A capacitor, whose capacitance value cannot be adjusted or varied, having natural sheet mica or reconstituted flaked mica formed into sheets as the dielectric material.It may be a single unit, or consist of two or more fixed units which cannot be separated.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00005*)
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3CEPDNLB000*;MATT3CEPDNLB000$DPCCB00*;MATT3CEPDNLB000$$DPCCB00*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3CEP | CASE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL7075 | ALUMINUM ALLOY 7075 |
| BND000 | BRONZE |
| BNAAAA | BRONZE CAST |
| CLD000 | CERAMIC |
| CRA000 | CHROMIUM |
| CRB000 | CHROMIUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| FBA000 | FIBER |
| FG0000 | FIBERGLASS |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| RBR000 | HARD RUBBER |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| LRA000 | LEATHER |
| LRE000 | LEATHER ARTIFICIAL |
| MGB000 | MAGNESIUM ALLOY |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCJ000 | PLASTIC MELAMINE |
| PCCB00 | PLASTIC NYLON |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAK00 | PLASTIC SILICONE |
| PCBC00 | PLASTIC STYRENE |
| CLB000 | PORCELAIN |
| STA000 | STEEL |
| ST0302 | STEEL COMP 302 |
| ST0304 | STEEL COMP 304 |
| ST0316 | STEEL COMP 316 |
| STB000 | STEEL CORROSION RESISTING |
| AAA012 | THERMOPLASTIC |
| WDC000 | WOOD |
| WDL000 | WOOD MAHOGANY |
| WDR000 | WOOD OAK |
| WDE000 | WOOD WALNUT |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
BWGP*ASECTION QUANTITY
THE NUMBER OF SECTIONS INCLUDED.
Enter the numeric reply with a minimum of one digit.
(BWGPA10*)
CQBQJCAPACITANCE VALUE PER SECTION
THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRIC CHARGE AT A GIVEN POTENTIAL WHICH THE CAPACITOR IS CAPABLE OF RECEIVING AND STORING PER SECTION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQBQJUFDA2.0*;CQBQJUFDA2.0$JUFDA2.0*;CQBQJUFDA2.0$$JUFDA2.1*)
| Table 1 |
| Reply Code (AN86) | Reply |
| UF | MICROFARADS |
| LF | MILLIFARADS |
| NF | NANOFARADS |
| PF | PICOFARADS |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
CRTPJTOLERANCE RANGE PER SECTION
THE LIMITS OF PERMISSIBLE DEVIATION PER SECTION OF A MEASURED VALUE FROM A SPECIFIED VALUE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRTPJPFCPM32.0/P50.0*;CRTPJPFCPM32.0/P50.0$$JPFCP*;CRTPJPFCPM32.0/P50.0$JPFCPM32.0/P50.0*)
| Table 1 |
| Reply Code (AN86) | Reply |
| UF | MICROFARADS |
| LF | MILLIFARADS |
| NF | NANOFARADS |
| PC | PERCENT |
| PF | PICOFARADS |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
CQWMJNONDERATED CONTINUOUS VOLTAGE RATING AND TYPE PER SECTION
THE HIGHEST VALUE AND TYPE OF POTENTIAL THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM PER SECTION AT THE HIGHEST OPERATING TEMPERATURE PERMISSIBLE WITHOUT VOLTAGE DERATING.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQWMJAPCZ2.0*;CQWMJAPCZ2.0$JAPCZ2.0*;CQWMJAPCZ2.0$$JAPCZ2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AD | AC/DC |
