | ROLLER PLUNGER |
| AN10324 | 4 | PUSHBUTTON |
| AN10325 | 5 | PUSHBUTTON |
| AN10326 | 6 | PUSHBUTTON |
| AN10327 | 7 | PUSHBUTTON |
| AN10328 | 8 | PUSHBUTTON |
| AN10329 | 9 | PUSHBUTTON |
AFVX*JADAPTER BUSHING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFVXJAA2.0*;AFVXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFVY*JCENTER TO CENTER DISTANCE BETWEEN ADAPTER MOUNTING FACILITIES PARALLEL TO LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFVYJAA2.0*;AFVYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDGC*;ABFEDAB$$DES*)
| Table 1 |
| Reply Code (AB27) | Reply |
| AA | ACID RESISTANT |
| BN | AIRTIGHT |
| AB | CEMENT TIGHT |
| ED | CORROSION PROOF |
| DJ | CORROSION RESISTANT |
| FS | DRIPTIGHT |
| CF | DUSTPROOF |
| CE | EXPLOSION PROOF |
| DN | FLAME RESISTANT |
| GF | FLAMEPROOF |
| DK | FUNGUS PROOF |
| CH | FUNGUS RESISTANT |
| DR | HEAT RESISTANT |
| GE | HUMIDITY RESISTANT |
| BQ | INDUSTRIAL USE |
| DV | MOISTURE PROOF |
| BR | MOISTURE RESISTANT |
| DW | OIL RESISTANT |
| CJ | OILTIGHT |
| EL | PRESSURE PROOF |
| EM | RAINTIGHT |
| GC | SALT SPRAY PROOF |
| FZ | SALT SPRAY RESISTANT |
| DT | SALT WATER RESISTANT |
| FY | SAND PROOF |
| EJ | SHOCK PROOF |
| EP | SHOCK RESISTANT |
| BT | SPLASHPROOF |
| DZ | SUBMERSIBLE |
| ES | VAPORTIGHT |
| GB | VIBRATION RESISTANT |
| EA | WATER RESISTANT |
| CM | WATERPROOF |
| CN | WATERTIGHT |
| EG | WEATHER RESISTANT |
| DX | WEATHERPROOF |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAB2.0*;AEBVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDGR0000*;HUESDBL0000$DPU0000*;HUESDBL0000$$DPU0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BE0000 | BEIGE |
| BL0000 | BLACK |
| BU0000 | BLUE |
| BR0000 | BROWN |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| RG0000 | ORANGE |
| PK0000 | PINK |
| PU0000 | PURPLE |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
ANNY*AQUANTITY WITHIN EACH IMMEDIATE CONTAINER
THE NUMBER OF ITEMS WITHIN EACH IMMEDIATE CONTAINER.
Enter the alpha-numeric reply with a minimum of one character.
(ANNYAA2)
CTJS*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMERED BY PACKAGING OR PACKING MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJSJLBA2.0*;CTJSJLBA2.0$JLBA2.0*;CTJSJLBA2.0$$JLBA2.1*)
| Table 1 |
| Reply Code (AN75) | Reply |
| GM | GRAMS |
| OZ | OUNCES |
| LB | POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX) or (CQJX and AAJD)
IF STYLE/REPLY CODE(s) NC OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD)
IF STYLE/REPLY CODE(s) JC, JE, JF, NE, NF OR NJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJD)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDNC*;THSDDNE$$DJF*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAP1)
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAM3)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBLH*;CBBLDCFB$$DGNN*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AGK | ACTUATOR SEAL |
| ASQ | ADJUSTABLE |
| GNN | ADJUSTABLE TIMER |
| AGL | CARTRIDGE FUSEHOLDER |
| ADM | ELECTRICAL ACCESS PORT |
| DAS | FOUR-WAY SPLIT LENS |
| DAT | FULL DISPLAY LENS |
| CFB | HOLDING MECHANISM |
| AGM | HOLDING SOLENOID |
| DAU | HORIZONTAL SPLIT LENS |
| BLH | LAMP HOLDER |
| AAJ | MOUNTING HARDWARE |
| AGN | NEUTRAL TERMINAL |
| DAV | NONADJUSTABLE |
| AJK | NONTURN FEATURE |
| AGA | O RING |
| AGP | PLUG FUSEHOLDER |
| AJP | REMOVABLE LIGHT FILTER |
| AGQ | RFI SHIELDING |
| FNY | ROHS DIRECTIVE COMPLIANCE |
| DAW | THREE-WAY SPLIT LENS |
| FCY | TIMER |
| ANF | VARIABLE RESISTOR |
| DAX | VERTICAL SPLIT LENS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$JAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)