| AP | AC-PEAK |
| AR | AC-RMS |
| DC | DC |
| Table 2 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
CRDNJTEMP COEFFICIENT OF CAPACITANCE RANGE PER SECTION IN PPM PER DEG CELSIUS
THE MINIMUM AND MAXIMUM VALUES OF THE PERMISSIBLE CHANGE IN CAPACITANCE PER SECTION CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRDNJDAM32.0/P50.0*;CRDNJDAM32.0/P50.0$$JDA*;CRDNJDAM32.0/P50.0$JDAM32.0/P50.0*)
| Table 1 |
| Reply Code (AH19) | Reply |
| DA | 10TH SECTION |
| CP | 1ST SECTION |
| CQ | 2ND SECTION |
| CR | 3RD SECTION |
| CS | 4TH SECTION |
| CT | 5TH SECTION |
| CW | 6TH SECTION |
| CX | 7TH SECTION |
| CY | 8TH SECTION |
| CZ | 9TH SECTION |
| CM | ALL SECTIONS |
| CN | SINGLE SECTION |
CQJJJNONDERATED OPERATING TEMP
THE TEMPERATURE/S/ AT WHICH AN ITEM CAN FUNCTION WITHOUT VOLTAGE DERATING.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJJJFC2.0*;CQJJJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1A, 2A, 3A, 4A, 5A, 6A, 7A, 8A, 9A, 10A, 11A, 12A, 13A, 14A, 15A, 16A, 17A, 18A, 19A, 20A, 21A, 22A, 23A, 24A, 25A, 26A, 27A, 28A, 29A, 30A, 31A, 32A, 33A, 34A, 35A, 36A, 37A, 38A, 39A, 40A, 41A, 42A, 43A, 44A, 45A, 46A, 47A OR 48A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAU and ADAQ and ADAT)
IF STYLE/REPLY CODE(s) 1B, 2B, 3B, 4B, 5B, 6B, 7B, 8B, 9B, 10B, 11B, 12B, 14B, 15B, 16B, 17B, 18B, 19B, 20B, 21B, 22B, 23B, 25B, 26B, 27B, 28B, 29B, 30B, 31B, 33B, 34B, 35B, 37B, 38B, 39B, 40B, 41B, 42B, 43B, 44B, 45B, 46B, 47B, 48B, 49B, 50B, 51B, 52B, 53B, 55B, 56B, 57B, 58B OR 59B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ)
IF STYLE/REPLY CODE(s) 13B OR 54B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ASDB)
IF STYLE/REPLY CODE(s) 24B OR 32B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABPM and ADAQ and ASDB)
IF STYLE/REPLY CODE(s) 36B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAT and ADAQ and ADAU)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL9B)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAE1010 | 10A | W/THD MTG HOLE(S)/STUD(S), TERMINAL(S) ON ONE SURFACE |
| AAE1058 | 10B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1011 | 11A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1059 | 11B | W/O MTG FACILITIES, TERMINALS ON OPPOSITE ENDS |
| AAE1012 | 12A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1060 | 12B | W/MTG TAB(S), TERMINAL(S) ON ONE END |
| AAE1013 | 13A | W/O MTG FACILITIES, TERMINAL(S) ON ONE SURFACE |
| AAE1061 | 13B | W/THD BUSHING MTG, TERMINALS ON OPPOSITE END |
| AAE1014 | 14A | W/O MTG FACILITIES, TERMINAL(S) ON ONE SURFACE |
| AAE1062 | 14B | W/THD MTG HOLE, TERMINAL(S) ON ONE END |
| AAE1015 | 15A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1063 | 15B | W/THD BUSHING MTG, TERMINALS ON OPPOSITE ENDS |
| AAE1016 | 16A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1064 | 16B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1017 | 17A | W/THD MTG HOLE(S)/STUD(S), TERMINAL(S) ON ONE SURFACE |
| AAE1065 | 17B | W/O MTG FACILITIES, RADIAL TERMINALS |
| AAE1018 | 18A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1066 | 18B | W/O MTG FACILITIES, AXIAL AND RADIAL TERMINALS |
| AAE1019 | 19A | W/THD MTG HOLE(S)/STUD(S) TERMINAL(S) ON ONE SURFACE |
| AAE1067 | 19B | W/MTG FLANGE, TERMINAL(S) ON ONE END |
| AAE1001 | 1A | W/MTG TABS/FLANGES, TERMINALS ON OPPOSITE SURFACES |
| AAE1049 | 1B | W/O MTG FACILITIES, TERMINAL(S) ON ONE END |
| AAE1020 | 20A | WITHOUT MOUNTING FACILITIES, TERMINAL(S) ON ONE SURFACE |
| AAE1068 | 20B | W/MTG BRACKET, TERMINALS ON OPPOSITE ENDS |
| AAE1021 | 21A | W/O MTG FACILITIES, TERMINALS ON OPPOSITE SURFACES |
| AAE1069 | 21B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1022 | 22A | W/MTG TABS/FLANGES, TERMINALS ON OPPOSITE SURFACES |
| AAE1070 | 22B | W/O MTG FACILITIES, RADIAL TERMINALS |
| AAE1023 | 23A | W/THD MTG HOLE(S)/STUD(S) TERMINALS ON ONE SURFACE |
| AAE1071 | 23B | W/O MTG FACILITIES, RADIAL TERMINALS |
| AAE1024 | 24A | W/MTG TAB/FLANGE, TERMINALS ON OPPOSITE SURFACE |
| AAE1072 | 24B | W/THD MTG HOLE/STUD, RADIAL TERMINAL(S) |
| AAE1025 | 25A | W/THD MTG HOLE(S)/STUD(S), TERMINAL(S) ON ONE SURFACE |
| AAE1073 | 25B | RADIAL TERMINAL(S) |
| AAE1026 | 26A | W/MTG TAB, TERMINAL(S) ON ONE SURFACE |
| AAE1074 | 26B | W/O MTG FACILITIES, AXIAL TERMINALS |
| AAE1027 | 27A | W/O MTG FACILITIES TERMINAL(S) ON ONE SURFACE |
| AAE1075 | 27B | W/MTG BRACKET, AXIAL TERMINALS |
| AAE1028 | 28A | W/O MTG FACILITIES, TERMINAL(S) ON ONE SURFACE |
| AAE1076 | 28B | W/MTG BRACKET, AXIAL TERMINALS |
| AAE1029 | 29A | W/O MTG FACILITIES, TERMINAL(S) ON ONE SURFACE |
| AAE1077 | 29B | W/THD MTG STUDS, AXIAL TERMINALS |
| AAE1002 | 2A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1050 | 2B | W/TWIST TAB MTG, TERMINAL(S) ON ONE END |
| AAE1030 | 30A | W/THD HOLE(S)/STUD(S), TERMINAL(S) ON ONE SURFACE |
| AAE1078 | 30B | W/THD MTG HOLE/STUD, TERMINAL(S) ON ONE END |
| AAE1031 | 31A | W/MTG TAB(S)/FLANGE(S), TERMINAL(S) ON ONE SURFACE |
| AAE1079 | 31B | W/MTG BRACKET, TERMINALS ON OPPOSITE ENDS |
| AAE1032 | 32A | W/MTG TAB(S)/FLANGE(S), TERMINAL(S) ON ONE SURFACE |
| AAE1080 | 32B | W/THD MTG HOLE/STUD, TERMINAL(S) ON ONE END |
| AAE1033 | 33A | W/O MTG HOLE(S)/SLOT(S), TERMINAL(S) ON ONE SURFACE |
| AAE1081 | 33B | W/O MTG FACILITIES, RADIAL TERMINALS |
| AAE1034 | 34A | W/MTG HOLE(S)/SLOT(S) TERMINAL(S) ON ONE SURFACE |
| AAE1082 | 34B | W/MTG BRACKET, AXIAL TERMINALS |
| AAE1035 | 35A | W/O MTG HOLE(S)/SLOT(S), TERMINALS ON OPPOSITE SURFACE |
| AAE1083 | 35B | W/THD MTG STUDS, TERMINAL(S) ON THE END |
| AAE1036 | 36A | W/MTG HOLE(S)/SLOT(S), TERMINALS ON OPPOSITE SURFACES |
| AAE1084 | 36B | W/O MTG FACILITIES, RADIAL TERMINALS |
| AAE1037 | 37A | W/MTG TAB, TERMINAL(S) ON ONE SURFACE |
| AAE1085 | 37B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1038 | 38A | W/MTG HOLE(S)/SLOT(S) TERMINALS ON OPPOSITE SURFACES |
| AAE1086 | 38B | CHIP TYPE |
| AAE1039 | 39A | W/MTG HOLE(S)/SLOT(S), TERMINAL(S) ON ONE SURFACE |
| AAE1087 | 39B | BUTTON TYPE, W/MTG TABS |
| AAE1003 | 3A | W/MTG TABS/FLANGES TERMINALS ON OPPOSITE SURFACES |
| AAE1051 | 3B | W/THD MTG STUD, TERMINAL(S) ON ONE END |
| AAE1040 | 40A | CHIP TYPE WITH TAPE TERMINALS |
| AAE1088 | 40B | BUTTON TYPE, W/MTG TABS |
| AAE1041 | 41A | W/MTG HOLE(S)/SLOT(S), TERMINALS ON OPPOSITE SURFACES |
| AAE1089 | 41B | BUTTON TYPE, W/O MTG TABS |
| AAE1042 | 42A | W/THD MTG HOLE(S)/STUD(S), TERMINAL(S) ON ONE SURFACE |
| AAE1090 | 42B | BUTTON TYPE, W/MTG TABS |
| AAE1043 | 43A | W/O MTG FACILITIES, TERMINALS ON OPPOSITE SURFACES |
| AAE1091 | 43B | BUTTON TYPE, W/MTG TABS |
| AAE1044 | 44A | W/MTG HOLE(S)/SLOT(S), TERMINALS ON OPPOSITE SURFACES |
| AAE1092 | 44B | BUTTON TYPE, W/O MTG TABS |
| AAE1045 | 45A | CHIP TYPE |
| AAE1093 | 45B | BUTTON TYPE, W/MTG TABS |
| AAE1046 | 46A | DUAL INLINE |
| AAE1094 | 46B | BUTTON TYPE, W/THD MTG HOLE/STUD |
| AAE1047 | 47A | SINGLE INLINE |
| AAE1095 | 47B | W/THD BODY MTG, AXIAL TERMINALS |
| AAE1048 | 48A | FLAT PACK |
| AAE1096 | 48B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1097 | 49B | W/MTG FLANGES, TERMINALS ON OPPOSITE ENDS |
| AAE1004 | 4A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1052 | 4B | W/THD BUSHING MTG, TERMINAL(S) ON ONE END |
| AAE1098 | 50B | W/MTG FLANGES, TERMINALS ON OPPOSITE ENDS |
| AAE1099 | 51B | W/THD MTG HOLE(S)/STUD(S), TERMINAL(S) ON ONE END |
| AAE1100 | 52B | W/MTG BRACKET, TERMINALS ON OPPOSITE ENDS |
| AAE1101 | 53B | BUTTON TYPE, W/MTG TABS |
| AAE1102 | 54B | W/THD MTG BUSHING, TERMINALS ON OPPOSITE ENDS |
| AAE1103 | 55B | CHIP TYPE |
| AAE1104 | 56B | PELLET TYPE, W/O MTG TABS |
| AAE1105 | 57B | PELLET TYPE, W/MTG TABS |
| AAE1106 | 58B | PELLET TYPE, W/MTG PINS |
| AAE1107 | 59B | PELLET TYPE, W/THD MTG HOLE/STUD |
| AAE1005 | 5A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1053 | 5B | W/MTG BRACKET TERMINAL(S) ON ONE END |
| AAE1006 | 6A | W/MTG TABS/FLANGES TERMINAL(S) ON ONE SURFACE |
| AAE1054 | 6B | W/MTG BRACKET, TERMINAL(S) ON ONE END |
| AAE1007 | 7A | W/MTG TABS/FLANGES, TERMINAL(S) ON ONE SURFACE |
| AAE1055 | 7B | W/MTG TAB(S), TERMINAL(S) ON ONE END |
| AAE1008 | 8A | W/MTG TABS/FLANGES TERMINAL(S) ON ONE SURFACE |
| AAE1056 | 8B | W/MTG TAB(S), TERMINAL(S) ON ONE END |
| AAE1009 | 9A | W/THD MTG HOLE(S)/STUD(S) TERMINAL(S) ON ONE SURFACE |
| AAE1057 | 9B | W/MTG STUD(S), TERMINAL(S) ON ONE END |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAB2.0*;ABPMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAB2.0*;ADAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAC2.0*;ADATJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBZLSCHEMATIC DIAGRAM DESIGNATOR
A DESIGNATOR INDICATING A GRAPHIC REPRESENTATION,IN STANDARD AND ACCEPTED SYMBOLS,OF ESSENTIAL ELECTRICAL-ELECTRONIC ELEMENTS AND RELATED CONNECTIONS ON THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AEBZL1C)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAE1117 | 10C | DELTA CONNECTED |
| AAE1118 | 11C | DELTA, CONNECTED, GROUNDED TO CASE |
| AAE1119 | 12C | QUAD, ONE COMMON TERMINAL FOR EACH PAIR |
| AAE1120 | 13C | ONE TERMINAL COMMON TO EACH SECTION, W/TWO COMMON DUMMY TERMINALS |
| AAE1121 | 14C | QUAD, ONE SEPARATE, THREE W/COMMON TERMINAL |
| AAE1122 | 15C | EACH SECTION GROUNDED TO CASE, TWO COMMON TERMINALS FOR EACH SECTION |
| AAE1123 | 16C | SERIES CONNECTED |
| AAE1124 | 17C | FEEDTHROUGH |
| AAE1125 | 18C | ONE TERMINAL COMMON TO EACH SECTION, ONE TERMINAL GROUNDED TO CASE |
| AAE1126 | 19C | THREE TERMINALS COMMON TO ONE ELECTRODE, ONE ELECTRODE GROUNDED TO CASE |
| AAE1108 | 1C | NO COMMON OR GROUNDED ELECTRODE(S) |
| AAE1127 | 20C | TWO TERMINALS COMMON TO ONE ELECTRODE, ONE ELECTRODE GROUNDED TO CASE |
| AAE1128 | 21C | NO COMMON OR GROUNDED ELECTRODES, W/SEPARATE CASE TERMINAL |
| AAE1109 | 2C | ELECTRODE(S) GROUNDED TO CASE |
| AAE1110 | 3C | ELECTRODE(S) GROUNDED TO CASE, W/GND TERMINAL |
| AAE1111 | 4C | TWO TERMINALS COMMON TO ONE ELECTRODE |
| AAE1112 | 5C | TWO COMMON TERMINALS FOR EACH ELECTRODE |
| AAE1113 | 6C | DUAL, ONE ELECTRODE GROUNDED TO CASE |
| AAE1114 | 7C | ONE TERMINAL COMMON TO EACH SECTION |
| AAE1115 | 8C | TRIPLE, ONE SEPARATE, TWO W/COMMON TERMINAL |
| AAE1116 | 9C | SERIES CONNECTED, END TERMINAL GROUNDED TO CASE |
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAE2*;TTQYJAAE2$$JAAE3*;TTQYJAAE2$JAAE2*)
| Table 1 |
| Reply Code (AN89) | Reply |
| AAB | BANANA PLUG |
| AAC | BAYONET |
| AAD | BONDING PAD |
| AAE | BONDING PAD W/STANDOFF CONES |
| AEP | CABLE W/CONNECTOR |
| AAF | CONNECTOR, RECEPTACLE |
| AAG | EYELET W/WIRE LEAD |
| AAH | FERRULE |
| AAJ | FLANGE |
| AAK | INSULATED WIRE LEAD |
| AAL | INSULATED WIRE LEAD W/TERMINAL LUG |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| ADA | QUICK DISCONNECT, FEMALE |
| AAN | QUICK DISCONNECT, MALE, DOUBLE BLADE |
| ALS | QUICK DISCONNECT, MALE, FOUR BLADE |
| AAP | QUICK DISCONNECT, MALE, SINGLE BLADE |
| AAQ | QUICK DISCONNECT, MALE, SINGLE BLADE W/SOLDER HOLE |
| ALU | QUICK DISCONNECT, MALE, THREE BLADE |
| AAR | RIBBON |
| AAS | SOLDER STUD |
| AHK | SPRING CLIP |
| AAT | STANDARD TUBE BASE |
| AAW | STANDOFF, SOLDER LUG |
| AAX | STANDOFF, SOLDER STUD |
| AAY | STANDOFF, THREADED STUD |
| AAZ | STANDOFF, WIRE HOOK/LOOP |
| ABA | STANDOFF, WIRE LEAD |
| ABB | TAB, SOLDER LUG |
| ABC | THREADED HOLE |
| ALX | THREADED HOLE W/TERMINAL LUG |
| ABD | THREADED STUD |
| ALZ | THREADED STUD W/TERMINAL LUG |
| ABF | UNINSULATED WIRE LEAD |
| ABG | UNINSULATED WIRE LEAD W/TERMINAL LUG |
| ABH | UNTHREADED HOLE |
| ABE | U-SHAPED TAB |
| ABJ | WIRE BRAID |
| ABK | WIRE HOOK/LOOP |
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBU*JTERMINAL HEIGHT FROM BODY
THE DISTANCE FROM THE END OF THE TERMINAL TO THE BODY OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBUJAA2.0*;AEBUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBT*JTERMINAL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBTJAC2.0*;AEBTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBP*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO LENGTH
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE LENGTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBPJAA2.0*;AEBPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBQ*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO WIDTH
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE WIDTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBQJAA2.0*;AEBQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBS*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO DIAMETER
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE DIAMETER OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBSJAB2.0*;AEBSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWSZ*DCASE INSULATION MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CASE INSULATION IS FABRICATED.
Enter the applicable reply code from the table below
(CWSZDPCA000*;CWSZDPPA000$DRCE000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| RCE000 | RUBBER |
IF STYLE/REPLY CODE(s) AAZ WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AEBV)
IF STYLE/REPLY CODE(s) AAQ, AAW OR AFA WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AKEJ and CQJX)
IF STYLE/REPLY CODE(s) AAL WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (ABTD)
AXHR*JMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJAAQ2*;AXHRJAAQ2$$JAAQ3*)
| Table 1 |
| Reply Code (AM39) | Reply |
| AAL | MOUNTING SLOTS |
| AFA | THREADED BUSHING |
| AAQ | THREADED MOUNTING HOLES |
| AAW | THREADED MOUNTING STUDS |
| AAZ | UNTHREADED MOUNTING HOLES |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAB2.0*;AEBVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) JC, JE, JF, JS, NC, NE, NF, NJ, NS OR UN WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CQQR)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CQQR and CTTC)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC AKEJ, YOU MUST ANSWER MRC (CQJX and CQQR) or (CQJX and CTTC)
AKEJ*DMOUNTING FACILITY SCREW THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE MOUNTING FACILITY.
Enter the applicable reply code from the table below
(AKEJDNC*;AKEJDNF$DEM*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0*;CQQRB2.02.0$BM2.0*)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJEXTTEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
AEBY*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY LENGTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE LENGTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBYJAC2.0*;AEBYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEHA*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY WIDTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE WIDTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHAJAB2.0*;AEHAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBW*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBWJAB2.0*;AEBWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBX*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO DIAMETER
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE DIAMETER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBXJAB2.0*;AEBXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWPK*JINSULATION RESISTANCE AT REFERENCE TEMP
DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT REFERENCE TEMPERATURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWPKJMU2.0*)
| Table 1 |
| Reply Code (AN86) | Reply |
| MU | MEGOHM-MICROFARADS |
| MZ | MEGOHMS |
CWPM*BDISSIPATION FACTOR AT REFERENCE TEMP IN PERCENT
THE RATIO OF RESISTANCE TO CAPACITIVE REACTANCE MEASURED AT REFERENCE TEMPERATURE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CWPMB2.0)
CWQF*BQUALITY FACTOR AT REFERENCE TEMP
THE RATIO OF CAPACITIVE REACTANCE TO RESISTANCE,MEASURED AT REFERENCE TEMPERATURE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CWQFB2.0)
CWQQ*JREFERENCE TEMP AT WHICH RATED
THE REFERENCE TEMPERATURE AT WHICH A RATING IS ESTABLISHED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWQQJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AARGDRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDE)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
AARH*BRELIABILITY FAILURE RATE LEVEL IN PERCENT
THE RATE OF FAILURE DETERMINED UNDER SPECIFIED CONDITIONS TO ESTABLISH THE RELIABILITY OF AN ITEM,EXPRESSED IN PERCENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AARHB2.0)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCQE*;CBBLDBPR$$DCQH*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BSG | BURN IN |
| AAH | HERMETICALLY SEALED CASE |
| CQE | HIGH SCREW INSERT |
| CQF | LOW SCREW INSERT |
| AAJ | MOUNTING HARDWARE |
| BWJ | PALLADIUM FREE |
| CQG | POSITIVE TERMINAL GROUNDED |
| BWQ | RADIATION HARDENED |
| CQH | W/BLEEDER RESISTOR |
| BPR | W/BOOT |
| BYK | W/FORMED LEADS |
| CQJ | W/SAFETY VENT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
AARD*ADUMMY TERMINAL QUANTITY
THE NUMBER OF TERMINALS THAT DO NOT PROVIDE ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARDA10*)
AARF*AMIL-STD-1276 WIRE LEAD TYPE DESIGNATOR
INDICATES THE TYPE DESIGNATOR,PER MIL-STD-1276,OF THE DETAIL REQUIREMENTS OF LEADS USED ON ELECTRONIC COMPONENTS.
Enter the alpha-numeric reply with a minimum of one character.
(AARFAA0)
CWSG*DTERMINAL SURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE TERMINAL SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(CWSGDCDA000*;CWSGDAGA000$DCUA000*;CWSGDAGA000$$DCUA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| CDA000 | CADMIUM |
| CUA000 | COPPER |
| AUA000 | GOLD |
| NLA000 | NICKEL |
| PDA000 | PALLADIUM |
| AGA000 | SILVER |
| SRA000 | SOLDER |
AEBK*BMAXIMUM RF CURRENT RATING AT HIGHEST RATED FREQUENCY IN RMS AMPS
THE MAXIMUM ALTERNATING CURRENT THAT MAY FLOW THROUGH THE ITEM AT THE HIGHEST FREQUENCY ABOVE THREE KILOHERTZ.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEBKB2.0)
AEBL*BHIGHEST FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ
THE MAXIMUM FREQUENCY,HIGHER THAN THREE KILOHERTZ,AT WHICH A MAXIMUM ALTERNATING CURRENT RATING HAS BEEN ESTABLISHED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEBLB2.0)
AEBM*BMAXIMUM RF CURRENT RATING AT LOWEST RATED FREQUENCY IN RMS AMPS
THE MAXIMUM ALTERNATING CURRENT THAT MAY FLOW THROUGH THE ITEM AT THE LOWEST FREQUENCY ABOVE THREE KILOHERTZ.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEBMB2.0)
AEBN*BLOWEST FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ
THE MINIMUM FREQUENCY,HIGHER THAN THREE KILOHERTZ,AT WHICH A MAXIMUM ALTERNATING CURRENT RATING HAS BEEN ESTABLISHED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEBNB2.0)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CQBF*JINSULATION RESISTANCE AT MAXIMUM OPERATING TEMP
DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT THE MAXIMUM OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQBFJMU2.0*)
| Table 1 |
| Reply Code (AN86) | Reply |
| MU | MEGOHM-MICROFARADS |
| MZ | MEGOHMS |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| C | MAXIMUM |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information